How to correct a trimmer fishing line for a trimmer.

Намотка лески в катушку-полуавтомат бензокосы. #shorts

trimmer for grass gasoline stihl how to refuel a fishing line for a trimmer. We change the fishing line for a trimmer in a trimmer (lawn mower)

First of all, to wind the fishing line, it is required to remove the coil (bobbin, spool) from the trimmer for the grass. specific actions will depend on the complexity of the configuration and the type of product itself:

  • Small electric trimmers for grass with a working location of the engine and coils in the lower part, as a rule, have side keys on both sides of the bobbin. With the simultaneous press on them, the upper part of the coil, along with the internal contents for winding the fishing line, is disconnected, while the lower remains on the trimmer. It is advisable to analyze the bobbing in an even smooth place, so that the spring does not jump out and not be lost;
  • Electric and gasoline trimmers for grass with a curved rod without the ability to install a knife, as a rule, have coils with a special lamb: in such structures, you should hold the spool in a fixed position with one hand, and rotate the fixing bobbin on the bar with a barack’s baracks. After disconnecting the nut, the whole bobin is removed.
  • Electric and gasoline trimmers for grass with the ability to install a knife on a straight rod (for example, trimmers for STIHL grass) have a hole. For the immobility of the bar, a screwdriver or another suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bob is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer for the grass.

For the second and third cases, the coil, depending on the design, are versed in various ways. In the bobbins with a lamb, lamb is twisted, in the reels with latches, latches-fixers are pressed and one part of the coil is freed from the other. If the halves of the spool are connected by thread, then it is enough to turn them with your hands in the opposite directions until they are completely developed.

Two working antennae

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

How to replace a fishing line for a trimmer on a trimmer how to wind a fishing line for a trimmer for a trimmer for grass

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.captable coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. inside the arrow is usually indicated the correct direction of the winding. In the presence of fixing grooves, the ends of the fishing line are threaded in them or hold their free arm fingers, spread into the through hole of the outer half of the bobin, the spool is closed and attached to the bar of the trimmer product.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound each in its own groove, fixing the antennae and assembly of the coil is similar to the option considered above with one groove.

The first implementation of this procedure may seem long and quite time.consuming, but over time and experience, this task will be solved much faster and easier.

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. this operation is not a complicated one and, with some patience, will necessarily be crowned with success:

Coil with one working osik

The easiest option and a simple sequence of actions:

  • The dimensions of the bobbin and the length of the original factory winding determine the length of the fishing line recommended for winding. 2 5 m.
  • One end of the fishing line is inserted into the fixing technological hole located inside the spool.
  • The fishing line for the trimmer is wound on the drum in reverse rotation of the spray in the trimmer product direction. as a rule, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
  • A small section of the fishing line is left free to output it. it is fixed in a specialized border on the inside of the bobbin, designed to keep the winding when assembling a spool in working condition.
  • The left end of the fishing line is passed through the hole of the outer part of the bobbin.
  • Half of the bobbin are collected and put on the bar of the trimmer device.

Read how to clean the air filter on the echo trimmer

How to replace a fishing line for a trimmer on a trimmer?

Replacing the fishing line of the trimmer for the grass with step.by.step instructions will even allow the owner of the lawn mowed inexpensive in such matters to do a fairly difficult job.

However, before starting work to replace the fishing line on the trimmer, it is necessary to ensure the safety of work. In particular, it should be taken protection measures against careless or spontaneous inclusion of the lawn mower:

  • Exclude spontaneous start,
  • Delete the battery (if used),
  • Place the tool on a comfortable site for work.

Can Fishing Line work in a weed eater? Find Out!

It is convenient to perform work on replacing the fishing line for the grass when the lawn mower lies on the table, and the master, who is performed by replacing the fishing line of the trimmer for the grass, has the opportunity to approach the instrument from any side.

