How to cut a 45 degree angle on a baseboard

Inner corner

First of all, it is necessary to consider the technique of how to cut the inner corner of the ceiling plinth. After all, in any room they are. If there are no external corners in ordinary rectangular rooms, then these varieties will have to be cut in any case..

degree, angle, baseboard

A plinth is placed on the bottom of the miter box with the side that will adjoin the ceiling. The bottom of the fillet will be pressed against the wall of the tray.

If the material is hard, it is cut with a metal saw. Soft items can be easily handled with a sharp knife. In this case, the angle should be equal to 45 degrees. If the pressure during cutting is too strong, hooks and chips will form on the plinth. An adjacent corner is cut in the same way..

Before gluing, they are applied to the wall and, if necessary, small irregularities are corrected. There should be no gaps between the skirting boards. If this is the first time this work is done, you can practice on small pieces..

How to cut and install wall baseboard trim 45° cuts

Homemade tool

Don’t you have a miter box? No problem! You can do it yourself. When pruning for the first time, it is best to apply it in your work. This will require a plywood board, paper or cardboard..

Interested in how to cut the outer corner of the ceiling plinth, as well as its internal varieties, you need to take this approach into service. Draw two parallel mowing lines on the selected material. Next, using a protractor, angles of 45 degrees are made around the edges..

A homemade tool is applied to the plinth, making the appropriate notes. The pruning technique is the same. The miter box is not used if the walls in the room are very uneven. When creating an angle of 45 degrees, gaps between the joints are obtained due to such inconsistencies. Therefore, pruning is done in the previous way. Before editing, the edges must be corrected.

How to cut corners on skirting boards? Step-by-step instructions, practical tips and advice

Repair is a responsible and costly undertaking. Although you can save a lot if you carry out the work yourself. Cosmetic finishing of the premises is carried out according to certain technologies. You can decorate the interior using a variety of materials..

Today, a very popular technique is the use of skirting boards to hide irregularities between the walls and the ceiling. In order for the contour to be aesthetic, it is necessary to do the work carefully. How to cut corners on skirting boards will help you understand the advice of experienced construction and repair masters. They will tell you how, using various tools, to perform the necessary manipulations with decorative finishes of various types..

Outside corner

Quite often, the contour of the walls in a room has a complex shape. In this case, you will need to figure out how to cut the outer corner of the ceiling plinth. To do this, it is laid on the bottom of the miter box in the same way as in the previous version, with the side that adjoins the ceiling.

Other slots are used for these corners. They also have a slope of 45 degrees, but are on the other side. Further, after marking and trimming, 2 plinths are applied to the corresponding place on the ceiling. Adjustment in progress.

Difficulties can arise when it is necessary to cut the same skirting board on one side for the outer corner, and on the other for the inner one. Many people make a mistake here. First you need to cut the inner corner. Otherwise, a skirting board that is too shortened will not dock in any place..

Preparatory work

To make the process quick and easy, use a tool such as a miter box. This is a U-shaped template. There are slot patterns in its side walls. They have a different angle of inclination..

There is another technique that allows you to evenly glue the ceiling plinth. Cutting corners without a miter box is possible. But still, the use of such a tool greatly facilitates the work..

First you need to mark the skirting board. If you want to create an outer corner, measure the length along the ceiling, and the inner one along the wall. For the fillet, a slope of the mowing line of 45 and 90 degrees is used. Since this is a fairly small number of slot options, it is quite possible to make a template yourself. This requires only a sheet of paper or cardboard..

If the repairer has considerable experience in carrying out such operations, he can cut corners without additional tools. The craftsman applies the fillet to the wall, and then marks the product right here. After that, he cuts off the excess. An inexperienced craftsman, most likely, will not be able to cut even corners the first time. Therefore, it is better to use a miter box or close irregularities with decorative corners..

General characteristics of finishing

Studying the question of how to properly cut a corner on the ceiling plinth, you should familiarize yourself with the features of such a finish. The stucco molding between the ceiling and walls is now made of artificial materials. It can be polyvinyl chloride, expanded polystyrene or polyurethane. Wood can be used from natural materials.

In the construction business, the ceiling plinth is called (scientifically) a fillet. Of all the materials from which such finishing elements are made, polyurethane is considered the highest quality. Therefore, it is better to choose it. Next, let’s try to figure out how to cut the corner of the ceiling plinth. Expert advice will help you do this job well.

