Do-it-yourself tracked drive for a walk-behind tractor

Tire tracks

The next way to make such a movement unit with your own hands is with the help of old car protectors of a car or tractor. Such a caterpillar attachment to the walk-behind tractor is quite practical and easy to manufacture. Another advantage of this method is the absence of the need to manufacture special lugs.

do-it-yourself, tracked, drive, walk-behind

First, you need to cut a tread track from the old tire with your own hands and carefully separate its side surfaces. Cutting off the side surface is quite problematic. This can be done manually with a well-sharpened knife.

However, in this case, the process may be delayed, and it is unlikely that you will cut the side part efficiently and accurately. An ordinary jigsaw can come to the rescue. It is best to use a fine-toothed file. In order to reduce the friction of the jigsaw blade, periodically moisten it with water or a special soap solution.

After you have removed the beads, remove excess layers from the seamy side of your workpiece if necessary. This must be done if the resulting track is too hard.

Tip: If you notice that the tread pattern does not fit, it is better to re-cut new lugs.

The resulting track is perfect for your walk-behind tractor, since it will initially have a closed loop, therefore, its reliability will be higher. Among the disadvantages of a tire travel unit, a limited width can be noted. Although this disadvantage can be avoided if you use a double or triple tread.

What caterpillars can be made from

Nowadays, many people try to develop and make improvised all-terrain vehicles with their own hands, but it is very problematic to make a caterpillar for a walk-behind tractor, since it must be light and durable at the same time. Below we will provide several ways to implement this idea.

To make a tracked module for a walk-behind tractor, you can use available tools. The easiest way is to make homemade tracks using a roller chain and conveyor belt.

In order to make a caterpillar with your own hands from these materials, you do not need special tools or machines. Homemade conveyor belt and chain tracks can be stitched from the edge with fishing line to extend their lifespan. When flashing, observe a step of 1-2 cm.

You can connect the tape into a ring in different ways:

  • you can use a hinge that is similar to a piano hinge;
  • you can sew the edges of the tape, but this method will not be reliable.

Tip: Select the thickness of the future caterpillar depending on the power of your walk-behind tractor.

For high-power units, tape 7-15 mm thick can be used. It is also used for agricultural machinery. However, remember that you need to carefully install such a tape, since its weight is quite large.

Do-it-yourself caterpillars for a walk-behind tractor photo and video

Date of publication: 11/21/15

Track links manufacturing

A plastic water pipe cut in half, with an outer diameter of 40 millimeters, a wall thickness of 5 millimeters, was used as tracks. it is screwed to the conveyor belt using M6 bolts with a wide head, a grover washer, a nut. I did not bend the washers beforehand, they perfectly take the shape of the surface when tightened. The connection of the conveyor belt is made in this way: the same bolts as used in the fastening of the track, 5 pieces.
The distance between the lines is 93 millimeters, I did not invent this distance myself, I found it on the Internet, shared the experience of a designer who has already built such devices. And in tests this size is ideal for the given belt thickness and for the drive sprockets used on the snowmobile.

Caterpillar manufacturing process

For the manufacture of the caterpillar, I made a special jig, it rather simplifies and speeds up the work process. The conductor itself can be made from any plywood, you make the width as the width of the tape, and mark the holes at a distance of 93 millimeters, then just press them against the tape with clamps, drill through the conductor, rearrange and so on in a circle. This is much faster than marking all the holes on the tape itself. The whole process took literally 10 minutes and all the holes for the tracks were ready. The entire track assembly is quite light, I can easily lift it with one hand.

DIY snowmobile caterpillar

The most important part of a snowmobile is its track, I want to show you a detailed overview of how to make a homemade snowmobile track. There are a lot of self-made self-propelled vehicles on the Internet, but basically everyone shows how to ride them, without showing the production itself.

