How the snow blower works on a single axle tractor

How a snowplow works on a single axle tractor

Since you can make three types of snow shoveling attachments yourself, it is worth considering all the options. As a result, it remains to choose the most suitable for each case.

Bulldozer type

The blade is mounted on the main unit by means of brackets and rods. Pull rods should be mounted in the eyelets of the blade and lead to the control levers with rollers or metal tubes. This simple device will make a snowblower out of your power tiller.

Rotary snow blower

This type of snow removal equipment consists of several elements:

You will need four rings made of sheet metal to make the auger. They must be cut on one side and the ends opened to the size of the diameter. After that, one end of the ring is attached to the blade of the gripper by welding, and the second end should be strengthened with a metal strip. A hole of any shape is cut out behind the gripper, into which a pipe of appropriate diameter is inserted.

It should be remembered that the distance between the blades and the back wall of the box must be as small as possible. The shaft should be mounted on bearings so that one end of it would protrude from the box by 50-100 mm. This is where the chain drive sprocket will be attached. Manufactured in this way, the snow blower attachment on a single axle tractor will perfectly cope with the task at hand and greatly facilitate the life of the owner of a country house during the winter period.

Fan unit

This snow blower equipment contains the following elements:

In the upper part of the drum should be cut a hole for the exit of the snow, and then press into it the impeller. At the same time, it should be located so that the blades were parallel to the axis of rotation. The blades should be sharpened beforehand, and then welded to the drum.

Auger-fan nozzle

The last type of snow blower is the most difficult to make. The composition of the unit is as follows:

The auger shaft is made of a pipe and two pins. 8 steel half-discs with a thickness of 2 mm are welded on the pipe. They should be fastened so that the result is two intersecting spirals.

Make a snow blower with your own hands from a motor cultivator is not as difficult as it may seem. The use of improvised materials will save a considerable amount of money, because similar ready-made equipment is not cheap.

Making a homemade snow blower

For clearing snow, you can not use the single-axle tractor itself, but only its engine. Roofing iron goes to the manufacture of the auger snow blower body. Plywood 10mm thick is good for sides. The frame is welded from a metal angle. A half-inch pipe is adapted to the handle, and a three-quarter-inch pipe is used to make an auger shaft. A through kerf, made in the middle of the tube, is used to fix a metal plate (blade) that has dimensions of 120 by 270 mm. The shovel is designed to shovel snow as the shaft rotates. Podvodvigat snow mass to the blade in this makeshift design snegobraborschika has a two-entry auger, for the manufacture of which we take the sidewall tires or conveyor belt thickness of 10 mm. One and a half meters of such tape is enough to cut out four rings with an electric jigsaw. Diameter of each of them should be 28 cm.

To make a homemade snow thrower you will need roofing iron, plywood, conveyor belt, pipes of different diameters, metal corners, closed bearings

For fastening the platform of the quick-release motor borrowed from the power tiller, metal corners are welded to the pipe perpendicular to the plate. To freely enter the shaft in the self-centering closed bearings 205 need to make a pair of cuts at the ends and knock them down. After this operation the diameter of the shaft is reduced. A notch is made on one side of the shaft for the sprocket key.

The auger is driven by a chain or belt, if the engine from the motor-block has a pulley. All necessary parts (pulleys, belts, bearings) can be bought in auto stores

Better to put the machine on skis instead of wheels, which would get stuck in the snow. Skis base is made of wooden bars, on which the plastic pads are fixed for better sliding. Boxes used for electric wiring can be used as overlays.

Snowplow on skis glides through the snow easier, so the person driving it, they have to exert less physical effort

Turning chute, needed to throw the snow in the right direction, made of a plastic sewer pipe of large diameter (at least 160 mm). Fix it on the same tube of a smaller diameter, attached to the body of the auger. A piece of sewage pipe is attached to the turning chute, which will direct the ejection of snow. The diameter of the chute must be larger than the width of the auger blade, so as not to delay the progression of the snow mass.