Step Three: The Club of the Head Noner

Stretch the ends of the fishing line through a pair of oval cuts of coil. Replace both goals and a spring (if any in the design) with new elements included in the package. Bend both ends of the fishing line at right angles.

The last technical stroke of the process of replacing the fishing line on the trimmer is to put the cover on the head with subsequent fixation by pressure and slight turnover.

Let each end into the hole, which is at the base of the winding drum. Install the coil in the inner area of ​​the head with an emphasis on the spring. Put the lid, leve on the base and light pressure down with a small rotation counterclockwise, put the cover on the tongues of the latch. This is where the replacement procedure is completed.

Step one: fixing and styling

Fold the end of the fishing line in half. Place the workpiece above the coil on each side of each half of the winding area. Wrap both halves completely around the winding drum. Stretch the fishing line for the trimmer through the loop.

The procedure for preparing fishing line in the field of both wound sections of the drum. The loops are laid in specially made cutouts, after which the winding of the fishing line is performed in each area

Pull the fishing line for the trimmer enough and put the knot in the groove made on each side of the winding drum.

Remove the head of the head of the grass for the grass

At the first stage of disassembly, the head of the head of the grass is removed. On the example of the models of trimmers “Black and Decker” and others, it is usually enough to apply some pressure to squeeze the click-fixer, which are on the side of the head of the head of the head of the head of the head of the body to remove the lid to remove the lid.

Some models of lawn mowers initially include dismantling the head of a trimmer for grass, for which a playback key is used, which is included in the tool kit. The head is usually held by two or three screws, access to which is provided through the side holes of the rear decorative cover.

The head cover, where the coil with a fishing line is installed, is usually held due. It is enough for some effort to squeeze the tongue-thorough and slightly turn the lid, after which the lid is easily removed

At the time of squeezing the tongue-fixer, you need to turn slightly and raise the head of the head of the trimmer for the grass to remove the winding drum.

Read how to put a fishing line for a trimmer on a trimmer for grass correctly

How to replace a fishing line for a trimmer on a trimmer?

Replacing the fishing line of the trimmer for the grass with step.by.step instructions will even allow the owner of the lawn mowed inexpensive in such matters to do a fairly difficult job.

However, before starting work to replace the fishing line on the trimmer, it is necessary to ensure the safety of work. In particular, it should be taken protection measures against careless or spontaneous inclusion of the lawn mower:

  • Exclude spontaneous start,
  • Delete the battery (if used),
  • Place the tool on a comfortable site for work.

It is convenient to perform work on replacing the fishing line for the grass when the lawn mower lies on the table, and the master, who is performed by replacing the fishing line of the trimmer for the grass, has the opportunity to approach the instrument from any side.

Remove the head of the head of the grass for the grass

At the first stage of disassembly, the head of the head of the grass is removed. On the example of the models of trimmers “Black and Decker” and others, it is usually enough to apply some pressure to squeeze the click-fixer, which are on the side of the head of the head of the head of the head of the head of the body to remove the lid to remove the lid.

Some models of lawn mowers initially include dismantling the head of a trimmer for grass, for which a playback key is used, which is included in the tool kit. The head is usually held by two or three screws, access to which is provided through the side holes of the rear decorative cover.

The head cover, where the coil with a fishing line is installed, is usually held due. It is enough for some effort to squeeze the tongue-thorough and slightly turn the lid, after which the lid is easily removed

At the time of squeezing the tongue-fixer, you need to turn slightly and raise the head of the head of the trimmer for the grass to remove the winding drum.

Step two: extracting a winding drum (coil) with a fishing line

The next step in the process is the exhaust drum with a fishing line from the inner region of the head. You need to turn the head with an open side to see a fishing line for a trimmer and a reel. On the side of the head, find two recesses (eyelets) through which the fishing line for the trimmer is bred outside.

You should release a fishing line for a trimmer from the holes by checking the drum. Then gently remove the coil from the head of the head. The winding drum of some models is installed on the spring. This moment must be taken into account by performing the operation to extract.