Skirting board material

Experts agree that polyurethane is the best material for the presented finishing products. But even he has a number of disadvantages. These should be taken into account before cutting corners on the skirting boards. Polyurethane is susceptible to temperature changes. Therefore, it is not used for decoration in the kitchen or bath. Otherwise, the skirting boards will quickly crack and lose their aesthetics..

Expanded polystyrene has almost all the positive characteristics inherent in polyurethane. But it is still more fragile material. It’s easy to break.

PVC skirting boards are relatively cheap. But it is very easy to leave dents or gouges on them. Therefore, work with such products should be very careful..

Wood looks very nice, but not in all interiors. In addition, it is rather difficult for a non-professional craftsman to work with such material. Do you want to make repairs with your own hands? Then you’d better still choose polyurethane or expanded polystyrene..

Work without a miter box

The polyurethane skirting board looks very nice in the interior. How to cut corners on such a product so as not to spoil its appearance? And here an inexperienced master will be helped by expert advice. Not always a home craftsman has at hand such a tool as a miter box. You can do without it.

For this, the markings are performed directly on the wall. First, the required length of the decorative item is measured. It is cut at right angles. Next, each detail is applied to the ceiling. Their contour is outlined with a pencil. This produces an intersection. It is applied to both skirting boards.

An inclined line is drawn from the point of intersection to the edge. This is the clipping boundary. Correct it before gluing by attaching both skirting boards to the corner. This is a fairly simple method, but even it requires a good eye and accuracy in work..

Which skirting board is better?

Before you cut the corners correctly on the ceiling plinth, you need to choose the right one..

Tip: the ceiling plinth will look harmonious if its width is selected correctly. The higher the walls, the wider the skirting board should be.

The most durable, moisture resistant and elastic are polyurethane fillets and cutting a corner from such a ceiling plinth is not very easy. However, all these positive qualities are “covered” by one significant drawback – they do not withstand sudden changes in temperature, which does not allow them to be used in all rooms..

For example, in a kitchen with a gas or electric stove, polyurethane fillets will retain their original appearance for about a week. After that, with frequent cooking, when hot air rises to the ceiling, then falls, they will begin to deform, spoiling the whole “picture”.

Skirting boards made from other materials also have their drawbacks.

For example, products made of polyvinyl chloride have increased electrostaticity and if dents appear on their surface during operation, it will be impossible to remove them. At the slightest mechanical impact, ceiling skirting boards made of expanded polystyrene and polystyrene break.

If we talk about which ceiling plinth for stretch ceilings or ordinary ceilings is better, then it probably won’t be possible to give an exact answer here. Since each of them has its own positive and negative qualities. Therefore, you still have to make a choice, starting from the financial resources that you have, and on the conditions under which the fillet will be operated.

How to cut a ceiling plinth in the corners without a miter box the first time

How to cut the corners of a ceiling plinth. Photo 1

Probably everyone who at least once carried out repair work with their own hands faced the problem of cutting out the outer and inner corners of the ceiling plinth. Ceiling skirting board, also called a fillet, is used in repairs to hide the uneven border between the wall and the ceiling and to give the interior completeness. How to cut a corner of a skirting board without a miter box? We will talk about this in our article..

How to cut a ceiling plinth in the corners without a miter box? If you don’t have a miter box on hand, it doesn’t matter. You can cut the outer and inner corner without a miter box.

Fillets on the market today are available in different sizes, shapes and colors, with or without relief patterns. The material from which they are made is also different. These are mainly: polyurethane, expanded polystyrene, polystyrene and polyvinyl chloride. But recently, the most popular in the repair work has become a wooden ceiling plinth. Its aesthetic appearance allows you to add elegance and rigor to the design of the room..

How to cut corners without a miter box?

At first glance, it seems that cutting off the corner of the ceiling plinth is not difficult – cut the edges of the plinths at an angle of 45 degrees and glued them. However, this is not at all the case. Each corner of the room can differ in its parameters, for example, one 90 degrees, the other 88 or 92.

This difference is the norm, especially in buildings over 30 years old. Therefore, if you simply cut the skirting board at an angle of 45 degrees and glue it on the border between the ceiling and the wall, a gap may form that should not be there. How to dock the ceiling plinth so that there are no gaps? So, let’s begin.

First you need to prepare a tool that will trim the edges of the skirting boards. This can be a metal saw or a regular sharp knife..

How to cut the inner corner of a skirting board without a miter box? The answer lies on the surface.

