Hammer angle grinder or angle grinder DILD which is better?
Hammer USM 850 A angle grinder reviews
Alexey N. Advantages: Second year of use and has not even replaced the brushes. They say that a miser pays twice, but there are exceptions and this tool falls into that category. Disadvantages: Could not find. Comment: I am satisfied. My recommendations.
Expert-N. Advantages: Low weight Disadvantages: The button fixing the rotor is hard to fix, tears off, to change the disc fixes very badly, incredibly hard to push to stop the ratchet. The disk did not bite while sawing.Dismantled to see what’s wrong, all new in the grease, but the holes are not deep drilled, the spindle itself is much smaller than the hole and so slips out.I will try to put a spacer from an interskol. Do not recommend the use of a month.
Hammer USM 500 LE angle grinder reviews
Dmitry Yoo. Advantages: Cheap, sulfuric, convenient and of high qualityComment: angle grinder is not intended for long and exhausting works under the maximum load. For home use. great option
Advantages: easy to use, works fine!Disadvantages: Did not see yet.comment: handy product, high quality workmanship, low price. The noise and vibration is insignificant. The quality and price I am completely satisfied, so my purchase is satisfied.
Hammer USM850B PREMIUM angle grinder reviews
Ramil Ramazanov Advantages: Price tag. Build. Disadvantages: No problems so far. Comment: I bought this angle grinder mainly for cutting fixtures. A pack of 2-3 tons of grates without overheating. Diameter of the disk allows to cut a 69 pipe. I am satisfied with the grinder. Didn’t regret getting it.
The White Warrior: I can mention a few pros right away. the build, the speed, the power and the price. Disadvantages: I have not noticed any disadvantages. Комментарии и мнения владельцев: When I chose the grinder in the first place was guided by the price and power, because free money was not much. I have not regretted that I did not take more expensive analogues, because the angle grinder suited me in terms of capabilities and functionality, and the Hammer somehow became more trustworthy.
Hammer USM 600 C PREMIUM angle grinder reviews
Vyacheslav M. Advantages: Similar to other similar devices with similar power.Disadvantages: Quickly broke the rotor stop button. Disassembled. Checked out. Made of some kind of silumin. Just wore off. In a couple of months.comment: Was given as a gift. Price ok. 2 т.р. Better to look in the direction of analogues from famous brands.
Valery S. Advantages: Small and light angle grinder, handy on-off button (one of my criteria for selection) and a grip body.The Disadvantages: After a short time of use refused to turn off.Комментарии и мнения владельцев: Can be said to be my first angle grinder. Bought for use in the country on the farm. But decided to drive it until two weeks to return it.During the first use the speed briefly rpm without load (I heard it or not, but it did not happen again).After the second use (a small kerf in sheet metal), the angle grinder refused to turn off I had to pull out of the socket.I didn’t dare to try it again when returning and bought the Metabo.I can not say that all angle grinders are bad, so I give them three stars. I do not have time to buy it, I just do not have time to run to the store.I liked the machine itself in terms of convenience, workmanship and price.Probably ran into a manufacturing defect.
Hammer USM 850 angle grinder reviews
Ilya e. The advantages: I bought it not so long ago but I can already say a few positive things. The price is inexpensive, the torque is good, the power is great. It is assembled with high quality and thoroughly reliable. Does not break, does not overheat, does not fail.Disadvantages: I am satisfied with it so far, I hope I will not be disappointed.Комментарии и мнения владельцев: Hammer is even cheaper than other manufacturers, at least for the most part, so I think I got lucky with the purchase.
Hammer USM 500 angle grinder reviews
Igor R. Advantages: good props for making movies for adults ))))Disadvantages: does not work.comment: it is not a tool, just a prop! got almost a free suitcase. an angle grinder, a jigsaw, a drill. everything is disposable. I used the angle grinder only once. first there was a smell, then smoke. the whole angle grinder came out with the smoke. burned out in 10 minutes. With the rest of the tools the same thing. the drill was electrocuted as well.
Roman C. Advantages: price, weightDisadvantages: it is not a toolCommentary: I used it 8-9 times, broke down, stopped turning on, took it to the service, repaired the type, used 2 times, the warranty period expired, broke the cooling blades collapsed. Waste of money. Bought a normal.
