Champion lawn mower swim turns and stalls. Diagnosis of the filters of the lawn mower

Why does a trimmer for grass float. ECHO trimmer does not develop turnover reason. Problems with ignition candles

Perhaps more and more a widespread complaint associated with gasoline trimmers sounds like this: “The lawn mower stalls”.

Naturally, a rather harsh fault may be a prerequisite for this. Why does a trimmer for grass stall when you press the gas? The reasons for stopping a trimmer for grass at high and idle speeds, when heated or opened by an air damper. Chinese chainsaw.Repair and trimmer for STIHL grass stalls when it does not start. Gasoline, two.stroke: who knows why and what to do. Why is not gaining momentum. But in most cases, the situation is even easier than it seems to be the 1st gaze.

In order to cope with such an inconsistent, first, try to deal with its causes without the help of others, because, having found out the reason, it’s even easier to fight with the inconsistency, and from time to time it is even self.destructive.

In fact, circumstances, this is when the lawn mower stalls at high speeds. There are quite a lot of these circumstances.

Another is the presence of defects in the power system.

In this case, the lawn mower will stall at idle. Or even the engine is suitable and it doesn’t matter, the trimmer for the grass stalls because of why it stalls. The gasoline trimmer for the grass is poorly started. For 1 mm I do not think that a trimmer for grass cannot understand why it does not gain momentum. And “Husqvarna stalls and does not start. Dilems with the power system may lead to a drainage or incorrect carburetor adjustment.

Technical characteristics of the Stihl FS38

The lawn mower will become a gas when adding.trimmer for grass does not pull.Trimmer for grass is lost at load.

Vibrations that take place in the process of operation of the lawn mower can lead to a reservoir.

Incorrect adjustment of the lawn mower can be fixed by simply adjusting it in accordance with the requirements specified in the operating instructions.

In addition, sometimes gasoline trimmers for grass can stall due to the fact that the valve located in the gas tank cover just clogged or stick.

To find out, try using a braid by loosening the gas tank cover.

If in this mode the device works properly, clean the valve.

In this article we will consider the problem why the lawn mower stalls and how to deal with this problem.

Even very good motorcycles may have problems with the launch. For example, it starts and stalls. Most likely, this indicates problems with filters. air or fuel. If it stalls at idle, then, most likely, the motorcosa has problems with the carburetor, which is too fast overheated and no longer copes with the formation of a qualitatively air fuel mixture.

If a trimmer for grass stalls when you press gas, t.e., когда двигатель начинает работать на больших оборотах, то это свидетельствует о проблемах с карбюратором или с топливным фильтром.

Motokos with an air filter will be evidenced by the fact that it ceases to work when opening an air damper.

Note that the Well Part online store offers you for the widest assortment and at the best prices.

The lawn mower stalls, what to do

A newcomer and experienced owner may face the problem of the stalled motorcycle, the situation arises with those who have been in use and completely new braids, and which ones we will understand this article. So, the tool can stall under load, immediately after starting, that is, it starts and stalls, when heated by the entire mechanism, at high speeds, or does not even gain momentum and stalls. In all these cases, in fact, the same systems, elements, nodes are involved, but the breakdown or malfunction of each of them, more precisely, the nuances, cause an individual above situation. The answer to the question of each user: why the lawn mower stalls, you will get only on our website in the section of news articles.

To completely deal with your individual situation. carefully read the signs and related nuances at the time the braid for the grass stalls, and then it will be easier for you to find a way out and quickly solve the problem. If you need certain spare parts for the lawn mower to buy, then do this in bulk, and the best store of gas instruments in Ukraine will allow retail, “Benzo Zip”.

• Why stalls the lawn mower: reasons and solutions
• What to do if the lawn mower stalls when you press the gas
• Why is the lawn mower stall at idle

Why stalls the lawn mower: reasons and solutions

The reason why your tool abruptly stops working, namely the engine does not gain revolutions, breaks them off, or “stalls” in popularity, there may be more than one. Often this is to blame not only the engine itself, but also the adjacent systems, unit nodes, completely different details related to the preparation of the fuel-air mixture, its quality, transportation to the tool of the tool. Consider the most typical situations:

• He is not gaining momentum. The engine drive mechanics may be damaged or there were problems with the carburetor, but the main reason should be considered clogging of the air filter. To change the situation, it must be removed, cleaned, and if it is no longer subject to the latter, then change for a new one, promptly making an order on our website. Also, there will not be a turn of the braid for grass, if the cable from the carburetor constantly flies. disassemble the unit and firmly fix it, or buy a new one if cracks are found on the element, other types of deformations.
• At high speeds. The lid on the gas tank is clogged. it needs to be cleaned or new. often the reason is a sipped carb. We submit information on the correct adjustment of all screws in information articles. Check the quality of the fuel hose and change it to a new one if necessary.
• When heated. It occurs in moments when the fuel in the carburetor literally boils. It can also appear in the options if the carba damper is more rare, rotary type (not disk). The only option would be to replace the carburetor with a new. There is another option for a broken wire or ignition coil. In this case, change the element of the latter.
• Starts and stalls (immediately after launch). Solved or incorrectly adjusted carburetor is the main reason for this situation. Calm vibration will indicate an uneven supply of fuel, and competent adjustment of the node will help to correct the situation.

