Echo mowel stalls at high speeds. If stalled under load

Why is the Echo lawn mower stupidly gaining momentum. Why the lawn mower stalls? Immediately after you started

The modern market offers a wide range of electric and fuel trimmers of different manufacturers. In the work of equipment, failures may occur. For example, deficiency insufficiency. Do not panic about this, since the problem of the lack of revolutions in benzocosyles, trimmers are quite common. There are several reasons for this.

There are five main reasons why the trimmer for STIHL grass does not develop turns:

Low quality fuel use

Benzotrimmer does not gain momentum in case of low quality fuel. He may stall or not start at all. To check the quality of the fuel, you need to inspect the candles. They are. The main indicators for problems with the combustion chamber.

In the presence of sediment, plaque formed on the candles, the old fuel is drained and flooded another, high.quality.

It must be remembered that a trimmer for grass or a lawn mower should be refueling good quality gasoline and those fuel brands that the manufacturer indicated in the technical passport of the device.

Note! Candles should be thoroughly cleaned of plaque, and only after that place again in the combustion chamber of fuel.

Air or fuel filter pollution

There is a lawn mower does not gain speed, the reasons may be polluted by the filter element: air or fuel.

When blocking the air filter, there is a lack of oxygen in the combustion chamber, so the fuel is not fully produced, which prevents the desired speed and power.

To check if the cause is really in the air filter, you need to remove it and turn it on. If the lawn mower still does not gain momentum, the reasons are not in it. So you should check the fuel filter element. Everything is similar here, only gasoline acts as oxygen. If this filter is damaged, there will be a lack of fuel, which inhibits the development of revolutions.

In one and another case, the output is simple: you just need to replace the filter. If there is a spare, to install it, if not, to purchase in any specialized store, is inexpensive.

Problems with ignition candles

When a benzotrimer is used often, you need to monitor the state. This part is susceptible to wear, so they need to be regularly examined: is there a Nagar on them.

You can solve the problem in two ways: clean the old candle from Gary or purchase a new one.

In the first case, you need to unscrew and swing with sandpaper, dry. The distance between the electrodes should be 1 mm. Trimmer for grass is collected and advanced.

In the absence of a spark between the electrodes, it is worth inspecting the quality of the connections of all the elements of the circuit. If in this case everything is fine, then 100% you need to change the candles.

Replacing them is easy and inexpensive. From the tools will be needed a key, supervisor.

Important! With frequent appearance of soot on the candlelights, it is worth looking for a reason a little deeper.

Candles should be carefully cleaned of plaque

Problems with the engine

Engine problems. Already more serious. There are several options for a malfunction:

In the case of the problem of the carburetor, you should first pay attention to the condition of the cable. It can be weakened, which led to a problem. A simple adjustment of the cable is required here.

If this did not help, then you need to check the use parameters. These operating standards can be found in the technical passport of the device. Sometimes it’s enough to disassemble the device: to wash and collect and assemble.

note! The solution to the problem with the carburetor may be the purchase of a new element or by contacting the service for professional services.

The trimmer drive is subjected to a full check only if the manipulations with the carburetor were not given the proper result.

FLOOK DISCOUNSE

The lack of fuel circulation in the system can also be the reason why the device does not gain momentum. There are several options for why this is happening:

You can eliminate problems yourself. For this you need:

• remove blockages from the gasoline pump;
• update hoses, pipes for fuel circulation;
• Clean the muffler and mesh on it;
• Reinching a new catalyst.

Do not worry when such problems arise. This does not mean at all that the unit of poor quality. If the Patriot trimmer does not gain momentum, it can be repaired with your own hands without contacting the service.

For what reason does an electric braid for STIHL grass do not develop full power

When using an electric trimmer for the grass, non.aviation problems may also occur. Here the reasons are completely different than that of fuel cos.

You can eliminate problems yourself

Eletric trimmer for grass does not develop the required power, because:

• The voltage in the network is below the required minimum for the device more than 10%;
• There was a failure on a smooth launch (if there is such a system);
• there was a malfunction of the brush node;
• The engine winding was burned;
• rotating parts sometimes jamming.

To establish voltage, you should first check its power. If it does not meet the norms, it should be increased using a stabilizer.

The repair of the smooth start system is carried out only in the service center.

note! With wear of brushes, you just need to replace them. When installing new ones, it is recommended to clean all the surfaces with which they contact.