The procedure for extracting a coil of a trimmer for grass with a fishing line from the inner region of the head: 1. head assembly with a coil; 2. extracting neatly with a small axial turn; 3. extracted details

The old fishing line for the trimmer is completely removed from the coil. To remove the old fishing line for grass, you need to remove the forest from the loops and pull the free end. This method is removed by the whole old winding. A similar process is repeated on the second section of the drum. The master is recommended to use gloves when performing work.

Installation of a new fishing line on the coil of a trimmer for grass

Equipping the coil with a new fishing line is performed in the reverse order. The procedure looks like it is described below, regardless of the model of the lawn mower:

Step one: fixing and styling

Fold the end of the fishing line in half. Place the workpiece above the coil on each side of each half of the winding area. Wrap both halves completely around the winding drum. Stretch the fishing line for the trimmer through the loop.

The procedure for preparing fishing line in the field of both wound sections of the drum. The loops are laid in specially made cutouts, after which the winding of the fishing line is performed in each area

Pull the fishing line for the trimmer enough and put the knot in the groove made on each side of the winding drum.

Step two: winding cutting material according to sections

The next step is to turn the fishing line in a circle of coil, observing caution. It is necessary that each half be filled with “its own” winding, exactly, without intersections. Usually on the hull of the winding drum you can see the arrows indicating the direction of winding. This moment should be borne in mind, filling the reel with a fishing line.

Step Three: The Club of the Head Noner

Stretch the ends of the fishing line through a pair of oval cuts of coil. Replace both goals and a spring (if any in the design) with new elements included in the package. Bend both ends of the fishing line at right angles.

The last technical stroke of the process of replacing the fishing line on the trimmer is to put the cover on the head with subsequent fixation by pressure and slight turnover.

Let each end into the hole, which is at the base of the winding drum. Install the coil in the inner area of ​​the head with an emphasis on the spring. Put the lid, leve on the base and light pressure down with a small rotation counterclockwise, put the cover on the tongues of the latch. This is where the replacement procedure is completed.

Boarding line refueling instructions

In order for the trimmer for the grass to work “like a clock”, you need to choose the right fishing line for a trimmer, that is, choose it taking into account the trimmer model for grass and the type of work. Two important parameters in this matter is the diameter and section.

The diameter of the fishing line must correspond to the recommended for this model (in the passport for the product it is necessarily indicated). The cross section of the fishing line is round, square, with sharp faces (pentarannik). The fishing line for a trimmer with a round section is designed for a bevel of young grass and a lawn, a square and five.grade fishing line for a trimmer will come in handy if the grass was booing and weeds have grown on the lawns.

Step.by.step instructions for refueling fishing line in a trimmer for grass

  • Drown the clamps inward to the click and remove the lid from the mowing head.
  • Take the coil carefully, it free from the holder, and now remove it.
  • Cut two identical pieces of fishing line (cut of the edge of the fishing line should be at an angle. this will facilitate the work). Take one of them and insert the end of the fishing line into a special on the coil (there may be hooks, ears, clamps). Next, wind the string in the direction of the shooter. Distribute the fishing line for the trimmer evenly, tightly. Strengthen the end of the string into a specially provided coil opening.
  • Do the same operation with the second part of the fishing line, just season the end on the coil from the opposite side.
  • Return the coil with a fishing line to a mowing head. Through the holes in the coil, pull the ends of the fishing line and season them into a special head connector.
  • Gently straighten the fishing line for the trimmer and close the lid. Cut the excess fishing line, leaving 12-15 cm. each edge.

All is ready. Trimmer for the grass is seasoned with fishing line and ready to work. Now you can gladly take for the range of your beloved meadow, a summer cottage, a house territory.

It is only important to remember that not only the quality of the work performed, but also your safety will depend on how you refuel a cutting fishing line for a trimmer for grass.