We hope you found the right answer to the question: why the lawn mower stalls, and all the proposed catalog details today, as always, are at your service. You need a piston trimmer for grass, a new carburetor, or the elements accompanying the operation of these systems. you will find everything in the open spaces of the Benzo SIP store.

What to do if the lawn mower stalls when you press the gas

Most often during the periods when the lawn mower stalls when the gas is added, the cause will be the air damper, more precisely, its condition: it clogged. Structurally, the part is located in the place where the resulting fuel is sprayed behind it, and, accordingly, the product collects all inclusions in low.quality gasoline. To eliminate the problem, you just need to clean it. The same situation can occur with a filter clogged, but it is eliminated similarly. Total, we specify the reasons for which the tool is led to the gas to the stalled state:

• a clogged air damper;
• The clogged filter is fuel, and when you give gas, this is especially noticeable;
• the air of the crankshaft shaft occurs;
• damaged gasket between the cylinder and the carb.

When you cleared, washed and blowing the elements, but again the lawn mower stall when you press the gas-replace them with new ones, check the quality of the fuel, as well as the literacy of the proportions of the cooked mixture. When opening the air damper, the tool will stall for the following reasons:

• Dosage carburetor.
• The appearance of cracks on the fuel hose caused air leaks.
• The occurrence of problems with the oil seals.

In the process, situations arise when the lawn mower at high speeds is subject to a similar sharp stop. It occurs for the following reasons:

• due to problems with the circulation of the fuel mixture;
• with air leaks;
• The fuel intake hose is poorly connected or cracked and cannot be used;
• stab or clogged the valve of the cover of the gasoline tank;
• The carburetor was resolved.

In most cases, nevertheless, the cause will be a carburetor and related filter, hoses. If you need cutting gear or trimmer heads, then our site will also offer them to buy them with gasoline tools and components for them.

Why is the lawn mower stall at idle

Users have repeatedly ask about stopping the braids for the grass “on hot”, that is, when the mechanism started, worked a little, and then took it. and stopped, stalled. The reasons for this situation are the following:

• problems with the carburetor damper;
• Gasoline in a carbe can even boil;
• If the ignition is damaged, then the trimmer for the grass will also heat up and stall.

In each of the situations, check the details for strength, and if they have already outlined their own, order new ones from specialists. We will call one of the most popular situations: the lawn mower stalls at idle. This happens for reasons:

Do.it.yourself cultivators repair

If your cultivator “swim” turns, or it sneezes and does not develop the necessary power, try all points from our table, maybe you can eliminate the malfunction with your own hands. If this did not help, you can contact the specialists of our service center details on the page repair of cultivators.

The cultivator does not start

Check if all the actions necessary for removing the ignition lock are made: the lock is raised (lowered), whether the lock cable is working

Check the presence of gasoline in the gas tank, fill in if necessary

Press the tip to the candle and fix it properly

The candle is defective, the electrode was polluted or burned

Replace or clean the candle, set the gap between the electrodes by a size of 0.75 mm

Unstable engine speed, black smoke during operation

The candle is defective, the electrode was polluted or burned

Replace or clean the candle, set the gap between the electrodes by a size of 0.75 mm

Work is carried out with a closed air damper

Check whether the carburetor air damper is open when working.

Oil entering the release system of curtain gases

If white smoke appeared unexpectedly and immediately after the cultivator tilt more than 60%, then perhaps the oil got into the system of release of curtain gases as a result of the inclination. It is necessary to check the oil level in the engine crankcase, with a lack. add the oil to the required level. Start the engine and give excess oil to develop. After 5 minutes of operation, it is necessary to drown out the engine, give the oil to stand up and check the oil level again, if it remains unchanged, then start the engine again and develop all the oil accumulated in the emission system. After 10-15 minutes, white smoke should disappear. If this does not happen, then you need to contact the service center for diagnosis and eliminate the malfunction

Exceeded oil level in the engine crankcase

Replace the oil, replace or clean the candle, set the gap between the electrodes by a size of 0.75 mm

The cultivator does not move forward, backward. Cutters are not turned on.

Check, adjust the tension of the cables

Check, adjust the tension of the cables or replace the belts

The liquid got into the ignition system

Unscrew the candle and try to pull the starter’s rope without a candle

The cultivator stalls when the milling

Check if there is an extraneous subject in the field of milling

Frequent breakdowns of the lawn mower: review and solution to problems

Using a gasoline lawn mowing for cutting the lawn, you need to be careful and follow the operating rules exactly. After completing the work, the device must be cleaned, since even a small clogging can block a moving mechanism. If frequent breakdowns of the lawn mower occur: the review and solution of the problems can be found by reading this article.