To establish voltage, you should first check the power.

When burning engine windings, you need to change the electric motor.

Jamming of parts of rotation can occur for various reasons. To eliminate them, you should review the entire drive unit.

Note! The last problem may also arise in another unit of this company. STIHL secateur, and the sharpening of the disk on the scissors will be its solution.

The lawn mower stall when you press the gas, how to eliminate the breakdown

The reasons why the lawn mower stalls is a huge number, we offer the most common of them, and we hope that you will find your own, and, of course, eliminate it. So, one of the situations is to clog the air damper, then the hole behind which the fuel is sprayed. If something got into it, then it can most often be quickly and easy to remove. This is the simplest reason, like a clogged filter. It needs to be washed in the solvent, and then get it well with compressed air. If it is not subject to repair, then order a new one in spare parts from the Kosikos store.

When a braid for grass stalls at high speeds, this is due to the following problems:

• clogging or clutching a valve located on the gas tank lid;
• The carburetor was diluted under the influence of vibrations arising during the operation of the mechanism;
• problems with the circulation of the fuel mixture;
• atmospheric air
• The hose intended for fuel fuel cracked or slightly connected.

The carburetor is regulated by relying on the operational instruction to the trimmer. For configuration, it is often enough to weaken the tightening of its body. If there are problematic issues with the circulation of the fuel mixture, then it can gradually enter the carburetor. After its production, the engine stalls at high speeds.

The causes of the malfunction and their elimination

In order to most accurately determine the cause of the trimmer malfunction for grass of any brand (for example, echo) and find out the possibility of eliminating it, you need to install, when performing what action the device stalls. The engine can turn off both at idle and at high speeds, heated under load or immediately after starting and t.D.

If you stalled after gas supply

Owners of gasoline braids often mention that the lawn mower stalls when you press the gas. Usually such a breakdown occurs due to problems in the carburetor. A failure in his work can occur due to long-term storage, use in difficult conditions, significant overload of the motor. The symptom of such a breakdown will be vibrating movements of the device during operation.

On a note! Users familiar with the repair of a car carburetor can try to restore this important node of the trimmer for the grass on their own, using the instructions for operating. Otherwise, the correct decision will be to seek help from the service center representatives.

Sometimes a trimmer for grass stalls when you give gas because the fuel valve is clogged. This interferes with the supply of gasoline. To eliminate the problem, it is enough to loosen the valve. Thus, normal supply of carburetor fuel will be restored.

What to do if the lawn mower stalls when you press the gas

Most often during the periods when the lawn mower stalls when the gas is added, the cause will be the air damper, more precisely, its condition: it clogged. Structurally, the part is located in the place where the resulting fuel is sprayed behind it, and, accordingly, the product collects all inclusions in low.quality gasoline. To eliminate the problem, you just need to clean it. The same situation can occur with a filter clogged, but it is eliminated similarly. Total, we specify the reasons for which the tool is led to the gas to the stalled state:

• a clogged air damper;
• The clogged filter is fuel, and when you give gas, this is especially noticeable;
• the air of the crankshaft shaft occurs;
• damaged gasket between the cylinder and the carb.

When you cleared, washed and blowing the elements, but again the lawn mower stall when you press the gas-replace them with new ones, check the quality of the fuel, as well as the literacy of the proportions of the cooked mixture. When opening the air damper, the tool will stall for the following reasons:

• Dosage carburetor.
• The appearance of cracks on the fuel hose caused air leaks.
• The occurrence of problems with the oil seals.

In the process, there are situations when the lawn mower at high speeds is subject to a similar sharp stop. It occurs for the following reasons:

• due to problems with the circulation of the fuel mixture;
• with air leaks;
• The fuel intake hose is poorly connected or cracked and cannot be used;
• stab or clogged the valve of the cover of the gasoline tank;
• The carburetor was resolved.

In most cases, nevertheless, the cause will be a carburetor and related filter, hoses. If you need cutting gear or trimmer heads, then our site will also offer them to buy them with gasoline tools and components for them.

Why is the lawn mower stall at idle

Users have repeatedly ask about stopping the braids for the grass “on hot”, that is, when the mechanism started, worked a little, and then took it. and stopped, stalled. The reasons for this situation are the following:

• problems with the carburetor damper;
• Gasoline in a carbe can even boil;
• If the ignition is damaged, then the trimmer for the grass will also heat up and stall.

