How to change the line on a STIHL gasoline trimmer

Changing the fishing line in the STIHL fs 55 trimmer

Warranty run out of factory filling trimmer for grass will inevitably require substitution of fishing line. Having a very rough idea of how to tuck the line into the grass trimmer reel without helping others, newcomers take on this job without any hunting. How to wind the line on the grass trimmer spool, how to tuck the line into the grass trimmer spool. Autocut for STIHL grass trimmer STIHL fs 55 line feed into the grass trimmer spool 2 parts winding line on. But with some ability to master this simple science is not difficult, and presented below a similar annotation is very easy this process.

Performing line winding

Hastily completed disassembly of the bobbin spool without losing its parts allows you to move on to the main task. winding up the line in the spool. Technological features of the bobbin’s construction and the number of working eyes determine the sequence of actions.

Reel with one working spool pin

The most common option and an easy sequence of actions:

  • The size of the bobbin and the length of the unique factory winding determine the recommended length of fishing line for winding. 25 m.
  • One end of the line is inserted into the fixing technological hole located inside the bobbin.
  • The line is wound on the reel in the opposite direction to the rotation of the bobbin on the trimmer product. usually, on the inside of the reel an arrow indicates in which direction the winding is carried out.
  • A small piece of fishing line is left free to be fed out. it is secured in a special groove on the inside of the bobbin created to hold the winding when assembling the bobbin in working order.
  • The leftover end of the fishing line is passed through the hole on the outside of the bobbin.
  • The halves of the reel are assembled and put on the rod of the trimmer.

How to put the line in a STIHL mower.FS-38

i got the mower out of the shed but the line was missing, i had to put a line on it and i took a small one off on occasion

Reel with two working tendrils

In this type of bobbin you should determine the number of grooves for winding the line lying on the inside of the spool:

For both cases you need 2-3 m of fishing line. In single-cable spools the line is pulled through the through hole, its ends (tendrils) are folded together and aligned, then wound in the opposite direction of rotation of the bobbin on the rod. inside the arrow usually indicates the correct winding direction. If there are fixing grooves, the ends of the fishing line are pushed through or held by the fingers of your free hand, put it through the hole in the outer half of the bobbin, close the bobbin and fasten it to the rod of the trimmer product.

The difference of winding the line in the double-channel reels is that initially a piece of line with a length of 2-5 m is folded in half (to determine the middle fold), and the loop of the fold is inserted in a special groove between the grooves. Both tendrils of the fishing line are wound each on its groove, fixing the tendrils and reel assembly is similar to the variant with one groove considered above.

How to change a line on a trimmer, Moto Mower electro Mower.

Doing this procedure for the first time may seem lengthy and quite time consuming, but with time and experience this task will be much faster and easier.

The video below will visually show how to tuck the line into the grass trimmer reel and correctly wind it up. this operation is not anything complicated and with some patience will surely succeed:

A REVIEW OF EXCEPTIONAL HANDYMAN AND REPAIR TOOLS AND EVERYTHING FOR GARDENS, HOME AND CAT.

The dust cap wiped off the jam nut body and the saw fell out. The guide holes are clogged with grass and soil. Manual soaking and bobbin return doesn’t help.

I really wanted to save money.

Gear Replacement in a STIHL Fse 52 Trimmer

DAEWOO Power Products DABC 420 grass trimmer

TRANSMISSION FBC-451/2200 gasoline grass trimmer

Gas trimmer for grass-reducer, 26mm, square, Sturm!

Electric grass trimmer FORWARD FGT-230/1500

Carver GBC-043MS Grass trimmer 1250 W / 1,7 l.с.

Changing a line in your trimmer: 2 easy ways

Grass trimmer. a necessary and useful tool for the cottage and private home. Many people own and actively use it, but not everyone knows how to change the line in a trimmer, especially at first.

In this instruction, we’ll go over the entire replacement process step-by-step. Getting ahead of myself, there are two ways of threading the trimmer spool. There is no fundamental difference. the difference is that in the first case, you will fill in one piece of fishing line, folded in half, while in the second case there will be two pieces of such fishing line.

