Gas tank cover of motorcycles does not pass air. Stihl 180 chainsaw stalls when you press gas

Sapun on a gas station what is and where it is

To begin with, let’s figure out how to find out that the soundtress is faulty and needs to be cleaned or replaced. This can be done in three ways.

How To Fix a ChainSaw if You Put Oil in the Gas Tank

  • The first method examines the inspection of the condition of the hole on the gas tank cover. If the hole is clogged with dirt, then the valve definitely needs to be cleaned.
  • The second method is if the lawn mower does not start or the engine stalls after short operation. These are indirect signs that the carburetor cannot pump fuel into the system due to the current pressure inside the tank.
  • The third way is to disconnect the fuel hose from the carburetor, and then see. If the fuel flows with a strong stream, then the equalizer is working and does not need to be repaired. If the fuel does not flow or flows with a weak stream, then this indicates a malfunction of the equalization valve. Fuel does not proceed due to the pressure created inside.

To make sure that the problem is hidden in the saapun is quite simple. for this, try to unscrew the lid. If you do this with difficulty, and when turning the hatch, the sound of air is heard, then it is definitely worthwhile to clean the bacon.

You can clean the check valve in the following ways:

  • Use a needle and compressor. A needle is needed in order to remove dirt from the hole in the tank cover. Clusted air from the compressor must be blown out from the reverse side so that the remains of the dirt fly out of the hole. This method is simple, but it is not always suitable
  • Disassemble the bacon and examine with subsequent cleaning or replacement of the device. The offset of the cabin is not sold, therefore, in case of damage to the filter element or valve itself (usually it is presented in the form of a rubber seal), you will need to buy a new gas tank cover for its tool model

Below is an instruction on how to disassemble the saapun and clean it with your own hands:

  • The first thing you need to make sure that the soundtrack is in the tank cover. Next, consider the case when the check valve is located in the design of the cover
  • Remove the latch from the lid, which serves to prevent Luke’s loss during the refueling of the tool
  • We proceed to extract an equalizer of pressure from the inside of the lid. To do this, you need to lift the device, and extract with the rubber seal
  • Eliminated parts from the cover are a rubber gasket and a filter saopan
  • Next, it is necessary to remove the filter from the rubber valve, and clean and purge
  • If the rubber valve has no signs of damage, then it is enough to blow and clean it with the filter, and then build the device

The repair procedure has been completed on this, and it remains to verify the performance of the lawn mower saop in action.

Summing up, it should be noted that this small detail is often the reason that it is impossible to start a chainsaw. Even complete cleaning of the carburetor will not help to eliminate this problem. Often inexperienced mowers turn to service centers for the repair of the tool, not realizing that the reason is hidden in this small in size of the part, which plays a very large role in the operation of the gas instrumentation engine.

Publications

How to choose oil for chainsaws. useful recommendations

tank, cover, motorcycles, does, pass

How correctly the chain on the chainsaws and the features of the process are shortened

What is the difference between a two.stroke engine and what is 4MIX and 2MIX

Device and principle of operation of the chainsaw and its individual mechanisms

Where is the saapun on the trimmer of different tool manufacturers

Knowing what is a benzocosa or a trimmer’s saapun, you need to deal with the place of its location. Based on what the check valve is intended for, we can conclude that it is located directly in the design of the gasoline tank. On trimmers of different manufacturers, the check valve is in different places. The most popular location of the device is on the gas tank cover. However, the part can be located not only on the lid, but in the design of the gas tank. It all depends on the manufacturer of the tool. Trimmers for grass and lawn mowers of production of Stihl and Husqvarna have a saepun, which is located on the gas tank cover. The photo below shows what the soundtrack looks like.

Less commonly, the check valve is in the wall of the gas tank. This location can be found on outdated models of gasosos and chainsaws, as shown in the photo below.

Understanding the principle of work and the appointment of a sapun, it will not be difficult to find it on your own on your tool.

It is interesting!The location of the cabin on the gas tank cover is made specifically so that when it clogs or malfunctions, it was easy to replace.

tank, cover, motorcycles, does, pass

How to clean a saapun on a trimmer

The gasoline trimmer for the grass broke? Do.it.yourself repair is possible!

Gasoline trimmers for grass are completely indispensable in the elimination of weed thickets in the backyard, as well as when harvesting hay. Yes, as a grandfather’s “Lithuanian” they also showed themselves indispensable assistants. There is only one problem: even ancient braids for grass after the season had to be repaired.