In each of the situations, check the details for strength, and if they have already outlined their own, order new ones from specialists. We will call one of the most popular situations: the lawn mower stalls at idle. This happens for reasons:

• The carburetor was diluted himself, or was illiterately adjusted;
• the carburetor is contaminated;
• The air filter is very contaminated;
• The use of inappropriate fuel can cause a reduction in the gearbox revolutions;
• At idle, your trimmer for grass can stall if the throttle closed;
• Air fell into the carba system;
• The lawn mower receives a missing portion of gasoline to work fully, and therefore stalls.

We are sure that you received the maximum of useful information, and found a way out of your individual situation through our technical councils. Any spare parts, like a starter, motorcycles, its components and accessories are located at the lowest value in the country. Hurry up!

The trimmer for grass stalls. how to eliminate the problem

A gasoline trimmer for grass is a useful tool for cleaning from unnecessary grass of house territories and large area lawns. The design of this technique is quite complicated, therefore, if the device breaks, there may be several reasons. The most likely factors that have caught a breakdown are usually described in the user guide. Knowing why a trimmer for grass stalls, you can try to independently eliminate the defect. The most common malfunctions provoking the motorcycle stops, and the ability to repair them with your own hands is in the material further.

In order to most accurately determine the cause of the trimmer malfunction for grass of any brand (for example, echo) and find out the possibility of eliminating it, you need to install, when performing what action the device stalls. The engine can turn off both at idle and at high speeds, heated under load or immediately after starting and t.D.

If you stalled after gas supply

Owners of gasoline braids often mention that the lawn mower stalls when you press the gas. Usually such a breakdown occurs due to problems in the carburetor. A failure in his work can occur due to long-term storage, use in difficult conditions, significant overload of the motor. The symptom of such a breakdown will be vibrating movements of the device during operation.

On a note! Users familiar with the repair of a car carburetor can try to restore this important node of the trimmer for the grass on their own, using the instructions for operating. Otherwise, the correct decision will be to seek help from the service center representatives.

Sometimes a trimmer for grass stalls when you give gas because the fuel valve is clogged. This interferes with the supply of gasoline. To eliminate the problem, it is enough to loosen the valve. Thus, normal supply of carburetor fuel will be restored.

Another possible reason why the lawn mower stalls when gas is supplied is pollution of the soundtress (check valve). This detail prevents the appearance of a vacuum in a gas tank. If it is clogged, the air does not flow, which means that fuel does not go to the carburetor. To eliminate the problem, it is necessary to clean this element.

If it stalled at high speeds

If the carburetor stalls at high speeds, this means that in idle and small there are enough incoming fuel, and to work on high is not enough. Then it is necessary to check the serviceability of the following nodes of the trimmer for the grass.

• Fuel hose. its integrity could be violated as a result of cracking. In this case, you need to replace the part. Or maybe you just need to tighten the clamps.
• A filter network between a carburetor and a hose for supplying a gasoline mixture-it could clog. In this situation, it is necessary to clean the detail.
• The valve on the gas tank cover. he could stick or clog with garbage. Cleaning is also necessary.
• Carburetor. perhaps as a result of constant vibration, it was resolved. This is usually characteristic of cheap Chinese details. To eliminate the problem, it is necessary to set up according to the instructions. In some cases, it is enough to only weaken the tightening of the carburetor case. If the adjustment is not possible, it is necessary to install a new element.
• Additionally, check the air filter. Perhaps it will need to be washed and cleaned or replaced with a new one, as he could clog with dirt and particles of grass when tilted technology, when the user mowed in hard.to.reach places.

If you stalled during work idle

If the lawn mower stalls, working idle, there may be several factors reasons.

• First you need to check the prepared fuel solution, when it comes to a four-stroke trimmer working on a gasoline-oil mixture. There is a chance that it is made incorrectly. the proportions are not withstanded. Because of this, the gearbox is warming up, and the revolutions on the drum are lowering.
• Another probable cause is blockage of elements such as a throttle, air filter or carburetor. You need to clean the indicated details.
• Another possible factor is to resolve or incorrectly carried out carburetor adjustment. You need to adjust the setting according to the instructions.
• Observe this problem mono and when opening the air damper. In this situation, the lack of fuel for a trimmer for grass occurs through the fault of the air flow.