Take a skirting board and attach it to the corner in the same way as you will glue it. Using a pencil, draw a line along the baseboard on the ceiling. Remove the fillet.

We carry out the first step. Photo 2

Place the second skirting board on the other side of the corner where it meets the first. Follow the same procedure as with the first one. As a result, you should have the markup.

How to cut a ceiling plinth. Photo 3

Take the plinth, lean it tightly against the place to which you will glue, and transfer to it the point of contact of the two straight lines drawn earlier on the ceiling. From this point, draw the line to the opposite edge of the baseboard. This line will be the cut point..

We carry out the correct markup. Photo 4

Do the same for the second skirting board..

Here we cut off two skirting boards. Photo 5

Cut the edges of the skirting boards along the intended mowing line.

Attach the cut skirting boards to the corner. If the place of their joint has no gaps, you can start gluing the fillet. If there are gaps or irregularities, correct the cut corners with a knife.

How to cut the outer corner of a ceiling plinth? When creating an outer corner, the top should protrude above the bottom, the inner – the opposite is true..

Whatever ceiling you glue the plinth to, whether it is the ceiling in the bedroom or kitchen, do not rush, measure everything carefully. This will help you avoid spoiling the material..

What is it made of and what is it called

The very first skirting boards on the ceiling were made of plaster. They were cast in special molds and then installed on the ceiling with mortar. Such figured decorations were called fillets. Today you can rarely see them: they are expensive, and outwardly they are almost indistinguishable from the cheaper options. And the name is almost lost.

The most popular ceiling skirting boards are made of polyurethane or polystyrene. They are inexpensive, look great, easy to install, have a wide range of profiles and patterns. The width can be from 5 mm to 250 mm. They are used in almost any room, decorated in any style. An exception is wooden houses with a corresponding interior. Wooden products are most often used here – the style dictates its conditions.

There is also a similar plastic finish. It is mainly installed in bathrooms. But even in damp rooms, you can safely mount polyurethane strips – they are not afraid of damp.

You need to cut the ceiling plinth in the corners of any material in one of the ways described below. The only exception is plastic skirting boards: you can arrange such a corner only using ready-made corners.

How and how to cut

Working with skirting boards made from different materials means using different cutting tools. When working with a wooden skirting board, it is more convenient to work with a saw on wood. All others, including plastic, made of foam and other polymers, are better cut with a metal sheet. The result is a smoother cut, less burr. Saws are usually used when working with a miter box.

Corner design looks attractive

When working with polystyrene skirting boards without special devices, they are cut with a good office knife. Its blade is quite thin and even, the cut is smooth, not wrinkled. If you use a saw with polyurethane or polystyrene, do not press hard: you can wrinkle.

In general, in order to get used to the tool and material a little, take a piece and practice on it: cut, saw, trim. So there will be fewer problems when working.

Using a miter box

If the corners and walls in the room are even, you can use a special carpentry tool – a miter box. This is an inverted U-shaped chute in which the mowing line is marked for cutting at 90 ° and 45 °. The part in which you need to make a gash is laid inside, a saw is inserted into the guides. The part is held in place, cut at the desired angle.

This is what the miter box looks like. Can be plastic, wood or metal

In the case of skirting boards, not everything is so simple: they must simultaneously adjoin two surfaces, therefore they must be pressed against one or the other wall of the miter box. When working with ceilings, they are pressed in the side closest to you.

The sequence of actions when finishing the outer corner, you need to make a gash at an angle of 45 degrees. Place the miter box in front of you. Trying on how the plinth will be located, determining which part of it will be attached to the ceiling. In order not to get confused and cut off the ceiling plinth correctly, place the strip that will be located on the right on the right, the one on the left on the left.

How to cut a corner on a ceiling plinth: install it correctly in a miter box

Press the part that is on the ceiling to the bottom of the miter box. The other side is closer to you and raised. Lean it on the wall of the device so that it does not stagger when cutting. That is, the front part of the skirting board turns out to be turned away from you. Do the cutting direction as shown in the photo below. By folding the two cut pieces together, you get a protruding outer or outer corner.

How to make the outer corner of a skirting board using a chair

First put the sawn-off parts in place “dry”, without applying glue. If the geometry of the corner is not so perfect, you can tweak it a little with a knife. It is easier to cover small errors with a special putty..

