Gasproof gas station proportions. Fuel mixture proportions

Friendship chainsaw how to breed gasoline

Found in the garage the domestic chainsaw of the Urals. The spouse dismantled, cleaned, says how new should work. What kind of oil is poured into the Urals to try to turn on. What gasoline such a chainsaw will be optimal for?

The Ural chainsaw is considered a descendant of a firmica chainsaw. a reliable and worthy unit. If you adjust it well and regularly use, then such a saw almost always shows a stable job.

As for gasoline, earlier the AI-76 brand was poured into such a chainsaw, now you can pour A-80. As for the oil, you can use the domestic M8-B or any other imported oil for a two-stroke engine. Oil should be added to gasoline in a proportion of 1:25.

First of all, read the instructions for the operation of the chainsaw of the domestic.

What kind of oil and in what proportions, this topic is given to the whole head of the instruction.

You write about the Ural chainsaw will be the best option “Autol” (this is M-8V motor oil).

If you mean the oil for the preparation of fuel mixture for the chainsaw, then the proportions of 1: 20 (oil to gasoline).

The same oil can be poured into a chainsaw gearbox.

Since the Ural chainsaw is a descendant of the Soviet chainsaw “Friendship”, and “Autol” (M8-B oil) was popular with the Union (recommended for use in gas, ZIL and and and and and and.t.D inclining “Ural”), it is considered the best option for such a chainsaw plus to everything, the price is completely affordable.

When buying oil, pay attention to the marking, there should be a GOST.

M-12TPU oil, MGD-14M and.t.d, these are all domestic oils, you can use imported ones, but domestic ones are better.

For 1 liter of gasoline, add 30 g of special engine oil. Pour gasoline for chainsaw? (Ural, friendship, etc. How to dilute gasoline for a chainsaw? The acquired mixture is poured into a special compartment for fuel.

To dilute gasoline for a chainsaw. It is necessary to consult a specialists before this. It is best to ask those who work in the service center for their repair.

And the sellers who advertise them in the supermarket and hang all kinds of noodles on our ears, they will not tell us anything traveler.

I had it like that, but not with a saw, but with a scythe. How to dilute gasoline with. restart24.ru. She worked poorly, did not start very well, detonated hard and did everything to mix gasoline and oil, as sellers said.

But when he turned to the service center, they said a completely different ratio of fuel parts.

For a saw, you need to take gasoline AI-95 or AI-92 and mix in a ratio with oil-in 1l gasoline 40g of oil

The ratio of gasoline and oil for chainsaws

The proportions of the oil and gasoline for refueling two.stroke engines of the chainsaws of different brands are 40 to 1 or 50 to 1. This ratio is standard, which is used not only by newcomers, but also by experienced sawmills. It is such a ratio for the preparation of the fuel mixture that is close to the ideal, and provides a lubrication of the rubbing parts of a crank mechanism and a piston.

It is interesting! Before mixing oil products, external factors should be taken into account. If the chainsaw is new, then it requires the passage of the running.in, and for this you need to add 20% more to combustible oil than standard values. 20% more lubricant is also required to add if the work is carried out at low temperatures.

How much oil should you pour in gasoline in milliliters? In the calculation per ml of the proportion of oil and gasoline 1 to 50 is 20 ml per 1 liter. To prepare the correct mixture, you should type 1 liter of gasoline in a plastic bottle, and dilute it from 20 ml of oil. To correctly measure how much oil is pouring, you should take a special measured container, and fill it to the corresponding mark. If you immediately plan to prepare 2 liters of fuel, then this amount of gasoline must be added 40 ml of lubricating material.

The BEST Fuel For Your 2 Stroke Equipment!

There are other relationships that different manufacturers offer. These values ​​of the ratio differ slightly, but if you read other values ​​in the passport to the tool, then it is necessary to adhere to them and adhere. Value 1 to 50 or 40 are standardized. Pour 15 ml of oil per 1 liter of fuel in the summer, and in winter to add at least 20-25 ml. Knowing the recipe for the preparation of the mixture, you should understand the question of which gasoline to fill in the chainsaw?