The first way

Prepared section (in this case it is 4 meters) is bent approximately in half. one section should be 15-20 cm longer, and inserted into a special slit located on the dividing partition.

One way is to wind up the line in the previously determined direction. This is done in tension, the line is accurately distributed. The longer section should be wound into the section that is closer to the button.

There are designs in which the division of the reel into two sections is not provided. This does not change anything, the line is wound in a similar way. You just need to make sure that the sections do not overlap each other.

The section at the bottom of the reel should be the first to finish, i.e.е. the one which is closer to the fixing holes.

This tip is placed in the appropriate diameter hole. The line is securely fastened.

Reel in the longest part for another half-turn. There it is similarly fixed. In doing so, the section crosses the other section of the spool.

One more half turn of the line is rewound for the longest part

The fixed ends of the wound line are inserted into the holes in the body of the grass trimmer bobbin.

Insert the wrapped line ends into the holes in the grass trimmer’s bobbin case

The coil is attached to the body. Tighten the ends of the line with force so that the line, previously fixed in the holes of the reel, pops out of there. This can easily be identified by the characteristic sound (click).

Snap the reel with the button into the grass trimmer bobbin case.

The reel with the button is snapped into the body of the grass trimmer bobbin

The line is exchanged successfully. At this point, you need to set back on the grass trimmer and you can start mowing the grass.

It should be repeated, the bobbin with a grass trimmer does not need to be removed. this was done to clarify the process of changing the fishing line. You can disassemble the bobbin in place, reel it in and put it back.

The tips, so they don’t hit the hood of the grass trimmer can and should be trimmed.

Carburetor on petrol grass trimmer UNION BTS-9252L, BTS-9256L

TRANSMISSION FBC-452/2200 petrol grass trimmer

A universal spool for a chain saw

TRANSMISSION FBC-522/2600 petrol grass trimmer

The reel is worn out from long use.

The first repair project is to solder a new extension cover made of nylon or plastic.

To keep the saw in the hole, it was necessary to clamp it in the chuck of the lathe and cut a slot under the retaining ring with a cutter 1 mm deep and 2 mm wide.

I bent the retaining ring on the cut water tube from the bicycle needle and removed the extra space.

After a simple repair, I put the head on the bush cutter, put on my shoe, tucked in the fishing line and went into the garden to test. It all works! Right! I clicked on the updated speech. The fishing line went on. After mowing, the dust remains in place. The planned surfaces are not clogged with grass and soil.

The successful solution within the next hour was re-implemented on the second worn out head. Now I have a spare!

If you look closely at the attached drawings, you can guess from the bronze billet joint prosthesis tube plus tube.

How to rewind your Stihl trimmer.

Or even with a protective cap on the trunk. Then the groove with the retaining ring is unnecessary.

Types of trimmer heads

The grass mowing head is a cylindrical housing in which a spool (bobbin) is inserted with a fishing line (cord) threaded into it. This design can be installed on both gasoline and electric trimmers. The heads differ in the way the cord is threaded and fed and come in 3 types.

  • Automatic. The filament is fed in after the user has lowered the engine speed. Although automatic line feed is useful for higher production volumes, it has the disadvantage that it consumes more filament.
  • Semi-automatic. This type of head does not require the user to perform complex manipulations. The way they work is that the cord is lengthened automatically while the machine is running at full speed. Simply knock the grass trimmer head lightly on the ground (this removes the cord lock), and the line thanks to the centrifugal force is pulled out of the bobbin and then cut to the desired length by the blade located on the protective cover.
  • Manual. Extending the cord requires the machine to stop, and then the line is pulled out manually.

Given the above, semi-automatic bobbins are the best choice. It should also be borne in mind that grass trimmer spools can be single string (used only for grass trimming) and double string, which are used for mowing tall grass and small, with thin stems of bushes.

