How to correctly tuck the line for the trimmer on the grass trimmer

How to wind a trimmer line on a grass trimmer

Cord thickness should be in line with the parameters of the chosen tool. Too thick trimmer fishing line will tangle the thread on the reel, contribute to motor overheating and rapid wear on the bushings.

According to the thickness of the line for the trimmer is conditionally divided into several types:

  • Within 1.2 to 1.6 millimeters. Suitable for models with power up to 0.5 kW. Often these are electric mowers;
  • 2 mm to 2.4 mm. This size is the most popular because it can handle young and stubborn grass. Installed on tools with a capacity of about 1 kW;
  • 3mm to 3.2mm. Suitable for gasoline-powered units that will mow thick stems of weeds;
  • 4mm cord. Handles overgrown areas.

To determine what kind of line for the trimmer is suitable for the scythe, you can use one of the ways:

  • The thickness of the court should be specified in the owner’s manual;
  • Manufacturers often put important data on the bobbin, including the allowable diameter;
  • Slide the trimmer line into the outlet hole. It should pass through seamlessly.

The shape of the section is also paid attention to, because the thread does not cut, but interrupts the grass stem. Types of cords according to the shape of the section:

  • Round. The all-purpose version that cuts both fresh and dry cut vegetation;
  • Multifaceted with 3 to 6 facets. You can mow stiff and thick stems. But the consumption of this material is quite high, so it is only suitable for specific purposes;
  • Shaped. Star-shaped or square with notches. The first is used to cut fresh vegetation.

Grass trimmer fishing line is made of different materials:

  • Nylon line made of polyamide or polypropylene is best suited for brushcutters. Inexpensive polyethylene versions. They are not resistant to stress and do not withstand frequent temperature fluctuations. Polypropylene line for a trimmer will last longer if you soak it in water for half an hour beforehand;
  • The strongest are considered strings with aluminum particles and a diameter of about 4 millimeters.

Do not use metal wire or rope, which can damage the tool.

On the basis of the described parameters, you can choose the optimal line for the trimmer for the care of lawns.

How to wind a line for a trimmer on a brushcutter reel: method one

Before you start winding, you need to open the trimmer head.

First, determine the amount of line, which will be spooled on the bobbin. The coil must not protrude over the rims, otherwise the spool will not fit into the casing.

After determining the length of the line, you can start threading it into the bobbin:

the line for the trimmer is folded in half, with one edge left 10-15 centimeters longer. The bobbin is divided into two parts by a central rim. It has a groove for the court, which must be bent in half

Tightening will be needed for threading; The winding direction is important. The bobbin must have an arrow or inscription indicating the winding side

If there is no indicator, there should be an arrow on the mower head. The cord should be wound to the opposite side; The line for the trimmer should be wound as carefully as possible, the thread should be as taut as possible; After finishing the laying, the short end of the thread should be secured by inserting it into the appropriate diameter groove on the side of the spool. The long edge is fastened on the opposite side; At the fixed line should be cut edges with a gap of about 10 centimeters; tucked spool is installed in the mowing head. The edges of the thread are pulled up from the fixing grooves; The cover is put on and secured with the latches. It must be fully engaged.

How to tuck a trimmer line into the grass trimmer spool: the second way

Some reels can be tucked in another way. Two lengths of thread are wound, not one folded in half.

  • As in the first case, the length of the new thread is determined;
  • One edge of the bobbin is bent with a hook;
  • At the bottom of the bobbin there are holes for fixing the fishing line, where the bent edge of the thread is inserted;
  • The thread is wound behind the arrow on the spool. The level of winding should not exceed the diameter of the spool;
  • The same is done with the second cell of the bobbin;
  • The edges of the fishing line that stick out of the holes need to be trimmed. You can simply turn on the scythe, the knife will cut them while spinning. The line for the trimmer is cut by hand with scissors if the diameter of the court is too large.

Features of the trimmer application

Such a convenient, and most importantly, effective device as a grass trimmer, there are several variations:

As is clear from the names, the types of grass trimmers differ markedly from one another. But regardless of the type of this tool, its cutting element can be a line for a trimmer. Of course, the line tucked into the grass trimmer reel for trimmer is not endless. And sooner or later it will need to be replaced with a new one.

Consumption of fishing line directly depends on how often you use the device and the amount of work performed. The more grass you cut and the more often it is trimmed with the grass trimmer, the more the trimmer line is consumed. And consequently, the faster it will run out. This raises the question: How to tuck the trimmer line into the grass trimmer reel?

