How to change the drum on the trimmer

How to tuck line into the trimmer: a few simple tips

Thanks to modern power tools, a person is given a lot of opportunities to reduce manual labor. These innovations include the trimmer, which greatly facilitates the process of mowing and lawn care. This device reduces the time for gardening work, turning difficult physical work into entertainment. The trimmer uses a fishing line as a cutting tool. It stretches strongly and thus mows grass of almost any height. It is quite easy to operate a power tool, but the problem arises when the cutting material runs out. Not everyone will immediately figure out how to tuck the line into the trimmer. Although this is a simple operation, it is not always clear to a person who is faced with this task for the first time how to properly wind it on a reel. Moreover, the instructions do not contain information on how to choose and replace the trimmer line..

How to quickly and correctly tuck the line into the trimmer?

Once you figure out how to change the cutting material, further use and maintenance of the trimmer will be greatly simplified. To wind the trimmer line, several operations should be performed, namely:

Unscrew the nozzle by rotating the drum to the right. You will have a head in your hands with the remnants of an old thread. Open it with a screwdriver, or wring out the latch and turn the cover in the direction of the arrow. This operation should be carried out carefully, since there is a spring inside, which, straightening, can throw out all the internal parts of the drum. To change the line in the trimmer, you need to take out the spool and remove the rest of the material.
Take 5 meters of new thread and fold it in half. There is a hole in the middle of the spool where you need to insert the material. There is also an arrow indicating the direction to reel in the trimmer line. It is important to consider some points. If the spool has two holes, then half of the trimmer line should be tucked in one direction and the other in the opposite direction. When finishing inserting the material, it is better to leave 15-20 cm free.
Assemble the drum, reinstall the spring and washers. Then, while holding the spool, thread the ends of the line into the holes on the sides of the nozzle. Then put the head back in place, tightening the cutting material.

Instructions

In order to change the line, you need to remove the old one (if it was).

The reel is the part of the trimmer structure that is located inside the mower head, drum or bobbin. Heads may vary depending on the manufacturer. But this article only covers Patriot, although their mechanism is used by many other companies..

Now you need to understand how to properly remove the head from the trimmer and how to pull the drum out of it..

Instructions on how to unscrew the manual head on the trimmer are described below..

First of all, you need to clean the head from dirt and adhering grass, if it is dirty. To do this, lift the mower head up and, grasping the casing, remove the special protective cover on the drum.
The next step is to remove the spool from the drum. The reel can be easily removed even with one hand, because it is not fixed in any way inside the drum.
The drum itself is fixed in the trimmer with a bolt. This bolt must be unscrewed, after which you can easily pull out the drum. To do this carefully, you should support the drum with the spool, while unscrewing the screw counterclockwise.
Now you can pull the coil out. As mentioned above, it is not secured by anything, except for a hook with a metal shaft, so it does not need to be pulled out with force. Carefully, in a circular motion, pull the spool out of the drum.
Now it remains to remove the old fishing line and follow the following instructions.

Installation of the spool and drum in their original place is performed according to the reverse algorithm..

Before threading the line, make sure you have purchased the correct thread for the trimmer. In the event that the thread is not suitable, the consumption of fuel or energy increases, as well as the load on the engine of the lawn mowers.

In order to replace the thread itself directly, you need to prepare a piece of thread of the required size. Most often, this requires about 4 m of line. The specific figure will depend on the parameters of the thread, for example, its thickness, as well as on the parameters of the spool itself. If you cannot accurately determine the length, you can do the following: insert and wind the thread until the coil is fully charged (the line level will be compared with the protrusions on the sides of the coil). Make sure that the line sits evenly in the reel.

Do not forget that thick thread will be shorter than thin thread.

The instructions for threading the line into the spool are described below..

