The correct first start-up and running-in of the lawn mowers are very important steps in the start of operation of a new tool. On the one hand, they make it possible to preserve the motor resource of the gasoline engine laid down by the manufacturer, since at this stage grinding of moving units and parts takes place. On the other hand, the first necessary skills for working with a trimmer are acquired, if we are talking about the first tool in my life.
Preparing for the first launch of the lawn mowers
Before you start the first start of the lawn mowing you need to perform a series of sequential actions:
- Inspect the gearbox and grease it;
- Prepare the correct fuel mixture.
We recommend that you perform them not only when buying a new trimmer, but also when preparing an old tool for the new season after storage.
Inspection and lubrication of the lawn mowing gear
Checking the gearbox before starting the gas trimmer must be done on a regular basis. The absence of lubricant or its small amount increases the friction of the gear transmission of the gearbox operating at rather high speeds. As a result, overheating and gears occur. The lawnmow reducer fails. Prevent the occurrence of such damage during operation and helps regular inspection.
If, before starting the gas spit, an insufficient amount of lubricant in the gearbox or its absence is detected, “LITOL” is put into the housing. To do this, it is necessary to unscrew the screw on the bend of the gear housing and syringe “LITOL” in the amount of 1-2 ml.
When working with a gas trimmer for a long time, add grease to the boom reducer every 8-10 hours.
Preparing the right fuel mixture
Before you start running in a new lawn mowing engine, you must also properly prepare the fuel mixture. As you know for two-stroke engines, it is prepared from special two-stroke oil and gasoline, taken in certain proportions. You can find out the proportions from the instructions that came with the tool or on the lubricant label. From the instructions you will also find out the recommended type of fuel, as well as the recommended type of engine oil.
Prepare fuel in small quantities sufficient for one mowing of grass. Use special plastic canisters for fuel, or separate glass or metal utensils. Oil is best filled with a medical syringe.
Video: First Lawn Mowing And Running
Going to run in a new lawn mowers, many are faced with the problem of preparing the fuel mixture. And the reason for this disagreement in the instructions of the manufacturer of the tool and in the instructions of the manufacturer of motor oils. The former recommend a proportion of 1:25. The second recommend 1:50. Who to believe? How to proceed?
According to experts, if in the instructions for the lawn mowers the manufacturers write the proportion 1:25 or 1:30, then most likely this is either a cheap tool with poor cooling, or the manufacturer does not know which oil the consumer will add. But here it must be understood that an excess of lubricant does not affect the performance of the trimmer in the best way. Excess oil does not completely fade during engine operation. It cokes, clogs the cylinder and piston.
What to do in this situation when running a new tool? An ideal option would be to buy exactly the oil that is recommended by the manufacturer of lawn mowers. In the case of run-in motors, when it is not possible to purchase the recommended oil, it is best to purchase a good Husqvarna two-stroke oil for the gasoline tool of the same name. It is not cheap, but it lasts for a long time. It must be disturbed as described in the instructions on the bank.
Remember, it is best to use the proportion that the oil producer gives. But whether the proportion that is written on the braid is suitable, it is better to find out by experiment. If, at the proportions recommended by the manufacturer of the trimmer, the engine sniffs with oil and smudges are visible on it, then the proportion needs to be increased.
First Trimmer Trigger
When everything is checked and the prepared fuel mixture is poured into the tank, the time comes for the first start of the trimmer before it is run-in. To do this, perform the following manipulations:
- Place the lawn mow on a flat horizontal surface;
- Move the choke control lever to the closed position;
- We pump up a few strokes of the primer fuel into the carburetor;
- Turn on the ignition toggle switch;
- Gently pull the starter cord until you feel resistance;
- After that, make a cord 3. 4 sharp jerks until the lawn mowing starts;
- After starting, open the air damper.
If the first time the lawn mowing does not start or stalls, slightly open the air damper on the carburetor and try to start again.
Getting Started Running Lawn Mowers
After starting, do not rush to run the trimmer immediately. Allow the engine to idle for about 5 minutes. While warming up, adjust the choke lever with the choke lever so that the spool with fishing line or knife does not rotate. As soon as the tool warms up, we completely open the air supply by transferring the corresponding lever to the “ON” position and squeeze the gas trigger by 1/2 and hold for 20. 30 seconds. Then we dump the gas, let the trimmer work for XX for 30.40 seconds. In this mode, we continue for 10. 15 minutes. Then we muffle and let rest 15. 20 minutes.
Having cooled the lawn mowing, we continue to run the engine according to the previous scheme. Start on a hot, trimmer must already have an open air damper. Try not to hold gas for a long time, as the moving parts of the tool only rub against each other. And do not let the engine idle for a long time as it can overheat.
The next stage is the running-in of the gasoline braid gearbox. To do this, select a site with soft young grass. We mow 5. 10 minutes with pre-gas for 1/2. 2/3 of the full throttle. After we take a break for 20. 25 minutes. The cycle is repeated 3. 4 times.
In general, running the lawn mowers according to the described algorithm is performed until the fuel mixture is fully developed in the tank. After which the tool is ready for continuous operation. In the process, monitor the temperature conditions of the gearbox and motor. They should not overheat.