Not everyone knows the answer to this question. But the coiling of fishing line on the reel plays an important role in the work of the grass trimmer

For the device to function properly, it is very important to properly wind a new line for the trimmer on the spool. On how to change the line for the trimmer on the trimmer, and we will talk in this article

Choosing a fishing line

In order to successfully tuck the fishing line into the trimmer head, it is important not to miscalculate with the choice of consumable material. The thicker you feed the cord, the thicker and harder the grass it can cut. Often a universal line for trimmer, which has a diameter of 2 mm, is used. You can find the right diameter for your mower in the following ways:

  • Check the manual provided with your trimmer for information on line thickness.
  • Note the bobbin itself. Sometimes it is labeled with information about the possible line diameters.
  • Another option is to try to insert the cord into the outlet hole. If it will fit through it without difficulty, then the chosen diameter of the line is suitable for use.

Grass trimmer reel specifications

Reel for grass trimmer Choose a cord by the type of engine. If the line for the trimmer is too thick, the rotational resistance will increase. the motor will then overheat and will soon fail. Helpful tips:

  • For an electric device with an engine less than 500 V, a 1.3 mm thick filament is suitable. If you don’t have one, you can use a 1.6 mm line for your trimmer. If more than 1 kW, select a 2 mm cord.
  • The gasoline grass trimmer has the importance of the shaft mower. For the bent version is often used cord at 2 mm. If the shaft is straight, use 2.4 to 2.5 or 3 mm filament. The thickest line for the trimmer is installed on powerful devices. from 1.3 kW.

Pay attention to the type of cord cross-section. Some popular options:

  • The most common lines with a round section. They mow fresh grass well, but cope less well with shrubs, deadwood.
  • Twisted (spiral) cord is not highly durable, but not bad for thin young grass.
  • Serrated filament with sharp edges is ideal for large weeds in a neglected area.
  • You can mow the lawn more evenly with a rectangular, star or square grass trimmer line, but they are not very strong.
  • The strongest is a two-piece cord with an inner core and a round section.

Types of line for grass trimmer Note that you can’t use wire, metal strings and ropes, as well as ordinary fishing line instead of fishing line. The device will be dangerous for both the user and those around them. So the rope or similar products will gradually start to work, resulting in their ends unraveling, and the small pieces will fly apart at high speed.

How to wind a trimmer line onto a Patriot grass trimmer reel?

Almost every beginner faces the problem of changing the fishing line when using a grass trimmer. Despite the fact that changing the line for the trimmer is very easy, you need to learn how to do it correctly. Changing a fishing line with the proper skill will not take more than five minutes. you just need to practice it all the time. This article will look at replacing the filament using Patriot trimmers as an example.

Removing and disassembling the coil

In order to properly wind the line for the trimmer on the grass trimmer spool, it is necessary to become familiar with the structure of the trimmer head. It consists of a protective cover, a bobbin with thread, a housing cover, and a spring, which is present only in some devices.

Before proceeding to disassemble the spool, it is necessary to completely turn off / de-energize the device. The method of operation depends on the type of head. The first option is to carry out the following actions:

  • The user presses the latches on both sides of the cover.
  • After removing the cover, remove the bobbin. Some models may contain a spring, which must also be removed.
  • In the center of the housing there is a screw that must be unscrewed with an ordinary screwdriver.
  • When the fasteners are removed, it remains to remove the gearbox from the shaft, gently rocking the body of the product.

The second option for removing the spool for threading the line in the grass trimmer is to screw the head onto the gearshaft. For this procedure, many devices are equipped with a hole into which you can insert a tool. When the screwdriver is inserted, the user only has to take hold of the body of the product and twist it clockwise. It is noteworthy that this method, in contrast to the previously described method, is notable for its simplicity.

Winding the fishing line

It is not difficult to insert a fishing line into the grass trimmer. To carry out this operation, it is necessary to follow a simple algorithm of actions. The first step will be to determine how much consumable material is enough. To make its calculations, it is necessary to wind the line for the trimmer on the bobbin so that the resulting coil would be less than or equal to the diameter of the sides of the structure.

When you have decided on the size of the cord, you need to fold it so that one part of it was longer than the other by 15 cm. Winding the cord begins at the edge that divides the bobbin into 2 parts. Here will be located the fastener, in which you need to insert the thread, bent in half.

Now you need to figure out which direction to tuck the trimmer line into the grass trimmer. To do this, you need to examine the bobbin. there is often a special arrow on the bobbin. If there is no explanatory information, you should find the pointer on the trimmer head, and start winding in the opposite direction. The further steps can be divided into 4 steps:

  • Finishing winding the cord. To do this, it is inserted into the side groove on the reel. The second end of it is attached to the opposite slot.
  • The ends of the fixed line are cut off. Leaves an allowance of 7-10 cm.
  • The tucked part is placed in the head of the grass trimmer. To do this, the thread is inserted and pulled up alternately in the inlet holes of the structure.
  • The filament is pulled out of the grooves. Once the action is complete, the product cover is secured with clamps.

