Chainsaw Chain Will Not Move? Try this First- Quick Tip
The chain is stretched
If the chain is used incorrectly or for a long time, it can be very stretched. This is due to the fact that the metal can deform over time. Too much wear and tear becomes the reason why you have to purchase a new version, but it is possible to use the old one for a short period. Rapid stretching can be avoided only if the recommendations for use are followed. To carry out the work you need:
It is not difficult to put on a stretched version, but there are quite a few problems with restoration, since the metal is characterized by increased strength. In this case, the main elements are fastened with rivets. The work is carried out as follows:
- The product is fastened in pieces.
- If the work is carried out using an angle grinder, then there is a possibility that the surface will be damaged, since this tool is difficult to control.
- After crushing, rivets are knocked out. Do not throw it away as it can be reused.
- Chain manufacturers do not issue spare parts that are required for maintenance.
- You can make a rivet with your own hands, but the work is quite difficult.
- The product is divided into two parts. It should be borne in mind that the number of guides and the distance between them must remain unchanged.
When solving a problem with a long length, do not forget that too short a chain can no longer be pulled. In addition, it is not recommended to apply oil to the saw chain.
Trouble with a leading star
Sometimes chain slack is due to drive sprocket problems. The most common situation is when it is poorly secured. Step-by-step algorithm to twist the asterisk:
- Remove the engine cover.
- Remove the air filter and unscrew the candle, putting in its place a special stopper to fix the piston in an immovable position.
- Using an angle grinder wrench, turn the clutch disc clockwise to the highest position. Check the tightness of the sprocket, adjust its position.
Figure 3. the driving star on the chainsaw
After tightening, reassemble the chainsaw, be sure to put on the protective cover. When assembling, check that the chain fits snugly on the bar.
How to put the chain on a chainsaw correctly: direction
When considering how to correctly put the chain on the chainsaw, we note that the modern version of the tool has a special setting wheel. Due to it, the procedure is greatly simplified. Among its features, we note the following points:
- Considering how to properly put the chain on the chainsaw, we note that first you need to prepare a flat surface. This eliminates the possibility of damage to the tool. After that, the main part of the tool, the bar and the chain are laid out separately.
- The next step is to remove the protection that is designed to protect the sprocket. In most cases, it is fixed with a conventional wing nut.
- On the tire, the sprocket turns to the right until it stops. It is in this position that the tool is installed.
- Then the chain is gradually superimposed on the fixing element. A fairly common question can be called which side this element is put on. Installation starts at the top, the chain is rotated so that the bar is on top. Such operations should be carried out exclusively with thick gloves that can withstand the impact of the cutting edge. The cutter on the end face must be facing forward.
- Both elements are worn on an asterisk.
- The next step is to reattach the chain sprocket cover. It is important to make sure that the pins line up with the holes. Improper fixation may cause rattling or other problems.
- It is necessary to ensure that the guides fall into a special chute.
- The state of the chain is checked visually after it is fixed.
The next step is to directly check to see if the chain has been overtightened. To do this, release the chain brake and pull it along the mowing line of movement. The check is carried out exclusively with special gloves.
In general, we can say that the procedure under consideration is quite simple to execute and does not require special tools to carry it out. However, not all chainsaws are as easy to maintain as stated above.
How to put a chain on a chainsaw correctly: instructions, recommendations, basic methods
The chain is an important element in the construction of a chainsaw. It is she who has the greatest load during work, so high-quality and systemic care is required. When using any model, it is important to know how to put on the chain correctly, to monitor its tension. If it is not secured correctly, there is a risk of stretching and coming out of the grooves. Reduced saw performance and increased risk of injury at high power.
There are many models of chainsaw chains on the market now. First you need to know which standard size is right for your chainsaw and not make a mistake in buying. The second step is to properly install it on the chainsaw. This is a somewhat laborious process, but if you know how to put on and adjust the chain to the saw bar yourself, then the happy owner should not have any problems. We tried to describe in detail the process of installing a saw blade on a chainsaw.
We hope that after reading this article, you will succeed the first time. But in order to minimize the occurrence of problems with the chainsaw and chain in the future, do not forget 3 basic rules:
Texas Chainsaw Massacre Ending
- If the chain is worn out and sagged, replace it with a new one;
- If vibration appears during sawing and the cut is bad. watch the chain tension on the chainsaw;
- Never use saw blades that are defective or repaired by dubious specialists, your health and those of those who are nearby are much more important than a little savings on buying a new and reliable chain.
Poorly fixed drive sprocket
Quite widespread is the variant when the leading sprocket is poorly fixed. It often detaches itself during operation. The solution to this problem is carried out as follows:
- The protective cover of the engine and spark plugs are removed, after which the air filter is removed.
- The next step is to remove the spark plug, which requires a special wrench.
- A special plug allows you to fix the piston in the desired position.
- The clutch plate is turned with a special key until the position of the piston, which should be located on top, is changed.