Preliminary preparation

First of all, to wind the fishing line, it is required to remove the coil (bobbin, spool) from the trimmer for the grass. specific actions will depend on the complexity of the configuration and the type of product itself:

  • Small electric trimmers for grass with a working location of the engine and coils in the lower part, as a rule, have side keys on both sides of the bobbin. With the simultaneous press on them, the upper part of the coil, along with the internal contents for winding the fishing line, is disconnected, while the lower remains on the trimmer. It is advisable to analyze the bobbing in an even smooth place, so that the spring does not jump out and not be lost;
  • Electric and gasoline trimmers for grass with a curved rod without the ability to install a knife, as a rule, have coils with a special lamb: in such structures, you should hold the spool in a fixed position with one hand, and rotate the fixing bobbin on the bar with a barack’s baracks. After disconnecting the nut, the whole bobin is removed.
  • Electric and gasoline trimmers for grass with the ability to install a knife on a straight rod (for example, trimmers for STIHL grass) have a hole. For the immobility of the bar, a screwdriver or another suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bob is fixed. After that, the coil body is scrolled clockwise (with the left thread) and removed from the trimmer for the grass.

For the second and third cases, the coil, depending on the design, are versed in various ways. In the bobbins with a lamb, lamb is twisted, in the reels with latches, latches-fixers are pressed and one part of the coil is freed from the other. If the halves of the spool are connected by thread, then it is enough to turn them with your hands in the opposite directions until they are completely developed.

We carry out the winding of the fishing line

Sentlessly completed disassembly of a spray coil without losing its spare parts allows you to go to the main task-winding into a fishing line coil. Technological features of the design of the spool and the number of working antennae determine the sequence of actions.

Coil with one working osik

The easiest option and a simple sequence of actions:

  • The dimensions of the bobbin and the length of the original factory winding determine the length of the fishing line recommended for winding. 2 5 m.
  • One end of the fishing line is inserted into the fixing technological hole located inside the spool.
  • The fishing line for the trimmer is wound on the drum in reverse rotation of the spray in the trimmer product direction. as a rule, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
  • A small section of the fishing line is left free to output it. it is fixed in a specialized border on the inside of the bobbin, designed to keep the winding when assembling a spool in working condition.
  • The left end of the fishing line is passed through the hole of the outer part of the bobbin.
  • Half of the bobbin are collected and put on the bar of the trimmer device.

Two working antennae

In this type of spools, the number of grooves for winding the fishing line lying on the inside of the coil should be determined:

For both cases, a fishing line for a trimmer 2-3 m long is taken. In a single.captable coils, the fishing line for a trimmer stretches into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the back of the rotation of the bobbin on the bar the side. inside the arrow is usually indicated the correct direction of the winding. In the presence of fixing grooves, the ends of the fishing line are threaded in them or hold their free arm fingers, spread into the through hole of the outer half of the bobin, the spool is closed and attached to the bar of the trimmer product.

The difference between the winding of the fishing line in the two-to-dancing coils is that initially a line of fishing line 2-5 m long is folded in half (to determine the middle fold), and the bend loop is inserted into a special groove between the grooves. Both strains of the fishing line are wound each in its own groove, fixing the antennae and assembly of the coil is similar to the option considered above with one groove.

The first implementation of this procedure may seem long and quite time.consuming, but over time and experience, this task will be solved much faster and easier.

The video below will clearly show how to refuel a fishing line for a trimmer to the coil of a trimmer for the grass and correct it correctly. this operation is not a complicated one and, with some patience, will necessarily be crowned with success:

Installation of fishing line

To wind the cutting thread, you must first get to the coil in which it will be fixed. To do this, first disassemble the Bobin case. There are several ways to do it.

Removing the cover from the trimmer for the grass and its disassembly

The head of the trawoks consists of several details: cover, bobbin and casing. Separate models are equipped with a spring.

The main security requirement for disassembly is a mandatory disconnection from the power supply network. The disassembly process depends on the type of fastening. It can be screw, threaded or using the “comfort” mechanism.