View of a homemade snowplow equipped with a motor from a power tiller, assembled before testing its performance in a snow-covered yard of a private house

To give the homemade construction a presentable look, it is necessary to paint all of its parts in bright color. After completing the work samodelka tested, and then operated throughout the winter period. Some masters go even further, making a self-propelled version of the snowplow.

Mechanize manual labor aspire to all people living on earth. After reading how to make a snowplow from the motor block engine and other spare parts, some will not “reinvent the wheel”, and decide to buy the factory model snowplow. To buy a budget version will require about 20-30 thousand. rubles. It is 1.5 to 2 times cheaper to buy a factory-made auger for your power tiller. To assemble a self-made design will only have to spend money on the purchase of some spare parts, as well as to allocate a couple of days to perform the work. In any case, the problem of removing snow from the lawn will be solved.

Making a snowplow for a motorblock with their own hands drawings, video and photo | single axle tractor and cultivator with their own hands

In recent years, winter pleases us with a large abundance of snow. If for fans of sledding and skiing it is a special joy, the owners of cottages and private houses are reminded of snow removal. One option to simplify and speed up the monotonous work. the purchase of a personal snowblower.

Not everyone can afford to spend a few tens of thousands to purchase branded snow thrower, which will be in demand 5-7 times during the winter. You can make a snowplow for your own hands. The engine of a power tiller is used for this purpose.

It can be purchased separately or removed from machinery not in use in the winter. If an air-cooled electric motor will be used in the snow blower design, it is necessary to provide for the installation of a snow guard for the air intake.

Because there will be a lot of snow in the air when working.

How to make a snowplow for a power tiller with his own hands drawings

To make it easier to cope with the snow blower, the width of the grab at this design. 50 cm. Proper size for sweeping garden paths in winter. In order to snowthrower could start in a garage or shed through the door, the overall width should be 60-65 cm.

For the manufacture of the auger body of the snowthrower, we used roofing iron. The sides are made of plywood (10 mm). In the manufacture of frames used metal angles (50×50).

The handle was made from a half-inch pipe. Auger shaft is made of pipe (3/4″). In the tube, in the middle, a through cut is made for mounting a metal plate (120×270 mm).

As the shaft rotates, this plate will begin to shovel snow.

The snow will be moved to the plate thanks to the two-way auger made from the conveyor belt. Also four rubber rings are attached to the special plates.

The bearings are put on the tube. If the inside diameter of the bearing is smaller than the outside diameter of the tube, the tube must be ground a little. You can see from the drawing that adapters have been used for the bearings.

To make the auger you need 1.5 m of conveyor belt. A thickness of 10 mm is desirable. You have to cut 4 rings out of it, which should be 28 cm in diameter. You can use two screws screwed into the plank and rotate the belt in a circle. Or use an electric jigsaw.

Self-aligning sealed bearings 205 must be used to rotate the auger. The bearings should be closed to avoid snow.

If the design includes an engine from a power tiller with a pulley installed, then the auger will be driven by a belt or chain. The pulleys, belts and bearings you need for this are available in auto shops. The auger will idle at up to 800 rpm.

A safety pin is provided to prevent ice from getting into the auger. When the auger jams, it will shear off. If a belt drive is used, a pin will be an extra safety feature, allowing the belt to slip.

Auger width is 2 cm less than body size. This is to keep the clearance between the auger and the housing small and to prevent the auger from snagging the housing. The snow blower design provides for the possibility of relocating the engine in just a couple of minutes to another vehicle.

To do this, the engine mount is made quick-release, which allows you to not use a tool when repositioning. The process of clearing snow from the snowblower will be much easier if you remove the engine. Because the weight of the snowblower is primarily the weight of the engine.

Description and construction of the snow blower for power tillers

The base of the skis is made of wooden bars, to which the plastic pads are attached. In this case, boxes from the electrical wiring are used.