Then you can fix the sprocket in the correct position and solve the problem in question. The specified information indicates that such work is quite problematic, it is often carried out by organizations servicing chainsaws.
Chain tension
To check the tension, you must first release the brake. Then pull off the chain in the middle of the headset, normally the shanks should not protrude more than 2/3 of the height. It is recommended to scroll it manually. do not jam and slip too fast. If necessary, tighten the nut on the protective cap.
Figure 5. Checking the chain tension
Installing and checking the tension of the chain on the bar is an important process in the operation of any chainsaw. The work is easy to do on your own. Regular tool maintenance avoids injury and reduced productivity, even when working with dense woods.
Advantages of making a chain set
The chain and the bar are included in the list of interchangeable equipment, so the sawyer, depending on the peculiarities of the work, can use several sets of different lengths and productivity. Average service life of wear-resistant branded tires allows the service life of three saw chains.
The cutting edges of the saw chain links need to be sharpened periodically. The indisputable advantages of using a set of several chains are uniform wear of the drive sprocket and good compatibility with the chains included in the additional set.
The chain is stretched
If the chain is used incorrectly or for a long time, it can be very stretched. This is due to the fact that the metal can deform over time. Too much wear and tear becomes the reason why you have to purchase a new version, but it is possible to use the old one for a short period. Rapid stretching can be avoided only if the recommendations for use are followed. To carry out the work you need:
It is not difficult to put on a stretched version, but there are quite a few problems with restoration, since the metal is characterized by increased strength. In this case, the main elements are fastened with rivets. The work is carried out as follows:
- The product is fastened in pieces.
- If the work is carried out using an angle grinder, then there is a possibility that the surface will be damaged, since this tool is difficult to control.
- After crushing, rivets are knocked out. Do not throw it away as it can be reused.
- Chain manufacturers do not issue spare parts that are required for maintenance.
- You can make a rivet with your own hands, but the work is quite difficult.
- The product is divided into two parts. It should be borne in mind that the number of guides and the distance between them must remain unchanged.
When solving a problem with a long length, do not forget that too short a chain can no longer be pulled. In addition, it is not recommended to apply oil to the saw chain.
Bus problems
Today, the problem associated with an unreliable fixation of the tire is often encountered. It is characterized by the following features:
- The body with the guide element is fixed with a bolt.
- The connection is provided by two plates, one of which is located on the body, the second on the one, which is designed to guide the chain at the time of operation.
- The drive sprocket and the tire support are protected by a special casing, which eliminates the possibility of damage to the main elements.
- When the locking bolts are loosened, the structural element in question begins to move and vibrate at the time of operation. You can solve this problem by tightening the fasteners.
Other defects simply cannot be solved. In most cases, defects become the reason why you have to purchase a tire and replace it.
How to put the chain on a chainsaw correctly: direction
When considering how to correctly put the chain on the chainsaw, we note that the modern version of the tool has a special setting wheel. Due to it, the procedure is greatly simplified. Among its features, we note the following points:
- Considering how to properly put the chain on the chainsaw, we note that first you need to prepare a flat surface. This eliminates the possibility of damage to the tool. After that, the main part of the tool, the bar and the chain are laid out separately.
- The next step is to remove the protection that is designed to protect the sprocket. In most cases, it is fixed with a conventional wing nut.
- On the tire, the sprocket turns to the right until it stops. It is in this position that the tool is installed.
- Then the chain is gradually superimposed on the fixing element. A fairly common question can be called which side this element is put on. Installation starts at the top, the chain is rotated so that the bar is on top. Such operations should be carried out exclusively with thick gloves that can withstand the impact of the cutting edge. The cutter on the end face must be facing forward.
- Both elements are worn on an asterisk.
- The next step is to reattach the chain sprocket cover. It is important to make sure that the pins line up with the holes. Improper fixation may cause rattling or other problems.
- It is necessary to ensure that the guides fall into a special chute.
- The state of the chain is checked visually after it is fixed.
The next step is to directly check to see if the chain has been overtightened. To do this, release the chain brake and pull it along the mowing line of movement. The check is carried out exclusively with special gloves.
In general, we can say that the procedure under consideration is quite simple to execute and does not require special tools to carry it out. However, not all chainsaws are as easy to maintain as stated above.
- Loosen the screws securing the sprocket protection cover, usually it is tightened with a wing nut.
- Turn the tensioning sprocket to the right until it stops.
- Place links on the headset starting at the top. Drink so that they fall into the corresponding grooves.
- Fasten back the chain sprocket mount, tighten the nut. The guides must fall into a special chute.
- Release the chain brake, pull the chain along the mowing line to check the tension. Tighten the tensioner lever if necessary.
Figure 4. Installing the chain on the chainsaw
The setting wheel should turn freely after installing the chainsaw chain. At the end of the work, it is imperative to lubricate all moving parts of the tool to avoid rapid wear.
Important! The headset should only be installed with heavy protective gloves. This will protect you from injury and cuts from the sharp edges of the cutting edge of the teeth.