Gasoline and oil for chainsaws. which is better

Often, beginners ask, which is better to take gasoline for their tools? In order not to make a mistake in choosing, it is recommended to familiarize yourself with the instructions for the tool. In the instructions, each manufacturer indicates the corresponding brand of fuel. If the manufacturer indicates that the octane number should not be lower than 95, it means to pour 92 gasoline is not recommended.

Now we’ll figure out which oil is better to take for the matts of chainsaws. For such purposes, special oils are used. Taking motor oils of cars for the preparation of the fuel mixture is prohibited. For chainsaws, you need to buy lubricants for two.stroke engines, which are on sale not only in specialized centers, but also in online stores.

It’s important to know! It is necessary to distinguish that manufacturers produce two types of lubricants for chainsaws. for circuits and engines. Chain materials are poured into a separate tank of the tool, and they are spent on the lubrication of the chain during the operation of the chainsaw.

Motor oils for two.stroke engines are produced by such manufacturers:

Typically, the ratio is indicated on a bottle with lubricant, so getting confused with the preparation of the fuel mixture will be difficult even for beginners. Under any pretext, do not use working out even as a lubricant chain material. This will lead to the fact that soon you will need to carry out the repair of the tool.

Preparation for operation and running.in

The goods are delivered in the collected form, it is only necessary to install the tire, put on the chain, adjust its tension and securely fix all the nodes and details.

Important: adjust the chain so that it moves freely along the tire without stopping and without causing extraneous noise.

  • To run the chainsaws, use the fuel mixture in a ratio of 1/25. The preparation of the mixture is carried out on the basis of gasoline AI 92-95 and high-quality oil for two-stroke engines. The manufacturer recommends mineral or semi.synthetic oil champion.
  • Before the sawing of the saw, put it on the ground, press it with one hand, and smoothly pull the starter’s handle until a tangible resistance. After that, sharply pull the launch cable handle.
  • Develop one fuel tank at idle, prepare the fuel mixture, observing 1/50 proportions.

Important: do not forget to refuel the automatic lubrication system of the gearbox and circuit. Use only high.quality oils, do not use spent liquids.

To run into the new saw Champion 251-18, it is necessary to develop 8-10 fuel tanks. Do not overload the chainsaw at this time, do not allow engine overheating.

All work with the saw should be carried out in accordance with the instructions of the manufacturer and with strict compliance with the safety rules.

The advantages and disadvantages of the model

  • requires high.quality combustible materials;
  • Needs properly running;
  • There are problems with the plant at low temperatures.
  • no fuel;
  • malfunctions in the ignition system;
  • The fuel supply system or air filter was clogged;
  • the carburetor is not tuned or contaminated.

Oil and gasoline proportions

The exact ratio of oil and fuel is indicated in the instructions for the chainsaw or on its packaging. Equally bad both do not add and pour oils. If you use the material and saw of the same company, you will need to add 50 parts of gasoline to one part of the oil. If the brands are different, it is better to reduce the amount of gasoline to 40 parts.

Follow not advice from the Internet, namely the information specified in the instructions for the chainsaw. Different manufacturers recommend different proportions of materials, the ratio can be 1:30 or even 1: 100.

It is critical to observe the exact ratio of gasoline and oil. To measure the correct volume, you can focus on the dispenser on the packaging with butter or use a medical syringe. You can also find special mixing containers on sale, which will help to measure the volume of both means.

It is better to prepare the mixture in a volume necessary at once. According to the recommendations of technologists, in a mixed form, the mixture cannot be stored for more than three days. With prolonged storage in the mixture, tarry deposits are formed, combustible properties deteriorate.

AI-92 fuel is most suitable for this mixture. Different additives are often added to AI-95, you can find many fakes.

Dilute fuel and oil must be in dishes made of metal or dense plastic, which does not react with oil products. Food plastic cannot be used, since under the influence of gasoline it will decompose and change the properties of the fuel mixture.

Oil quality criteria for:

proportions, fuel, mixture
  • A good degree of adhesion. You need to drop a couple of drops of oil on your fingers, squeeze them tightly and push them out. Adhesive oil will be pulled between the fingers. The remaining types of oil will simply lubricate the skin.
  • Density. The more liquid oil, the greater he has consumption. From our own experience we can say that the STIHL oil is more economically consumed and, accordingly, it is more economical. Thick oil is more slowly consumed, but it penetrates worse into hard.to.reach areas of the chain and freeze very quickly in the cold. liquid oils penetrate the nodes better, but fly faster due to centrifugal force.
  • Environmental friendliness. To minimize the damage to the environment, it is advisable to choose a plant.based oil that can decompose after use.