The situation is very similar with the inner corner of the skirting board. First you try on which side will be on the ceiling, press this part to the bottom of the miter box, lean the second part on the wall closest to you and make cuts as shown in the photo below.

How to make an inner corner of a ceiling plinth using a miter box

And again, first try on without applying glue, if necessary, slightly adjust. Then apply a thin bead of glue to both surfaces that will adhere to the wall or ceiling..

Your own version of how to use the miter box correctly is shown in the video.

How to make a corner of a ceiling plinth without a miter box

Few people in apartments or houses have angles of exactly 90 °. Small deviations are easily corrected after fitting. But not always. Then you have to mark everything “in place” – under the ceiling.

You will need a finely contoured pencil (hard – it is not so visible on the ceiling, but leaves quite clear marks near), a small piece of plinth, a ruler and a good stationery knife if you work with polyurethane (polystyrene) baguettes or a metal saw for working with other materials.

Apply the plinth to the corner, draw along the outer edge with a pencil. Apply to the other side of the corner, also mark. You have a cross on the ceiling, the center of which marks the place where the plinths of the ceiling plinth should converge (look at the photo). Having installed a piece of plinth in the corner, which will be glued there and resting it with its end on the wall, transfer the mark to it.

How to make corners on skirting boards without using special tools

Now take a ruler and connect the edge of the skirting board with the marked mark. If you just put the plinth on the table and cut off along the mowing line, the two parts in the corner will still not fold: the inner part will interfere. It can be trimmed later by trying on the ceiling. The second way is to set the piece to be cut on the table with the piece that will be on the ceiling. And cut along the mowing line, but holding the knife at an angle of about 45 °. It will still be necessary to correct, but much less (and less chance of error).

Repeat the same operation with the second bar. Put it against the desired wall, rest the butt against the adjoining wall, mark the place where the cross is drawn, draw the line and then cut it off. Correction Carried out “dry” without applying glue.

You repeat exactly the same steps for the outer (protruding) corner. Now you know another way to make a corner of a ceiling plinth, and without a scissor or other special devices.

How to cut ceiling plinth in corners

The quality of the ceiling finish greatly affects the appearance of the room. Therefore, they try to do everything perfectly, or very close to it. The finishing touch to the design is the ceiling plinth. They give the finish a complete and holistic look. The strips themselves are mounted on flat surfaces simply: on special white glue, but problems arise with the design of the corners. Without knowing how to make the corner of the skirting board correctly, a lot of material deteriorates. How and what to cut it in the corners and tell you.

With decorative corners

There is one more, the easiest way. For skirting boards made of polyurethane or polystyrene, use ready-made, factory decorative corners. They are installed in a corner, strips are glued to them closely. Cutting them if necessary is very simple: a few millimeters with an ordinary clerical knife.

Examples of finished corners for fillets

How To Cut Baseboard Corners That Look Great

How to get the correct angle

Most of the problems when working with skirting boards arise in the design of corners. Since the surface of the products is complex, it will not be possible to simply cut off at the desired angle: it is also necessary to cut it so that they dock and, preferably, without large gaps. In reality, there are several ways to make the corner of a ceiling plinth perfect (or almost).

The ways

There are two most common methods for cutting flawless skirting corners correctly, easily and comfortably. The first implies the purchase of a special miter box with a large number of cuts along its perimeter, which help to cut the corner correctly and evenly. The second option is cutting corners without the help of a miter box, which we will talk about today. This process for beginners is quite complicated and painstaking, besides, the presence of a miter box does not guarantee 100% facilitation of this work, be prepared for the fact that the first time you may not succeed.

There are several ways to create corner joints without using a miter box..

One of them is the marking directly on the ceiling. To begin with, we need two pieces of baguette cut at a 90 degree angle. It is not necessary to take two-meter slats at once and try to cut them, you can cut off two pieces of 15-20 cm for easier holding with one hand in the position you need. Next, we apply them in the next order to the ceiling and draw a 5-centimeter line along the ceiling to the end of the baguette, pressing the plinth tightly. After that, we apply a second molding to the opposite corner, and do a similar action, and at the intersection of the baguette and the previously held mowing line, we make a neat pencil notch on the baguette. With the second plinth, you need to repeat the same thing, making a similar notch at the intersection of the baguette and the mowing line.