In the first case, it is necessary to squeeze the locks, and then remove the freed cover and remove the spool. If it has a spring, then it is also extracted from the case. Next, using the screwdriver, you need to twist the screw. Depending on the model of the trimmer for the grass, the screw may not be in the design.

The second option implies the presence of a gearbox twisting on the shaft. In the conditions of such a construct, the shaft is first fixed, and then the bobin itself is unscrewed clockwise.

In the third situation, when you have a Comfort type on your kosyl unit, it does not need to remove the braid for the grass to remove the cutting cord from the gearbox.

Winding of the cord

Installation of a new thread in a coil is a simple procedure, but it must be carried out, following a clear algorithm. First you should determine the amount of consumables, and then do the actions described below.

  • Fold the cord twice so that the difference between its ends is about 15 cm;
  • In the central side, it is necessary to detect a groove, for which a thread is harassed, pre.bent;
  • To determine the desired direction of the winding, look at the arrow-index on the bobbin;
  • Wrap a fishing line for a trimmer opposite to the direction of the arrow;
  • At the end of the laying procedure, fix the ends to the corresponding grooves opposite;
  • Cut excess length;
  • Insert the seasoned coil in place;
  • Pull the cord from the fixing grooves, tighten it and close the lid.

There is another way that implies that instead of one segment it is necessary to charge two. The cord material in this case is wound in the direction of the arrow until it reaches a level not exceeding the diameter of the coil, the same should be done for the second cell. Previously the bent end of the thread is stuck into the hole at the bottom of the bobbin.

Summing up the above, we can say the following. Each manufacturer offers a large assortment of trimmer heads. The sequence of refueling and operating rules differ for each type. In addition, do not forget about the different strings diameter. In order to make the right choice, you need to contact the instructions or to a specialist. Not only the result of the mowing will depend on this, but also the cost of using garden technology.

Instructions

In order to change the fishing line for the trimmer, it is necessary to extract the old one (if it was).

The coil is part of the design of the trimmer for the grass, which is located inside the head of the motorcosa, drum or bobbin. Depending on the manufacturers of the head can be different. But this article discusses only Patriot, although their mechanism is used by many other companies.

Now you need to understand how to properly remove the head from a trimmer for grass and how to get a drum out of it.

Instructions on how to promote a hand head on a trimmer is described below.

  • First of all, you need to clean the head of dirt and adhering grass if it is contaminated. To do this, you need to raise a motorcycle head up and, holding the casing, remove a special protective cover dressed on the drum.
  • The next step needs to remove the reel from the drum. The coil is easily removed even with one hand, because it is not fixed inside the drum.
  • The drum itself is fixed in the trimmer with a bolt. This bolt must be unscrewed, after which you can easily pull out the drum. To do this carefully, you should support the drum with a coil, while twist the screw counterclockwise.
  • Now you can pull the coil out. As mentioned above, it is not fixed in anything except a hook with a metal shaft, so it does not need to be torn off with force. Neatly, in a circular movement you should pull the coil from the drum.
  • Now it remains to extract an old fishing line for a trimmer and follow the following instructions.

Installation of the coil and drum in its former place is performed according to the opposite algorithm.

Before the process of refueling the fishing line, it is worth making sure that the thread suitable for a trimmer was bought. In the case when the thread is not suitable, the fuel or energy consumption increases, as well as the load on the motor motor.

correct, trimmer, fishing, line

In order to replace the thread itself directly, you need to prepare a piece of thread of the required size. Most often, this requires about 4 m fishing line. A specific figure will depend on the parameters of the thread, for example, its thickness, as well as on the parameters of the coil itself. If it is not possible to accurately determine the length, it can be done as follows: insert and wind the thread to such a state that the coil is completely charged (the level of the fishing line will be compared with protrusions in the sides of the coil). It is necessary to ensure that the fishing line for the trimmer sits in the coil exactly.

Do not forget that the thick thread will be shorter than thin.