Once the last step is complete, the garden tool is ready for use. If after inserting the fishing line into the grass trimmer the device does not work properly, it is recommended to repeat the procedure, changing the thickness or type of cord. Otherwise, the product may fail.

How to remove the reel from a grass trimmer and retrieve the line for the trimmer

Initially, before you tuck the line for the trimmer into the grass trimmer reel, it is necessary to remove it from there. A reel or tip is a device that sits inside a mowing head, reel or reel. There are different types of heads (depending on the manufacturers), but the principle of replacing the line on the spool is the same in all. The first thing to understand is how to remove the head from the tool, as well as how to get the reel with the fishing line out of it.

This is interesting! You can replace the fishing line directly on the tool, but if you are doing it for the first time, it is still recommended to remove the head, and study the detailed process of winding. Once you have mastered the technology, you can do the replacement work on the trimmer trimmer or gasoline mower.

The instruction on how to unscrew the manual head on the trimmer is as follows:

  • Turn the tool upside down and, if necessary, clean it. Grasp the two finger grips on the cover locks (on the mowing head) on one hand, which are symmetrically positioned. After lightly pressing them inside, remove the protective cover from the drum
  • Then remove the filament spool from the reel shaft. The hedge trimmer has no fasteners on the shaft, so you can disassemble it with one hand
  • The main part of the drum is fixed with a screw, which must be unscrewed with a screwdriver with an appropriate tip or bit
  • To unscrew it, hold the base of the drum with one hand and turn it counter-clockwise with the other
  • After that you can proceed to dismantling. To do this, do not pull it with all your might, but gently wiggle it sideways to slowly disengage it from the metal shaft on which the drum is seated
  • When reassembling, place the head in the slots of the square shaped screw

This process is not difficult and as you understand, there is no need to dismantle the entire head if you know how to replace. Consider these nuances when disassembling:

  • It is advisable to periodically remove the head to prevent corrosion of the threaded joint. If you never unscrew it, it may be difficult or even impossible to do so if you have to
  • If a screw has a square drive head then a screwdriver or bit of the proper size should be selected for unscrewing to avoid slipping on the head
  • When reassembling the unit, treat the threaded seating with a lubricant, such as solidol or machine oil
  • If the edges on the screw have slipped off, you can use special clamping pliers to unscrew it
  • There are reels that do not require prior disassembly. To disassemble them, you should take hold of it, and rotate it in the opposite direction of the clockwise direction

Knowing how to disassemble the drum, you should go on to figure out the process of replacing the grass trimmer’s fishing line. The video below shows a detailed process on how to open the grass trimmer reel and disassemble it.

Block: 3/8 | Number of characters: 2920

Choosing a line

In order for the threading of the line into the trimmer head to be successful, it is important not to miscalculate with the choice of consumable material. The thicker you thread the cord, the thicker and tougher the grass it can cut. Often a universal trimmer line with a diameter of 2 mm is used. You can find the right diameter for your mower in the following ways:

  • Check the instruction manual supplied with your trimmer for information about line thickness.
  • Pay attention to the bobbin itself. Sometimes information about possible line diameters is printed on it.
  • Another option is to try inserting a cord into the outlet hole. If it will fit through without difficulty, then the chosen cord diameter is suitable for use.

Reel for grass trimmer

You can choose the cord according to the type of motor. If the line for the trimmer will be too thick, then the resistance to rotation will increase. the engine in this case will overheat greatly and will soon fail. Helpful Recommendations:

  • For an electrical device with a motor less than 500 V, a 1.3 mm thick cord will do. If you don’t have one, you can use a 1.6mm line for your trimmer. If the power is more than 1 kW, then choose a cord with a diameter of 2 mm.
  • The gasoline grass trimmer has a shaft mower. For the bent version, a 2 mm cord is often used. If the shaft is straight, install 2.4-2.5 or 3 mm thread. The thickest line for the trimmer is installed on powerful devices. from 1.3 kW.

Pay attention to the type of cross-section of the cord as well. Some popular options:

  • The most common lines with a round section. They cut fresh grass well, but are less efficient at cutting shrubs and dead wood.
  • Twisted (spiral) cord is not very strong, but not bad for thin young grass.
  • Serrated filament with sharp edges is ideal for large weeds in a neglected area.
  • Rectangular, star-shaped or square grass trimmer lines mow the lawn more evenly, but they are not very durable.
  • The strongest cord is two-part cord with an inner core and a circular cross-section.