Guide for the manufacture of tracks on a walk-behind tractor from improvised means

Self-made or purchased tracks for a walk-behind tractor increase the throughput capacity of the transport at times. With the help of such a device, you can independently equip a snowmobile or an all-terrain vehicle. The ready-made factory caterpillar triangular drive GP H1 is a rather expensive device. Therefore, we offer an alternative option. homemade motoblock tracks in several versions and modifications.

Conveyor belt

The technique is the easiest. In addition to the conveyor belt, it is required to take a sleeve roller chain. The ease lies in the fact that the creation does not require a large amount of additional materials and tools. To increase the period of application of the machine tape in the module, it is necessary to circle it along the edge part with a fishing line. Be sure to provide a step of 1 cm.

Particular attention is paid to the height of the material. It completely depends on how long the device will withstand. Optimally, take a tape with a height of 0.7 cm at least. There is one more wheel to be taken care of on both sides. Suitable from an old car, but at the same time it matters that the size is the same as that of a wheel on a walk-behind tractor.

Structural differences

Tracks for the Neva walk-behind tractor significantly simplify the transportation of cargo, the movement of the equipment itself. The tracked module covers a significant surface, the motoblock device rides more evenly, provides the least pressure on the road and does not slip on difficult soils. The device on tracks can function even in bad weather, and in sunny weather it has excellent maneuverability.

It is not difficult to look after and use the module on tracks, but you can build it yourself. The main thing is to understand that when the motoblock device has caterpillars in the kit, its speed mode will be less, but insignificantly.

Tracked motoblocks in the other do not differ at all from standard motoblock devices:

  • The engine is suitable for 4-stroke with the possibility of auto-locking the axis so that the technical device can turn around without turning around in a circle.
  • There is also a requirement for the mandatory arrangement of water cooling, which can cope with overloads, due to which the engine heats up excessively.
  • A tracked module of this type is more efficient than an air-cooled one.
  • Hitch system, gearbox and gearbox in the standard model design. It is necessary to control when using the handle.

A mower for a walk-behind tractor will help to quickly and efficiently remove not only grass, but also weeds and even small ones from the site.

When making tracks to the walk-behind tractor with your own hands, you need to know that if you design them very high, then the center of gravity of the walk-behind tractor will change, and it will have problems when turning, and even bending to the side. It is necessary to make the second driven axle 2 cm longer.Also, using a bushing, it will be possible to expand the wheel base already available in the motor-block.

Two more methods

Tracked motoblock machines are often created using wedge-shaped belts. Fasten them to the lugs. The belts are fastened with rivets. A popular method is to use equal sized chains. They can be found in the garage and are often left over from other vehicles. Step-by-step work:

  • Take 2 equal chains.
  • Break the extreme links, unite the chains into a single ring.
  • To brew.
  • Hooks fasten the chains together and create strong fasteners. They can be made from steel plates of the required thickness. They are bolted together.

The crawler track for a walk-behind tractor requires skills in working with equipment, with a welding machine.

How to make homemade tracks on a walk-behind tractor with your own hands

Owners of motoblock equipment often go to home-made manufacturing of components for a powerful unit. The tracked walk-behind tractor is distinguished by its maneuverability, it is convenient when processing a vegetable garden and in other works. And the tracks themselves, if you have material, experience, you can make yourself. You only need to follow a certain technique and sequence.

Car wheel

Tracked attachments for a walk-behind tractor made of car tires are a popular solution. Craftsmen say the design will be more reliable with tire tracks. To make the device practical, it is necessary to take care of the quality of the tires. Tractor tires are what you need. The tread pattern plays a role as it is a lug. The process is phased:

  • When the tires are prepared, they cut the track.
  • This is a tricky job that needs attention. A well-sharpened knife is used for cutting. It is correct to take the one used by shoemakers. Periodically, it must be moistened in a soap solution. This makes the rubber surface easier to cut.
  • Both sidewalls are cut off from the tires. To make the process easier, take a jigsaw with not large teeth. Cut off excess parts inside the tire, if required. If the track turned out to be hard inside, it is allowed to cut it again.