How to dilute the components of the mixture

As mentioned above, gasoline with butter should be diluted in a specially prepared capacity. Do not do it in a gas tank. The last technology will lead to the fact that part of the oil will enter the carburetor. As a result, you will have to disassemble the engine and wash it.

Standard dilution proportions 50: 1 and 40: 1. Such a mixture will not prevent the combustion of gasoline in the gas tank and improve the grease of the rubbing parts of the mechanism. When running a new tool, it is advisable to add lubricants twenty percent more. It is recommended to dilute with a large amount of oil in areas with a high air temperature.

Many owners will be interested in information on how to dilute gasoline with butter if there is no measuring capacity. For this, twenty cubic medical syringe is suitable. Although most often measuring containers are included in the set to chainsaws.

Before diluting fuel, it is necessary to clean and degrease the neck of the gas tank. Pour it through the filter. Any rag will serve as a filter

After use, it is necessary to drain the remaining mixture and dispose of. Remember that it is better to shift than underdraw. What will happen if you do not take into account the recommendations, read below.

If you act not according to the instructions, then you can bring the tool to a non.working state. For example, if you do not dilute the fuel, then the cargo will form more often, the necessary lubrication of the piston will not occur, as a result of which the temperature in the engine will rise. And this will lead to the fact that the pistons will break. Or the owner of the saw will inhale toxic pairs in large numbers throughout the work. Thus, he will earn health problems, break the tool.

If you use lubricant and fuel low.quality, then they can also lead to engine breakdown. It is not recommended to dilute the engine oil made for cars. Fuel needs to be bought with a high octane number.

Overview of oil manufacturers for internal combustion engines

STIHL’s lubricant Stihl is one of these oils that are used directly for chainsaws. They enter the shops in bottles and cans of 5 liters. This type refers to mineral. They have a cheap cost of sale. However, less high.quality than synthetic.

Synthetic materials retain their lubricants for a long time. With an increase in temperature, they can not fade after the first heating. Do not distinguish toxic substances that can damage the health of the owner.

Husqvarna lubricant is used to lubricate the chainsaw engines of the same company. It must be diluted in gasoline in a proportion of 1:50. Or 20 grams per liter of fuel. Lubrication of engines from manufacturers of another company must be diluted in a proportion of 1 to 33. That is, 30 grams per liter of gasoline. This component for diluting fuel consists of mineral elements by seventy percent. Synthetic impurities are also added. But their share is a small part. 30 percent. This lubricant is intended for the CIS countries, where there are problems with high.quality gasoline.

“Kreissman”, an example of which was given, is used for two.stroke chainsaw engines. Dilute oil with fuel should be in the same proportions that were indicated above. “Kreissman” does not allow the fifter to form, perfectly lubricates the pistons and other engine details.

Tool manufacturers usually equip a chainsaw with their own lubrication material. This is how the best ratio of lubricants is achieved and the service life of the saw increases.

proportions, fuel, mixture

The ratio of gasoline and oil for chainsaws

The proportions of oil and gasoline for refueling two.stroke engines of chainsaws of different brands are 40 k to 1. This ratio is standard, which is used not only by newcomers, but also by experienced sawmills. It is such a ratio for the preparation of the fuel mixture that is close to the ideal, and provides a lubrication of the rubbing parts of a crank mechanism and a piston.

Fuel mixture preparation proportions

It is interesting! Before mixing oil products, external factors should be taken into account. If the chainsaw is new, then it requires the passage of the running.in, and for this you need to add 20% more to combustible oil than standard values. 20% more lubricant is also required to add if the work is carried out at low temperatures.

How much oil should you pour in gasoline in milliliters? In the calculation per ml of the proportion of oil and gasoline 1 to 50 is 20 ml per 1 liter. To prepare the correct mixture, you should type 1 liter of gasoline in a plastic bottle, and dilute it from 20 ml of oil. To correctly measure how much oil is pouring, you should take a special measured container, and fill it to the corresponding mark. If you immediately plan to prepare 2 liters of fuel, then this amount of gasoline must be added 40 ml of lubricating material.