What to do in the case when the gasoline trimmer for the grass broke? Repair in a service center. pleasure is not cheap. Is there a chance to somehow correct the situation on their own?

What should not be done

It is known that prevention is much preferable to treatment, and therefore do not forget to care for the instrument so that he does not need repairs. First of all, every 15 minutes of work should be given to the device for at least ten minutes of rest. In addition, you do not need to mow the grass above the one indicated in the instructions for operation.

If prevention has not helped

You may also like

tank, cover, motorcycles, does, pass

Babble 351 Partner. A worthy representative of the home network of chainsaws from the Partner brand. In its technical capabilities, it is focused on gardening and simple tasks to saw wood. Simplicity of design, ease of operation and service.

This material was prepared taking into account the practical experience of the pre-sale and warranty repair of the LCD TVs, mainly the Chinese category without name, including the so-called “clashes”. TV / DVD. In addition, the author used the material.

Before we begin to understand how to plow with a plow, we need to prepare a plow for plowing: 1. To get started, move the motor unit (even) to a flat position in your area. 2. Prepare mud hooks and interchangeable axes. 3. Replace the wheels with pedestrian.

Trimmer for grass gasoline Huter GGT-1000s author: Tehnostudio published: September 2, 2013 Vespers: 32,379 Mon I liked it: 31mn did not like it: 16online store: gasoline 1000S designed to maintain a lawn in a well-groomed form. Equipped with 2-stroke.

Bosch Rotak 37 Li How to change a knife to the lawn mower: Vladimir Yankova.published: June 16, 2017 Vespers: 5.363k about me: 19 MNO did not like: 0bosch Rotak 37 LI How to change a knife with YouTube lawn: Replace knife #Replace the bottom of.

Round-saw machines TOP-10. Circular hand.saw. Price, characteristics, comparison, buy auto.author: channel Baumarket UAODURED: August 31, 2015.Views: 45,766m I liked it: 58mn did not like it: 98 Coons of our rating is supplemented by the video “Cru.

What to do if the gasoline trimmer for grass still broke? DIY repair. a good option! Immediately make a reservation that we will tell more about the malfunctions of the engine, since almost everyone will be able to fix the broken barbell. In extreme cases, it can simply be fixed with some tire and clamps.

Ignition

So, if there are problems with the fact that the tool does not start or stalls immediately after the start of work, first you need to pay attention to the state of the ignition system. Try to turn out the candle and inspect it. In the case when the device is completely dry, something probably happened with the supply of the fuel mixture.

Small, yes remote. How to clean the muffler on the trimmer Husqvarna 128 r, very often the problem of power loss lies on the surface and people without knowing it are trying to change the carburetor to Khuskvvvvnu Bun. A plug of a gas tank of a Chinese lawn mower, which can bring a serious problem!

We disassemble and clean the ventilation of the crankcase gases of VAZ classics, cleaning tips, tips.

Fuel tank check valve

Even more information about the repair and choice of tools on our website www.Looktool.Ru, we are happy for everyone.

The candle is wet? Fully “thrown” with gasoline-oil mixture? Your gasoline trimmer for the grass, the repair of which we are trying to describe, has problems with carburetor adjustments. This often happens when non.specialists tried. If you have no experience, we strongly advise you to contact the service center, since you can well burn the entire piston system with your actions.

You may also like

The coil of the trimmer for the grass mows grass, but it wears out and often needs to be replaced. Recently, motorcycle or electric braids have become widespread. The main working element of such a garden tool is turns covered.

Living hedges and neatly trimmed bushes create a cozy atmosphere on the site. To maintain a given form, gardeners must constantly cut off the branches. If thin and soft branches are most often used with a secateur, for a more global st.

With the advent of the summer of many owners of personal plots, the question is disturbed by a knitted for the purpose of putting a knife on a trimmer for grass. Two or more burning questions are why and when it is targeted to replace the fishing line for a trimmer on a motorcade with a stronger cutting.

In every summer village, village, suburbs and in the town itself, these devices come across: they work outly, aligning lawn grass, cleansing the place of squares and parks, gardens and gardens from thickets of burdock, wormwood and weeds. Noise and crack from trim.