The prepared thread must be taken and folded in half. It should be ensured that one edge is longer than the other by 0.1-0.15 m.
Now you need to take the ends in different hands. The one that is smaller must be pulled up to the larger one so that it becomes 2 times shorter. When bending, maintain an offset of 0.15m..
Locate the slot inside the coil baffle. Carefully pass the loop you made earlier into this slot..
To continue working, it is necessary to determine the direction of winding of the thread in the bobbin. To do this, it is enough to inspect the coil – there should be an arrow on it.
If the arrowhead cannot be found, then it is quite possible that there is a written designation. An example is shown in the photo below. It is necessary to inspect the coil head. There is a direction indicator on it. However, this is the direction of travel of the coil. To get the direction of winding, you need to wind in the opposite direction.
Now you need to load the spool with line. It is worth noting that there are special guide grooves inside the coil. Follow these grooves when winding the thread, otherwise the trimmer may be damaged. At this stage, you need to charge the coil very carefully..
When the user winds up almost the entire thread, take the short end (do not forget about the 0.15m protrusion) and pull it into the hole located in the wall of the reel. Now you need to repeat this action in the same way with the other end (on the other side).
Place the reel itself in the head of the reel, before that threading the line through the holes inside the drum.
Now is the time to put the drum back in place. After that, you need to take the ends of the line with both hands and pull them to the sides. Then you need to put the lid back on (here you can safely make efforts until you hear a characteristic click).
Remained to do the “cosmetic work”. We need to see if the thread is too long. You can start the trimmer and check in practice if everything is comfortable. If the thread comes out a little long, you can cut it with scissors..

How to wind the line onto the Patriot trimmer reel?

Almost every beginner when using a trimmer is faced with the problem of changing the line. While it is very easy to change your line, you need to learn how to do it correctly. Changing the fishing line with proper skill will take no more than five minutes – you just need to constantly practice it. This article will look at changing line using Patriot trimmers as an example..

Frequent mistakes

Although winding the line is a very simple task, many beginners can wind the line incorrectly. Below are the most common mistakes.

Many people, when measuring a thread, think that 4 m is a lot. Because of this, people often measure less, and, accordingly, they do not have enough line. Do not be afraid to measure out a lot, because you can always cut off the excess.
In a hurry, some people do not follow the threading grooves inside the spool and wind the thread randomly. This will cause the line to come out of the reel and may even cripple.
For winding, use only the appropriate line. This mistake is the most common one. You need to monitor not only the thickness and volume of the line, but also its type. You should not use the first line that comes across for wrapping, which will not meet the goals. For example, you do not need to use a thread on young grass if you need to mow dead wood..
Do not turn on the device until it is fully wound and collected. Although this is obvious, some people do this in order to check if everything is done correctly..
In no case should you confuse the direction of refueling, as this will overload the engine, and it will soon come out of working condition..

It is quite common for beginners to make mistakes, so you need to follow the tips given in this article..

See below for how to replace the line on the Patriot trimmer..

How to wind the line on the trimmer correctly

A garden trimmer is a useful tool that makes life much easier for any gardener or private home owner. The grass just rushes in the summer, especially after the rains, so you can’t go anywhere without it. But over time, sooner or later, the line in it will end, and it will be necessary to insert a replaceable skein of new line. Some summer residents get stumped – how to do it yourself? So our article will help them..

Changing the line on the trimmer

This article will tell you how to change the line on the trimmer. For some people, this job may not be easy. But the step-by-step instructions that are available here will help you in this matter..

So the first thing to do is remove the gear cover. We combine the hole on the side of the curly lower washer and the axial recess, insert a screwdriver to fix the shaft from scrolling. Now unscrew the nozzle. The thread on the shaft, as a rule, has a reverse thread, take this into account when unscrewing.

Next, the disassembly of the nozzle follows. There, the lid is secured with latches through the holes. So you just have to push these clips into the holes and the cover will come off. If the attachment has automatic / semi-automatic line feeding modes, it means that there is a spring inside, which can simply fly out when the lid is opened, be prepared for this. We lay out all the removed parts neatly in order..

Now it’s time to take the fishing line and unwind 5 meters from it, cut off this piece. Pay attention to its thickness, do not wind a line of greater thickness on the unit than specified in the manual for the tool. Otherwise, there will be an increased load on the engine and higher fuel consumption during operation. We bend the measured line in half to find the middle and get a loop.

There are a couple of notches in the middle of the coil, sometimes these are not notches, but holes located opposite each other. With a loop we cling to one of the grooves and wind the fishing line counterclockwise. If the reel has 2 compartments, then we wind each end of the fishing line on them separately. Leave the last 15-20 cm free and clamp them while in the recesses of the coil.

We assemble the device again, pull the free ends of the fishing line into the holes on the body. We put on the cover, snapping the latches into their grooves. Now you can pull out these loose ends of the line..

It remains only to attach the working node in place, as in the first paragraph. Do not forget about reverse rotation on screwing.