If the device does not have enough fuel, it works properly at high speeds or when they increase, but stalls at idle. If the root of the problem consists in the carburetor, the lawn mower will be disconnected both with cold startup and hot.

If you stalled after starting

If the technique starts and stalls immediately after starting, this indicates the wrong settings or deducting the device. As a result of this, the fuel enters the engine unevenly, which leads to significant vibration and disconnecting the trimmer for the grass. To fix the breakdown, it is necessary to reconfigure the device according to the user management.

Another probable problem is the blockage of the valve supplying the gasoline mixture. It must be cleaned.

On a note! If the trimmer for the grass starts, but immediately stalls, it may also mean that the fuel is moving to the carburetor with difficulty. Weakening the valve will help to eliminate the problem. this will provide uniform and free circulation of fuel in the device.

Another possible reason is the damaged fuel intake hose. Air can penetrate through cracks and holes into the system. To solve the problem, you need to increase the engine speed in order to get rid of air bubbles that have penetrated the device.

If you stalled when opening the damper

If the technique works properly at idle, but stalls when opening an air damper, this reports about the penetration of air into the system through cracks in the fuel supply hose or damaged oil seals. To fix the breakdown and establish the work of the tool without driving air from the atmosphere, it is necessary to replace damaged parts.

Preventive measures and operating rules

So that the lawn mower does not work and does not stall when starting, it must be correctly stored and operated. Compliance with the following simple recommendations will forget about problems.

• When begging the grass, you need to monitor the state of the cooling system. It is also necessary to regularly clean the channels in the case and starter’s ribs.
• To clean the tool, you should use kerosene, solvent, or other washing tools.
• You can not clean a hot tool. it must cool before washing.
• It is important to observe the recommended working mode. this will avoid overheating of the engine.
• If a braid for grass is not used over the next thirty days, the fuel must be drained, otherwise it will fall into heavy components that can score the channels of the carburetor.
• After the fuel is merged, the trimmer for the grass should work at idle for some time until it turns off. This will allow you to completely get rid of the rest inside the working mixture.

To store the tool in cold weather, you need:

• completely drain the fuel;
• disassemble the lawn mower, wash and clean all available components;

• inspect the condition of the parts, eliminate all defects that can be corrected;
• pour the required amount of oil into the gearbox;
• Clean the air filter;
• perform partial disassembly of the engine, wash all moving parts, blow and lubricate thoroughly;
• To lubricate the piston, unscrew the candle, then raise the piston to the upper dead point by the starter, pour a small amount of oil into the hole for the candle and do the crankshaft several times.

Important! If there is no way to store a trimmer for grass in a warm dry room, you must first wrap the motor with an embarrassed rag.

Only by observing these rules, you can be sure that the lawn mower will work properly and will not stall for a number of seasons.

As you can see, stopping the work of a trimmer for grass can be caused by many reasons. Most of them can be fixed independently using the user instructions. In cases where there is no self.confidence, the equipment is recommended to be attributed to repairs. It is worth remembering that incorrect actions can cause even greater harm to the trimmer. As a result, the repair of Motokos will cost a much larger amount than it would be initially, and in the worst case, it may be necessary to buy a new unit.

Why is a Chinese lawn mower not developing momentum ?

Chinese lawn mower Analog Husqvarna does not develop turnover, the reason was very simple (watch in the video)

Vibrations that take place in the process of operation of the lawn mower can lead to a reservoir.

Incorrect adjustment of the lawn mower can be fixed by simply adjusting it in accordance with the requirements specified in the operating instructions.

In addition, sometimes gasoline trimmers for grass can stall due to the fact that the valve located in the gas tank lid just clogged or sticks.

To find out, try using a braid by loosening the gas tank cover.

If in this mode the device works properly, clean the valve.

In this article we will consider the problem why the lawn mower stalls and how to deal with this problem.

Even very good motorcycles may have problems with the launch. For example, it starts and stalls. Most likely, this indicates problems with filters. air or fuel. If it stalls at idle, then, most likely, the motorcosa has problems with the carburetor, which is too fast overheated and no longer copes with the formation of a qualitatively air fuel mixture.

If a trimmer for grass stalls when you press gas, t.e., когда двигатель начинает работать на больших оборотах, то это свидетельствует о проблемах с карбюратором или с топливным фильтром.

Motokos with an air filter will be evidenced by the fact that it ceases to work when opening an air damper.