Overview of a gasoline trimmer for the grass Patriot PT 45555SATOR: Vseinstrumentiruuroed: July 5, 2017.Views: 6.524 Mne I liked it: 23 mm did not like it: ONEGROURE OF VISITURE. Gasoline trimmer for grass with an indiscriminate arrow Patriot Pt 4555ES Country 250108045 Sweet.

How to dilute gasoline with oil for a trimmer for grass?Technical conditions for a trimmer for grass contain links to recommended combustible materials. With all this, the octane number of gasoline brand is indicated specific, but in terms of oils there is an extensive explanation about the need to use.

However, not everything is so bad: if you violate the rules of cold launch, trying to pump up the fuel mixture all the time, then this can easily lead to throwing.

It is another matter when the candle is covered with a thick layer of black car. In this case, the gasoline trimmer for the grass, the repair of which we describe, exposed to poor.quality fuel mixture. Maybe the matter is again in the wrong adjustment of the carburetor, which gives out too rich the fuel mixture. Just replace the candle.

Often, the absence of gasoline entry into the combustion chamber is explained by the fact that a lot of dirt has accumulated in the gas tank, which simply clogged the feed hose. as shown on the cleaning of the bacon how to repair the starter on the trimmer. Disconnect the fuel hose. If fuel does not flow from it, then the clogged fuel filter or a saopan is to blame. The latter can be cleaned with a needle, and the first is advisable to completely change every three months.

Install a bench.tank barbell

The need to study the device of a lawn mower occurs when the first breakdowns occur. These breakdowns arise in any case, regardless of who is the manufacturer of the tool. Motokos malfunctions can be divided into two categories. simple and complex, requiring the replacement of parts or mechanisms. Simple types of breakdowns include a malfunction of a benzocos. It is about this device that on the trimmers will be discussed in the material.

What is a sapun and why it is needed on a trimmer

The fact of the trimmer is, and why it is intended, far from many experienced kosari and instrument owners know. What is it, and how the detail affects the work of the lawn mower, it’s time to figure it out. Before you understand the question of what is called a benzokos as a benzocosa, it should be noted that this part has a direct impact on the launch of the tool engine.

The cabin is called the valve that passes the air in one direction. This part is called a check valve, through which the pressure in a closed container occurs. This tank on a gas tank is a fuel tank. Why do you need to balance the pressure in the tank of the lawn mower, and how the check valve affects the operation of the tool engine?

To understand the purpose of the check valve on a gas station, we will briefly consider the features of fuel supply to the carburetor.

  • The fuel poured into the tank is sucked into the carburetor during engine operation. For this, the tank has a hose that is connected to a carburetor
  • The membrane, which, by creating a vacuum, absorbs its absorption, is responsible for the pumping of the fuel from the tank to the carburetor
  • When operating the engine, a gradual devastation of the tank occurs, and since the tank is a completely tight container, in the process of reducing the fuel, a vacuum or vacuum is created
  • The higher the vacuum (grows with a decrease in the amount of fuel in the tank), the more difficult it is for the carburetor to pump fuel
  • To eliminate the effect of the vacuum in the gas mushroom tank, a check valve is used, which passes the air in one direction, and does not allow fuel to flow out

The sapun is aligned with the pressure of the trimmer for the grass in the gas tank, and if this part is malfunction, the engine starts up. This difficulty is that the carburetor membrane simply does not have the opportunity to suck fuel due to the vacuum formed inside the container. The check valve works as follows:

  • When creating pressure inside the tank, air leaks occurs, thereby the vacuum decreases
  • Air leakage into the tank when the chainsaw is operating excludes the flow of the fuel mixture from the tank

Where is the saapun on the trimmer of different tool manufacturers

Knowing what is a benzocosa or a trimmer’s saapun, you need to deal with the place of its location. Based on what the check valve is intended for, we can conclude that it is located directly in the design of the gasoline tank. On trimmers of different manufacturers, the check valve is in different places. The most popular location of the device is on the gas tank cover. However, the part can be located not only on the lid, but in the design of the gas tank. It all depends on the manufacturer of the tool. Trimmers for grass and lawn mowers of production of Stihl and Husqvarna have a saepun, which is located on the gas tank cover. The photo below shows what the soundtrack looks like.

Less commonly, the check valve is in the wall of the gas tank. This location can be found on outdated models of gasosos and chainsaws, as shown in the photo below.

Understanding the principle of work and the appointment of a sapun, it will not be difficult to find it on your own on your tool.

