DIY Tiller Seat

DIY tiller adapter

DIY tiller adapter

The land cultivation process is laborious and requires a lot of effort on the part of the operator. With the help of the adapter, you can make working with the machine much more comfortable and faster. The adapter is a device consisting of a seat, two wheels, a drawbar and controls. The adapter allows you to attach a variety of attachments to the tiller, raise and lower it to a certain height. To connect the adapter, you need to purchase a single hitch. The operation of the tiller with the adapter is greatly simplified.

In order to make an adapter for a tiller with your own hands, you do not need to have any special skills and also do not need to exert much effort. The design itself is not complicated, and its manufacture is a rather entertaining process..

A rectangular pipe measuring 1.7 m is usually the base of the adapter. A smaller pipe, 0.5 m long, must be installed across it using welding, and the wheel racks will be mounted to it. The height of such racks will reach 0.3 m. Wheels for a homemade adapter will fit from an ordinary household wheelbarrow. However, please note that their inner sleeves must be expanded with a lathe. After that, bearings of the appropriate size are installed on the bushings..

Next, you need to attach the braces to the main pipe and the wheel plugs of the adapter for the tiller with your own hands. Their length can vary, but it depends on the angle that needs to be taken into account. After. it is important to calculate and start welding the frame for mounted equipment. Thanks to the bolts on the wheel rack, the side pipes will be installed. The diameter of the bolts should be rather large, since it needs to withstand different mechanical loads.

A channel 10 is fixed on the rear section of the frame for tent equipment. The side pipes and the rear channel must have an equal length of 40 cm (square frame). Also, a handle with three so-called “knees” is attached to the frame, the length of which is 19.3-50 cm. Another lever is attached to the side of the handle, but already much larger – its length is 75 cm, and it is designed to increase the supplied efforts.

Such an adapter will become easy to ride on the ground while working on arable and virgin land. Also, if desired, an appropriate blade can be adapted to it, which is useful for clearing snow. In the front of the adapter for the tiller, a do-it-yourself hitch is localized, which can be found on sale or assembled by yourself.

Please note that the fastening of the adapter and the tiller must be secure. At the top, a metal post is fixed to the main pipe, on which the seat will be installed.

A tipper body serves as an additional device. For its manufacture, you can take a box or a simple cart (country wheelbarrow). The steps for installing the body are as follows: first, the frame with the rear axle is extended, then the eyes of the bogie and the sliding frame are aligned, the pins are inserted, the bogie handle is installed on the necessary supports and secured with a corresponding lock.

As you can see, there should be no difficulties in making an adapter for a tiller with your own hands. All you need is the right materials. By making such an adapter, you will greatly simplify the work on the site, you will not waste a lot of effort and energy on routine complex processes in the field. In addition, you can make other attachment tools yourself. For example, a disc hiller. There is absolutely nothing complicated in creating it, but the result. just lovely! However, you will read about this in another article..

DIY trailer for a tiller

Body

It is not difficult to make a body. Here the most diverse materials are selected. You can use a board, steel sheets, if desired, a complex option is also suitable.

It is better to make the base of the body from metal. Several sheets of metal are selected that will correspond to the drawings. Then the base is welded. The sides are exposed at the edges, while being welded or mounted on the bolts at the bottom and at the corners. In order to strengthen such sides in the corners, you can weld the corners. You can also strengthen the bottom of the trailer. To do this, another additional layer is screwed or welded to it..

It is important to consider here whether the trailer will be tipper. If not, then the sides can be made folding by attaching them to the bottom on a movable joint, and a clutch mechanism can be made at the corners. The body is attached to the frame by three metal beams and fixed with bolts.

Chassis

It is better to take wheels for a trailer from any other equipment (preferably with a hub). The wheels are attached to a rod, which is pre-sharpened to the size of the bearing in the hub. It is important to choose the correct rod length. In order for the chassis to withstand the loads, the wheels should not go beyond the line of the boards. We install the rod on the side members. It goes inside the kerchiefs and through the racks.

It is possible to install two axles on the trailer. This will increase the stability of the trailer and distribute the load..

When creating a chassis, you can also make brakes for the tiller trailer. There are many options here, but many of them are not entirely effective. A good option would be to use a motorcycle brake system. We will need a brake drum, traction and cable. The drum clings to the rear wheel hub. There are small spaces between the drum lugs. They need to be rolled with a wire of large diameter. Then we take the disk and grind it. We weld a piece of pipe to the edge of the disc so that it does not slip.