Note that the Well Part online store offers you for the widest assortment and at the best prices.

What to do if the lawn mower starts and stalls?

Now we will consider all the above problems described in more detail.

In principle, the reasons why the engine of motorcycles stops working when pressing gas can be a huge number. Here we will consider only the most common.

Perhaps the air damper just clogged. And to eliminate the problem, it will be enough to simply clean the air damper. The engine also stalls due to the clogged air filter. To clean it, the filter should first be washed in the solvent, and then blow the stream of compressed air.

A similar procedure should be carried out with the clogged fuel filter, which prevents the intake of the fuel in the proper volume with an increase in engine speed.

The engine can stall for other reasons. Firstly, the spacer is worn between the cylinder and the carburetor, and secondly, the crankshaft oil seals began to suck in air.

We have already indicated that in this case the problem is in the carburetor. In it, due to increased temperatures, gasoline begins to boil, which is why the air-fuel mixture ceases to form or its quality is critically reduced.

In addition, this problem may arise due to the fact that the carburetor is equipped with a rotary rather than a disk damper. If the problem has acquired a chronic character, then it should be solved radically. by buying a new carburetor with a disk barrier.

Most likely, access to the fuel tank is difficult or completely absent, which is why a reduced pressure zone is formed in it, due to which the engine stops receiving fuel in the required amount and because of this you stop working.

The engine at idle can stall for the following reasons:

News ONENEN ONENEN ONENY ONENY ONE ONE ONE

LSI and began to prepare not quite normal gasoline solution, which is why they began to fall on the drum;

You will need spare parts to eliminate most problems, and the Well Part will be ready to provide them with the best cost to you.

How to clean and store a tool?

During the operation of the lawn mower, monitor the state of the engine cooling system. The channels available in the starter housing, as well as the cylinder ribs, should always be clean. If you ignore this requirement and continue to operate the motorcycle, then you can disable the engine due to overheating.

Competent care of gasoline scythe during operation allows you to use it for several seasons in a row without serious repair

Before cleaning, let the engine cool down. Take a brush with a soft pile and clean the outer surface from dirt. Cleaning plastic parts is carried out by solvents, including kerosene, or special detergents.

After the summer season, the lawn mower should be prepared for long.term storage. To do this, the fuel mixture is drained from the tank. Then the engine is launched in order to develop fuel residues in a carburetor. The entire tool is well cleaned of pollution and sent to “hibernation”.

As you can see, it is possible to repair the malfunctions of the household lawn mowed on their own. Service services should be contacted in case of serious breakdowns. In this case, the cost of repairs with the price of a new lawn mower should be correlated. Perhaps it will be more advisable to buy a new tool.

What to do if a benzotrimer is not gaining momentum ?

If you once purchased a trimmer for grass, working with gasoline, then you probably had to face the problem of turning on a trimmer for grass, as well as a problem as a benzotrimer does not gain momentum.

That is why this article has been created.

So, what to do if a trimmer for grass, working for you for several years, suddenly just stops gaining momentum. and the motor is simply stalling? In this case, you and I should consider a number of problems related to stopping the work of the motor.

The motor may stall under various circumstances. I have the problem of the STIHL FS38 STIHL FS38. Sometimes the reason for the incorrect operation of the trimmer for grass working from gasoline is the clogging of the air filter.

It is the filter that is one of the most important reasons why the operation of a gasoline trimmer for grass may stop.

Various garbage very often gets into it, particles of dust that also clog the filter, so it needs to be cleaned and washed every month, and maybe more often, it all depends on what power the gasoline trimmer has for the grass, as well as then how often do you use this device.

Benesotrimer (Moto Mower) Carburetor repair does not work does not develop speed, loss of power

Chinese lawn mower Analog Husqvarna does not develop turnover, the reason was very simple (watch in the video)

If you have done operations with the filter, but the work of a trimmer for grass working from gasoline remains the same, the benzotrimer does not gain momentum what to do?

Then you should try to extract the filter from the device in order to provide the so.called “relief” of the trimmer for grass. Why is a Chinese lawn mower not developing speed, the cause of Husqvarna. Should help.

The next and rather common problem when working with a gasoline trimmer is that it simply stalls and does not give any signs of life.

In this case, the problem may be as follows:

The last and most common cause of the breakdown of a gasoline trimmer for grass is that the cable that is located in the carburetor department was just sleeping.