Now you can learn how to wind the line around the trimmer. Actually, the whole process was detailed above. No time-consuming operations requiring the presence of specialists. Your lawn mower is ready for use again.

How To Change Line In A Grass Trimmer

How to change the line in the trimmer and which one is better to choose

Since we saw the choice of a trimmer in the previous article, now we will tell you how to correctly fill the trimmer with fishing line, and which one is better to choose based on the criterion of work.

After you have purchased a trimmer and began to use it intensively, at some point the question of changing the line will arise, since this is the most wearing element in the tool, the rich operation of the trimmer will lead to frequent replacement of consumables.

Replacing the line on the lawn mower.

How to wind the cutting line yourself on the reel of a lawn mower (trimmer)

What you need to know about trimmer line

A fishing line is a consumable that is made of nylon and serves as a cutting device. By means of this equipment, the grass is cut, which is ensured by rotating the tool head at a high frequency. This material has different thicknesses, which depends on its use on the corresponding tools low-power electric (from 1 to 1.6 mm), electric from 500 W (2-2.4 mm) and gasoline trimmers with lawn mowers (from 2.4 to 3 , 2 mm).

The more powerful the tool, the correspondingly thicker the cutting equipment should be. This affects not only the quality of the grass cut, but also the service life of the material. If you are wondering how to wind the trimmer coil, then it is time to change and recharge the tool. With the onset of spring, this question is becoming more and more popular, so it’s time to figure out the step-by-step instructions for replacing the line in the trimmer reel..

A garden trimmer is a useful tool that makes life much easier for any gardener or private home owner. The grass just rushes in the summer, especially after the rains, so you can’t go anywhere without it. But over time, sooner or later, the line in it will end, and it will be necessary to insert a replaceable skein of new line. Some summer residents get stumped – how to do it yourself? So our article will help them..

How To: Replace Cordless String Trimmer Spool

What types of woods are there

The most common type of line that fits almost all reel types is round cord. How to change the line correctly in the trimmer, the line must be changed. for thick grass. How to remove the head from How to change the line in the trimmer. Therefore, you first need to open it. This is an ordinary fishing line, suitable for mowing succulent grass, but it will be much more difficult to mow dead wood with it, and even more so it will not cope with bush.

As a rule, the diameter that can be used to cut young grass does not exceed 1.6 mm. How to remove, change the line and is the only correct solution for mowing grass c. How to change the line in the trimmer and Choose the line for the dry grass trimmer just for. The thicker the thread, the more coarse grass it is able to overcome.

There are fishing lines with sharp edges in the form of an asterisk or a square, this option is more adapted to mowing dry grass just due to the existing sharp edges, but its disadvantage is greater wear and is inferior in strength to a round cord.

How to thread the line into the trimmer spool

In order to wind the line, it will take about 10-15 minutes. What is a trimmer coil? Plastic body with a cassette inside, on which there is a special hook for easy winding of the fishing line. Almost all trimmer reels have a similar fastening principle, this is a central screw-button, when pressed, it becomes possible to pull out the line of the required length. The photo below shows a few examples of different trimmer spools..

How does a line head work on a lawn mower why you need to know how it works

Depending on the manufacturer, the heads differ structurally not only externally, but also internally. Most drums have a pressure spring inside (semi-automatic and automatic). Above is an instruction on how to disassemble the trimmer head without a spring, i.e. on the head of the manual type. The principle of dismantling a semi-automatic head with a spring inside is almost identical to the instructions described above..

The principle of operation of the semi-automatic trimmer coil is as follows:

Inside the head there is a coil, which is fitted on the slots, which prevent its free movement.
A spring acts on the coil, which presses it against the splines in the cover structure
A fishing line is wound on the tip, the length of which depends on the tool itself. Typically this length is between 1 and 4 meters.
During the performance of work, if it is necessary to increase the length of the line, the protruding part of the drum is pressed, whereby it disengages from the splines. In this case, the line is unwound from the drum, increasing in length
After releasing the required amount of fishing line, release the pressure and continue cutting the grass

The advantage of a tool with a line is that this consumable does not require sharpening, compared to metal discs. In addition, if a stone or a tree comes across on the way, the line simply breaks off, without negatively affecting the gearbox and engine of the tool, as is the case with metal cutting discs..

Knowing the design and device of the types of mowing or trimmer heads, it is necessary to go on to consider the process of threading the line into the trimmer spool. After all, it is this very moment that causes difficulties for most owners of special tools..