The instructions for refueling the fishing line in the coil is described below.

  • The prepared thread must be taken and turned in half. It should be ensured that one edge is longer than the other by 0.1-0.15 m.
  • Now you need to take the ends in different hands. The one that is smaller must be pulled to more, so that it becomes 2 times shorter. When bending, the indentation should be maintained at 0.15m.
  • Find the slot inside the coil partition. Carefully prick the loop that turned out earlier in this slot.
  • To continue work, it is necessary to determine the direction of winding the thread in the coil. To do this, just examine the coil. there should be an arrow on it.
  • If the gunner could not be found, it is quite possible that there is a written designation. An example is given in the photo below. It is necessary to inspect the head of the coil. It has a direction indicator. However, this is the direction of the coil movement. To get the direction of winding, you need to wind in the opposite direction.
  • Now you need to season the reel with a fishing line. It is worth noting that there are special guide grooves inside the coil. When wrapping a thread, you need to follow these grooves, otherwise you can damage a trimmer for grass. At this stage, you need to charge the coil very carefully.
  • When the user winds up almost the entire thread, you should take the short end (do not forget about the protrusion of 0.15m) and stretch it into the hole located in the coil wall. Now you need to repeat this action similarly with another end (on the other hand).
  • Put the coil itself in the coil head, before that, extinguishing a fishing line for a trimmer through the holes inside the drum.
  • Now is the time to return the drum to your place. After that, you need to take with both hands by the ends of the fishing line and pull them to the sides. Then you need to put the lid in place (here you can safely make efforts until a characteristic click is heard).
  • Remained to perform “cosmetic work”. You need to see if the thread has come out too long. You can start a trimmer for the grass and check in practice whether everything is comfortable. If the thread came out a little long, you can cut it with scissors.

Frequent errors

Although the winding of the fishing line is a very simple task, many newcomers can wrap a fishing line for a trimmer incorrectly. The most common errors are presented below.

  • Many people when measuring the thread think that 4 m is a lot. Because of this, people often measure less, and they, accordingly, do not have enough fishing line. Do not be afraid to measure a lot, because you can always cut off the excess.
  • In a hurry, some people do not observe the gas stations inside the coil and wind up the thread like it. This leads to the “departure” of the fishing line from the coil and can even cripple.
  • For winding, it is worth using only the corresponding fishing line for the trimmer. This error is most common. You need to monitor not only the thickness and volume of the fishing line, but also your type. You should not use the first fishing line for a trimmer for wrapping, which will not match the goals. For example, you do not need to use a thread on the young grass, if it is necessary to mow dry.
  • Do not turn on the device until complete winding and collection. Although this is obvious, some people do this in order to check if everything is done correctly.
  • In no case should you confuse the refueling direction, as it will overload the engine, and it will soon get out of the working condition.

Beginners are quite characteristic of mistakes, so it is necessary to observe the advice given in this article.

The choice of fishing line

In order to easily wrap a fishing line for a trimmer to a trimmer coil for grass, it is worth deciding on what tasks the garden tool will perform. The thicker the thread tucked into the head, the more difficult the tasks that it can complete. It should be noted that a universal thread is often used, the width of which does not exceed 2 mm. You, in turn, can decide on the size, using the following methods:

  • get acquainted with the information set out in the instructions from the manufacturer;
  • check the suitability of the fishing line for use on your own, trying to insert it into the coil hole;
  • study the spool for information about diameters allowed for use.

Selection of fishing line for refueling a trimmer for grass can be carried out by engine type. So, for example, an overly thick thread can affect an increase in rotational resistance. Because of this, the load on the engine will increase, which will certainly affect the quality and timing of its further operation.

correct, trimmer, fishing, line

Avoiding negative consequences is easy. To do this, it must be borne in mind that for electric motors with a power of up to 500 W, a fishing line for a trimmer with a diameter of up to 1.2 mm is ideal. If you cannot get such a thread, you can use the cord by 1.6 mm. A thread with a diameter of 2 mm, in turn, is used for engines with a power of more than 1 kW. It is worth noting that the cord for 2 mm is often used for winding on a bent mower. If the gasoline device has a straight shaft, the thread should be used 2.5 or 3 mm. The thickest fishing lines are installed exclusively on devices, the power of which is equal or exceeds 1.3 kW.