Therefore, make sure that it will be well pulled, but not to the limit, otherwise with too much load on the gasoline trimmer for grass, this small cable can crack and then you will definitely have to contact the service center, and then also throw out many money into the wind.

The Stihl 180 chainsaw does not develop turnover or if you released the gas trigger, it continues to work, without dropping the momentum in this case. These obstacles are quite all.prominent. Let’s try to understand the reasons for which the appearance of similar defects is. We will also then see how to conduct diagnostics if the chainsaw does not pull. Circus.

Oleo-Mac Speedgo Head Tutorial Mac 753 T Read more on the website of Oleo-MAC-755-Master/ ! OLEO-MAC 753 Lawn Machine Two Cylinder (cm. cube) 40.2 power (kW/l.With.) 1.6 / 2.2 weight (kg) 7.9 pipe diane (mm) 28 volume of the gas tank (l) 0.75.

When caring for a personal plot, summer residents periodically face the fact that the lawn mower is not started. There are many reasons for the refusal of the tool. For the correct diagnosis of the problem, the owner of the useful in the country’s dive must know the device and the principle of operation of its individual parts.

Since the gasoline trimmer for grass refers to complex devices, before starting work, it is necessary to carefully study the operating instructions. Very often it is simply ignored, or they get acquainted with it superficially. As a result, when the tool stalls or refuses to start, the question arises. “why the lawn mower is not started?»A long seasonal break in work, improper storage and untimely maintenance of a trimmer for grass, will deliver a lot of trouble to the summer resident, to eliminate the reasons.

Immediately after its beginning

The device may work immediately after starting, if the carburetor is displaced or incorrectly configured, this leads to uneven fuel supply. The result is that the device begins to vibrate clearly. To eliminate problems, the carburetor is reconfigured in accordance with the instructions to the mechanism.

In addition, the engine stops when the fuel supply valve clogs. In such cases, it is enough to clean it. If at first the lawn mower worked, and then immediately died out, perhaps the fuel hardly gets into the carburetor. The solution to the problem helps to weaken the valve, which provides free circulation of the mixture in the system.

The stop can also be caused by an air pump, if there is mechanical damage to the hose (holes, cracks) that form fuel. In this case, you need to add turns to the disk to quickly displace air bubbles from the system.

When heated

The lawn mower often stops when heated. At the same time, it begins, works “with jerks” and gradually stops. This process occurs when gasoline boils in a carburetor, or a damper has a rotary, not a discoid. In the latter case, the part changes.

It turns out that the trimmer for grass heats up if the spark plug wire is damaged. For the device to work normally, the parts are replaced.

Why and what to do if a trimmer stalls for grass

There are several reasons why the trimmer for grass stalls when the grass. Usually the problem is provoked:

• wear of engine elements. piston, bearings, crankcase;
• malfunctions with fuel supply. a carburetor can fail in the device, sometimes a malfunction causes a clogged filter;
• mechanical damage to hoses, tubes and cables;
• disobedience with the ignition chain.

Most often, under a load for one reason or another, an old trimmer for grass, which has long been in operation, stalls for a particular reason. But sometimes the owners of new gasoline devices face problems.

Why is a trimmer for grass stalling when pressing gas, increasing speed

If the trimmer for the grass stalls when you give gas, then the problem is usually a malfunction of the carburetor adjustment. The malfunction often occurs if the device was inaction for a long time, and then received a significant load. Sometimes the unit stalls immediately after increasing speed, if before that it was operated in difficult conditions with violation of the rules.

The following reasons are also leading to problems with the performance of the device:

With stretching or rupture of the fuel hose in a gasoline trimmer, the elements that have become unusable must be changed. If the reason is in the clogged valves and filters in the unit, they are quite simple to clean.

If the reason that the trimmer stalls for the grass is caused by problems with the carburetor, the problems are accompanied by vibrations

Another common problem is that the trimmer for grass stalls with increasing speed due. In this case, you need to find the instructions for the device and carry out the reconfiguration of the unit. Often it is enough to weaken the tightening of the carburetor body.

Why does a trimmer for grass stall at idle

Garden trimmer for grass often stalls even at idle. The reasons for the malfunction are usually simple. First of all, the improper adjustment of the carburetor affects performance. it leads to problems both at high speeds and in idle mode. Turning off the device can provoke clogging of an air filter or throttle.