A piece of plastic pipe, 160 mm in diameter, is used as the main part of the turning chute, which throws the snow. Chute, which throws snow, is attached to the pipe. The width of the auger blade should be less than the diameter of the gutter, so it will be carried out ejection of snow.

For the manufacture of frames we use metal angles 50×50 mm. Cross bars 25×25 mm are welded to them. A quick-detachable motor platform is installed on them. Cross brackets and a handle are attached to the frame longitudinal brackets with M8 bolts.

In this case, we used this principle of snow thrower. It doesn’t need wheels, only for moving around the barn.

Therefore, instead of wheels, there are skis that allow the snow to be removed from the tracks when the snow blower is tilted forward. If tilted backwards, the snow can be shoveled in stages, in case of a small snow cover.

Can be retrofitted in the future as a self-propelled snow thrower with a wide track without major modifications.

After painting, the made snow thrower will look like a brand-name snow thrower.

Blueprints of a homemade snow thrower for a power tiller

The principle of operation of the homemade snow thrower is as follows:

Tips for using the snowblower

Depending on the level of precipitation, a single-axle tractor, together with a snowplow attachment, is put on:

Pneumatic Wheels Grouser Track Attachment Lynx

In case of heavy snow at all, it is recommended to install a crawler attachment on a single-axle tractor, turning this agricultural device into a real snowmobile. Such an attachment will not only allow for better snowmaking, but will also allow the single-axle tractor to be used as an all-terrain vehicle.

Caterpillar snowmobile attachments are sold in specialized stores or made on your own, using recommendations and drawings from the craftsmen on the forums.

To create a snowmobile, you may need skis or sleds, or a special trough.

We suggest watching a video, which shows different variants of self-propelled units on track, made from a power tiller:

You may also be interested in diagrams and drawings of a self-propelled snowmobile from a power tiller:

• frame front crosspiece (1);
• a stand made of steel pipe (2);
• A handlebar support made from 25×25 angle (3);
• steering shaft made of steel pipe (4);
• a crossbar made of 28×28 steel pipe (5);
• bipod (6); bronze washer (7)
• Support sleeve with an angle (8);
• nut, type M10 (9).

Popular models of snow blowers

Among the huge range of products offered by manufacturers, the following equipment is the most sought after:

Megaladon-0,6 rotary equipment for “Salyut” snow removal power tiller

Rotary snow plow attachment to the Salyut model Megaladon power tiller is used as an attachment for clearing small areas. Mounted on a single-axle tractor at the front with a special mounting device included.

• The main working element is an auger with teeth.
• The shaft rotates and conveys the snow mass to the center and then enters the snow vortex.
• The operator selects the direction of snow discharge by rotating the screen of the device.
• The amount of distance over which the snow will be thrown depends directly on the motor power, as well as the angle of the snow outlet device.
• The height of snow is adjusted by special snow thrower skids at the bottom of the machine.
• The snow blower is attached to the front of the power tiller, which eliminates the need to turn the wheel and work in reverse gear.
• Ability to continue working after stopping the snow blower by transferring torque from the engine.
• Auger is made of high quality material by a state-of-the-art laser machining facility.
• Meets all required safety regulations.
• The snow blower chain is in a special protective cover and is separated from the immediate work area.
• Precision snow throw design ensures all selectable settings.
• Lightweight design of the snow plow.

Texas Snow Blade 92000160100 for Texas single axle tractor

Specialized snow plow mounted on Texas single axle tractor (same as Husqvarna single axle tractor) from the front. The burr is replaced by a wheel. Used for clearing loose snow on narrow paths and small yard areas. Included with the dozer blade is a mount.

The snow cover width is 75 cm. The producing country of the attachment is Denmark. Midmarket

For spraying all kinds of fertilizers, different fertilizers and all kinds of chemicals to protect plants from harmful insects not bad to have a special device. The Juke sprayer is a friend to gardens.

All agricultural workers just need special equipment, such as a potato planter, for planting different crops, like potatoes. Here you can learn how to make a potato planter for your power tiller with your own hands.