Types of fishing line for grass trimmer

Note that wire, metal strings and ropes, as well as ordinary fishing line cannot be used instead of fishing line. The device will be dangerous for both the user and others. So the cord or similar products will gradually start to work, as a result their ends will unravel, and the small pieces will fly away with great speed.

Block: 3/6 | Number of characters: 2323

Choosing a line

In order to successfully thread a line into the trimmer head, it is important not to miscalculate with the choice of consumable material. The thicker the cord you tuck in, the thicker and tougher the grass it can cut. A universal trimmer line with a diameter of 2 mm is often used. You can find the right diameter for your mower in the following ways:

  • Check the manual that came with your trimmer for information about line thickness.
  • Note the bobbin itself. Sometimes it has information on the possible line diameters.
  • Another option is to try and insert a cord in the outlet. If it passes through it without difficulty, then the chosen line diameter is suitable for use.

Grass trimmer reel

Choose a cord you can according to the type of engine. If the line for the trimmer is too thick, then the resistance to rotation will increase. the motor in this case will overheat greatly and will soon fail. Helpful hints:

  • For an electrical device with a motor less than 500 V, a 1.3 mm thick filament is fine. If you could not find one, you can use a line for the trimmer for 1.6 mm. If the power is more than 1 kW, then choose a cord with a diameter of 2 mm.
  • At the gasoline trimmer for grass matters the shaft mower. For the bent version is often used a cord of 2 mm. If the shaft is straight, use 2.4 to 2.5 or 3 mm filament. The thickest line for the trimmer is installed on powerful devices. from 1.3 kW.

Pay attention to the type of filament cross-section. Some popular options:

  • The most common lines with a circular cross section. They mow fresh grass well, but cope less well with shrubs, dead wood.
  • Twisted (spiral) cord is not very strong, but is good for thin, young grass.
  • A serrated, sharp-edged cord is ideal for overgrown weeds in a neglected area.
  • Rectangular, star-shaped or square grass trimmer line can mow the lawn more evenly, but they are not very durable.
  • The strongest. a two-piece cord with an inner core and a circular section.

Grass trimmer line types

Note that wire, metal cords and ropes, and ordinary fishing line should not be used in place of the fishing line. The device will be dangerous for the user and others. So the rope or similar products will gradually begin to work, causing their ends to unravel and the small pieces to fly apart at high speed.

Block: 3/6 | characters: 2323

How the line head works on the brushcutter. why the principle of operation

Depending on the manufacturer, machines are different not only externally but also internally. Most reels have a pressure spring inside (semi-automatic and automatic). Above is an instruction on how to disassemble the grass trimmer head without a spring, t.е. on a manual type head. The principle of dismantling a semi-automatic head with a spring inside is almost identical to the above instructions.

The principle of operation of the semi-automatic grass trimmer reel is as follows:

  • Inside the head is a spool, which is planted on slits that prevent it from moving freely
  • The coil is actuated by a spring which presses it against the slits in the cover structure
  • There is a trimmer line wound on the lead, the length of which depends on the tool itself. Usually this length is 1 to 4 meters
  • During the work, if it is necessary to increase the length of the line, the protruding part of the drum is pressed, by which it is disengaged from the slots. At the same time, the line for the trimmer is coiled from the drum, increasing in length
  • After releasing the desired amount of line, release the hold-down and continue mowing

The advantage of a tool with a fishing line is that this consumable does not require sharpening, compared with metal discs. over, if a stone or wood gets in the way, the line for the trimmer simply comes off, without negatively affecting the gearbox and engine of the tool, as it happens in the case of metal cutting discs.

Knowing the design and construction of the types of mowing or trimmer heads, it is necessary to proceed to consider the process of threading the fishing line into the grass trimmer spool. This is the point that most power tool owners have a hard time with.

Block: 4/8 | Number of characters: 1782

Advantages of a trimmer head

In addition to the heads on trimmers, metal discs are also used. Compared with them, cutting elements with a fishing line have a number of advantages:

  • no need to sharpen consumables
  • If stones or other hard objects hit the trimmer line will simply rip, not injure others or the mower
  • Thread breaks do not adversely affect the trimmer’s gears and motors.
  • The head machines remove grass better than their metal counterparts.