The last, but no less important factor is the type of fishing cross section. When choosing it, it is worth focusing on the tasks set before the garden tool. There are several demanded cross.sectional options:

  • twisted-has a small margin of safety, which is why it suits exclusively for young grass;
  • Substitute. is characterized by sharp edges suitable for working on overgrown weeds;
  • Round. the most common section. Such fishing lines cope well with fresh grass, but they are not suitable for shrubs and dry ones;
  • rectangular, square and star type of cross section-due to low strength, are used to work on lawns.

The most durable and universal cord is a two.component fishing line for a trimmer with a round cross section, inside which the core is located. It is this thread that is suitable for the majority of work. It must be remembered that the use of fishing fishing line, ordinary wire and other third.party materials as a cord pose a danger to others.

Removing and disassembling the coil

In order to correctly wind the fishing line for a trimmer to the coil of a trimmer for grass, you must familiarize yourself with the structure of the trimmer head. It consists of a protective casing, a bobbin with a thread, a hull cover, as well as a spring that is present only in some devices.

Starting to disassemble the coil, you must completely turn off/de.energize the device. In this case, the method of work directly depends on the type of head. The first option is to conduct the following actions:

  • The user presses on fixers located on both sides of the cover.
  • After removing the lid, the spool is extracted. Some models may have a spring, which also needs to be extracted.
  • A screw is located in the center of the case, which should be unscrewed with a regular screwdriver.
  • When the fasteners are removed, it remains to remove the gearbox from the shaft, gently shaking the case of the product body.
correct, trimmer, fishing, line

The second option for removing the coil for refueling the fishing line in a trimmer for grass is to tighten the head for the gearbox shaft. To carry out such a procedure, many devices are equipped with a hole into which you can insert the tool. When the screwdriver is inserted, the user can only take up the product body and scroll it clockwise. It is noteworthy that this method, in contrast to the previously described method, differs in the simplicity of execution.

The choice of fishing line

In order for the dressing of the fishing line to the trimmer head to be successful, it is important not to fail to choose the consumer material. The thicker the cord you refuel, the more thick and hard grass it can cut. A universal fishing line for a trimmer is often used, the diameter of which is 2 mm. You can choose the diameter suitable for the mower in the following ways:

  • See the information about the thickness of the fishing line in the instructions attached to the trimmer.
  • Pay attention to the squash itself. Sometimes information is applied on it about possible fishing line diameters.
  • Another option is to try to insert the cord into the output. If it easily passes into it, then the selected fishing diameter is suitable for use.

You can choose a cord thread by type of engine. If the fishing line for the trimmer is too thick, then the resistance to rotation will increase. the engine in this case will overheat and will soon fail. Useful recommendations:

  • For an electric device with an engine of less than 500 in, a thread of 1.3 mm thick is suitable. If this was not found, then you can use a fishing line for a trimmer by 1.6 mm. If the power is more than 1 kW, then select a cord with a diameter of 2 mm.
  • The gasoline trimmer for grass has a shaft mower. For the bent version, the cord for 2 mm is often used. If the shaft is straight, then set the thread 2.4–2.5 or 3 mm. The thickest fishing line for a trimmer is installed on powerful devices. from 1.3 kW.