How to clean the check valve and restore the tools of the tool

To begin with, let’s figure out how to find out that the soundtress is faulty and needs to be cleaned or replaced. This can be done in three ways.

  • The first method provides for inspection of the condition of the hole on the gas tank cover. If the hole is clogged with dirt, then the valve definitely needs to be cleaned.
  • The second method is if the lawn mower does not start or the engine stalls after short operation. These are indirect signs that the carburetor cannot pump fuel into the system due to the current pressure inside the tank.
  • The third way is to disconnect the fuel hose from the carburetor, and then see. If the fuel flows with a strong stream, then the equalizer is working and does not need to be repaired. If the fuel does not flow or flows with a weak stream, then this indicates a malfunction of the equalization valve. Fuel does not proceed due to the pressure created inside.

To make sure that the problem is hidden in the saapun is quite simple. for this, try to unscrew the lid. If you do this with difficulty, and when turning the hatch, the sound of air is heard, then it is definitely worthwhile to clean the bacon.

You can clean the check valve in the following ways:

  • Use a needle and compressor. A needle is needed in order to remove dirt from the hole in the tank cover. Clusted air from the compressor must be blown out from the reverse side so that the remains of the dirt fly out of the hole. This method is simple, but it is not always suitable
  • Disassemble the bacon and examine with subsequent cleaning or replacement of the device. The offset of the cabin is not sold, therefore, in case of damage to the filter element or valve itself (usually it is presented in the form of a rubber seal), you will need to buy a new gas tank cover for its tool model

Primary lamp (pear)

The primer lamp supplies fuel through the fuelboard to the carburetor. This allows you to facilitate the cold start of the engine. You need to click on it only twice. When the rubber dries, it can crack, which will lead to fuel leakage.

Check the flask flask for tight. This is easy to do, a simple visual examination is enough. If you feel the smell of fuel or see that fuel is dripping from the light bulb, replace it. He can also suck air if he cracked, which affects the ratio of fuel and air in the carburetor. To replace it, just remove it with pliers.

  • Clean the body;
  • Put on a new clamp on the pear so that the protrusions are directed out;
  • Insert it into the case and carefully tap it with a rubber hammer;
  • Make sure that the metal clamp is as far as possible from the lamp, without damaging it;

Fuel tank

A crack in the fuel tank causes a leak. Leaks. Frequent phenomenon in the seams. If you notice a leak or wet and smelly fuel, replace the tank.

First, drain everything from the tank, then disconnect the fuel lines. On some models, the removal of fuel lines may vary: some are attached outside, others pass through the sleeve into the tank. Remove all screws or clamps holding the tank in place and install a new tank. Then the fuel should be added.

Fuel tank

A crack in the fuel tank causes a leak. Leaks. this is a common occurrence in the seams. If you notice a leak or any damp and felt the smell of fuel, replace the tank.

First, drain everything from the tank, then remove the fuel lines. Removing fuel lines may differ on some models: some are attached outside, while others pass through the sleeve into the tank. Remove all the bolts or clamps holding the tank in place and collect a new tank. Then share the fuel.

Fuel cap

The gas tank cover prevents fuel leakage and pollutants entering the tank. Leaks can be caused by a crack in the lid due to vibration, as well as a worn sealing ring. You can simply replace the gas tank cover, or if you suspect that this is a problem with a sealing ring, you can remove the sealing ring using a small screwdriver and install a new exactly the same size.

The sleeve provides a seal for the fuel and the ventilation line for entering the tank. A quick visual inspection will show whether the sleeve flows. Over time, fuel eats a rubber sleeve, and you will need to replace it. If you notice a leak or feel damp around the sleeve, replace it.

Engine malfunctions

In most cases, subsequent shortcomings are observed in the work of the motor:

In order to find the cause of the problem, it is necessary to analyze the likely prerequisites in order by the way to exclude. Let’s go through this chain so that you know how to find a deficiency in a chainsaw in case of its occurrence.

A small amount of oil mixed with gasoline leads to increased wear of the cylinder.piston group. An excess of oil in the mixture, although not so fatal, is also harmful. Cooking piston rings, rapid formation of soot in the combustion chamber, and a drop in engine power may occur. In addition, the mesh screen of the muffler is closed. Therefore, some users (after the end of the warranty period for a trimmer for grass) recommend it to be dismantled.

Gasoline used in motorcycles. AI 92. The brand of gasoline is accurately prescribed in the operating instructions. Do not try to “force” the engine, filling the 95th gasoline into it. This can lead to overheating, unstable work of a trimmer for grass and breakdown.