The reasons

The main reason for the malfunction in the work of the mechanism can be called the application for other purposes. Possessing knowledge about the principle of work and mechanisms of garden technology, it is possible to eliminate problems with your own hands. But it is still better to contact a specialist, especially with serious breakdowns. Among the breakdowns that are most often found, the following can be distinguished:

• Unusual garden technique noise. This is usually due to weakening the bolts or poor fixing the body. You need to carefully examine all the nodes and twist the bolts. If the noise resembles a whistle, most likely an extraneous subject fell into the mechanism. It is necessary to turn off the mechanism and remove an extraneous object;
• The case is unnaturally shaking when working. Most likely, the reason is the malfunction of the cutting element that needs to be replaced;
• The lawn mower will not start. First you need to check the presence of a sufficient amount of gasoline in the tank. If everything is in order with this, and the engine does not work, a faulty ignition candle may be a possible cause. In other cases, it is recommended to consult a specialist, since it will not be easy to repair a mower on your own;
• The engine does not gain momentum and immediately stalls. The reason may be the jamming of the mechanism. If this happens due to lack of lubrication, you need to pour oil into the crankcase and put the mechanism into motion;
• The uneven surface of the lawn. This means that the cutting elements are dull and the grass is poorly cut off. It is necessary to sharpen the knives, and it is better to replace them with new ones;
• The lawn mower does not go or the movement is difficult. First of all, you should check whether the height of the mowing is selected correctly.

All of the listed malfunctions can be eliminated independently without addressing specialists.

Service

It is worth listing several techniques, thanks to which you can keep your garden equipment in excellent condition and minimize the need for special service.

• If the lawn mower has not worked for a long time, it is necessary to drain the stagnant gasoline, as shown in the photo;
• Gently pour high.quality gasoline into an empty tank with a watering can;
• If necessary, add the primer of the swing of the carburetor and set the maximum speed.

The lawn mower will not start

• If the engine does not start, it is necessary to check the position of the air damper. If the air temperature exceeds 30 ° C must set the average position;
• With prolonged operation of the equipment, it is necessary to take breaks for 5 minutes to avoid overheating of the engine;
• It is necessary to check if the gasoline came to the spark plug;
• If gasoline stagnated in the tank, it is worth changing it to a new one;
• It is necessary to check if the filter passes the air well, with the need to rinse it;
• You can pump up fuel into a carburetor using a primer.

If the braid does not go, you need to check the drive belt. perhaps it is worn out and requires replacement.

The lawn mower is not gaining momentum

The reason may be such malfunctions:

• It is necessary to inspect the silencer. perhaps it is clogged;
• The grass was wound on the shaft and from this does not twist the knife, as shown in the photo;
• Rust on the mechanism and details;

If the mower does not work at full power, it is necessary to disassemble and clean the mechanism.

The lawn mower does not collect grass

The reason for this may be faulty or stupid knives. In order to avoid such a situation, you need to install new knives every season. You can do with the sharpening of knives at an angle of 30 °.

When hidden, it is necessary to protect yourself with special glasses and protective gloves. After sharpening, you need to test the balancing of the knives.

If a cylindrical mower does not collect grass, then it is better to sharpen knives in the service center. But you can purchase a sharpening device in the store and sharpen yourself, as shown in the video.

To do this, you need to bring the cylinder of the turned off the braid to the position with the maximum interval between the blades. Then the abrasive strip is glued to the sharpening device, and the cylinder is transferred to the position in which the blades relate to the abrasive.

The mitch needs to be turned on for short intervals of time until the blades become sharp.

The knives are incorrectly adjusted

This can be seen on the uneven surface of the lawn. Before adjustment, it is necessary to turn off the lawn mower from the network and put on protective gloves.

The lawn mower does not work on idle

A gasoline braid for grass is necessary for owners of personal plots, lawns, and when a trimmer for grass dies at one moment, the work on cleaning the site from the grass stops.

The device itself is essentially a rather complex mechanism, since there are many different circumstances to fail it to fail. The most common problems are contained in the operational annotation.

Know the prerequisites for why the trimmer for the grass is worth it, you need to repair the device without outside help.

Problems with a bushrease due to the fact that this device is not launched, specially classified by service specialists. They identify malfunctions with the following components:

• the engine in which it can wear out, in other words, the piston and bearings fail, the crack of the engine crankcase;
• Fuel supply system, while you score a filter or perform tasks with a carburetor;
• mechanical damage to wires, tubes, hoses;
• The ignition circuit.

To correctly find the knot where the failure occurred, it is necessary to check the circumstances in which the trimmer for the grass stops.

If the brush stops when you press the gas, the following prerequisites occur.