Hammer USM 1050 A angle grinder reviews
Vlad K. Advantages: Price, powerRPM control, very handy handle and buttonDisadvantages: Poor lock to change the disc (one wiped out completely, two barely alive) Under heavy load the speed drops noticeably (holding turns under load is not) backlash in the gearbox (as luck would have it) Comment: The best angle grinder in this price segment, despite the price and the lack of dust protection has successfully survived two repairs, she cut a lot of chips (in aerated concrete, bricks and concrete), rebar, etc.д.
Manchilin-alexandr Advantages: Easy to use, light weight, adjustable speed, power, price and quality.Weaknesses: No soft start.comment: I bought this angle grinder to replace the old, which spent 5 years. A big plus that the starter button is made as a button, ie.The angle grinder is okay, even made not deep dowels in the concrete with a diamond wheel. The reducer was turned around for convenient operation and it was additionally lubricated. Long power cord. Satisfied with the purchase, a huge plus is its low price at the time of purchase.
Hammer USM 2100 A angle grinder reviews
martynov and. Advantages: Price, quality, manufacturer, reliability.comment: I bought my Hammer torch and this machine at the same time. Both have been in use for over 3 months now. The machine is normal, even made no deep chisels in the concrete with a diamond wheel. Such a tool should be allowed to cool down. It is not a professional tool, but for household needs.
Paul P. Advantages: I like itDisadvantages: Couldn’t find itCommentary: Smooth and clean. Large disc diameter. Not heavy. Price is adequate.
Hammer USM 2350 A angle grinder reviews
Andryushka C. The advantages: It withstands well over a long load and does not get warm. Used almost daily. angle grinder has already paid off.Disadvantages: I like everything, I am satisfied with the purchase by all means!
How to choose
In this case, the choice of angle grinder initially determined by the diameter of the cutting disc. Next, in order not to overpay for the extra price you need to pick up on the following defining characteristics.
- The maximum power of the tool, which characterizes its performance and motor life, in this class is up to 1900 watts.
- The maximum speed of the spindle depends on the previous indicator and can go up to 12000 rpm, and in some cases even more.
- Diameter of the disc. angle grinder with adjustable speed usually come only with a small disc diameter 115,125 (the most common) and 150 mm, at larger diameters such a function is not provided.
DYOLD MSHU-0,95-125
It is difficult to get the original brushes, I have to take similar ones and re-solder to the original mounts (the 2nd time in 5 years).
Yes heavy, yes bulky, but cheap, but it feels in the hands of the Russian hero of power and reliability. I have no other cutting and grinding tools, I do everything with it, and it “Shelma” plows and plows.
Good angle grinder, has never failed
The only flaw in it. The disk rotation lock button is not protected. It turns out that the plastic head protrudes. Grinding with it in a hard to reach place, caught the button on the iron and that’s it. Cap broke off, now instead of a button I put a nail to clamp the disk
All excellent, durable angle grinder. There is though a little shortcoming of the button to lock the rotation of the disk.
Hard wire, bursts at low temperature.Thick body, fatigue the hand when sanding the walls with paddle discs, which is why it was taken.The brushes that were on the purchase, lasted tolerably.The spare just fell apart after the first minutes of work.We in Kargopol not found on sale native.had to take, another company, notorious, “Sturm” and they wear out quickly.literally enough for a day.and cost 100r.apiece.and moreover it is necessary to adjust to this angle grinder.They don’t even bother to bring it to order.that’s the problem.If you have small jobs, you can take it.if constant, as in my case.luther consider other options.at a higher price.the same Interskol.or Makita,Hitachi.in the photo spare brushes collapsed, brushes.and Sturm, which need to sharpen the iron threshold, so it fits into the body.
Price. Prevalence. Availability of service and spare parts. The possibility of installing an additional handle in the third (middle) position, which is very convenient.
Speed regulation does not start from scratch, but somewhere around 4000 rpm (although maybe it’s just a defect of my angle grinder). During operation (no particular load) for more than 5 minutes. Gears start to get warm.
I am completely satisfied with the tool. I use it occasionally for small repairs at home, in the garage, at the cottage. Has not broken yet. But it is unlikely to be suitable for professional use.