There are other relationships that different manufacturers offer. These values ​​of the ratio differ slightly, but if you read other values ​​in the passport to the tool, then it is necessary to adhere to them and adhere. Value 1 to are standardized. Pour 15 ml of oil per 1 liter of fuel in the summer, and in winter to add at least 20-25 ml. Knowing the recipe for the preparation of the mixture, you should understand the question of which gasoline to fill in the chainsaw?

What gasoline to fill?

The quality of combustible material affects the traction of the engine, the speed and coherence of the operation of all elements of the system. In different models of saw, fuel is poured with different octane numbers. Local tool manufacturers advise taking the AI-80 low brand fuel. Sometimes they make a mixture from AI-80 with AI-92. For foreign models, the octane number should not be less than 90, so AI-92 and AI-95 gasoline are recommended. In all cases, it is necessary to use unhealthy fuel so that it does not contain lead, which adversely affects the details of the tool. How to dilute gasoline with a chainsaw oil? We must be guided by the recommendations of the manufacturer. Otherwise, it is quite easy to damage the tool and break all the factory settings.

How to season the chainsaw of a gas-oil mixture properly

The freshly prepared mixture must be stored in a dark room, but not more than 2 weeks. It is best to mix immediately before using the tool. The refueling procedure is implemented by performing the following manipulations:

  • Before unscrewing the tank cover, it is necessary to clean the surface, and even better, blow the hose from the compressor.
  • Put the chainsaw on the side so that the lid is on top. At the same time, consider one important point that refueling should not be in the wind in order to prevent dust and other contaminants in the tank.
  • Put a watering can on the neck, which will eliminate the probability of pouring fuel.
  • Fill the tank, but do it so that there is a place left. This is done in order to exclude the likelihood of gasoline flow during screwing the lid.
  • After refueling the chainsaw, be sure to pour oil into the tank for lubrication of the chain.

We launch the motor, and are convinced of its good functioning. Smoke from a chainsaw should come out of a light color, and in a volumetric amount only with an increase in speed.

Selecting two.stroke oil for a chainsaw

Having decided on the question of how to breed gasoline with butter into a chainsaw, it is worth finding out which type of lubricant is better to use. First you need to understand that mixing fuel is required exclusively with two.stroke oils, but not motorized for automobile engines, and even more so, working out.

Special oils are called. two.stroke. By color, they are not only red, but green and blue. Red color indicates that it is mineral (cheapest). Blue and green. semi.synthetics. Semi.synthetics are naturally better, but when it comes to one.time use (t.e., When the lubricant burns with gasoline, then mineral oil is the best option in terms of cost and reliability). The color of the oil also indicates the use of the appropriate additives, but the most important thing is to choose a lubricant, well.known manufacturers need. By color, you can determine that fuel is mixed with grease.

Today it is very easy to buy a fake or lubrication of low quality, so you should not save. The following manufacturers are recommended to choose two.stroke oils:

If when buying expensive oils, they tell you that you are overpaying for the brand, then this is so. Only you pay for the guarantee that the purchased substance is high.quality, and has only a positive effect on the engine engine. No need to look for options cheaper, because saving on fuel and lubricants, you reduce the life of the engine and the entire tool in general.

Interesting to know! Two.stroke oil has a different consistency and the number of additives. Motor oil is intended for constant lubrication of mechanisms, and two.stroke lubricates the parts when contacting it, and when it enters with gasoline into the cylinder, burns out.

Summing up, it should be noted that the chainsaws are necessary to refuel a gas-oil mixture in a ratio of 1 liter of fuel add 20 ml of oil. If you use a proportion using 25 ml of lubricants, then nothing terrible with the ICE will happen.

What gasoline to use for chainsaws? How to breed it correctly?

Chainsaws are simple in the device and is necessary in private households. The device cannot work fully if you do not use the correct fuel mixture that you should be able to prepare.

Each chainsaw has various technical data and can perform different work.