The operation of gardening equipment begins with its launch. The walk-behind tractor is a design in which.

The advantage of this technique is that a ring connection is not required. The tire is already round. Therefore, it turns out to improve the strength indicators of the module, which is important in conditions of severe overloads. And yet, such designs are quite compact. The length will be the size of the tire used.

Phased technology

Several reliable DIY technologies have been developed for creating a caterpillar structure. They have shown themselves to be more reliable, so they are often used. Which one to choose depends on the skills and materials that you may need. You can make tracks for a walk-behind tractor with your own hands, following the recommendations of the masters.

Additional Tips

Before you make a tracked drive for a walk-behind tractor, you need to make drawings, determine the dimensions. They do this so that in the case of a very high self-made caterpillar for a walk-behind tractor, it will be necessary to change the center of gravity of the walk-behind tractor. This will inevitably provoke problems when turning, as the technique will fall to the side. To avoid this, the second driven axle must be made longer.

In addition to the rules regarding the power of the engine, they also look at the cooling system:

  • Air cooling is ineffective with significant overloads, which will damage the engine.
  • Properly use water cooling that has proven to be stable.

Attached attachments to the walk-behind tractor can seriously improve the data on the patency of equipment. Therefore, it is possible to diversify the range of operations carried out that a home-made apparatus can handle. To put it another way, the created base in some situations outperforms standard wheels. However, the alteration of motoblock equipment may not suit the owners of these technical devices. It talks about the special requirements for the engine.

The motor fits with good traction. Homemade production is suitable for execution in a garage. That is why the unit created in the garage is an excellent replacement for the tracked monoblock units on the market.

Necessary materials

As mentioned earlier, to turn the wheeled motoblocks Sadko, Don, Hooter, Profi, Plowman, Champion, Carver, Husqvarna into a tracked one, you will need a fairly powerful engine with axial blocking.

Power is important because such a walk-behind tractor will be used on a rather complex surface, the passability on which requires additional technical data.

Summarizing a little, we can highlight the main materials that we need:

  • The presence of the walk-behind tractor itself with a gearbox, which has a powerful 4-stroke engine with axle locking.
  • A pair of extra wheels so you can pull the track on them.
  • The homemade caterpillar itself, made from handy tools.
  • Depending on what material will be used in the manufacture, we may need two large car tires, or a transport tape.

With the help of these materials, you can make a fully functional tracked walk-behind tractor.

At the same time, you can make a full-fledged mini-tractor on tracks if you add an additional cargo platform, or use it as an all-terrain vehicle in the snow by adding a platform on skids. In general, full scope for imagination.

Two more methods

Tracked motoblock machines are often created using wedge-shaped belts. Fasten them to the lugs. The belts are fastened with rivets. A popular method is to use equal sized chains. They can be found in the garage and are often left over from other vehicles. Step-by-step work:

  • Take 2 equal chains.
  • Break the extreme links, unite the chains into a single ring.
  • To brew.
  • Hooks fasten the chains together and create strong fasteners. They can be made from steel plates of the required thickness. They are bolted together.

The crawler track for a walk-behind tractor requires skills in working with equipment, with a welding machine.

List of required materials

To turn wheeled motoblocks into tracked ones, you need a powerful motor. It must have an axial lock. Power matters because the motorball is planned to be used on a complex surface. It will not be possible to achieve good cross-country ability without additional technical parameters. The main materials that will be required for such work:

  • walk-behind tractor with gearbox, equipped with a four-stroke engine and axle locking function;
  • several additional wheels that allow you to pull the caterpillar on them;
  • directly caterpillars made from improvised means.

Depending on the material used in production, two oversized car tires and a conveyor belt may be required. All this together makes it possible to make a workable device.