Handy handle, start button with the fuse and without fixation. Not unimportant for safety. Cost less than 1000r at the time of purchase. The power cord is a meter long. I use it often for metal, wood and stone work. Disassembles and cleans easily. There is enough oil in the gearbox from the factory.
After 2 years replaced the start button, the plastic part of the disk detent button broke off. The gearbox is heating, but not critical, although there is oil in the gearbox, and it is enough.
In general the tool is good. In Smolensk, where he was born, no problems with spare parts. The price is still competitive.
I have been using Diold tools for over 10 years. The angle grinder is exploited mercilessly. When grinding wood floor angular grinder Diold enough for six months. And the same Makita does not last for 3-4 months. And the price is different there.
The machine bought 8 years ago that he just did not cut and finally died))) Well, the truth is not precisely may just need to change the bearings. In short, in two words a great machine got, no tears.
Diold has one problem with plastic cables, but at this price you can’t expect better.
Used for cutting and grinding metal and welds. There is also a Makita she only cuts as she grinds hard enough power is not enough 700 watts, you can feel how it strains and grinding dildo only change the circles, I do not know what they write that bad it breaks I do not particularly care when grinding seams sometimes quite strongly and still works, the only thing not convenient that there is no button holder I do not miss it especially when grinding in awkward places. And in general, dilod is not a bad tool for its money I have and peorator and jigsaw for more than a year are faithful and accurate to compare with makita and the like the tool is not correct, because the price difference is enormous, but if you take the competition in the same price range then dilod leader on the price-quality ratio.
I have been using this tool professionally for 3 years, cutting, grinding with different types of circles, I can say I kill mercilessly, but overloading is not allowed. I’ve changed brushes a few times and that’s it. Bought by accident, about 6 years ago, the first thing that caught my eye (just need it urgently) did not even a hint of failure, whirring like a new. Wanted to note-good balancing the armature, no vibration, unlike China. Took it for 1200 p. I guess I was lucky, but maybe the company is really good. I will buy the same company with a little more power
Professionally engaged in construction and 2.5 years ago I bought this angle grinder on the advice of an acquaintance, who spent 15 years selling Chinese tools. China, but the factory and very good quality. Bosch or Makita, also made in the same China with a soft start and adjustable speed for such money you can not buy. At high intensity of work only now failed. It paid for itself 1000 times over. Thought brushes. No, I still have some stock. Anyway, I will buy the same model and keep this one for parts.
The bolt that fastens the protective cover is flattened after the third resetting of the cover’s position. The safety trigger, the one you have to squeeze to safely turn it on, broke after two weeks. The cable is horrible. It is short and stiff, and the attachment to the housing is not secure. Cable breakage after 2 months. Bent the blade removal wrench when trying to remove the cutting wheel while cutting metal (replaced by a wing nut).All seemingly small things, but incredibly annoying.
Workhorse, so much cut, for more than 3 years, plus and as a polisher worked, generally satisfied, changed 2 brushes, and otherwise all super, but the brushes from the large use, not every Makita will do so much
Trigger, handle. the speed control
Short brittle cable, brushes wear out quickly
In general, the machine is satisfied with the cable replaced by a rubber 2h-meter, but the brushes are just sick of changing them every 2-3 months, not constant work in the garage service, it is probably a marriage. For the rest it is all good, convenient, sturdy, but a little heavy for my work.
Handy handle, combined with a start button.Still alive.
Bought in Smolensk in the factory store in the summer of 2007. The price at the time was ridiculous. On the order of “per watt power”. Three years of conditional intensive work in the repair of dacha, metal greenhouse, etc.д. Basically. metal. 2010. work to improve the new apartment (concrete, tiles, rebar). Since 2011. purely “domestic” use. Something to cut, screw through, etc.д. Last year the speed regulator “died”. Replaced by the Chinese analogue. It’s not working right. And the machine itself still works. No way to get to the service for the “right” regulator. My brother (bought at the same time) under intensive use for several hours a day the machine lived a year and a half. So not for the pro. But for the home is good.
I’ve bought DILD wire grinders a few times. Work for 2-3 months, then the warranty and everything around. All reviews are positive. Maybe they make it especially for me? Makita has been around for years.