It is not recommended to leave fuel in a trimmer tank for grass with a long break in operation. It is better to finish the working day by completely developing the entire mixture. If this is not done, then because gasoline from the engine will evaporate during the night, and the thin oil filter will remain, carburetor jacks may clog. This will cause difficulties the next engine start.

It is also necessary to observe safety precautions when storing fuel. Many pour gasoline into a plastic bottle of water. Is it worth doing so?

After several jerks, he will start and stall, which is a normal phenomenon. What to do when the fuel was definitely normal, there is a spark, but a trimmer for grass does not start a gasoline? Putting the damper to the working position, start the tool again and start working.

Any manufacturer of a benzo.tool first always suggests familiarizing in detail the operating instructions attached to a chainsaw or a chainsaw. Basically, the whole process of launch and further work with a benzo tool is painted there. Sometimes it doesn’t help, then let’s try to solve this problem together.

When buying in the right store of gas technology, you can tell you everything in detail about the launch and work of the gas tool, as well as demonstrate it in practice. If this was not, then it was a hypermarket or you were served by yesterday’s schoolboy or student. our congratulations!

Cold start.up engine. set the air damper lever (switch) to the “damper” closed “. We pump up the mixture in the carburetor in the presence of a fuel pumping pump (primer). Expand the starting handle (launching cord of the starter) to the tangible resistance of the engine, then pull vigorously (according to the amplitude with your hand to the chest).

2-5 such movements and the engine should start and stall-usually it happens. If this did not happen, further, as in the case of a successful first launch, we still transfer the air damper lever to the position of half.gas or even to the working position. And continue the institution in this mode by the same movements (1-4 times).

And finally, some gas.tools have a regular keying switch, just look at whether it was turned on.

New chainsaw or benzotrimmer (lawn mower) may not start.

All the reasons why the lawn mower is not started can be classified by the specifics of the operation of individual units. In the service center, the malfunctions are classified:

  • engine malfunction (piston wear, bearing malfunction, crankcase crack);
  • Fuel mixture malfunction. clogged pores of an air filter or a malfunction of a carburetor;
  • the ignition system does not work;
  • A mechanical malfunction. a leak of hoses, broken wires under the braid, rupture of the tubes.

The user first needs to check if there is a fuel in the tank. Start the launch in accordance with the instructions, putting the saw on the side. Set the air damper to the position “closed”, pump up fuel, turn on the ignition and produce 3-4 sharp jerks by the starter. If the engine has earned, open the air damper. The lawn mower is not started. we repeat the operations with a slightly open air damper.

With a unsuccessful launch, we begin to look for the reason for the refusal:

  • check the quality of fuel;
  • make sure that the candle and clean canal is working;
  • check the cleanliness of the air filter;
  • Make sure that the fuel filter is not clogged;
  • Check the cleanliness of the bastard;
  • Clean the exhaust channel.

complex reasons will be detected in the diagnosis of a malfunction, leading to the overhaul of the carburetor. Such reasons include clogging of the internal channels of the carburetor, wear on it gaskets and violation of the tightness of internal halls with a vacuum loss. DIY lawn mowing repair, if it does not start, will require patience.

Where to start the diagnosis of malfunctions if a trimmer is not started for grass? In situations where the tool stalls immediately after starting, it is worth examining the following units:

It is the breakdown of the above locations that most often leads to the fact that a trimmer for grass is poorly started. Let’s look at how to eliminate such troubles.

  • To twist the candle. Wipe it thoroughly, and then dry it.
  • Drain excess fuel in the chamber through the corresponding candle hole.
  • Clear the old candle if there is a dozen on its surface. Cope with the task will allow the use of a conventional ladies’ nail file or file.
  • When installing the element in place, set a gap of 1 mm. To check the parameter, it is enough to place any coin in the lumen.
  • Collect a functional block back.
  • Try to start a trimmer for grass.

It is recommended to perform a candle channel to dry for at least half an hour. However, in no case should you resort to the calcination of its elements. After all, heating the spark plug can lead to its final corruption. Что предпринять, если обслуживание функционального блока было выполнено в соответствии вышеуказанным рекомендациям, но триммер для травы не заводится, искра есть при этом?