The assembled disc must be secured with a bushing on the axle. The brake pads sit on the axle, a cable is drawn from them to the lever. Such a brake clings to one wheel, but it performs its functions perfectly. We get effective braking, which is complemented by a brake on the tiller.

Advantages of homemade and purchased trailers

You will have to spend a lot of time and effort on a homemade option. But, he also has a number of advantages:

  • in the presence of the necessary materials, such a trailer does not require large investments;
  • for homemade equipment, you can set the dimensions and parameters that are most suitable for the user;
  • the owner of the tiller himself selects parts for the trailer, which means you can be sure of the quality of components, connections and the unit as a whole.
  • The trailer is made clearly for a specific model of equipment, which makes working with it as simple and efficient as possible..
tiller, seat

Where to begin?

The first step in creating a trailer for a tiller with your own hands will be the development of a drawing. He will help you choose the right quality materials, determine their size, make a clear action plan, think over funny moments in advance.

The process must be taken as seriously as possible. In the drawing, the trailer is drawn from different sides, the dimensions of the parts are signed next to each of them. It is advisable that when creating a drawing, the proportions are clearly maintained. Separate more complex nodes, you need to draw individually close-ups and also from different sides.

When working on a drawing, it is important to think through the following points:

  • it is necessary to foresee in advance what parts and assemblies need to be interconnected, and what type of connection will be used in this case. Prepare the required number of rivets, bolts or a welding machine in advance;
  • it was decided to make a dump trailer (with automatic tipping) or a conventional one with manual unloading;
  • what scheme to use in the turning units. It can be a bearing, axle, bushing. They will also need to be prepared in advance..

After the drawing is drawn in detail, you need to study it again and think over the key points. After that, you can already make the purchase of materials. In order to save money, it is better to first carefully review your stock of metal and wood structures. Perhaps something can be used in work.

Materials and stages of assembly of the future device

First of all, you need to decide on the main parts of our cart. The first thing that is included here is a frame, complete with a linkage for the mechanized part. Without fail, you need a frame and, directly, the body itself. All this is installed on an axle with wheels (if desired, on two). Well, and finally, in the front part, the driver’s seat is placed above the traction.

How and what to make a trailer for a tiller with your own hands

Tiller is a multifunctional agricultural equipment. But, it owes its functionality, to a large extent, to the additional attachments that are used with it. An example of such equipment is a trailer for a tiller. With its help, you can conveniently transport garbage, building materials, fertilizers, seedlings, products from fields and gardens.

In this publication we will figure out how to make a trailer for a tiller with our own hands..

  • Advantages of home-made and purchased trailers
  • Where to begin?
  • DIY trailer for a tiller
  • Materials and stages of assembly of the future device
  • How to make a frame
  • Body
  • Chassis
  • Seat
  • Clutch
  • s

Pros and cons of the rear adapter

This unit is located behind the tiller. Length – 298 cm, and the height of the seat does not exceed 75 cm.Its turning radius reaches 320 cm.

This device easily overcomes medium-sized obstacles. If there is a load of 50-60 kg in the body, overcoming obstacles becomes more difficult or impossible.

It is impossible not to pay attention to the high carrying capacity, which is 450 kg. Of no small importance is also high maneuverability, which makes it possible to easily turn around in a small area..

If there is a need to use additional devices or attachments for soil cultivation, you can easily remove the body and, after compressing the rear beam, perform the hitch. This possibility increases the practicality of using the device..

Front adapter

Structurally, it is similar to the previous type of adapter, but at the same time it has a hitch mechanism at the back. This means that we get a full-weight front adapter for the Neva brand tiller. The presented design is completely disassembled, which greatly simplifies its subsequent transportation. Naturally, the cost of any additions to the unit is formed separately..

Front adapter specifications:

  • length – 190 cm;
  • width – 81 cm;
  • height – 140 cm;
  • ground clearance – 30 cm;
  • wheel track – 75 cm;
  • speed indicators – approx. 10 km / h;
  • total weight – 65 kg.
tiller, seat

.

Steering adapter

If you have the skills, then if you wish, the design can be somewhat complicated by making a homemade adapter to the tiller, to which you can also attach the steering.

To implement this idea, you will need to prepare the following materials and tools:

  • welding machine;
  • seat;
  • 2 wheels; steel pipes and corners;
  • iron sheets.

With this design, the adapter frame must be firmly connected to the tiller, otherwise the device will, as they say, “lead along the sides.” For the design, you can take any ready-made steering wheel, even from old “soviet” cars (from the same from VAZ, for example).