Sometimes a trimmer for grass stalls if incorrect fuel is used for it. The gearbox for this reason overheats and reduces momentum.

If a malfunction occurs, it is necessary, first of all, to inspect the carburetor unit and perform mechanical repair or configuration. If the cause is of poor.quality fuel, you need to replace the mixture with a more suitable.

What to do if the trimmer for the grass starts and immediately stalls

If the trimmer for the grass does not gain momentum and stalls immediately after starting, the problem usually consists in improper tuning the carburetor. In this case, fuel in the system comes unevenly, the gasoline unit vibrates and cannot work normally. Repair consists in reconfiguring a carburetor unit according to the instructions from the manufacturer.

Engine stop causes fuel supply valve. The element must be carefully cleaned, and then installed back in place. If the lawn mower still stalls immediately after starting, perhaps the valve is too tight and it needs to be loosened. In this case, the fuel mixture will begin to circulate through the system freely, and problems with the performance of the unit will disappear.

In some cases, a gasoline trimmer for grass stalls due to the fact that the hose contains damage that pass the air. During the repair, you need to replace the fuel tube with a new.

Attention! If the damage in the hose is insignificant, it is allowed to simply add a revolution drive. This will allow you to drive out air bubbles from the fuel system.

What to do if the trimmer works and stalls for the grass

Owners of garden gasoline units are faced with the fact that a trimmer for grass stalls at large speeds after a short work. First, the device begins to function with jerks, and then gradually stops.

Typically, the reason is the overheating of the system. gasoline in the carburetor simply boils. A trimmer for grass can heat up if the ignition circuit coil or wire is damaged. There is no point in repairing worn details, they are simply changed to new working.

The use of a trimmer for the grass does not lead the use of not disk, but rotary damper in a carburetor

What to do if the trimmer for the grass overheats and stalls

If a hot trimmer stalls for grass, the situation is a great danger to the performance of the unit. Repair should be carried out immediately, otherwise the device will be completely unusable, and it will be more difficult to restore it.

Overheating of the unit usually cause the following reasons:

• The use of inalitions. pour fuel into the tank with precisely with such an octane number that is recommended by the manufacturer;
• a large amount of air in the system. for this reason, the enriched mixture releases an excess of heat;
• non.compliance with the proportions of oil and gasoline in the preparation of fuel;
• The thick layer of soot on the muffler. soot is a good heat.insulating material, the gasoline braid for the grass during operation is very hot and stalls;
• The displacement of the axis of the spit.headed head inside the bar. for this reason, the rotation slows down, and the load on the engine increases.

If the gasoline unit stalls, you need to carefully examine it and eliminate first of all possible deformations of the structure. Then it is necessary to study the fuel parameters. If they do not correspond to the recommended, gasoline is replaced with a more suitable. If unnecessary air gets into the system, it is necessary to independently or with the involvement of specialists to adjust the position of the carburetor damper.

Sometimes a gasoline trimmer for the grass overheats and stalls because there is too old fuel in the tank. Use a fresh mixture for the unit, which was stored no longer than two weeks.

Attention! A trimmer for grass will overheat if you use it for too long, or mow with a weak device hard thick grass.

How to avoid breakdowns

Many breakdowns of a gasoline trimmer for grass can really be eliminated if you remove the causes, but if possible, it is recommended to, in principle, avoid faults. Simple measures allow to maintain the unit in a working state:

• You need to use a trimmer for grass in accordance with the recommendations of the manufacturer. It is impossible to use a weak device for removing hard weeds on the site, it is also not recommended to use motorcycles in excess of the due time. The gasoline unit needs to be turned off regularly and allow it to cool down.
• During the operation of the device, it is necessary to monitor the state of the cooling system. To maintain performance, the channels in the case are regularly cleaned, like the starter’s ribs. The clogging of the system often becomes the reason that the unit stalls from overheating.
• After using the gasoline trimmer for the grass, too, you need to clean. In this case, the procedure is not carried out for a hot unit, at first it must completely cool. For cleaning, use solvents, kerosene and other products allowed for use by the manufacturer.
• Before cleaning, the motorcycles for storage must be drained from the tank, the remains of unused fuel. If this is not done, the gasoline mixture will fall into heavy components and will clog the channels of the carburetor, which will subsequently cause malfunctions. After draining the fuel, the device is launched at idle and waited for it to turn off.