• A more common version of a carbohydrate adjustment error, which occurs with significant loads on the drive, after a long downtime of the mechanism, in other words, when it is used in a sluggish environment.
• The clogging of the fuel valve that deprives its relaxation, and as a result, gasoline begins to flow normally through the system.
• Weakening and lowering the cable in the carburetor. It also occurs an extension cord extension shortly before its breakdown caused by a significant load.
• Clogged breathing tube (check valve), for this reason the fuel does not get into the tank.

The engine starts and dies. Background

If the problem is related to the carburetor node, this can be determined by the vibration of the brush.

When the braid lingers at high speeds, this is due to the following problems:

• clogging or gluing the valve located on the gas tank lid;
• the carburetor is not leveled under the influence of vibrations arising during the operation of the mechanism;
• difficulties with fuel circulation;
• air leak;
• The hose created to suck fuel cracked or weakened.

Carburetor settings, focusing on the operational annotation to the trimmer. For the option, it is often enough to loosen the tightening of the body. If there are problems with the circulation of the fuel consistency, it can gradually get into the carburetor. After its development, the engine turns off at high speeds.

General reasons for stopping a trimmer for the grass at idle:

• a decrease in the speed of the gear rotation during its heating, which is a consequence of the use of inappropriate fuel consistency;
• clogging of the throttle;

• air entering the system;
• There is not enough fuel to work with a brush.

If there is a problem with the carburetor, the equipment will stop during the “cold” and “hot” launch.

The block may stop immediately after starting, if the carburetor is incorrectly adjusted or adjusted incorrectly. This causes uneven fuel supply. As a result, the device begins to vibrate clearly. To solve the problem, the carburetor is regulated by affecting the explanation of the mechanism.

Gasoline warms up and delayed (change of the piston group). Repair Kustorez, a new piston group

In addition, the engine stops when the valve clogged, fuel supply. In this case, it is quite easy to remove it. If the lawn mower at first worked, but then immediately stopped, fuel with some difficulty enters the carburetor unit. The weakening of the valve helps to solve the problem that provides free circulation of the consistency in the system.

You can also cause a stop. Air absorption in the presence of mechanical damage to the hose (openings, cracks), which fuel fuel. Then you need to add speed to the drive to quickly remove air bubbles with the resolution of accounting (software).

Motocosis often stops when heated. At the same time, it starts, works “jerks” and stops evenly. This process occurs when the gas in the carburetor boils or there is a swivel damper, not a disc. In the latter case, the element changes.

It happens that a trimmer for grass heats up if the ignition wire or coil is damaged. For the proper operation of the device, replace the parts.

It happens that the device opens when the air damper opens, it works normally at idle. This is due to air leaks in the system caused by the presence of the fuel hose crack or problems with oil. Also, the carburetor dosage system may not work, here the bureau will stop after the opening of the damper.

Our client still has probable prerequisites that the brush stops, and the methods of eliminating them are contained in the next video

There are many circumstances to stop the lawn mower, but for the most part there are problems with its carburetor. They come in any form. The most problematic option. when there is a strong breakdown, and it will be useful to get new parts or replace the bush.

In order for the trimmer for the grass to work normally for more than one year, it is necessary to comply with the requirements of the operational annotation. It is necessary to refuel the unit with the appropriate fuel consistency, the device should operate with a moderate load.

The lawn mower stops after a few minutes

Repair of lawn mowers is carried out taking into account the mechanism of work and the background of the unit malignant. Most often, the device fails 3-4 years after active use.

Repair of the lawn mower is necessary in the following cases:

The causes of the malfunction

The prerequisites for the failure of the lawn mower:

In the first case, you will need to change the case, handles, knives and wheels for lawn mowers. When the knives are blocked, the device stops mechanically. This error is associated with an attempt to mow solid or high grass. The repair of the mower is to free the cylinder from the stuck grass and scroll it in a different direction.

Why the lawn mower is not started, the reasons

Figure out what has brought the device into a faulty state by disassembled it. You need to do this carefully and carefully, inside there are many small details that are easy to break. There are 2 types of damage: mechanical, electrical. Consider the most popular reasons why the lawn mower does not start and stalls:

• Carburetor failed;
• bolt compounds were shaken;
• Motor breakdown;
• jam the moving components of the mechanism (crankshaft, piston);
• Blocking a cutting tool (cylinder) by an alien object. branches, sticks, hard grass, stones, etc.;
• The oil supply and fuel supply system is disturbed;
• The light of the ignition failed;
• stretched out, the belt broke;
• a small or too large gap between the details inside the structure;
• faulty device switch;
• Dirty fuel hose, ventilation grilles;
• Cunnered air filter.

With prolonged use of a gasoline lawn mower without a break, the device stalls. Why the lawn mower stalls and does not start hot? The engine is overstrain. It is better to lay off the mowing, let the lawn mower be standing, after it has stalled, most likely the reason lies in the overheating of the device.

In some cases, this is a temporary phenomenon after the motor has cooled down, the equipment can work again. But still, you should not go out for hours. With active use, the life of the equipment is reduced. On average, repair is required 4 years after the purchase of goods.