If you add a cargo platform here, you can equip a full-fledged mini-tractor. An additional platform on skids provides the ability to use the device as an all-terrain vehicle in the snow.

About the device

Tracked walk-behind tractors are much less common than their wheeled counterparts. The explanation for this is quite understandable. wheeled walk-behind tractors Cayman, Patriot, Texas, Foreman, Crossser, Viking, Forza are more adapted for plowing land, i.e. its design is most suitable for work on the ground.

By the way, additional wheels can be made removable so that you can quickly turn it back into a standard walk-behind tractor for working in the garden. This can be done by attaching these wheels to an axle that we already have in stock, through a flexible or rigid gear.

This solution is most expedient, because there is no need to weld additional fasteners.

As for the device of such walk-behind tractors, they are completely identical to wheeled walk-behind tractors:

    Engine. Tracked models use a more powerful 4-stroke engine, which has an axle locking function.

This is important because it allows the tracked walk-behind tractor to turn in place without making a full circle to turn.

  • Transmission. Reducer, gearbox and clutch system. this standard set is also included in the device of tracked motoblocks.
  • Chassis. Here, in principle, everything is clear from the name. the design uses tracks instead of a wheelbase. As already mentioned, in the case of alteration, one kata is added to the existing pair of wheels on each side, on which a homemade caterpillar is already put on.
  • Governing bodies. They are located on the control handle, including various clutch levers, emergency stop of the engine, etc.
  • All-terrain vehicle made of belts and chains

    Another simple way is to make a caterpillar from belts with your own hands. This method is distinguished by its simplicity and convenience. To make tracks for a walk-behind tractor from belts, use those with a wedge-shaped profile. You need to connect them together using lugs, which are attached to the belts with screws or rivets.

    A track constructed from old, unnecessary identical chains will be more reliable. They will probably be lying around in your shed or in your neighbors’ shed. One such tape will need two chains:

    • take products of the required size;
    • unclench the last links and fold the chains into rings;
    • the edges are clamped and welded.

    The chain rings are fastened with homemade lugs made of thick steel (iron) pre-drilled plates. They are placed on the chain links of the same name on both sides and clamped with bolts and nuts.

    It is desirable that the plates facing the ground are thick so that the bolt head is completely recessed into it.

    Attaching the tracks to the walk-behind tractor can significantly increase the cross-country ability of this device. This leads to an increase in the range of potential work that the resulting walk-behind tractor can handle. In other words, the tracked base in some positions outperforms the usual wheelbase.

    However, such a reworking of the walk-behind tractor is not suitable for all owners of these units. First of all, we are talking about the special requirements for the engine used, which must be of sufficient power.

    Additional tips and warnings for making a goose yourself

    Before you start making a homemade caterpillar, you need to clearly understand its required parameters. The fact is that in the case of manufacturing a very high caterpillar, the center of gravity of the walk-behind tractor will be changed, which will inevitably lead to certain problems when turning, i.e. the unit will fall on its side.

    In addition to the requirements for engine power, it is worth paying attention to its cooling system. The fact is that air cooling does not cope very well at high loads, which leads to significant overheating of the motor.

    Thus, it is better to give preference to a water-cooled engine, which show more stable performance in operation.

    Homemade tracks for a walk-behind tractor

    • 1 Homemade caterpillars
    • 2 Step by step assembly of the tracked unit
    • 3 Are belts and chains suitable for the job??
    • 4 Tracked module with tube frame
    • 5 Conclusion

    To improve the mobile performance of garden equipment, you can purchase tracks for a walk-behind tractor or cultivator. They will allow you to use the equipment even in winter, without worrying about its maneuverability. It is expensive to purchase a tracked drive for a walk-behind tractor, so in some cases you can limit yourself to self-assembly from scrap materials. Drawings for homemade products can be drawn up independently or borrowed from the masters. With properly organized work, a homemade caterpillar will turn out to be reliable and stable.