Preliminary preparation

First, for winding line requires removing the spool (bobbin, spool) with a trimmer for grass. certain actions will depend on the difficulty of configuration and type of product itself:

  • Small electronic grass trimmers with the working arrangement of the motor and spool in the lower part, usually have on both sides of the reel side buttons. When they are pressed simultaneously, the higher part of the spool, together with the internal contents for winding the line, detaches, while the lower part remains on the trimmer. Disassembly of the bobbin is better to create on a flat smooth place, so that the spring included in the design does not pop out and not lost;
  • electronic and gasoline grass trimmers with a curved shaft without the ability to set the blade, usually have a reel with a special wing nut: with similar designs, hold the bobbin in place with one hand and turn counterclockwise the wing nut fixing the bobbin on the shaft with the other hand. How to tuck the line into the grass trimmer? How to tuck the line into the grass trimmer reel. It is clear how to charge the line on the grass trimmer. After disconnecting the nut, the entire spool is removed.
  • Electronic and gasoline grass trimmers with the ability to install a knife on a straight shaft (for example, STIHL grass trimmers) under the bobbin has a hole. To immobilize the boom a screwdriver or other suitable object is inserted into the hole and a slight twisting action is taken to assure that the screwdriver goes into the hole and the bobbin is locked in place. After that the spool body is rotated clockwise (with the left thread) and removed from the grass trimmer.

For the second and third version of the spool, depending on the design, disassembled by different methods. For reels with a wing nut, unscrew the wing nut, and for reels with latches, press the latch latches and one part of the reel is released from the other part. How to reel a line in how to do it right cheap line. 2. At your site. If the halves of the bobbin are connected by thread, it is enough to turn them by hand in opposite directions until they are completely uncoupled.

Automatic line winding on a spool

There is a type of reel with an automatic mechanism that winds the line by itself. All you need to do is reel in the line correctly. The line is passed through the hole on the inside of the housing, its tendrils without winding are passed through the hole on the outer housing, the bobbin is assembled, and when you turn the winding button, the line inside is wound independently. With such a bobbin it is impossible to wind it incorrectly: the mechanism itself will determine the correct direction, because it can only turn to one side.

Since the choice of grass trimmer we reviewed in. today we will tell you how to correctly fill the trimmer for grass, and which one is better to choose based on the conditions of work.

After you bought a grass trimmer and started to use it actively, sooner or later there will be a question of replacing the line, because it is the most wearing element in the tool, the intensive use of trimmer for grass will lead to frequent replacement of the consumable material.

How to wind the line on the grass trimmer spool semiautomatic

Replacing the grass trimmer’s fishing line with step-by-step instructions will allow even an inexperienced lawnmower owner in such matters to perform quite a complex job.

However, before you begin work on replacing the line on your trimmer, you must ensure that it is safe to do so. In particular, take precautions against careless or unintentional activation of the lawnmower:

  • Prevent unintentional starting,
  • Remove the battery (if used),
  • Place the tool in a suitable area to work.

It is convenient to replace grass trimmer’s fishing line when the mower is lying on the table and the person who does the trimmer’s line replacement has an opportunity to step up to the tool from any side.

Grass trimmer head cover removal

The first step in disassembly is removing the grass trimmer head cover. Using the “Black and Decker” and other trimmer models as an example, to remove the cover it is usually enough to apply some pressure to push the locking tab, which is located on the side of the head.

On some models of lawnmowers initially provides for the removal of the grass trimmer head, for which a hexagon wrench included in the tool kit is used. The head is usually held by two or three screws, which are accessed through the side holes of the rear decorative cover.

The cover of the head, where the filament spool is installed, is usually held in place by a latch. It is enough to squeeze the tongue-latch with some effort and slightly turn the cover, after which the cover is easily removed At the moment of squeezing the tongue-latch it is necessary to slightly turn and lift the cover of the grass trimmer head to remove the winding drum.

Step two: remove the spool (spool) with the line

The next step of the process is to remove the spool with the line from the inside of the head. You need to turn the head with the open side to see the line and spool. On the side of the head, find two recesses (eyelets), through which the line is led out.

Release the line from the holes by turning the reel. Then carefully remove the spool from the head area. The spooling reel of some models is mounted on a spring. This is a point to bear in mind during the extraction operation.

Procedure for extracting the grass trimmer reel with fishing line from the inner area of the head: 1. head complete with reel; 2. extracting carefully with a small axial turn; 3. extracted parts The old fishing line is completely removed from the reel. To remove the old grass trimmer line, you need to remove the line from the hinges and pull the free end. This method removes all old winding. The same process is repeated on the second section of the drum. It is recommended that the handyman wear gloves when working.