Symptoms of problems

The first thing the user may notice is a deterioration as the operation of the device. The grass is not molested evenly, there are missing places on the lawn. This is because the engine begins to junk, its power decreases. TOP-5 symptoms indicating a problem:

• Enhanced vibrations of the device.
• Increased noise when working.
• The lawn mower starts and stalls.
• The device is disconnected independently.
• The car whistles.

The main 3 reasons why the lawn mower stalls. improper operation, overload, long.term work (engine overheating). The system is cooled, thanks to the air filter, it should be checked every time when using garden technology. What to do so that the lawn mower does not stall. before turning on the device, check the presence of gasoline in the tank, is there any oil. It is recommended to clean the filter after each mowing.

Elimination of malfunctions in professionals

One hundred has not only a car, but also a garden-technique. Typically, the service center is converted with a malfunction of the piston and carburetor of the device. Why and why the gasoline lawn mower does not start in these cases determine the master:

• Damage to the integrity of the device or individual parts. a tonometer, by pressure, find the affected area, seal it.
• Clogging of channels, nozzles. elements are blown by air, cleaning fluids are used.
• Worn pistons, laying. replace the assembly parts.

Fault prevention

The rules of operation of garden equipment are not difficult if you adhere to these points the device lasts longer than the estimated deadline:

• Always use high.quality fuel mixture.
• Do not work in the rain.
• Pump up fuel into a carburetor primer.
• Pour the right amount of gasoline into the tank, eliminate fuel enters the engine.
• Mow with interruptions. The device should be given for some time to cool and rest. The gasoline lawn mower is often not started on a hot.
• Clean the setting of the structure, only after the engine has cooled. Clean: knives, channels, filters, container. It is advisable to do this with the use of special cleaning solutions. this is how it will be possible to avoid corrosion of metal elements.
• Store the device in dry, warm room, eliminate moisture.
• During the work, do not put pressure on the device, make smooth movements forward, advance along the site. Chaotic movements back and forth-wear out the unit faster.
• If the device is unused for a long time, you need to replace the fuel with a new. Gasoline stagnates in the system, does not allow the unit to function normally.

It should be noted that with the onset of cold weather, the car is removed as unnecessary, it is recommended to drain all gasoline for this period (it is explosive with stagnation). How to properly prepare the lawn mower for work after winter: inspect the entire case for defects, drain and replace gasoline, check the presence of oil, start the car with a ajar or closed air damper.

Why stall the engine of a trimmer for grass when recruiting

The most popular with summer residents, gardeners and gardeners trimmers for grass are equipped with two.stroke engines operating on gasoline. In recent years, part of the manufacturers have been promoting motorcycles and leaflets based on four.stroke engines in the market, but they have not yet gained the popularity that two.stroke. They are more difficult in the device, more demanding on the mode of operation, purity of fuel, oil quality. Also, four.stroke engines are more in weight and more slowly gaining momentum.

During the operation of trimmers on the basis of two.stroke engines, a number of characteristic malfunctions arise related to the features of the design of the engines. With all the perfection of the Husqvarna or Echo engines, even they occasionally “acting up”. The budget models of motorcycle assembled in China, problems arise more often. This is due to both the lower quality of materials and the assembly level. The most characteristic malfunction is a poor launch from a “hot” state and “subsidence” of revolutions at a slight load. But sometimes a trimmer for grass stalls with a sharp press on the throttle key. Why does this happen?

The reasons for the breakdown

For all the apparent simplicity, the lawn mower is a well.thought.out and balanced tool in which each part is in its place. If everything is regular, the engine from the cold state should start after the first starter jerk. Depending on the model, first you need to swing the fuel mixture by pressing the transparent button on the carburetor. In a number of modern fuel pumping models, it is not required.

You also need to transfer the lever on the carburetor to the extreme position to close the air damper. In some models of Husqvarna and other manufacturers, the shuttle of the damper is carried out by turning a special regulator. After that, you need to turn on the ignition on the handle and energetically pull the starter’s cord, while pressing the gas key to about half.

The engine should start after the first jerk, but can earn after 3. 4 movements. This cannot be considered a breakdown. it all depends on the production of the motor, the quality of the fuel mixture, temperature and humidity and other factors. Two.stroke engines have their own character, to find out why they are not launched from the first, but from the fourth time, it is difficult even for professional mechanics.

If the engine confidently launched and earned, but the trimmer for the grass stalls when pressing the gas, then you forgot to transfer the carburetor lever to the position of the open or partially open air damper. Usually. this is the movement of the lever down. It may happen that the most stable the lawn mower works with a not fully opened damper. If you have used the trimmer for more than one season, so it will be. When the lever of the damper is transferred to the extreme lower position, the fuel mixture can become too impoverished and the trimmer for the grass stalls when you give gas.