In this case, it should be treated with gasoline threaded connection. The latter does not need to be saturated abundantly fuel. It should only be slightly moisturized. Resort to such actions should be to ensure the ignition. After all, no matter how much the candle gives a strong spark, in an absolutely dry chamber there simply will not be something to ignite.

If even in this case a trimmer for grass does not start, it is worth evaluating the quality of the contact between the high.voltage wire and the candle. In the absence of a spark (in the presence of a reliable connection between the indicated elements), most likely, the problem is caused by breakdown of the ignition unit. In this situation, you will have to turn to the services of masters who will reinstall the knot.

The stable functioning of a trimmer for grass can be impaired as a result of laying dirt in the graduation canal or the formation of a blockage on a muffler grid. This problem most often occurs during the operation of older generation trimmers. The issue is being solved by dismantling the anti.diploma mesh and its cleaning.

Electric trimmer for grass vibrates

Many mowing users noticed that some time after the start of the apparatus, it begins to vibrate very much. On some trimmers, mainly in models more expensive, an anti.vibration system was installed in the form of shock absorbers seized between the engine and the bar. But in some cases, even she does not save from strong vibration. The reason that strong vibration appears in the trimmer, there may be a small amount or complete absence of lubrication on a hard or flexible shaft located inside the rod of the apparatus.

Replacing the lubrication of the hard shaft is as follows:

  • Apply a small amount of lubrication to the shaft and evenly smear it along the entire length of the part, including the slots at the ends of the rod (if they worked, the shaft will have to be replaced);
  • After lubrication, insert the shaft back into the bar and put the gearbox in the same place.

The lubrication of the flexible shaft is as follows:

  • unscrew and remove the mowing head;
  • remove the bar from the electric motor by unscrewing a couple of bolts;
  • Pull out a flexible cable from the bar;
  • Lubricate the cable with grease along the entire length.

This is done like this: first you need to lubricate the end of the cable, and then insert it into the bar, after which, as it moves into the pipe, you should apply grease to the part and evenly distribute it on the surface. Then insert a bar with a flexible shaft into an electric engine and fix it.

In the event that the lubricant did not help, and the vibration continues to appear, you will need to change the flexible shaft.

The trimmer for the grass is very hot

Overheating of a trimmer for grass can occur for many reasons:

  • Gasoline has not the same octane number indicated in the instructions for the unit;
  • the proportions of gasoline and oil during the preparation of the fuel mixture are not observed;
  • A mixture of fuel with butter has long been prepared (the mixture cannot be stored for more than 2 weeks);
  • The trimmer for the grass works more than the time instructions;
  • A low.power trimmer for grass on thick and hard grass is used, the device works with overload and quickly heats up;
  • shifted towards the bar or the cassette lid clutched.

The latter occurs if you install a mowing head inappropriate for this unit, or when the axis shifts inside the bar. These changes make it difficult to rotate, the load on the engine increases, and it overheating.

Repairing lawn mowers with your own hands Video in the rogue cork comes out air

If the braid is turned over, then gasoline flows from this hole in the lid, but it seems to me a factory hole, but it gets in the way that gasoline flows from it, what should I do ?

Eduard shut when you turn it over, not for a long time, otherwise it will die out, and why? Think yourself.

Nadezhda a hole is needed for the cultivation and removal of fuel fumes that arise in the tank.

Andrey, as the gasoline is generated in the tank, a hole is created in the tank. The air is soupler the air is absorbed, as the volume decreases, you will be gasoline. The engine will stall after a while.

Tamara is still not a hole, but a hole. In order not to create a vacuum that will prevent fuel supply to the carburetor.

Jeanne and what to do if it flows from this hole? and how to close it up? Thanks!

Tags: repairing lawn mowers with your own hands Video in the rogue cork comes out air

Small, yes remote. A plug of a gas tank of a Chinese lawn mower, which can bring a serious problem!

Gasoline flows from this elastic band when you gas, what can be done so that it does not flow, you can cover with a sealant? Or there are other options?

Sergey (Rosi) elastic bands are sold like remote controls with hose

Sergey (Rosi) only they come in different types, under a wide way and under a narrow one, and also in the thickness of the tank

Dmitry (Marah) What are they correctly called? To ask the seller.

Konstantin (Hannelle) Fuel hose. Adapter of the fuel hoses of the benzotrimer. Ask so, I think he will understand what we are talking about!