Tips

Working with such equipment, as grass trimmers, requires caution and attentiveness. Implementation of safety measures during work is mandatory for beginners and experienced masters. Confident lawn mowers sometimes lose their guard, make irreparable mistakes and get seriously injured. That’s why it’s important to keep an eye on your hands and feet when operating a barbed wire brush

  • Close the reel cover with all latches.
  • Do not wind more fishing line than it’s supposed to: it’s hard to unwind later.
  • After refilling the reel, always check the tool before mowing.
  • Choose a quality material that fits the particular trimmer.

No need to try to mow coarse grass with thick stems with a line. There are steel discs for this. Wear protective clothing only. Wear safety glasses and proper footwear.

Design of the grass trimmer spool

Mowing heads for trimmers come in different designs. both simple and complex. The picture below shows a semi-automatic trimmer head from a Husqvarna brushcutter (Husqvarna) disassembled.

This type of head is present in the package of the majority of gasoline mowers and electric trimmers, such as STIHL (STIHL), Patriot (Patriot), Champion (Champion), Bosch (Bosch), Huter (Huter) and others. The design of the mowing head is quite simple. It includes the following parts:

  • the base of the mowing head;
  • A button for semi-automatic cord feed;
  • The bobbin (spool), in which the line for the trimmer is tucked;
  • spring;
  • eyelets. through them the line for the trimmer goes out;
  • trimmer head cover;
  • trimmer line (cord).

There are also simpler trimmer heads, shown in the following photo.

All these attachments don’t let you change the line length in semiautomatic mode (after you press the button). If the cord breaks, you have to stop the mower and change it manually.

Preparing to replace

To make it clearer, the mowing head (bobbin) was removed from the brushcutter. To change the line do not need to remove it, everything is done in place. It does not take long.

Dismantle the grass trimmer bobbin. it is held on the latches-catch. The cover is removed by pushing on the latches. If the hands do not have enough force to do it, then use a screwdriver.

The bobbin is made up of the following:

The principle is as follows. Pressing the button, the bobbin presses on a spring and comes out of the fixing grooves in the cover of the bobbin. Holding it in this state, you can twist the spool, thereby adjusting the length of the line. When you release the button, the body spring returns the coil to its original locked position.

Cutter block attachment

The cutting block is the main component of your Philips Styler. It has short, sharp edges and is used for fast, precise hair length trimming.

To remove the cutting unit from the styler body, check for the release button on the styler body. If it is present, press the button to remove the cutting unit.

If the styler does not have a release button, place your finger under the teeth of the cutter block and pull it out of the appliance. To reinstall, insert the lower part of the cutting unit into the styler body, then slide the part with the teeth in until it clicks. Do not use excessive force; this could damage the appliance.

If you are unable to install the cutting unit, check for foreign bodies in the body of the trimmer and try cleaning it with a small brush or cotton swab.

No matter how well the electric grass trimmer we have purchased works on the dacha plot or country house. Sooner or later the time will come when we need to remove the grass trimmer head for replacement or prevention. It is not necessary to remove the entire trimmer head in order to replace the fishing line. Within this article, I will tell you how to remove or replace the entire mowing head using the example of the BlackDecker GL716 electric grass trimmer.

Tips and recommendations on how to wind the line for your trimmer and what you need to know

There are some useful tips and recommendations that will be useful to know not only for beginners, but also for the experienced masters of trimmers. These tips will help prevent negative consequences in the form of injuries and malfunctioning of the mechanism. These recommendations are as follows:

  • Insert the cover until it clicks into place. This is 2 or more clicks depending on the number of clips. If one latch does not snap, the reel can jump out and injure a person when starting the tool
  • Do not wind the line for the trimmer with a strong pull on it, or in an amount greater than can be inserted in place. It is better not to wind up the tool, than to have more of it, as this will lead to negative consequences in the form of inability to unwind it if necessary
  • If you own the tool not with two line outputs, but with one (usually these are low-powered units), then the winding process is performed in a similar sequence as described above, only with the difference in the absence of the middle rim between the extreme bases of the spool
  • After changing the material, you should first check the functionality of the tool, and then proceed to mow the grass. If not checked beforehand, the line may unravel and injure someone

This is interesting!Choose proper quality material to avoid injury when working with petrol and lawn mowers, trimmers and brushcutters. When mowing grass, small stones and other materials fall under the rotating parts, which can fly long distances. Therefore, despite the fact that a line for a trimmer is not a knife, work with the tool should be carried out in special protective outfit. The result of the work done is the following: after the new material has been replaced, the ordinary material is enough for up to 600 square meters, but taking into account the reinforcing layer on the line. Conventional nylon materials last less, which is important to consider when working. Do not try to mow thick-stemmed grass with a fishing line, as there are special metal discs or knives for this purpose.