Adapters for any tiller, including the Neva, make it possible to significantly increase the operator’s comfort when driving a mini-tractor. In fact, the driver no longer has to constantly drag behind the device. Now he can just sit in a comfortable seat and do everything the same, only with comfort and more warmth..

The design of such units is quite simple, and independent production of them at home is quite possible. Here it must be borne in mind that home assembly implies the presence of at least basic skills in welding, as well as accompanying tools. You will also need to stock up on a large number of corners and metal pipes so as not to stop working due to a lack of material. In general, the expediency of hand-made assembly of the adapter is, especially considering that this significantly saves money.

Drawings of key adapter assemblies

Coupling mechanism. It looks like a welded structure inserted into the main frame and bolted to it. Consists of two pieces of square pipe welded onto each other and a piece of regular “water” pipe with a gauge of 1.1.5 inches.

In the pipe, not fully inserted, clamped by a bolt, a stem with a welded on homemade tee. The stem is lubricated with grease and allows the tee to rotate along the axis, to provide a rolling effect when moving on uneven ground.

Wheel attachment assembly. The structure consists of two perpendicularly welded pipe sections. The horizontal section is inserted into the fixing pipe and bolted together. On the vertical part, an axle with a wheel is fixed (on bearings).

Other nodes of the adapter are not so important, and we will not consider them..

Tiller adapter – types, sizes and designs

Steering devices

Such devices make it possible to rebuild the tiller into a full-fledged mini-tractor, the only difference, as already mentioned, is the preservation of the power of the engine used in the unit. It is attached to the tiller by means of a hitch, which is located in front of the adapter. Such a block is perfect for motors such as Sadko, Don, Plowman, Forza, Huter, Champion, Profi.

In particular, this adapter includes: steering; pair of wheels; clutch; brake and gas pedal; driver’s seat; frame structure.

Behind such an adapter there is a special lifting mechanism, to which it is possible to connect additional trailed and attached equipment.

As for the steering adapter specifically for the Tiller Neva, it has the following technical characteristics:

  • wheel track – 60 cm;
  • total weight – 105 kg;
  • ground clearance – 35 cm;
  • speed indicators – about 15 km / h.

DIY tiller adapter drawings and dimensions

Below, there are drawings and dimensions, as well as materials necessary for the manufacture of an adapter for a tiller of complex design..

What you need when making an adapter

– Metal sheets for leg supports

– Square metal. Profile

Below is a kinetic diagram to help balance the structure and avoid additional stress. The drawing below shows a diagram of a mini tractor made from Tiller Neva.

The engine of the power unit (2), driving the front wheels (1), transmits the torque through the chain (3) to the reverse gear (4), and from it through the cardan transmission (5) to the rear axle (6), driving rotating rear drive wheels (7).

– When making a frame, you must not forget about the device of the hub and fork, to ensure free rotation of the trailer.

– The body of the adapter to the tiller is made of steel sheet, and the sides of the body must be at least 30 – 35 cm high.

– The seat is installed on a beam welded to the main frame with bolts. The distance from the beginning of the frame to the seat should be 80-90 cm.

How to repair a torn scooter seat cover

– Checking the robustness of the entire mechanism.

DIY tiller adapter selection

Homemade adapter to Tiller Neva

All-wheel drive adapter AMPK 500

Tiller adapters, what they are?

  • With lifting arm. This model will facilitate management, movement across the area;
  • For the carriage of goods. Adapters are equipped with special bodies with maximum load;
  • Short or long drawbar. Short view for a light tiller, long view for a heavy unit;
  • Telescopic drawbar. This design provides for width adjustment.

Wheels

The square profile is connected by welding at an angle of 90 degrees. The part of the unit that is located horizontally is equipped with an axle for attaching a wheel from a garden wheelbarrow.

Swivel adapter.

It is about the vertical axis. Where the connection between trailer and tiller is movable.

Such a structure is more difficult to manage, but it is much easier to create such a module with your own hands. More effort is required when turning. The module can also be mounted front and rear..

Even a primitive tiller design needs load balancing. Therefore, it is advised to place the seat in the module next to the drive axle. Under the driver’s weight, the wheels of the tiller will be pressed to the ground, which excludes slipping during movement.

Tips & Tricks

All dimensions and calculations are based on visual or operator physical data. Specific conditions are not provided, so you can increase the size of the homemade device relative to the tiller itself.

For example, for a frame, the location of the axis relative to the height is often done by eye. It is important that the general horizontal of the structure is observed..

It is better to position the operator’s workstation slightly below the horizontal. This will provide better stability..