SSD (cielo) I coated with sealant. Holds. Check if the gas tank bars is still working

SSD (Cielo) Sapun is in the gas tank cover

Andrey (deane) sealant in this case, will not hold for a long time.It is better to replace

Yuri (Phaedra) can be planted on sealants, preferably red.If it is well degree and let it hold well well.Good luck!

Dima (Lale) I changed the elastic band this along with the hoses in the kit, it is not expensive, what kind of sealant, replacement and everything

Vasily (Alekanekelo) Why, in principle, gasoline splashes out of the tank?

Why are the leaves of the tomato seedlings twisted

Laying paving slabs on sand video lessons

Do.it.yourself repair of the lawn mower with your own hands is the main malfunctions and their elimination

Details: repairing the lawn mower with your own hands The main malfunctions and their elimination from this master for Olenord.com.

Benzotrimmer. malfunctions and their elimination.

Benzotrimmer. malfunctions and their elimination.

The gasoline trimmer for the grass is extensive distribution due to the low price and ease of operation. It is needed to care for the sites and among the summer residents and the owners of personal houses. Because this tool is used exclusively in the warm season, before operation, the tool must be checked and prepared. grease the rubbing parts, pour the fuel mixture, put the cutting headset.

In the work of at least some kind of technique, malfunctions and malfunctions happen in order to eliminate them without the help of others, you need to understand the device of your unit and the principle of its work. To do this, first, it is necessary to study the annotation of the operation, which the merchant in an ineffective manner applies to equipment when selling.

The iron tubular bar is attached to the gearbox of a two.stroke gasoline engine. Snutsi the bar passes the shaft, which transfers the torque from the gasoline engine to the cutting mechanism. Cutting headset can spin at a speed of 10,000 to 13000 rpm. The most common repairs of the trimmer for grass and the malfunction of the benzos, the reasons for their occurrence and methods of elimination (in the form of questions and answers) are described. The gearbox body should have holes through which lubrication is made. For ease of use of trimmers for grass, equipped with a belt and a shoulder belt. The mowing occurs specifically by the cutting set, which is placed in the trimmer head, it is most and is subjected to wear. To change the fishing line for a trimmer, you need to either wind the latest on the bobbin, or install another coil with an already wound fishing line. A handle on which control levers are placed to the rod. The cutting mechanism is protected by a special casing. Two.stroke lawn mowers are seasoned with a consistency of gasoline and oil, which is poured into a fuel tank. In four.stroke. gasoline is poured into the tank, and the crankcase oil.

The engine does not start. If your benzotrimer does not want to start in any way, first check the presence of fuel and its quality. Low quality of gasoline can lead to the failure of the piston group. Then expensive repairs are guaranteed for you. The main malfunctions of the microwave and ways to eliminate them. It is fundamentally also correctly preparing the fuel mixture. The proportions of gasoline and oil are always indicated in the leadership. The mixture should be fresh, because during storage it loses its characteristics.

The whole premise that the braid for the grass did not start is pollution of the fuel filter. In this case, you need to check the condition of the filter and, if necessary, change it. It is forbidden to operate a tool without a fuel filter. If the engine is junk, it is also worth checking the air filter. When contaminating, the part is removed, washed in gasoline and put in place. If this is not possible, you can rinse in water with a detergent, dry, moisten with oil, squeeze and install in place. If all of the above is already tried, but the engine still does not start, then try to adjust its speed at idle, twisting the carburetor screw.

DIY lawnies repair: analysis of malfunctions and methods for their independent elimination

DIY lawnies repair: analysis of malfunctions and methods for their independent elimination of gas.

Good afternoon, today we will find out what is called automobile clutch, what malfunctions most often.

Fast launch. Put the tool so that the air filter is at the top. With this arrangement of a trimmer for the grass, a fuel mixture is ensured exactly in the bottom of the carburetor. If you remove the air filter before starting and pour a few drops of the fuel mixture directly into the carburetor, then install the filter and the lid in place, then most likely the engine will start on the first attempt. If it did not help, and this, the problem can be in the spark plug. Possible malfunctions of the lawn mower and ways to eliminate them and much more can. Then it needs to be twisted, check its performance and dry the combustion chamber. A non.working candle is easy to replace with a new. But, if the candle is in order, the filters are clean, fuel is fresh, and the braid for the grass still does not start, then you can try to close the air damper, pull the starter once, then open and pull the starter handle several more times. This procedure is repeated from three to five times. With non.careful handling and excessive zeal, you can disable a starter. If the cable broke or the handle broke, then the repair can be made independently, in other cases, it is necessary to replace the starter entirely.