    What are the advantages of operating tracks? The caterpillar track compares favorably with the wheel track in that a wider coverage area is used when driving. As a result, the load is correctly distributed, the pressure on the ground decreases. Maneuverability is an important advantage of this movement. Regardless of the type of soil, its density and structure, the walk-behind tractor will work without stopping with the same efficiency.

    If you install the tracks on a walk-behind tractor, then the vehicle’s characteristics will change, or rather, its speed. The walk-behind tractor will move a little slower. This minus is easily compensated by the fact that the mounted tracked module for the walk-behind tractor allows work in all weather conditions. Heavy equipment becomes maneuverable and easy to use, its course will become a little slower, but this is compensated by its new functionality.

    To date, the track attachment for the walk-behind tractor has found its widespread use among consumers. The most popular were the devices of domestic manufacturers: “Lynx”, “Ant”, “Buran”. Tracks for the Talon 380 walk-behind tractor have proven themselves quite well. All of them are distinguished by high reliability and efficiency of use. But this does not mean that a homemade caterpillar will be worse and will last less. With a high-quality assembly, it will be in no way inferior to the factory model.

    Are belts and chains suitable for the job?

    A homemade track attachment made of belts and chains is a good option for moving around for gardening equipment. This assembly method is distinguished by its simplicity and ease of use. Homemade tracks of this type are made from V-shaped belts. You need to connect them into a ring using lugs, fasten them to the belts with screws or rivets. In this case, the track attachment to the walk-behind tractor will be more reliable and will last longer.

    If chains are taken as the basis of the future caterpillar, it is worth adhering to some assembly rules:

    • you need two chains of the same size to work;
    • to fold the chain into a ring, it is necessary to unclench the last rings;
    • fasteners for reliability are connected and welded.

    The rings are secured with lugs made of thick, strong steel plates that need to be drilled in advance. They are pressed to the desired sections of the chain from 2 sides and twisted with bolts and nuts. If this is not taken into account, then making the caterpillar durable will not work.

    To prevent the bolt heads from sticking out, the plates should be as thick as possible.

    Homemade caterpillars

    How to make tracks for a walk-behind tractor with your own hands? Many, not wanting to spend money on purchasing factory-assembled products, prefer to use home-made tracks for a walk-behind tractor. Making them with your own hands, in principle, is not difficult. It is enough to show some ingenuity, creativity and minimal plumbing skills. Patience and accuracy are indispensable here. You must always remember that with a minimum of labor and money costs, a home-made track attachment to a walk-behind tractor will not differ in any way from a factory-assembled unit.

    A variety of materials can be used in the work, but it is imperative to take into account the maximum power of the walk-behind tractor engine. The tracked unit should not be heavy, otherwise there will be no point in it. It is unreasonable to mount a crawler block from a bulldozer on a walk-behind tractor. This will destroy the garden equipment motor. It is wiser to use tires from trucks for these purposes. The tread will provide reliable traction in loose snow and slippery mud.

    What can be used to make a tracked module for a walk-behind tractor? Traditionally, when a caterpillar is made by hand, a conveyor belt is used, it is taken as the basis for a future attachment for a walk-behind tractor.

    The thickness of the tape is selected based on the power parameters of the engine of the unit. The tape thickness indicator varies within 7-10 mm. For the manufacture of a tracked unit, tires from the wheels of trucks are suitable. In this case, it will take much more time and effort to make tracks for the walk-behind tractor. Drawings are required for this kind of work.

    A do-it-yourself caterpillar can be made from a conveyor belt. This is a fairly easy way to make a tracked module for a walk-behind tractor on your own. It can be safely used as the basis of caterpillar movement. No special tools or attachments are required to work. It is enough to use one of the options for connecting the tape into a ring:

    • The tape is connected by a special hinge, which in its appearance is similar to a piano hinge.
    • The edges of the tape are sewn with a fishing line with a pitch of no more than 1 cm.This method is not very reliable, it is better to use it as a temporary (or test) option.