This feature is not considered a malfunction. you just need to check the work of the trimmer for grass in different modes and try to use the optimal one in work. But there are other reasons why the lawn mower can stall at any stage, immediately after starting or during operation.

Other possible reasons

If, with a sharp addition of revolutions, the engine stalls, as if zabulae, then the reason may be:

• Carburetor adjustment failure. This happens after prolonged downtime or after excessive loads, for example, natives in hot weather or in conditions of strong dustiness.
• Clogging valve on the tank cover. Eliminated by replacing the lid or cleaning valve.
• Weakening of the cable of the carburetor regulator drive.
• Stretching of the fuel hose.
• Depressurization of traffic jams on the tank, which includes hoses.
• The clogging of the sapun.

When looking for the reasons why the trimmer stalls for the grass when trying to increase speed, other reasons may appear, for example, associated with the ignition coil and candle. If the fuel mixture is not prepared according to the rules using cheap oil or poor.quality gasoline, the proportions are not observed, or the mixture cooked a month ago, then the engine can also stall when trying to add gas.

How the real reason is determined

In the case when the carburetor is responsible for stopping the engine, a sudden stop is accompanied by a nearby symptoms. Most often, this is the appearance of tangible vibrations in all operating modes. Carburetor adjustment is carried out using two screws. idle control and fuel supply. In which direction to rotate them should be written in the operating instructions. If independent adjustment has not helped, contact the service center or buy a new carburetor.

If you have a lawn mower of a professional or semi-professional class, for example, the same echo or al-ko. then the carburetor resource is approximately equal to the durability of the motor and there is no need to buy a new one. It is enough to seek help in adjustment to a knowledgeable specialist. Motokos type Champion has a slightly lower carburetor resource, it may happen that adjustments will not help. Carburetors of two.stroke engines in the repair are complex, so it is better to order a new.

After making sure that the carburetor works fine, but the lawn mower still stalls, try to loosen the gas tank cover. If the engine operating mode has changed, it means that the lid valve is clogged or clogged. Practice shows that it is useless to clean it. It is better to buy a new cover, it costs a little, and it will last at least 2. 3 seasons.

Along the way, check the tightness of the gas pipeline connection from the carburetor and tank. Sometimes hoses stretch, and air is sucked around around the fittings. With a sharp press on the gas key, the mixture becomes depleted (gasoline is less than a stichiometric indicator) and the motor stalls. This also happens when the gasket between the carburetor and the cylinder is pierced or the bolts of the carburetor attachment are loosened from vibration. Just in case, check them, but do not forget that two.stroke engines are made of rather fragile alloys. If you overdo it with the moment of puffing, the thread in the cylinder can be disrupted.

It is also recommended to check the fence mesh on the hose in the tank, the cork through which the hoses are inserted into the tank and blow the fuel lines. Perhaps they are clogged and a little gasoline enters the carburetor. Especially with sharp pressure on gas.

Having checked and cleaning all the systems of the trimmer for the grass, season the tank prepared by all the rules by the mixture and start from the cold state. Let me work out a few minutes at idle and try to mow fishing at medium speeds. After 10. 12 minutes of work, add speed sharply. a trimmer for grass should not stall. If this happens, change the spark plug and perform the same actions.

If during operation a trimmer for the grass, before stall, spontaneously periodically reduces or increases the revolutions, “failures” appear in power, then it is necessary to check the ignition coil and contacts of all wires. Start with contacts, they are quite fragile and can break off or oxidize.

How to prevent sudden breakdowns during the operation of a trimmer for grass?

So that the unit is always in a functional state, it is worth observing several simple rules:

• Carry out timely, regular technical inspection of the main mechanical nodes of the device.
• Refill a trimmer for grass with exceptionally fresh fuel, the quality and origin of which is not in doubt.
• Check after each use of the tool, whether oxides and soot on the surface of the ignition system were formed.
• Avoid the strong load of the trimmer for grass during work.

In order for the unit to remain in a working state, it is necessary to properly prepare it for storage in the winter period. First of all, you should completely disassemble the tool, and then perform washing and cleaning the constituent elements. It is also important to examine the functional blocks for damage, with the need to eliminate the deformation of the parts, all kinds of distortions, gusts of materials.

Placing a trimmer for storage grass, it is worth filling the gearbox with a sufficient amount of oil. Then you need to clean the air filter, partially disassemble, blow and rinse the unit engine. Having dried all the mechanisms, lubricate moving elements. To carry out the processing of the piston system with oils, it is necessary to first extract the spark plug. Then you need to move the piston to the extreme position, then pour a small amount of oil into the candle hole and make scrolling the crankshaft. If the gasoline trimmer for grass in the offseason is not planned to be stored in the house, it is recommended to tightly wrap the engine of the unit with an oiled rag. This will avoid the development of corrosion on the surface of important components of the mechanism.

The most common malfunctions of the lawn mower

As for problems with failure or jamming of the engine, they are practically not found in the lawn mowers of the cart type, which we consider in the article. These malfunctions are more likely inherent in the gas.type gasoline braids and make up almost half the reasons for their users’ contacts in service centers.