Replacing the spark plug. Replacement must be made when the engine has already cooled down. To do this, disconnect the wire from the candle and unscrew it. The candle needs to be replaced if it is very contaminated or has cracks on the case. Please note that the gap between the electrodes should be 0.6 mm. The new candle is inserted into the engine and tightened with the key, then the high.voltage wire is connected.

The engine stalls after starting. Most likely the carburetor was incorrectly adjusted, or its reservation occurred. The fact that the reason can be understood by vibration during work. You can adjust the carburetor independently by following the operating instructions. A trimmer for grass can also stall when the fuel valve is clogged. Trimmers malfunctions and their elimination | Page 27. Then he just cleanses. If the engine stalls sharply, it is possible to supply fuel to the carburetor. You need to loosen the valves of the carburetor. Or there is excess air in the carburetor, here you need to add engine speed so that the excess air leaves the fuel system faster. It is also necessary to check the integrity of the fuel hose. In case of mechanical damage (cracks, punctures, etc.P.), it must be replaced.

Cleaning and storage. Cylinder ribs and channels in the gasoline case should be clean, otherwise it is fraught with an overheating of the engine. Before cleaning, let the engine cool down. Cleaning the outer surface is carried out with a brush. Plastic parts can be cleaned with kerosene and other solvents or special means. For long.term storage from the fuel tank, the entire mixture is drained, then the engine is launched to develop the remaining fuel in the carburetor. Store the tool only in its pure form.

If you could not repair it with your own hands, it is worth evaluating that it is more advisable, contact the service or purchase a new trimmer for grass.

Modern technologies and technology allow you to produce the best and optimal technical solutions that become effective assistants when arranging a summer cottage or personal plot. Green lawn and other stands can grow rapidly, to put the house mowl is used to put in order and haircuts of lawns, which is differently called a motorcycle or a trimmer, a benzo-core.

Traditional braids for grass are inconvenient and unsafe in use, require significant expenditures and their own forces that will help to save law mowers that combine functionality and practicality in their design. In the photo Benzosos, you can see various high.tech devices that have a complex of operational characteristics, including parameters such as increased performance and long service life.

A convenient and reliable trimmer for grass is a technical device consisting of individual mechanisms, details and elements that can be worn out, become unusable and damaged during intensive operation.

How To a Fix a Chainsaw that keeps flooding and dying at idle and bogs on throttle acceleration

Even when conducting a regular technical inspection, care and care procedures, such devices and their individual parts require repair and even replacements, all repair procedures can be carried out independently.

The easiest way to give the lawn mower for repairs, allocating a certain amount of funds from the family budget, operational and high.quality repair with your own hands is no less simple and convenient to understand the design of the lawn mower and fix all the problems.

The massive and piece manufacture of trimmers is based on the use of generally accepted technology, the typical design scheme consists of certain elements and parts, it is important to know them when carrying out independent repair work:

When you press gas

If the gas pump stops when you press the gas, the reasons may be the following.

  • The most common option is to adjust the carburetor. which occurs with significant loads on the drive, after prolonged inactivity of the mechanism or when using it in severe conditions.
  • The fuel valve is clogged, which eliminates its relaxation, as a result of which gasoline in the system begins to flow normally.
  • Weakening and lowering the cable in the carburetor. The expansion of the fuel hose can also occur before it breaks, caused by the action of a significant load.
  • A clogged chimney (check valve), which leads to a lack of fuel in the tank.

If the problem is related to the carburetor block, then this can be recognized as the appearance

When the hose is torn or the cable is stretched, the replacement of these components is performed.

the trimer will not be stained, and if it starts, it immediately stalls

Forum / smoking room / trimer will not be stained, and if it starts, it immediately stalls

Ask your question at our forum without registration

And you will quickly receive an answer and advice from our specialists and visitors to the forum! Why are we so sure of this? Because we pay them for this!

Why is a trimmer for grass stops when you press the throttle, with high and lack of speed, when heated or opened by the air damper

A gasoline.drive grass braid is a useful thing for owners of home plots, lawns, and when a trimmer for the grass suddenly stops, work on cleaning the territory from the grass stops. The device itself is a rather complex mechanism, so there are many reasons for its breakdown. The most common faults are operating instructions. Know the reasons why the trimmer stops for the grass, it is necessary to repair the device yourself.