You can quickly remove the cover and put it in a box. the price used to be, now it is an unrealistic price for such quality
Short brittle cord, disposable button disc stop spring, short life span
Worked exactly 2 years, in the average mode of operation without fanaticism, bought for 1100r at once flew off the button lock disk, a couple of months tore the elastic base of the wire as they say under the root, and that at a temperature.3 on the street, the wire was like glass. All the reviews are positive, Makita went for years. near the end the speed controller flew, after a week the collector began to smoke, sawed tiles in the bathroom, perhaps a consequence of moisture and dust in the air intake. So, at least sometimes vacuum your workaholic so they last longer, do not get sick and do not die)) Perhaps its price would have been worth it before the change in the dollar exchange rate. Read the Комментарии и мнения владельцев geek what he wrote that is a soft start, apparently he wrote about another angle grinder)). The only things it has are the short and brittle cord, short life span, weak disposable spring lock that does not inspire confidence upon inspection, then it was locked with a screwdriver. The plus is one is a relative quick removal of the protective casing) So a month since it broke down is useful to look at what to take and oh well this wondrous wonder has risen in price by three times. What is the money for? So my score is 1, if the price had not changed I would have given it a well-deserved 3. But it is not worth it. So I took a felisatti 115 which cost 2400r. power, reliability, speed controller, soft start smart start button. time will tell.
This is my second purchase, the first was a peorator.Previously, there were different acquisitions, Japanese, but I plucked up courage and do not regret it
Disk lock button fell off. Rigid power wire
Reliable and inexpensive angle grinder for home and garage. Many reviews are written about a tool for 2500 compared to a professional tool for 20000. So for home and garage great option.
In four years, did not identify critical shortcomings, but that the handle is thick, but now I still have a Hitachi that is much smaller
This machine bought back in the eleventh year, when I started doing construction and the first tools were almost all of Diol as then in our city it was a lot and it was cheaper than others cost, four years of operation machine has never failed, although it got a hell of a load, saw her ceramic tile, paving and facade all experienced and still works as a spare, since the fall acquired Hitachi she just lighter and cut only metal, for tile electric tile cutter is now
Not enough power to saw even a tin plate. I can stop the disk with my hand. Maybe I have a defective machine?
Easy to hold, reasonable price, easy to find spare parts.
The wire is oaky, after a while it got cracked at the base and the wire is bare. Can not keep low rpm, just stops, problematic to use for grinding. It heats up very strongly.
It burned out while sanding, either not enough power, or a problem with the electronics, in general, overheated and just burst into flames. Didn’t even take it apart, just threw it away. Has been in use for about a year.
The convenient main handle does not jump out when working with a brush (it seemed to me much more convenient than when you have to grasp the very thick body of the angle grinder).Speed controller makes it multifunctional: also suitable for sanding wood with flap discs. Nothing burns.Flip handle can be set to middle position. again convenient for grinding works.The power button lock completely eliminates accidental pressing.
This is not a disadvantage, but you should pay attention to the fact that the model and the HOUSEHOLDING working mode. Intermittent: 15 minutes work, 5 minutes pause. So if you need to work continuously for a long time, the machine will burn out. It is not designed for it. At 1 speed from start to start is not always steadily holding the rpm. Sometimes faster sometimes slower.
The grinder is very good. very comfortable and functional. I’ve been using it for about two years, mainly for grinding with petal discs. For cutting metal used less often. In other reviews, they wrote that the RPM adjustment starts at 4000 instead of zero. In my instance the low rpm is really slow. So I think there was either a defect or there is a variation of quality, which is unfortunately typical of our technique (my angle grinder is definitely Russian-made. judging by the disassembly). In general, if satisfied in the short term. intermittent operation. Very much advise, if not, it is better to look out for Bosh or Makita.
The machine is great I have more than 10 years, no problems as a poor thing cut and still alive.
Online store “Order” sells a wide range of grinders for home and workshop. Here you can buy angle grinder famous brands of domestic and foreign manufacturers Dyold, Interskol, Military, Pobeda, Makita, Vihr, Redbo, Bort, Graphite, Felisatti, Bulat, Patriot, Kölner, Stavr. According to reviews of these models are the most popular angle grinder. We offer grinders with adjustable speed, cordless angle grinder and powered from the network, household and professional.
