How to Connect an Angle Grinder to a Battery • CIMFLOK.COM

Meet the tester

First of all, we will briefly tell you what is on the front panel of the measuring device and what functions can be used when working with the tester, after which we will tell you how to measure resistance, current strength and voltage in the network. So, on the front side of the digital multimeter are the following notation:

OFF. the tester is turned off;
ACV. alternating voltage;
DCV. constant voltage;
DCA. direct current;
Ω is the resistance;

You can visually see the appearance of the electronic tester in front:

Perhaps you immediately noticed 3 connectors for connecting probes? So here you need to immediately warn you that it is necessary to correctly connect the tentacles to the tester before the measurements. The black wire is always connected to the output labeled COM. Red according to the situation: in order to check the voltage in the network, current strength up to 200 mA or resistance. it is necessary to use the “VΩmA” output, if you need to measure the current value above 200 mA, be sure to insert the red probe into the socket marked “10 ADC”. If you do not take this requirement into account and use the “VΩmA” connector to measure high currents, the multimeter will quickly fail because the fuse will burn!

There are also old-style instruments. analogue or, as they are commonly called, analogue multimeters. The model with the arrow is almost never used, because such a scale has a higher error, and besides, it is less convenient to measure voltage, resistance and current strength on an arrow display.

If you are interested in how to use a pointer multimeter at home, we immediately recommend watching a visual video lesson:

We will talk more about how to use the more modern digital model of the tester further, having examined the step-by-step instructions in the pictures.

Measure voltage

To independently measure the voltage in the circuit, you must first turn the switch to the desired position. In a network with alternating voltage (for example, in a socket), the switch arrow must be in the ACV position. The probes must be connected to the COM and “VΩmA” jacks. Next, select an approximate voltage range in the network. If at this stage there are difficulties, it is better to set the switch to the highest value. for example, 750 Volts. Further, if a lower voltage is displayed on the display, you can turn the switch to a lower level: 200 or 50 Volts. Thus, reducing the setting to a more suitable one, you can determine the most accurate value. In a constant voltage network, use a multimeter in the same way. Typically, in the latter case, the switch is best set to around 20 volts (for example, when repairing car electricians).

A very important nuance that you should be aware of is that you connect the tentacles to the circuit in parallel, as shown in the picture:

Video: How to Connect an Angle Grinder to a Battery

Here, by this technique, you need to use a multimeter to determine direct and alternating voltage in an electrical circuit. As you can see, there is nothing complicated, the main thing is not to touch the exposed parts of the tentacles with your hands, otherwise you will not be able to avoid electric shock. By the way, you can also use an indicator screwdriver as a voltage indicator!

Measure current

In order to independently measure the strength of the current in the circuit with a multimeter, it is first necessary to determine whether direct or alternating current flows through the wires. After that, you need to find out the approximate value in Amperes to select a suitable socket for connecting a black probe. “VΩmA” or “10 A”. We recommend that you initially insert the probe into the connector with a higher current value and if a smaller value is displayed on the display, switch the plug to another socket. If, again, you see that the measured value is less than the setpoint, you must use a range with a smaller value in Amperes.

We draw your attention to the fact that if you decide to use a multimeter as an ammeter, you need to connect the tester to the circuit in series, as shown in the picture:

Measure resistance

Well, the safest thing in relation to the safety of the multimeter will be to use a device to measure the resistance of circuit elements. In this case, you can set the switch to any range of the "Ω" sector, and then select the appropriate setting for more accurate measurements. A very important point. before using the device to measure resistance, be sure to turn off the power in the circuit, even if it is a normal battery. Otherwise, your tester in ohmmeter mode may show an incorrect value.

Most often, it is necessary to measure resistance with a multimeter when repairing household appliances with your own hands. For example, if the iron does not work, you can measure the resistance of the heating element, which, most likely, has failed.

By the way, if when measuring resistance on a circuit section with a multimeter, you saw the value “1”, “OL” or “OVER” on the board, then you need to turn the switch to the range above, because at the selected setting, overload occurs. At the same time, if “0” is displayed on the dial, move the tester to a smaller measurement range. Remember this moment and it will not be difficult to use a multimeter when measuring resistance!

We use the proverbial

If you look closely at the front panel of the tester, you can see some more additional functions that we have not yet talked about. Some of them use only experienced radio technicians, so there is no reason for a home electrician to talk about them (anyway, they are unlikely to be useful in everyday conditions). But there is another important tester mode that you may use. dial-up (in the picture below we indicated its designation). For example, to find a break in the neutral wire in the circuit, you need to ring the wiring, and if the circuit is closed, you will hear a sound indication. To do this, just connect the probes to the desired 2 points in the circuit.

Again, a very important nuance is that the power on the part of the circuit that you are going to ring should be surely turned off. For example, if you decide to ring the wiring in the house, for the duration of the operation, turn off the opening circuit breaker in the switchboard. Using the multimeter with the power connected is highly discouraged!