Build your home!

When purchasing a lawn mower, you must be prepared for the fact that, as in all other similar tools, breakdowns may also appear in it that will require repairs.

But do not immediately run to the service center and pay big funds to the craftsmen who convince you of the presence of severe malfunctions in the device.

The lawn mower stalls at high speeds

Perhaps more and more a widespread complaint associated with gasoline trimmers sounds like this: “The lawn mower stalls”.

Naturally, a rather harsh fault may be a prerequisite for this. A two.stroke trimmer engine for grass does not develop turns stalling. lawn mower FS 130 give gas stalls. But in most cases, the situation is even easier than it seems to be the 1st gaze.

In order to cope with such an inconsistent, first, try to deal with its causes without the help of others, because, having found out the reason, it’s even easier to fight with the inconsistency, and from time to time it is even self.destructive.

In fact, circumstances, this is when the lawn mower stalls at high speeds, there are quite a lot of these circumstances.

Why is a Chinese lawn mower not developing momentum?

Trimmer for grass does not gain momentum. very frequent inconsistency and of course does not always have a common solution.In this.

The lawn mower is not gaining momentum, the cause of the malfunction and eliminate it

1st launch of the latest lawn mower.Removed the grid from the silencer, began to work.

Another, this is the presence of malfunctions in the power system.

In this case, the lawn mower will stall at idle. At speed stalls a trimmer for Champion grass. GAPHOLLOSKALL GOODLUCK 4300 stalls video revolutions. The lawn mower stalls when you press the gas. At high speeds, the lawn mower stalls. The problems with the power system may lead to a drainage or incorrect carburetor adjustment.

Vibrations that take place in the process of operation of the lawn mower can lead to a reservoir.

Incorrect adjustment of the lawn mower can be fixed by simply adjusting it in accordance with the requirements specified in the operating instructions.

In addition, sometimes gasoline trimmers for grass can stall due to the fact that the valve located in the gas tank cover just clogged or stick.

To find out, try using a braid by loosening the gas tank cover.

If in this mode the device works properly, clean the valve.

over, the lawn mower can stall due to poor fuel flow into the carburetor

Why then the device starts up, ask you?

The reason for this is that at first the fuel gradually falls into the carburetor and is enough for work with increased power.

However, then it is produced and at large speeds the engine begins to stall.

As for the carburetor, here the problem may also be that its body is too pulled.

The reason that the lawn mower stalls at high gas speeds may also be an air leak.

We are talking about the possible presence of a place through which air can pass during the heating process of the engine.

Among other things, do not forget to check the fuel intake hose. GAPHOLLOSKALL GOODLUCK 4300 stalls video revolutions. Husqvarna trimmer stalls when loading. The problem may be that it is weak or cracked at all.

These are the main reasons why the gas mowl can stall.

What to do if a benzotrimer is not gaining momentum ?

If you once purchased a trimmer for grass, working with gasoline, then you probably had to face the problem of turning on a trimmer for grass, as well as a problem as a benzotrimer does not gain momentum.

That is why this article has been created.

So, what to do if a trimmer for grass, working for you for several years, suddenly just stops gaining momentum. and the motor is simply stalling? In this case, you and I should consider a number of problems related to stopping the work of the motor.

The motor may stall under various circumstances. I have the problem of the STIHL FS38 STIHL FS38. Sometimes the reason for the incorrect operation of the trimmer for grass working from gasoline is the clogging of the air filter.

It is the filter that is one of the most important reasons why the operation of a gasoline trimmer for grass may stop.

Various garbage very often gets into it, particles of dust that also clog the filter, so it needs to be cleaned and washed every month, and maybe more often, it all depends on what power the gasoline trimmer has for the grass, as well as then how often do you use this device.

Benesotrimer (Moto Mower) Carburetor repair does not work does not develop speed, loss of power

Chinese lawn mower Analog Husqvarna does not develop turnover, the reason was very simple (watch in the video)

If you have done operations with the filter, but the work of a trimmer for grass working from gasoline remains the same, the benzotrimer does not gain momentum what to do?

Then you should try to extract the filter from the device in order to provide the so.called “relief” of the trimmer for grass. Why is a Chinese lawn mower not developing speed, the cause of Husqvarna. Should help.

The next and rather common problem when working with a gasoline trimmer is that it simply stalls and does not give any signs of life.

In this case, the problem may be as follows:

The last and most common cause of the breakdown of a gasoline trimmer for grass is that the cable that is located in the carburetor department was just sleeping.

Therefore, make sure that it will be well pulled, but not to the limit, otherwise with too much load on the gasoline trimmer for grass, this small cable can crack and then you will definitely have to contact the service center, and then also throw out many money into the wind.