This angle grinder Diold MSHU-0,95-01 operated by me since July 2016, that is, almost 4 years. But of course only in the summer seasons, and in the household. But, since the house had just been built and the territory was being equipped with necessary equipment, she had enough work to do.
Before buying it I had experience with only a 750 watt angle grinder. So, it is difficult to cut even profiled sheets, and constantly overheated, up to the smoke. In the end I gladly threw it away and went to the nearest store for a new one.
This time I knew exactly that I needed at least 950 watts of power, and with a speed changer. And not too expensive, for some Bosch or Makita overpay a few thousand did not want. And here Diold was the most preferred brand in this respect.
“Diold” is positioning itself as a Russian (Smolensk) manufacturer, and with its own production, allegedly with the deposit from the USSR.
Since its founding, Diffusion was widely known as the only specialized enterprise in the manufacture and production of CNC systems for lathes and machining centers. Extensive experience gained in the early ’90s allowed the company to switch to the production of household power tools on a full technological cycle.
Although some of his tools are very similar (one to one) to other brands that do not hide their products from China. Like the Kalibr, for example. So do not get too carried away here. about their own production on the official website of Diold no evidence, only words! But the presence of a normal site and ramified network of service centers gave hope for the reliability of the manufacturer and its quality control. Not just a company “Horns and hooves,” stupidly buying up cheap knockoffs in China and sticking their labels on them.
This angle grinder, popularly known as “angle grinder”, has a power of 950 watts, as evidenced by the numbers 0.95 in the title. Designed for use with cut-off wheels size 115. 125 mm. Of the distinguishing features of similar models. It has a speed regulator.
Diold has a model with a similar name, it seems MSHU-0,95-125-01, which does not have such a regulator, so do not be confused!
Economic handle with rubber inlays provides a secure and comfortable grip without slipping
That’s how it looks today, I tried to capture the complete set (cutting wheel kit was not actually there):
MSHU package.0,95-01:
Instruction manual
Addresses of the warranty repair shops
Motor brush. 2 pc
Complementary handle
Special key for fixing the nozzles. 1pc
Protective shroud. 1 pc
As for the quality of assembly and workmanship materials, everything is good. In look and feel made quality, durable plastic housing, metal motor cover in the “head” of the angle grinder of normal metal. Reasonably thick cable 2 m long.
On the base/handle bar there is a rubberized area to prevent slipping in the hands. very comfortable, I must say.
The system of switching on and off the tool:
There was some safety system at work. To pull the trigger you must first squeeze the safety lever with your thumb. Locking in the “on all the time” mode. is not provided.
And here is the speed controller with 6 positions:
RPM 0-11000 rpm
The maximum diameter of the wheel is 125 mm
The manufacturer did not indicate anywhere the number of revolutions in each position from 1 to 6, but for the home user I think it does not matter. Because you adjust it “by feel”.
Maximum speed of 11000 RPM. this is just the “limit of dreams” for a bolt cutters up to 1kW, as well as the power of 950 watts is the most optimal for domestic purposes. it is good for cutting simple metal constructions, trimming paving slabs or sanding anything. 700. 800W, as I said before, at the same maximum 11000 rpm is weak, will often overheat. And with increasing power over 950 watts the RPM is usually reduced. up to 8000-9000, but with the possibility to install circles up to 150 mm.
Т.е. Such angle grinder (over 950 W) is more for cutting concrete, maybe sawing thick boards, sanding large areas.
Angle grinding machine MSHU-0,95-01 designed for grinding and cutting work on metal and other structural and construction materials without water supply in domestic conditions by grinding / cutting / wheel.
Complete with protective shroud and additional handle:
It is the guard that determines the standard diameter of the cutting wheels. you just can’t fit more than 125 mm in diameter into it!
But you can take it off and put it in without the guard.
Although the hood itself is also not a panacea. it only partially blocks sparks and stuff. That’s why goggles and gloves are compulsory.
The handle can be moved to three possible positions. as you need it at any given moment. A sought-after function, I must say!
You can also see a red button next to them. Pressing it blocks the disc/head from turning, this is necessary to remove it from the spindle. And it is removed with a special key. it can be seen in the photo with the complete set.
To finish the description, we can finally note. The manufacturer recommends using this angle grinder in the S2-30 mode.
Short-time operation S2. when periods of constant nominal load alternate with periods of motor tripping.