Now we can cut the baguette at the angle we need, for this, use a construction knife or a hacksaw, depending on the material from which the skirting boards are made (below we will tell you what materials the baguettes are made of and what is the best way to cut them). To cut the corner correctly, place the baseboard on the table or chair, and cut from the point you marked on the ceiling to the opposite corner of the baseboard. After that, you can easily join the corners and glue. It should be borne in mind that this method is suitable for fitting only the inner corners, it will not work to fit the outer corners..

The second method consists in tracing a sheet of paper or plywood under the miter box, for this you need to draw two parallel mowing lines, then draw a perpendicular from one mowing line to the other, so we get a marking for a right angle. To mark at 45 degrees, you need to use a clerical triangle or a protractor, passing two mowing lines through the perpendicular at 45 degrees relative to parallel lines. Further, as when working with a miter box, we put our plinth along the mowing line and cut at the required angle.

It should be borne in mind that this method does not guarantee you an ideal angle, and, in general, in our houses the corners are uneven – “filled up”, and therefore you will have to adjust the angle manually later.

The third method is to make a primitive miter box with your own hands, which is why it will not become less effective. To do this, take three planks or planks and knock them down in the shape of the letter “P”, make slots at right angles and two slots at 45 degrees. This way you cut corners without the “help” of the chair..

The fourth method is quite rare and inventive – it consists of tricks with thick paper or cardboard and a small bar. To do this, bend a sheet of cardboard at the angle you need, take a small block, which will serve as a template for cutting the corner. Press the prepared sheet of cardboard to it and, holding the knife or hacksaw strictly vertically, carefully cut the block at the angle you need. To trim the skirting board, simply place the piece on top of the skirting board, press firmly and cut along the mowing line of the piece..

The fifth way is the purchase of special fittings with ready-made ceiling corners: internal and external. Unfortunately, there are a lot of skirting board design variations; special inserts may not be found under your skirting board. But in general, it is very convenient for those who do not want to engage in cutting out corner joints..

But also if there are non-standard angles in your house, then ready-made blanks or a miter box will not help you. After all, there are only 45, 60 and 90 degrees you can cut the connection. In this case, cut the edge of the baguette by eye at an angle of 45 degrees, and when trying on to your corner, carefully trim it, so you will be able to achieve an almost perfect connection, with only one thing – there can be a lot of such fittings and trims.

As you can see, in the absence of a miter box, you can still cut the correct corner joint for baguettes, you just need patience and perseverance, and unnecessary skills will not interfere with anyone in the future..

Necessary materials

The set of tools for making a corner ceiling joint without using a miter box is not so great, and, in principle, does not differ from a set with a miter box. Almost every home has these tools:

  • pencil;
  • roulette;
  • ruler;
  • construction knife with replaceable blades;
  • hacksaw;
  • ceiling plinth.

You will need a tape measure and a ruler for accurate measurements and drawing straight lines, everyone has them in the house. It should be borne in mind that without a ruler, you will not be able to draw even mowing lines for cutting corners using the first method..

A construction or office knife with replaceable blades is an indispensable assistant in the house. Its cost, like a construction pencil, is low, and it is always available, it will give you the opportunity to cut off the necessary segments easily and evenly, cut out a corner or cut thin plates when adjusting the connection. Some skirting boards are made from a material that is recommended to be cut with a knife only, and not with a hacksaw due to the softness of the material.

You will only need a hacksaw if the material from which the baguettes are made is recommended to be cut only with it. A regular hacksaw with fine teeth will do..

A ceiling plinth must be chosen for both aesthetic and practical reasons. It should harmoniously fit into your design, cover the joints of the ceiling and walls, hide defects and irregularities. When choosing a baguette, it is necessary to take into account the material from which it is made – this affects the choice of cutting tools and glue for installation, as well as the type of coating on which the skirting board will be glued.

How to make a corner on a skirting board without a miter box?

  • The ways
  • Necessary materials
  • Step-by-step instruction
  • Recommendations

Step-by-step instruction

When installing a ceiling plinth, first of all, you need to prepare the surface before gluing the plinth, it must be cleaned of minor irregularities, then you need to prime the gluing points to create maximum adhesion between the glue and the wall or ceiling. The primer is the same as that used for wallpapering or ceiling tiles..

Before gluing, it is recommended to take a small piece of baguette and practice cutting corner joints so as not to spoil the excess.

So, you have everything ready, and it’s time to start the process of cutting out the corners. To create an inner corner, the first of the methods described above is perfect for you. If you have smooth walls, you can cut off equal pieces from the baguettes, and cut out the corner joints from them, then simply gluing the long strips neatly point-blank to them. These manipulations will facilitate your work when trimming and exclude the possibility of bending the baguette or breaking it..