Till now MAZ-5551 dump truck is one of the most popular eight-ton trucks in Russia. By following this link you will get acquainted with this beautiful machine.

Attachments for Tehas power tillers are selected individually for a particular model, because each auxiliary device is made for a particular machine, taking into account its design features and capabilities.

Sm-0,6 snow thrower on Kaskad single axle tractor

Snowplow head on a single-axle tractor Cascade model CM 0,6 captures and throws the snow with rotating augers, driven by the engine of scooter.

Snow blower on single axle tractor “Mole

Technical parameters of the snow blower for the tiller Krot:

Сп-56 attachment. snowplow on a single-axis tractor “Tselina”

The principle of operation of the Pp-56 on a single-axle tractor “Tselina” is to break ice and compacted wet snow with snow augers and transfer the resulting snow mass to the impeller throwing.

The snow is thrown through the chute guard at a distance of 12 m, and the direction is adjusted with a special lever at an angle of 190 degrees.

Beginning of assembly

To build your own snow blower, you first need to choose the type of device. It is quite possible to get by with a one-stage model if the area is small. For larger sizes, it is better to use a two-stage model.

You should also be guided by the weather conditions. If snowfalls are heavy and abundant, then you just can’t do without an auger snow blower. When the snowfall in the winter is very small, you can make the most primitive machine.

Motor Selection

Electric drives are usually used when the machine will be operating close to a power outlet. You can use the engine from a chainsaw or grass trimmer. Snowplow from a grass trimmer with their own hands often make home masters.

Electric-powered snow blowers are more economical as well as easy to operate. But it should be noted that in maneuverability they are inferior to the gasoline unit. The gasoline engine is considered more versatile, but the price for refueling and maintenance will be much higher than the previous option.

That is why the choice will depend on the specific conditions, as well as the tasks that need to be carried out with the device. It is important to know when choosing an electric snowthrower that the wire at sub-zero temperatures will become very brittle and lose its elasticity, so you need to pick up a good cord, which will withstand low temperatures.

Engine or single axle tractor

When a single-axle tractor is used as the basis for an electric snow blower, you don’t have to worry about choosing an engine. This role is handled by the unit itself. If a gasoline engine is installed in the machine, then you need to use models with internal combustion. They can be removed from the lawnmower.

The entire structure will need to be secured to a quick-assembly platform to facilitate maintenance and repair, should the need arise. It is also desirable to make a manual start motor to reduce weight and increase maneuverability.

The snow blower can also be built on an electric motor. In this case, you should know that this option will limit the radius of the machine. Such a drive is afraid of moisture, and therefore you will have to install a quality waterproofing, so that the engine will not be damaged.

Rotary snow blower for a motor-block with their own hands: drawings and photo examples

Having available a working single-axle tractor and drawings, a rotary snowplow for a motorblock with their own hands. the task is quite feasible. Using the assembly diagrams, you can make the missing elements of the device and use the device for its intended purpose. When selecting a drawing for the work, pay attention to the specified parameters of the product. Taking in your hands the drawing, you will see that it necessarily depicts all the necessary parts with an indication of their dimensions in millimeters. To work you will need sheet steel, a welding machine, and access to a lathe (or the ability to ask a master).

The main part of any snowplow. an auger. For its manufacture, we use a tube and half-discs, made of sheet steel with a thickness of 2 mm. Disks are welded to the pipe, forming a double-sided spiral in the right and left parts. In order for the construction to be strong, special attention must be paid to the welding points.

Useful tip! If available, an old auger that may have been left over from farm machinery can be used.

Auger for rotary snow blower made by hand

The next step is to make the auger movable. Ball bearings 203 are used for this. Using bolts and nuts, their bodies should be attached to the sides of the snowblower. That way the auger will rotate and feed the snow, which trims, to the rotor.