In this case, the periods of operation (load) of the motor are so short that the heating temperatures of all motor parts do not reach steady-state values, and the periods of switching off the motor are so long that all motor parts have time to cool down to ambient temperature (a temperature increase of no more than 1 ºC is allowed).
The standard set duration of load periods is 10; 30; 60 and 90 min. In the notation of short-term mode the duration of the load period is specified, for example S2. 30 min.
somewhat vague, but as I understand it. You can work with a continuous load time of up to 30 min.
And also stated a life of 5 years.
During its use (almost 4 years) this angle grinder has performed tasks such as:
- Cutting metal pipes and sheets with a wall thickness of up to 5 mm, other metal fittings
- Cutting profiles for fences
- Cutting paving tiles and concrete curbs 30. 80 mm thick
- Grinding of old paint from concrete surfaces
- Trimming porcelain tile
- Trimming and sanding stone inserts in a concrete floor
- And quite a bit. board sawing.
Not to be unfounded, for example, photos of the remnants of what was cut by the angle grinder (not all):
You can use special nozzles to work.
This is my kit from last season’s save:
Yes, that’s right, the biggest circular saw. diamond with 150 mm diameter, I had to use without cover
I would like to mention the pluses:
- For domestic use in a private home with its household. Just the right “angle grinder”. 950 Watt, with a nominal lap diameter of 125 m! No more, no less, you can trust me.
- Never overheats!
- Doesn’t vibrate while working
- Perfectly cuts and grinds all mentioned materials.
- Reliability. Not a single failure remark so far. By the way, the spare brushes supplied have still not been needed. According to the instructions, they need to be replaced when there is a spark, which has not yet been observed. Here is a completely clean, non-burned socket for brushes:
Dnipro M GS-140SE angle grinder �� Review | With my own eyes
It is also recommended to check and lubricate the gearbox, I have not tried that yet, but will have to see.
- The presence of a speed regulator. Perhaps it is not critical (its absence), but I noticed. It is good to cut metal at maximum rpm, paving tiles and curbs at lower rpm. When sanding various surfaces, you set the speed also “by feel”. Besides, if you install a heavy diamond wheel of not the nominal diameter, but 150, it is better to set the speed less. to avoid trivial overload.
In general, mode 1 and 2 are hardly used.
- Simple fuse to prevent accidental start-up, as well as for automatic shutdown in case of tool pulling out of hands. It happens that the wheel gets caught on something and the angle grinder jerks sharply in your hand! If you let go of the trigger with your fingers, the tool shuts off.
- Normal power cord with plug. in the same way, so far no problems with it.
- And a comfortable grip, of course, plus three positions for an additional handle. In addition, the tool is moderately large. Unlike the smaller short ones, it is more convenient to work with from a safety point of view.
- pretty informative instruction.
There is not much to note about the disadvantages. I’ll limit myself to the classic “None identified.”.
angle grinder Diold MSHU-0.95-01. An excellent and optimal choice for a private home. Universal in use, reliable, and pleasantly priced in comparison with name-brands. They are now on sale, priced around 2400, so the choice to RECOMMEND.
Looking for positive and negative reviews of the angle grinder DIOLD MSHU-0,95-01, 950 W, 125 mm?
From 11 sources we have collected 26 negative, negative and positive reviews.
We show all the advantages and disadvantages of angle grinder DSHOLD MSHU-0,95-01, 950 W, 125 mm revealed in the use of users. We do not hide anything and put all the positive and negative honest customer reviews about angle grinder DIOLD MSHU-0,95-01, 950 W, 125 mm, as well as offer alternative products similar. Is it worth buying. the decision is yours alone!
angle grinder DIOLD MSHU-0,95-125, 950 W, 125 mm
Looking for positive and negative reviews of angle grinder DIOLD MSHU-0,95-125, 950 W, 125 mm?
We collected 29 negative, negative and positive reviews from 11 sources.
We will show you all the advantages and disadvantages of angle grinder DIOLD MSHU-0,95-125, 950 W, 125 mm revealed in the use of users. We don’t hide anything and we post all positive and negative honest reviews about DIOLD angle grinder MSHU-0,95-125, 950W, 125 mm, as well as alternatives to analogue products. Should I buy it? the decision is only up to you!