The Stihl 180 chainsaw does not develop turnover or if you released the gas trigger, it continues to work without dropping in this case the moment. These obstacles are quite all.prominent. Let’s try to understand the reasons for which the appearance of similar defects is. We will also then see how to conduct diagnostics if the chainsaw does not pull. Circus.

Oleo-Mac Speedgo Head Tutorial Mac 753 T Read more on the website of Oleo-MAC-755-Master/ ! OLEO-MAC 753 Lawn Machine Two Cylinder (cm. cube) 40.2 power (kW/l.With.) 1.6 / 2.2 weight (kg) 7.9 pipe diane (mm) 28 volume of the gas tank (l) 0.75.

From personal experience

lawn mower or trimmer for grass

Trimmer for grass is a broader concept than a lawn mower (lawn mower), since it can also be an electric. The gasoline trimmer for grass and the lawn mower is the same thing.

Some authors assure that a trimmer for grass is a weaker tool, unlike a more powerful lawn mower, which can be used to mow shrubs. Personally, I have a tool with a maximum capacity of 1.7 kW and capable, as stated in the instructions, to mow a small shrub up to 10 mm thick. User manual is called “trimmer for gasoline grass”.

The proportion of the fuel mixture

I read somewhere that if the law mowing manual and the canister with butter indicates different proportions of the preparation of the fuel mixture, the proportion indicated in the manual should be used.

It was done for a long time. excess oil flowed out of the engine to the gas tank and the fiber was constantly formed on the candle, since the leadership indicated a proportion for a running.in engine 1:25, and on the canister. 1:50. After the transition to a proportion of 1:50, the appearance of oil fluxes stopped. The candle continued to burn, but with less intensity (the carburetor has not yet been adjusted).

Until now, some users of the benzo tool determine the fuel mixture “by eye”. If when preparing the mixture the amount of oil is underestimated, after a while an extraneous sound may appear immediately after the engine starts, gradually disappeared during heating, and the engine stop occurs with a sharp jerk. The continuation of the operation of a trimmer for grass in this mode will lead to its failure.

Clead cleaning

In the worst times of the work with a trimmer with an unresolved carburetor, the engine stopped starting after using each fuel tank. And only after cleaning the candle from the car, could you continue to work.

For cleaning the electrodes, fine sandpaper was used, and a thin stationery clip with a bent end was used to clean the space between the insulator and the case. At first, the electrodes were wiped with high dirt with a rag, then cleaned with sandpaper. After that, the candle fell into the diesel fuel and the moistened carpet was opposed by a paper clip from the surfaces of the insulator, the inside of the body and between them. Further, the candle fell several times into the diesel fuel, which then shake off it along with the pollution. Sometimes the procedure for cleaning a paper clip and washing were repeated. After that, the candle wiped dry and was ready for further operation.

Невероятно, но один бачок топливной смеси при неотрегулированном карбюраторе может израсходоваться менее, чем за 10 минут — проверено на практике, когда триммер для травы был запущен и эксплуатировался на высоких оборотах с максимальной подачей топлива (регулировочный винт был откручен намного больше нормы).

You can order seeds of vegetables and flowers, plant protection and microme-sharing products in the online store. Low and good germination on customer reviews. Mail delivery.

The lawn mower is a mobile high.performance tool for ennobleing personal plots and adjacent territories. With prolonged operation due to wear of parts or production marriage, there are malfunctions that lead to the fact that the trimmer for the grass stalls or does not start. Since this tool is a rather complicated mechanism, because the reasons why the lawn mower stalls can be several.

There are two main ways to eliminate problems: transmitting braids for grass to a specialized center or solving the issue with your own hands. The first option is suitable for those who are ready to lay out a “round” amount to restore the performance of the unit, and the second for someone who has basic locksmith skills and can independently deal with the causes of breakdowns and ways to eliminate them.

It is currently customary to classify breakdowns by which the lawn mower stalls in the following categories:

• mechanical damage to the ICE crankcase, malfunctions of the cylinder.piston group (CPG);
• breakage associated with the supply of fuel mixture (air filter, carburetor);
• problems due to damage to tubes, hoses, cables or ignition circuits.

If you once got a trimmer for grass, working with gasoline, then you probably had to face the inconsistent of the inclusion of a trimmer for grass, as well as such an inconsistency as a benzotrimer

So, what to do if a trimmer for grass, working for you not for the 1st year, suddenly just stops gaining momentum, and the motor simply stalls? In this case, you and I should see a number of troubles related to stopping the work of the motor.

The motor may stall under different circumstances. The EFCO Stark 25 Benzotrimmer does not develop momentum as if I gasp for a quarter what to do. From time to time, the prerequisite of the incorrect work of the trimmer for grass working from gasoline is clogging of the air filter.

Specifically, the filter is one of the most basic circumstances according to which the work of a gasoline trimmer for grass may end.

Different garbage very often gets into it, particles of dust that also clog the filter, because it must be cleaned and washed every month, and maybe more often, everything is depending on what power the gasoline trimmer has for the grass, also how often you use this device.