Pay attention to the type of cross section of the cordry thread. Some popular options:

  • The most common fishing lines with a round section. They mow fresh herbs well, but they cope worse with shrubs, drows.
  • Twisted (spiral) cord does not differ in high strength, but well suitable for thin young grass.
  • The jagged thread with sharp edges is ideal for a large weeds in a neglected area.
  • You can mow the lawn in a rectangular, starry or square fishing line for a trimmer for grass, but they are not very durable.
  • The most durable is a two.component cord with an internal core and a round section.
correct, trimmer, fishing, line

Keep in mind that it is impossible to use wire, metal strings and cables, as well as an ordinary fishing thread. The device will be dangerous for both the user and for others. So the cable or similar products will gradually begin to shut down, as a result, their ends will be reacted, and small pieces will scatter at high speed.

Removing and disassembling the coil

The braid trimmer head consists of a casing, a spring (not in every model), bobbins with a cord, cover. Before proceeding to disassemble the coil of the electric unit, be sure to turn off the trimmer for the grass from the network. The disassembly method depends on the mounting of the mowing head. First option:

  • To remove the lid covering the inside of the head, click on the latches (latches), which are located on its two sides.
  • Remove the lid under which you will see the spool. remove it from the body. Some trimmers have a spring under the bobbin coils, which should also be carefully pulled out.
  • Removing the bobbin, you will see the screw in the center of the case. Unscrew it with a screwdriver.
  • After extracting the fasteners, take the case body and, shaking it in different directions, remove the gearbox from the shaft.

In the second version, the head of the trimmer for the grass is twisted onto the shaft of the gearbox. To remove it, you need to fix the shaft. To do this, in such devices there is a hole through which a thin screwdriver or metal rod is inserted. Brief Instruction:

  • Insert a screwdriver into a special hole, then stall the shaft.
  • Get the body of the head and start twist it. This should be done clockwise, t. to. Larva shaft thread.

How to change a fishing line for a trimmer on a lawn mower: detailed instructions

In 1971, American entrepreneur George Bollas invented a mower for grass, where a fishing line for a trimmer played the role of a cutting knife. A lot of time has passed since then, the drive has become more powerful, a modern trimmer can easily damage the bark, so that the idea itself was transformed into mowing around obstacles without damage to the very cutting apparatus of a mowing room. For a neat mowing around obstacles, you can have a head with a smaller fishing line, it is easy to change it when moving from mowing large areas to delicate blocking. However, periodically and the cutting tool itself requires replacement. We tell you how to disassemble the head of the lawn mower (trimmer for grass) and wind a new fishing line for a trimmer.

All about the replacement of fishing line with a trimmer head

There are many types of heads that are designed for different types of fishing line. The latter is also available in several diameters: from 1.0 mm to 3.2 mm. At the same time, its section is round (including with a special groove to reduce noise), square, twisted and in the shape of a star.

There are no clear preferences, and this explains the wide variety of forms and diameters in the market. The round shape is usually stronger, but has a worst cutting ability, in addition, when rotation, it makes a characteristic sound. Therefore, sometimes they make an acoustic groove, however, the use of this fishing line makes sense only on battery trimmers, in machines with gasoline and network drive, the sound level of the drive itself practically drowses the sound from the fishing line. The square has a good cutting ability, and despite the fact that such a fishing line for a trimmer is less durable than round, on average it is consumed less. A square fishing line for a trimmer quite easily cuts the shoots of the same Ivnyak up to 1 cm in diameter. The star has the maximum number of cutting faces, mows best and is the fastest consumed.

The next nuance when choosing is stiffness. The fact is that in the production of nylon, a modifier (often maleine anhydride) is added to it, which improves its strength and prevents gaps. However, modifiers are not the cheapest component, they are trying to save on it. Therefore, it seems to be a good fishing line for a trimmer that remained for the winter, in the spring suddenly behaves completely differently. it breaks, stops doing normally from the reel. There is a recommendation to soak a fishing line for a trimmer in the water before work, but I do not see much sense in this, malein anhydride interacts with water, but if it is not enough in the nylon, then there will be nothing to interact. Therefore, it makes no sense to stock up on fishing line for a long period of time, a breakdown or constantly torn fishing line for a trimmer, which also does not want to leave the reel itself, can significantly complicate the work.