The design of the line in the mower

The design of the element, on which the kapron thread is wound, is very simple. This element is called the spool. There are two “tracks” in it, the upper and the lower one. Between these tracks there is a special partition with a notch. A fishing line is wound on these tracks. It must first be pulled through the notch.

In order to be able to pull out the spool without obstacles, it is necessary to unscrew the special button, which is located on the body of the mower.

The above-mentioned unit can be made with your own efforts, and this article will tell you how to construct a lawnmower from a grass trimmer with your own hands.

How to wind the line on the grass trimmer

Grass trimmer fishing line replacement with step-by-step instructions will allow even an inexperienced in such matters lawnmower owner to perform quite a complicated job.

However, before you begin work on replacing the fishing line on your trimmer, you must ensure the safety of the work. In particular, measures should be taken to protect against careless or unintentional activation of the lawnmower:

  • prevent spontaneous start-up,
  • remove the battery pack (if used),
  • Place the tool in a suitable place to work.

Work on the replacement of the grass trimmer line is convenient to perform when the mower is lying on the table, and the master, who performs the replacement of the grass trimmer line, has the opportunity to approach the tool from any side.

Grass trimmer head cover removal

The first step in disassembly is to remove the grass trimmer head cover. On the example of models of trimmers “Black and Decker” and others, to remove the cover is usually enough to apply some force to push the latch-latch, which are located on the side of the head housing.

On some models of lawnmowers, the grass trimmer head must first be removed using the hexagonal key supplied with the tool. The head is usually held by two or three screws, which are accessed through the side holes of the rear decorative cover.

The head cap, where the line reel is mounted, is normally held in place by a latch tongue. It is enough to squeeze the locking tab with some effort and twist the cover, after which the cover is easily removed At the moment of squeezing the locking tab you need to slightly turn and lift the cover of the grass trimmer head to remove the winding drum.

Step two: Removing the spool of fishing line

The next step in the process is to remove the winding drum with fishing line from the inner area of the head. You need to turn the head open side to see the line and spool. On the side of the head find two recesses (eyelets), through which the line is led out.

Release the fishing line from the holes by turning the reel. Then carefully remove the spool from the head area. Some models are winding reels mounted on a spring. This point must be taken into account when carrying out the extraction operation.

Procedure for extracting the grass trimmer spool with fishing line from the inner area of the head: 1. head complete with spool; 2. extracting gently with a slight axial turn; 3. extracted parts The old fishing line is completely removed from the spool. To remove the old line of the grass trimmer, you need to remove the line from the loops and pull the free end. This method removes all old spooling. Repeat the same process on the second reel section. It is recommended that the technician wear gloves when performing the operation.

How to wind the line correctly on the grass trimmer: step-by-step guide and video instructions

A beautiful lawn will only look really well-maintained if the grass is regularly cut. The grass trimmer is best suited for complex areas. Any machine owner sooner or later will face the problem of how to wind the line on the spool, because incorrect actions can not only reduce the quality of mowing, but also withdraw equipment from service. In today’s Homius review, we’ll cover all the ways and nuances of replacing a fishing line and the specifics of choosing a consumable.

Grass trimmer reel design

Mowing heads for trimmers come in different designs, both simple and complex. The picture below shows a demounted semi-automatic trimmer head from a Husqvarna brushcutter (Husqvarna).

This type of head is found on most STIHL, Patriot, Champion, Bosch, Huter, and other chain saws and power trimmers. The design of the mowing head is quite simple. It includes the following parts:

  • The base of the mowing head;
  • button for semi-automatic filament feeding;
  • bobbin (spool) into which the line is threaded;
  • spring;
  • The other parts of the controller board need to be voltage-measured;
  • trimmer head cover;
  • fishing line (cord).

There are also simpler trimmer heads, shown in the following photo.

All of these nozzles do not allow you to change the length of the line in semi-automatic mode (after pressing a button). If the cord breaks, you have to stop the mower and change it manually.