Powerful saws are suitable in order to bring down centuries.old trees, small chainsaws are more suitable for various work in a personal economy:

The design of the chainsaw is simple, there is not even a gearbox, a two.stroke power plant operates, it contains one gasoline cylinder.

Standard chainsaw blocks:

  • Power point.
  • Clutch clutch.
  • Ignition unit.
  • Carburetor.
  • Fuel block (tank for oil and fuel).
  • Filters for cleaning the incoming air.
  • Starter.
  • Chain.
  • Tire.
  • The brake of the chain.
  • The mechanism of tension.
  • A chain lubrication.

Each chainsaw requires high-quality fuel and lubricants, it is they that provide prolonged productive functioning of the unit. What gasoline for a chainsaw is poured, in what proportions?

For domestic chainsaws, simple oils are suitable, foreign chainsaws need more complex fuel mixtures, which have passed careful cleaning.

Owners of chainsaws are primarily interested in fuel consumption. The volume of fuel container is usually 550 ml. Suppose the power of the device is only two kilowatts. In one hour of work, such an unit will consume 1.25 liters. If the tool is functioning in the forcing mode, then the fuel may be enough for 20-30 minutes of continuous functioning.

The choice of fuel

What kind of fuel to choose for a chainsaw is an osky question, the success of the unit directly depends on it. According to existing canons, good gasoline for a chainsaw is considered not ethylated, but highly octane from a proven manufacturer. The cleaner the fuel, the better. If gasoline was stored in the canister of a year and a half, then this will adversely affect the nature of the device, so the substance should be prepared before the start of work.

It is recommended not to use low.octane fuel, to completely eliminate inexpensive oils from the circle of attention of dubious quality. Do not use ethyl fuel, it significantly reduces the resource of the power plant.

It is important to track so that there is no alcohol in fuel, any additives that may violate the functioning of the power plant. Specialists still conduct discussions that it is better than 95 or 92. The first has more stable detonation, but most often they still use the 92nd. The reason is simple: questions often arise to the 95th, it has a large number of different additives that have a poor effect on the work of the saw engine. Michentonization occurs (piston pulse into the opposite move), which takes place almost with each turnover of the crankshaft. If the octane number is even higher (98), then microuders will become even more intense.

The consequences of improper gasoline on the quality of the unit can only be negative:

Step.by.step instructions for refueling

Wanting to season the chainsaw, you need to follow the simple algorithm:

  • Prepare fuel in the recommended proportion of gasoline and oil for two.stroke chainsaws.
  • Prepare the saw for refueling, cleaning its surface from sawdust and chips.
  • Put the saw on a flat stable stand with a tank with a tank up.
  • Gently place a small funnel (plastic or metal, resistant to combustible materials, easily purchased in the auto.goods store in the auto.goods store)
  • Carefully pour fuel into the tank, avoiding overflow. It is unacceptable to pour under the lid. this will lead to splashing out during screwing the cover!
  • Close fuel tank lid
  • Replace the lubricant for the chain (mandatory!)
  • Start the motor at idle.

After prolonged downtime, you need to drain the rest of the fuel mixture from the saw. You can’t use it. since gasoline quickly loses its properties in such a mixture. The consequence will be unstable work and risk of breakdown.

What will happen if you fill in the surgery in the chainsaw

When the owner of the chainsaw for some time will use it, he may want to conduct some modification of the tool. And it’s good if his desires are limited to the purchase of various nozzles that expand the functionality of the chainsaw. But some go further. they begin to experiment with gasoline and butter on which their saw works.

If we have already talked about gasoline earlier (most modern saws require it with a high octane number-not lower than 92-95), then it is worth saying about the oil. Many motorists have a significant amount of machine oil used during the operation of the car. And therefore, some have a desire to use this material to refuel a chainsaw.

40:1 Fuel to oil ratio easy way to calculate

If this is done, then the engine will fail. The reason for this will be, first of all, the low lubricant of the re.used oil. It will burn with a large release of black soot. The metal particles contained in the oil will first score the fuel filter (these are those particles that are larger), and then. the sealing rings of the cylinder will fail. The metal suspension in the oil will damage the surface of the cylinders themselves and bearings.

Some “rationalizers” try to use working out to lubricate the chain itself and the pads on which it is located. This will not lead to anything good. What exactly will happen. you can see in the attached video.