With the onset of autumn, a gasoline trimmer for grass must be correctly removed for storage. First, the residues of the fuel mixture are drained from the device, and then the unit is disassembled, rinse and clean all removable components.

Before harvesting gasoline motorcycles for storage, you need to evaluate the condition of its parts, carry out the necessary repair and replacement of nodes. Air filter needs to be cleaned. The engine is partially disassembled, rinsed and blown by moving elements, and then applied a new grease. To maintain the piston part, the candle is unscrewed and the piston itself is lifted to the top point, and a little oil is poured into the opening opening and the crankshaft is twisted several times.

Store a gasoline trimmer for grass in winter is necessary in a warm room

Problems without repair

If the electric motor does not reach the desired mode, then it will not work to squeeze the linen. But do not panic. try to find out the reason for the unstable operation of the Washing Motor Motor.

First check if the “revolution adjustment” button is pressed. Most cars have such a function present. If you have chosen a delicate washing program. then the squeezing mode will be similar.

In some cases, it is not possible to dial the required number of revolutions from the engine from the washing machine for the following reasons:

• The washing machine is overloaded.
• Too little underwear in the drum. In some products, a minimum weight sensor is installed, which does not start the squeeze with a low amount of clothing in the tank. Add a large terry towel, and the process will go according to the debugged scheme.
• Sometimes an imbalance occurs. For example, when a lot of small things got into a duvetail. In this case, distribute all the underwear evenly and repeat the seas.
• Low voltage. For the “squeezm” mode, the machine engine must gain high speed than when washing, therefore, energy is required more.
• The washing program is incorrectly installed. Check, a mode without spin or delicate mode can be selected.

Many home craftsmen are interested in the question: how to adjust the engine speed from the washing machine, if this function is absent in the control, and how much the speed of rotation can be reduced.

Attention! To reduce, even slightly, the existing parameters of engine speed from the washing machine is strictly prohibited.

Specialists from the service center, who have special equipment for repairing washing machines, will be able to lower such parameters. If the speed is reduced independently, then this can lead to serious problems with further operation.

What to do if the washing machine does not gain the necessary revolutions in squirrel squeeze mode

Unfortunately, even reliable products from well.known manufacturers sometimes give out serious malfunctions. Among them, there is often a case when a washing machine does not gain momentum when spinning. Before you seek help from specialists, you need to find out the cause of the problem, and try to eliminate it on your own.

Most often, the causes of the poor speed of the washing machine during the squeezing may be the following.

If the device is not gaining momentum during spin, and the engine begins to spark, then the problem can be associated with wear of the motor brushes. When they are too abridged, contact with the collector becomes bad, and as a result, sparking begins. Because of this, the motor does not master the rotation of the drum in spin mode. As a result, the machine cannot gain normal turns. Fixing the situation is quite easy. just replace the brushes.

If the machine is rattling during the pressing, and the drum rubs against the case, then this may be associated with a malfunction of the bearing. If the oil seals lose tightness, then water may fall into it. The more the bearing is destroyed, the stronger the technique begins to rattle. In addition, it starts worse and worse to gain momentum in rotation mode until it completely fails. To correct the malfunction, it is necessary to replace the oil seals and bearing.

In the pressing mode, the typewriter does not have enough power to promote the drum. At the same time, the smell of pale rubber begins to feel. This may be due to the fact that the drive belt during operation stretched out and began to slip at high speeds. Because of this, the machine cannot promote the drum in spin mode. To eliminate the problem, it is necessary to replace the belt.

The machine during the washing reached the spin regime, but could not gain momentum for it. There can be several causes of the malfunction. Firstly, you should pay attention to the tachogenerator. If it is faulty, then the machine is lost control of the speed of rotation of the drum. If the reason is this, then you will have to replace the tachogenerator.

The second reason for the malfunction may be a level sensor. press. He is responsible for monitoring the water level in the tank of the machine and determines when you can turn on the drain or squeezing mode. If the press-steast is faulty, then the system thinks that the water is still in the tank, so the pressing mode cannot begin. To correct the malfunction in the worst case, you will have to replace the sensor. In addition, you can try to blow the sensor tubes, replace the press start hose or clean the pressure chamber of pressure.

Thus, if the machine began to make noise during operation, it is first necessary to determine the cause of the malfunction, and after that start repairing the equipment.