How to wind line on a trimmer reel: key points

A gasoline or electric trimmer is an indispensable tool in the arsenal of a modern summer resident or owner of his own home..

Thanks to these garden tools, even a large garden plot can be mowed with ease. After purchasing this tool and performing several mows, many people think about how to properly wind the line on the trimmer reel. For an inexperienced user, the first operation to replace it will seem problematic and time-consuming, since the developers often do not fully reflect the instructions for replacing the fishing line in the operating manual..

How to wind the line correctly on the trimmer spool

Instructions

In order to change the line, you need to remove the old one (if it was).

The reel is the part of the trimmer structure that is located inside the mower head, drum or bobbin. Heads may vary depending on the manufacturer. But this article only covers Patriot, although their mechanism is used by many other companies..

Now you need to understand how to properly remove the head from the trimmer and how to pull the drum out of it..

Instructions on how to unscrew the manual head on the trimmer are described below..

First of all, you need to clean the head from dirt and adhering grass, if it is dirty. To do this, lift the mower head up and, grasping the casing, remove the special protective cover on the drum.
The next step is to remove the spool from the drum. The reel can be easily removed even with one hand, because it is not fixed in any way inside the drum.
The drum itself is fixed in the trimmer with a bolt. This bolt must be unscrewed, after which you can easily pull out the drum. To do this carefully, you should support the drum with the spool, while unscrewing the screw counterclockwise.
Now you can pull the coil out. As mentioned above, it is not secured by anything, except for a hook with a metal shaft, so it does not need to be pulled out with force. Carefully, in a circular motion, pull the spool out of the drum.
Now it remains to remove the old fishing line and follow the following instructions.

Installation of the spool and drum in their original place is performed according to the reverse algorithm..

Before threading the line, make sure you have purchased the correct thread for the trimmer. In the event that the thread is not suitable, the consumption of fuel or energy increases, as well as the load on the engine of the lawn mowers.

Do not forget that thick thread will be shorter than thin thread.

The instructions for threading the line into the spool are described below..

The prepared thread must be taken and folded in half. It should be ensured that one edge is longer than the other by 0.1-0.15 m.
Now you need to take the ends in different hands. The one that is smaller must be pulled up to the larger one so that it becomes 2 times shorter. When bending, maintain an offset of 0.15m..
Locate the slot inside the coil baffle. Carefully pass the loop you made earlier into this slot..
To continue working, it is necessary to determine the direction of winding of the thread in the bobbin. To do this, it is enough to inspect the coil – there should be an arrow on it.
If the arrowhead cannot be found, then it is quite possible that there is a written designation. An example is shown in the photo below. It is necessary to inspect the coil head. There is a direction indicator on it. However, this is the direction of travel of the coil. To get the direction of winding, you need to wind in the opposite direction.
Now you need to load the spool with line. It is worth noting that there are special guide grooves inside the coil. Follow these grooves when winding the thread, otherwise the trimmer may be damaged. At this stage, you need to charge the coil very carefully..
When the user winds up almost the entire thread, take the short end (do not forget about the 0.15m protrusion) and pull it into the hole located in the wall of the reel. Now you need to repeat this action in the same way with the other end (on the other side).
Place the reel itself in the head of the reel, before that threading the line through the holes inside the drum.
Now is the time to put the drum back in place. After that, you need to take the ends of the line with both hands and pull them to the sides. Then you need to put the lid back on (here you can safely make efforts until you hear a characteristic click).
Remained to do the “cosmetic work”. We need to see if the thread is too long. You can start the trimmer and check in practice if everything is comfortable. If the thread comes out a little long, you can cut it with scissors..

How to wind the line onto the trimmer spool

First, the head must be disassembled, for this we press with our fingers on two latches, which are located on the body of the head at 90 degrees from the entrance, and remove the top cover.

After you remove the top cover, you need to get the cord holder, while being careful not to lose the spring, as well as the tap holes through which the line is fed. Measure out the correct amount of line and fold it in half.

Place the folded line in the middle over the holder (there is a special slot in it) and start winding the cord so that each mustache of the two falls into its own compartment of the holder.

Leave a free length of the mustache about 15 cm, fix them in the special slots of the holder and install it in the lower part of the head.

Pull the whiskers out through the eyes and install the top head cover, aligning the side latches.