Wheels are increasingly placed not on the axle, but on the principle of a primitive portal suspension. This is how they achieve the desired clearance without unnecessary details. No elastic elements are needed, high-profile tires are enough. They will provide amortization.

To ensure a flat surface for the period of welding, you can take a sheet of plywood, chipboard. Wooden material will lose its original appearance, but the frame will be welded at the right angles.

Rear Seat Delete DIY [Super Seicento]

It is advisable to place the operator’s seat so that in any position the human body is tightly pressed against the back of the seat.

It is very convenient when there are control levers next to the seat. They are needed to control accessories..

Suppose there are mounts for a mounted plow or tiller on the back of the homemade adapter. It is more convenient to work if the additional module is regulated by a rod, which changes the height of the working elements.

Hitch

The finished structure for the coupling is a few pieces of a square profile and a regular round pipe for “contact”.

This section of pipe that goes to the connection must be equipped with a clamping bolt. The active part of the hitch is lubricated with grease to avoid rolling and rapid wear.

There are two types of coupling:

  • One-story;
  • Two-story.

Working with important parts of the adapter design

Homemade adapter for the tiller do it yourself

  • Tiller adapters, what they are?
  • By type of construction
  • How to make an adapter for a tiller with your own hands
  • Working with important parts of the adapter design
  • Simple instruction
  • All components for a steering structure
  • Tips & Tricks
  • Summarizing

A homemade tiller adapter means a regular trolley equipped with a pair of wheels, a comfortable seat and a secure mount..

Without such a device, it is impossible to work on a personal plot, to quickly loosen the soil. A normal tiller ride is not feasible without an adapter.

Here’s what you can do by attaching a comfortable seat to the tiller:

  • hilling;
  • digging;
  • transportation of goods or crops;
  • remove snow in winter.

Buying such attachments now is not a problem. How about making your own tiller adapter? About the detailed manufacture of a homemade adapter for the tiller further.

How to make an adapter for a tiller with your own hands

The adapter is a simple design having a conventional trolley seat mounted on a single axle frame.

Here is what is most often taken to work from scrap materials:

  • metal corners;
  • scrap metal for leg support;
  • square profile;
  • two garden wheels;
  • any welding device;
  • locksmith tools;
  • steel for the body (if planned in the structure).

To calculate the load, you must familiarize yourself with the diagram below, even before starting work:

The diagram below is for working on the module itself:

The order of work is performed according to the following principle:

  • Collecting the frame. For mobility, it is necessary to equip this structure with a fork and a bushing;
  • Body welding. You will need steel that is resistant to corrosion. Recommended board height not less than 30 centimeters;
  • Seat. Bolt-on. The recommended distance from the beginning is 80 centimeters;
  • Connection to the moving block;
  • Test;
  • Cosmetic work.

Swivel adapter.

It is about the vertical axis. Where the connection between trailer and tiller is movable.

Such a structure is more difficult to manage, but it is much easier to create such a module with your own hands. More effort is required when turning. The module can also be mounted front and rear..

Even a primitive tiller design needs load balancing. Therefore, it is advised to place the seat in the module next to the driving axle. Under the driver’s weight, the wheels of the tiller will be pressed to the ground, which excludes slipping during movement.

Hitch

The finished structure for the coupling is a few pieces of a square profile and a regular round pipe for “contact”.

This pipe section that goes to the connection must be equipped with a clamping bolt. The active part of the hitch is lubricated with grease to avoid rolling and rapid wear.

There are two types of coupling:

  • One-story;
  • Two-story.

Steering adapter.

This type implies a rigid connection with the tiller. The steering gear is designed as a separate unit.

Moreover, a pair of wheels, acting as a steering drive, can be installed in front or behind. Everyone is guided by their own preferences. The location of the steering gear is still related to spare parts, everyday use.

Feature in management. Manipulating a “home” tractor with a homemade adapter is no more difficult than an ATV.

Tips & Tricks

All dimensions and calculations are based on visual or operator physical data. Specific conditions are not provided, so you can increase the size of the homemade device relative to the tiller itself.

For example, for a frame, the location of the axis relative to the height is often done by eye. It is important that the general horizontal of the structure is observed..

It is better to position the operator’s workstation slightly below the horizontal. This will provide better stability..

Wheels are increasingly placed not on the axle, but on the principle of a primitive portal suspension. This is how they achieve the desired clearance without unnecessary details. No elastic elements are needed, high-profile tires are enough. They will provide amortization.

To ensure a flat surface for the period of welding, you can take a sheet of plywood, chipboard. Wooden material will lose its original appearance, but the frame will be welded at the right angles.