If the walls have flaws, and you are worried that the gluing place will then be noticeable, you can adjust the corner on the floor, and then glue.

When cutting out the outer corner, it must be remembered that the inner corner rests against the wall, and the outer one, on the contrary, protrudes above it. Similar to the method described in the first method, you can try. The only difference will be that the skirting board should go beyond the wall to the width of your baguette plank. After trimming the planks to the desired angle and connecting them, you may need to manually correct the angle, since the angles in our homes are often not nearly 90 degrees. The rest of the methods described by us will allow you to more easily make the outer corner. Just like cutting an inner corner, it’s best to practice first – this will make your job easier and reduce skirting waste..

Before gluing the skirting boards, you need to make sure that the joints fit exactly. Modern assembly adhesives set very quickly, so you will have practically no time to correct the mistake, and tearing off the skirting board is both an opportunity to break it and the need to re-clean the surface of the skirting board and wall from glue. It is better to remove excess glue immediately with a small clean cloth or sponge so that there are no traces left..

With the right patience and the right fit, you can achieve a “seamless” joint and your molding will look solid, making it easier to paint and eliminate the need for a finishing putty to smooth joint seams..

Sometimes the unevenness of the walls or ceiling prevents you from gluing the plinth along its entire length, tightly pressed against the wall or ceiling, or you made a little mistake when cutting the inner corner, and you have a gap. To eliminate these defects, a white acrylic finishing putty is perfect. It can be painted well after drying, and with its help you can gently putty the joints. This putty is sold ready-made, you do not need to stir it yourself with water and worry about non-compliance with the proportions, depending on the manufacturer. If you want to make everything aesthetically pleasing, then spare the money and buy a small jar. According to personal observations, 0.5 kg cans of ready-made putty will be enough for you for all the flaws in the joints of the ceiling plinth, and for eliminating other minor errors during the repair.

And also for easier trimming of corners, you can use a clerical triangle, it will give you the ability to accurately cut a 45-degree angle.

One of the important factors to consider is the material from which the skirting board is made. Now they are made from PVC – polyvinyl chloride, expanded polystyrene (foam), wood and polyurethane. Depending on the material, glue and baguette trimmer should be selected.

For information on how to make a corner undercut in a ceiling plinth without a miter box, see the next video.

Fillet trimming procedure:

  • attach the fillet to the place of the planned installation and measure
  • the upper part of the plinth (the one that will be applied to the ceiling) lay on the bottom, the lower part of the plinth – press against the wall of the miter box
  • cut the plinth, smoothly and without sharp pressure, at an angle of 45 degrees. The trimming must be carried out with a hacksaw with a fine tooth (optimally – a hacksaw for metal) or with a knife. A large tooth will bite into material, especially foam with its porous structure – the butt will be uneven and chipped
  • the operation is carried out in the same way with the adjacent plinth – only the cut is made in another slot at 45 degrees
  • attach the obtained skirting boards to the place of planned gluing and select the optimal joining angle. If necessary, trim planes can be adjusted with a sharp knife to achieve the most accurate fit.

Advice! If it becomes necessary, on one fillet, simultaneously cut off the outer corner on one side and the inner corner on the other, the more complex element is cut first – the inner corner.

To trim adjacent fillets for inner and outer corners:

Trimming adjacent fillets

Advice! The most accurate cut can be obtained by cutting two skirting boards simultaneously. Since in relation to each other the skirting boards are sawn in a mirror image, both skirting boards can be folded with the inner sides to each other and tightly fastened in the miter box, after which just make one cut at an angle of 45 degrees.

Smooth and neat skirting corner in the kitchen

The corners of the skirting boards are decorated with a miter box

You can trim the baguette using a miter box

Ceiling plinth: how to make the corner of the joint correctly?

First of all, the solution to the problem – how to properly cut the corners of the ceiling plinth with your own hands – can be avoided simply by purchasing special fittings – a corner element. Today, you can pick up corner elements for any type of connection – both external and internal – simply insert the ends of the extreme fillets (plinth strips) into the corner.

This is the simplest option, which, on the one hand, provides a high-quality corner connection, on the other hand, it does not require serious skills and allows installation to be carried out without wasting time..