As a result, you got the head correctly seated with the fishing line, you can continue to work.

Replacing a Weed Eater String (String Trimmer Line) | The Home Depot

And finally, a video on how to quickly thread the line into the trimmer head.

Winding process

If your coil is designed to work with only one tendril, then it’s simple. You need to unwind 2-4 m of fishing line (depending on the size of the reel), find a fixing hole for the line on the inside of the reel, insert one end of the line there and start winding the line in the direction opposite to the direction of rotation of the reel on the trimmer. On the inside of the reel, they usually indicate with an arrow in which direction to wind the line. Having reeled the fishing line, we leave a small piece of it unwound in order to expose it outside. We fix this piece in a special groove located on the inner part of the reel and designed so that the line does not unwind at the time of collecting the reel. If there is no such groove, then you will have to hold the fishing line with your finger to prevent it from unwinding during the further collection of the coil. Next, we take the outer part of the coil and thread the outer piece of fishing line into the existing hole, assemble and put the coil back on the trimmer.

If the coil is designed to work with two antennae, then do the following. On the inside of the reel, we look at how many grooves there are for winding the fishing line. There may be one or two of them. If there is only one groove, then both antennae are wound along this one groove. If there are two grooves, then each antenna is wound along its own groove. A reel with one groove should have a through hole through which the line is threaded. We unwind 2-4 m of fishing line, thread it through this hole so that it sticks out equally on each side of the fishing line. And we simultaneously wind both antennae of the fishing line in the same direction, opposite to the direction of rotation of the coil on the trimmer and coinciding with the direction indicated by the arrow on the inside of the coil. We leave a little of the fishing line unwound, fix the resulting ends in special grooves, and if they are not there, we hold them with our fingers. We pass both ends into the existing holes on the outer casing of the coil. Assembling the coil and attaching it to the trimmer.

If there are two grooves, fold a piece of fishing line 2-4 m long in half, insert the loop obtained at the place of the fold into the groove between the two grooves, and simultaneously wind both ends of the fishing line along its own groove. Further actions are similar to the previous option..

There are also reels in which the fishing line is threaded through a through hole on the inside. After that, the ends of the line, without winding, are threaded completely through the holes on the outer body of the reel, collect the reel and begin to rotate the button, which is usually pressed, in order to release the line during operation as it wears out. Rotate the button – the fishing line itself is wound inside. At the same time, it will not work to turn it in the “wrong” direction, since it can only rotate in one direction. If you get used to it, you can wind fishing line on such a reel without even disassembling it – you just need to combine the through hole of the inner drum with the holes on the outer body of the reel, and then thread the line through them.

That’s all on this issue. Happy winding!

More than 200 types of trimmers in one place at the lowest prices. Click and watch

Now, having removed and disassembled the coil, we proceed, in fact, to winding.

Winding the line to the trimmer

Measured and accurate dismantling of the spool from the spit coil makes it possible to go directly to the winding of the line. The design features of the head, the number and location of the fixing holes dictate the sequence of actions when performing this operation, and also determine the methods used. Today there are several types of reels, depending on the number of line antennae and the methods of threading it:

Trimmer head with one working mustache;
A bobbin with two line tendrils;
Auto winding reel.

Single-barbed trimmer spool

Single-barb lawn mowers reel

Many owners and experts note the ease of use and ease of refueling the single-whisker bobbin. Depending on the manufacturer, the length of the threaded line can vary from 2 to 5 meters. The end of the line is inserted into the head into a special technological groove or hole, and the winding is carried out in the direction opposite to the working rotation of the bobbin. Most reels have arrow marks on the outside of the body that indicate the direction of travel of the trimmer reel..

After winding, you need to leave a free end of 15-30 cm to increase the centrifugal force, which is decisive when removing the trimmer line in automatic and semi-automatic spools. We pass the left end through the working hole of the coil and assemble the head.

Sources:

http://stroy-podskazka.ru/trimmery/namotat-lesku-patriot/
http://www.vse-dachi.com/kak-namotat-lesku-na-trimmer-pravilno.html
http://sc-master.ru/raznoe-2/kak-menyat-lesku-v-trimmere-dlya-travy-kak-pomenyat-lesku-v-trimmere.html
http://yasenevo-flowers.ru/navesnoe-oborudovanie/kak-pravilno-namotat-lesku-na-katushku-trimmera.html