It is advisable to place the operator’s seat so that in any position the human body is tightly pressed against the back of the seat.

It is very convenient when there are control levers next to the seat. They are needed to control accessories..

Suppose there are mounts for a mounted plow or tiller on the back of the homemade adapter. It is more convenient to work if the additional module is regulated by a rod, which changes the height of the working elements.

Wheels

The square profile is connected by welding at an angle of 90 degrees. The part of the unit that is located horizontally is equipped with an axle for attaching a wheel from a garden wheelbarrow.

Tiller adapters, what they are?

  • With lifting arm. This model will facilitate management, movement across the area;
  • For the carriage of goods. Adapters are equipped with special bodies with maximum load;
  • Short or long drawbar. Short view for a light tiller, long view for a heavy unit;
  • Telescopic drawbar. This design provides for width adjustment.

Wheels

The square profile is connected by welding at an angle of 90 degrees. The part of the unit that is located horizontally is equipped with an axle for attaching a wheel from a garden wheelbarrow.

How to make an adapter for a tiller with your own hands

The adapter is a simple design having a conventional trolley seat mounted on a single axle frame.

Here is what is most often taken to work from scrap materials:

  • metal corners;
  • scrap metal for leg support;
  • square profile;
  • two garden wheels;
  • any welding device;
  • locksmith tools;
  • steel for the body (if planned in the structure).

To calculate the load, you must familiarize yourself with the diagram below, even before starting work:

The diagram below is for working on the module itself:

The order of work is performed according to the following principle:

  • Collecting the frame. For mobility, it is necessary to equip this structure with a fork and a bushing;
  • Body welding. You will need steel that is resistant to corrosion. Recommended board height not less than 30 centimeters;
  • Seat. Bolt-on. The recommended distance from the beginning is 80 centimeters;
  • Connection to the moving block;
  • Test;
  • Cosmetic work.

By type of construction

Tips & Tricks

All dimensions and calculations are based on visual or operator physical data. Specific conditions are not provided, so you can increase the size of the homemade device relative to the tiller itself.

For example, for a frame, the location of the axis relative to the height is often done by eye. It is important that the general horizontal of the structure is observed..

It is better to position the operator’s workstation slightly below the horizontal. This will provide better stability..

Wheels are increasingly placed not on the axle, but on the principle of a primitive portal suspension. This is how they achieve the desired clearance without unnecessary details. No elastic elements are needed, high-profile tires are enough. They will provide amortization.

To ensure a flat surface for the period of welding, you can take a sheet of plywood, chipboard. Wooden material will lose its original appearance, but the frame will be welded at the right angles.

It is advisable to place the operator’s seat so that in any position the human body is tightly pressed against the back of the seat.

It is very convenient when there are control levers next to the seat. They are needed to control accessories..

Suppose there are mounts for a mounted plow or tiller on the back of the homemade adapter. It is more convenient to work if the additional module is regulated by a rod, which changes the height of the working elements.

All components for a steering structure

  • Frame base. Elastic elements are not provided. Can be pavement, axial, portal, rotary;
  • Equipment connection. When the adapter itself is located at the back;
  • Coupling device. In any design, this is the most vulnerable part. The main task is to ensure a reliable connection of the tiller with the module, stability. When there is steering, the hitch is rigid. In terms of degrees of freedom, it is designed for swivel or twisting;
  • Operator’s seat. Must be positioned at a safe distance. Sometimes equipped with additional levers to control the active part;
  • Rigid hitch steering device. The use of old steering systems from cars is allowed.

Hitch

The finished structure for the coupling is a few pieces of a square profile and a regular round pipe for “contact”.

This section of pipe that goes to the connection must be equipped with a clamping bolt. The active part of the hitch is lubricated with grease to avoid rolling and rapid wear.

There are two types of coupling:

  • One-story;
  • Two-story.

Tiller adapters, what they are?

  • With lifting arm. This model will facilitate management, movement across the area;
  • For the carriage of goods. Adapters are equipped with special bodies with maximum load;
  • Short or long drawbar. Short view for a light tiller, long view for a heavy unit;
  • Telescopic drawbar. This design provides for width adjustment.

Swivel adapter.

It is about the vertical axis. Where the connection between trailer and tiller is movable.

Such a structure is more difficult to manage, but it is much easier to create such a module with your own hands. More effort is required when turning. The module can also be mounted front and rear..

Even a primitive tiller design needs load balancing. Therefore, it is advised to place the seat in the module next to the drive axle. Under the driver’s weight, the wheels of the tiller will be pressed to the ground, which excludes slipping during movement.