    Step by step assembly of the tracked unit

    A homemade track attachment for a walk-behind tractor can be assembled not only from car tires, but from belts and chains. The build process is as follows:

    • First you need to make a tread track out of the tire by cutting off the sidewalls. This will require a sharp knife and physical strength. A jigsaw will help speed up the process and make the track more neat in appearance. Better to take a file with fine teeth. It is recommended to periodically moisten it with cool water or soap solution, so that it cuts the product better.
    • Next, remove excess layers from the seamy side of the track. This must be done in order for the caterpillar to acquire elasticity and softness.
    • The resulting homemade tracks will become a suitable constructive option for moving the walk-behind tractor. Their advantages are that they have a closed loop, providing a high degree of reliability of the tracked unit. The only drawback to be aware of is the limited width of the projector. And this can be avoided by using a double tread. If it is noticed that the tread does not fit the track at all, then it is better to re-cut the lugs.

    Homemade tracks for the 42hp garden tractor, Part 4, Test drive

    Tracked module with tube frame

    A homemade tracked module for a walk-behind tractor can be made with a frame made of pipes. A welding machine will help to fasten them together. You can make do-it-yourself tracks for a walk-behind tractor from the following components:

    • A frame is made of rectangular metal pipes. The spline part can be borrowed from Buran, and the drive shafts can be taken from Oka.
    • Brakes are installed on the front shafts. As a result, do-it-yourself tracks will turn out to be more maneuverable.

    Memo for those who want to make a tracked module for their walk-behind tractor with their own hands:

    Modern models of motoblocks with tracked attachments are distinguished by practicality of use, wide functionality, fairly simple control that any user can do.

    Tracked modules allow you to use the walk-behind tractor at any time of the year, regardless of weather conditions and type of soil.

    Necessary materials

    As mentioned earlier, to turn the wheeled motoblocks Sadko, Don, Hooter, Profi, Plowman, Champion, Carver, Husqvarna into a tracked one, you will need a fairly powerful engine with axial blocking.

    Power is important because such a walk-behind tractor will be used on a rather complex surface, the passability on which requires additional technical data.

    Summarizing a little, we can highlight the main materials that we need:

    • The presence of the walk-behind tractor itself with a gearbox, which has a powerful 4-stroke engine with axle locking.
    • A pair of extra wheels so you can pull the track on them.
    • The homemade caterpillar itself, made from handy tools.
    • Depending on what material will be used in the manufacture, we may need two large car tires, or a transport tape.

    With the help of these materials, you can make a fully functional tracked walk-behind tractor.

    At the same time, you can make a full-fledged mini-tractor on tracks if you add an additional cargo platform, or use it as an all-terrain vehicle in the snow by adding a platform on skids. In general, full scope for imagination.

    How to make a homemade track from belts and chains

    ATVs on tracks from a walk-behind tractor can be made using the most common belts with a wedge-shaped profile. The belts are connected to each other by means of a lug, attached to the belts with rivets or screws.

    Another method is to make the tracks from chains of the same size. Many summer residents have such material in bulk in the garage, which simplifies the search issue. The whole manufacturing process boils down to the following points:

    • Take two chains of the same size.
    • The last links of these chains must be unclenched, and then connected into a closed ring.
    • Next, we clamp the links and weld them.

    The chains are fastened to each other using lugs, which can be made from ordinary steel plates of the required thickness. They are connected to the chain with bolts.

    Additional tips and warnings for making a goose yourself

    Before you start making a homemade caterpillar, you need to clearly understand its required parameters. The fact is that in the case of manufacturing a very high caterpillar, the center of gravity of the walk-behind tractor will be changed, which will inevitably lead to certain problems when turning, i.e. the unit will fall on its side.

    In addition to the requirements for engine power, it is worth paying attention to its cooling system. The fact is that air cooling does not cope very well at high loads, which leads to significant overheating of the motor.