Ceiling plinth – decorative decoration of the room

White ceiling molding against white walls and ceiling

The plinth runs just below the mowing line of the ceiling along the border of the wallpaper

However, it is not always possible to choose a corner element that would stylistically match the existing skirting boards. In this case, you will have to cut the edges of the skirting boards yourself at a certain angle, which will ensure an even and tight fit of the fillets to each other..

In this case, cutting can be done in two ways:

  • using a miter box – a special template tool
  • manually – after performing the markup according to a certain method

Cutting corners using markup

If there is no miter box, then this is not a reason to give up, there is a method that allows you to get a good result, you just need to be careful and accurate. First of all, it is required to cut off those sides where the skirting boards will be joined, strictly at 90 degrees.

After that, we take the plinth and attach it to the wall as it is planned to mount it. Pay attention – the precisely cut end is firmly pressed against the wall. Now draw the line with a pencil:

We draw the line on which the plinth will be glued

We take the second plinth and repeat all the operations exactly, but on the other hand:

Marking the skirting board on the other side

We get the intersection point of the two lines along the ceiling – this will be the place where the skirting boards will join. Now let’s mark this point on each of the fillets:

Transferring the point of intersection of lines to the skirting board

the line that will run from the transferred point of intersection to the opposite edge of the plinth is the desired trimming line. With a sharp knife (with a metal file), clearly, but without strong pressure, we make a cut. We join the skirting boards in the corner, choosing the optimal position, if necessary, trim the corners with a knife:

Angle obtained by marking method

If the angle is not straight, the job becomes more difficult, but not much. We just measure its value exactly, divide it in half and get the value required in order to mark the cut of the plinth. For example, if the angle is 76 degrees, we need to cut at 38 degrees. In this case, it is better to make the initial cut at an angle of 40 degrees, and then at the joining point, adjust the angle with a knife.

Unfortunately, even with the most accurate and scrupulous work, it may turn out that the angle turned out to be not quite even and accurate – maybe not quite a flat wall, the angle is not quite straight, perhaps, when cutting, the material could deform somewhat under pressure. Therefore, the corner may have gaps along the mowing line of the docking, or dents appear on the edges – it looks sloppy and unaesthetic.

Advice! This can be corrected by using a sealant – just fill in the dents and crevices, let the sealant dry well and cut off the excess beads with a knife – and the look is pleasing to the eye again..

Smooth corners of skirting boards can be cut without the help of a miter box

A neat corner in the room, formed with the markup

The markings will help you cut the skirting board neatly and evenly

  • Gmail
  • Odnoklassniki
  • Whatsapp
  • Viber
  • Telegram

Docking corners with a miter box

  • A miter box is a carpentry tool that allows you to cut various materials that are subsequently planned to be mounted together at right angles.

There are two main designs of the miter box:

A simple miter box is a wooden (plastic) tray with vertical slots in the walls, into which a hacksaw will be inserted. This design allows precise vertical trimming of the skirting board at an angle of 90 or 45 degrees. In addition, it is convenient to work with such a miter box, because it is possible to carry out a hacksaw not only a vertical cut, but also with a blade inclination of 45 degrees..

The miter box with a swivel mechanism is a professional tool, it allows you to fix the hacksaw blade at any desired angle. If an ordinary miter box is suitable only for cutting skirting boards for docking at a right angle, then with a swivel mechanism – for mounting at any angle.

Miter box with swivel mechanism

Ceiling plinth: how to make the corner beautiful and even

Neatly designed corner of the skirting board

The installation of a ceiling plinth is the finishing touch, giving the overall completeness and integrity of the upper decoration of the room. This detail not only adds aesthetics to the room, but also allows you to hide the technical gaps, specially made taking into account the thermal expansion characteristic of finishing materials. With the general sufficient ease of installation, one detail – the corner joints, causes the greatest difficulty. If performed incorrectly, it will not only look foreign and unattractive against the general background, but also spoil the overall favorable impression of the repair.

How to cut the corner of the ceiling plinth and correctly join the plinth – look at

Related materials:

Skirting board for a stretch ceiling: types of structures and 60 photos of stylish incarnations in the interior

Lavender (52 photos): planting and caring for a wayward and beautiful plant

How to make a rose out of paper with your own hands: 4 simple techniques

How to make a fireplace out of boxes with your own hands: step by step instructions and 60 simple decor ideas

Decorative fireplace portal: how to make a stylish false fireplace with your own hands?

How to make furniture for dolls with your own hands: 50 photos, useful tips and life hacks