As the basis for the rotor is quite suitable pot of aluminum, with a volume of 20 liters. Using four-millimeter rivets, it is attached to the front wall of the housing. So, falling into the drum, the snow will be thrown by the blades at a distance of several meters (usually 3 to 5 m).

You should also pay attention to the organization of the torque, which is transmitted to the snowthrower from the power harvester. It is transmitted directly from the engine of the snowblower to its shaft, which is already connected to the shaft of the snowblower. The A-100 belt and the appropriate pulley are perfect for this purpose.

Diagram of the drive shaft. 1. drive sprocket; 2,4. bearing housings friction; 3. shaft; 5. drive sprocket; 6,9. keys; 7. lubricator; 8. bearing bush; 10. fixer

The snow thrower body itself can easily be made according to the scheme, using 2 mm thick steel sheets. Rivets 4 mm in diameter and M4 screws are perfect for fastening.

Useful tip! To be able to control the height of the cleared snow, you can make a special ski underneath the design.

How to make a snowplow from a power tiller with your own hands. instructions with assembly drawings

In order to significantly reduce the time for reinstallation of the motor, you should install quick-release mounts on the homemade vehicle.

It is possible to make the harvesting aggregate on the TV-6 axe making machine. To make a snowplow for your power tiller with your own hands, it is recommended to adhere to the drawings.

• The box is made of iron sheet, the ends of which are bent in the form of skis.
• The shaft, no less than 5 cm thick, is made of a pipe.
• A gripper made of two welded U-shaped plates is welded to the box. Both plates should be rotated not 180 degrees with respect to each other.
• Self-made auger from the conveyor belt (1.5 m long and 10 mm thick). Use the jigsaw to cut 4 rings out of the tape (diameter=28cm). If there is no jigsaw, it can be replaced by a special board with two screws screwed into it.
• Such a plank is used in a circular manner. by rotating it in a circle. This method of manufacturing yields quality rings.
• In a casing made of galvanized iron, make a hole in front of the spreader and install a pipe in it. The snow spreader pipe is the pipe that will serve as the snow spreader.Holders are welded to the pipe on both sides of the spreader.

From the drawings below you can assemble both an independent snow blower machine and a single-axle tractor attachment.

How to use a power tiller with a snow thrower

Regardless of whether you have chosen to buy a snow blower for a power tiller, or use a homemade device, there is a set of rules that are recommended for working with this type of equipment. By adhering to them, you can not only prolong the life of the device, but also avoid many dangerous situations:

• Before starting work, be sure to conduct a thorough inspection of the surface on which you plan to clear the snow. Otherwise, foreign objects could get into the mechanism together with the snow, and cause a breakdown. In addition, throwing such an object a decent distance, the snow blower can cause damage to someone’s property or health;
• Be sure to take care of your own safety: clothes should be comfortable, in season, without long parts that can get into the moving mechanism. Also choose your footwear responsibly. it should not slip. In addition, it is strictly forbidden to use the snow blower without first wearing protective glasses;
• If any unexpected situation arises, first of all turn off the device completely. You can proceed to fix the problem only if you are sure that the snow blower is off;

Observe safety precautions and procedures when using the snow blower

• The snow blower attachment on your power tiller is designed to work on relatively flat surfaces. Do not use it on too steep climbs or slopes;
• According to safety rules, the distance that must be respected in the work, on the side of the throwing snow is 10 m. Make sure there are no people, cars, etc. in this area when clearing the snow.д;
• When working with wet, slightly melted snow, be sure to take breaks in the work to make sure no parts of the snow blower are clogged with snow.

If you follow these rules, a snow blower for a tiller can be considered a safe machine. The main thing to remember is that such devices do not tolerate haste and fuss. If you decide to shovel snow, allow plenty of time and be as responsible as possible.

As you can see, the annual need for snow clearance can become less tedious at quite an affordable price. Depending on your desires and capabilities, you can buy a snow blower from the manufacturer, or make it yourself. In any case, it will greatly facilitate your work and allow you to spend much less time on clearing snow than would be required for manual work.