    Thus, it is better to give preference to a water-cooled engine, which show more stable performance in operation.

    Track module from a tire

    Caterpillars from car tires for a walk-behind tractor are also quite common homemade products, characterized by a high reliability of the design. However, in order for the resulting tracked walk-behind tractor to be practical, you need to take care of finding the right car tires.

    Farm owners are increasingly resorting to purchasing special technical devices. grain grinders, with which they can process raw materials, thus preparing feed for feeding on their own. By clicking on the link, see how to make a grain crusher from a washing machine with your own hands.

    On the domestic market of agricultural machinery, there are various options for cultivators, not only Russian, but also foreign production. The Mantis cultivator is a reliable and practical technique for decades.

    Recently, small-sized agricultural machinery has been very popular, allowing you to carry out the same work as their “older brothers”, but at the same time they cost an order of magnitude less. It’s all about the different types and characteristics of mini combine harvesters.

    In particular, they must have the required tread pattern, preferably from tractors or large machines. The tread pattern is very important because it acts as a lug and also increases the grip of the track.

    Let’s divide the manufacturing process into several steps:

    • Having found suitable tires, we need to cut out a track for caterpillars from them. This is a rather laborious work, which will take a lot of time.
    • For cutting, you can use a well-sharpened boot knife, which from time to time needs to be moistened in soapy water. this will help to cut the rubber better.
    • You also need to cut both sidewalls off the tires. To simplify the process, the sidewall can be cut with a fine-toothed electric jigsaw.
    • If necessary, remove excess parts from the inside of the tire. This manipulation must be performed if the track is too hard from the inside.

    The advantage of this method is the absence of the need to connect it into a ring, since the tire already has a closed structure. This increases the reliability of such tracks, which is quite important under heavy loads.

    However, such tracks are of a rather limited length. exactly along the length of the car tire.

    About the device

    Tracked walk-behind tractors are much less common than their wheeled counterparts. The explanation for this is quite understandable. wheeled walk-behind tractors Cayman, Patriot, Texas, Foreman, Crossser, Viking, Forza are more adapted for plowing land, i.e. its design is most suitable for work on the ground.

    By the way, additional wheels can be made removable so that you can quickly turn it back into a standard walk-behind tractor for working in the garden. This can be done by attaching these wheels to an axle that we already have in stock, through a flexible or rigid gear.

    This solution is most expedient, because there is no need to weld additional fasteners.

    As for the device of such walk-behind tractors, they are completely identical to wheeled walk-behind tractors:

      Engine. Tracked models use a more powerful 4-stroke engine, which has an axle locking function.

    Homemade tracks for the 42hp garden tractor, Part 2

    This is important because it allows the tracked walk-behind tractor to turn in place without making a full circle to turn.

    From the conveyor belt to increase the cross-country ability of the all-terrain vehicle

    One of the simplest methods is considered to be the manufacture of a caterpillar from a conveyor belt, using a sleeve-roller chain. The ease lies in the fact that for their manufacture you do not need to use a large number of tools and aids.

    To extend the service life of our conveyor belt in the tracked walk-behind tractor device, you can sew it along the edges with a fishing line, observing a step of 10 mm. To connect the tape into the ring we need, you can sew it along the ends, or use the hinge.

    Particular attention should be paid to the thickness of the conveyor belt, because it directly depends on the degree of load on the unit. The optimal choice will be a tape with a thickness of at least 7 mm. In addition, we need to take care of an additional wheel on each side.

    You can take it from an old car, but remember that the diameter must be identical to the wheel on the walk-behind tractor.

    Motoblock on Buran tracks

    If you have no desire to make your own caterpillars, then you can borrow it from old technology. For example, a walk-behind tractor on tracks from Buran shows pretty good work.

    It is advisable to use just the old part, because the new Buranovskaya caterpillar will be quite expensive, and the purpose of such alterations is the maximum cost savings.