Technology of installation of curb tape in the bathroom. how to glue the joint
The problematic places in the bathroom are well known to hostesses, they are joints between plumbing and the wall, the corners, where there is a bath or shower, the adjacency of the sink and the wall. No matter how much you smear them, no matter how much you paint over them, after a while new “blossoms” will bloom. But there is a good chance to overcome “blooming”. Not so long ago bathroom curb tape came into the market.
This is a relatively new product, which has already been appreciated by housewives. Curb tape can improve the design of the room for hygiene procedures. Its main purpose. to protect hidden and inaccessible places from the penetration of moisture, to seal and not to allow moisture to get under the tub, a sink, a countertop. And this will entail the eradication of mold, mildew and other nuisances caused by the constant presence of damp. The main advantage of the product. ease of installation, it can be installed independently by any owner of such a room.
Characteristics of curb tape
Curb tape for sealing the gap is a wide strip of polymer material. The edges of the strip adhere to the bathtub rim and wall, forming an airtight connection.
The polymer layer is coated with a hot melt adhesive that provides strong adhesion (bonding) to the surface of the bowl and tile. The strip curb material is resistant to moisture, detergents and mildew.
Sanitary tape can be used to seal the joints of the bathtub, shower cabin and sink. They can be glued to faience, metal and acrylic products.
When to use self-adhesive curb tape for the bathroom, consumer reviews
Some owners during the repair set the bathroom bowl as close to the wall as possible, and then believe that there is no need to seal the seams. This statement is completely wrong, because in any case, there are small gaps through which will penetrate and unnecessary moisture under the sanitary device. Most plumbers consider it necessary to seal seams, the width of which is 1.5 mm or more. This is explained by the fact that such slots become a place where water droplets constantly, though in small amounts, penetrate.
Installation of the tape does not take much time and does not require significant financial expenses
Important information! Fungus and mold not only spoil the attractive appearance of any bathroom, but also cause unpleasant odors, and in some cases provoke the development of certain health problems, including respiratory diseases and allergic reactions.
Properly selected sealant for the bathroom helps not only to save health, but also to save time on cleaning the room due to the fact that you do not have to constantly clean up mushroom spores, which are distinguished by an unattractive black color. The more so that in most cases the installation of the tape does not take much time and does not require large financial expenses.
The construction market does not stand still: new materials are constantly being developed to make repair work easier. Plastic curb tape. a convenient device that provides quality sealing and prevents water from getting into large gaps and even small cracks. According to reviews, curb strips are distinguished by a number of advantages:
Guardrail tape has such advantages as reliability, ease of installation, resistance to damage, low price
- Affordable Everything depends on the chosen parameters.
- Reliability. The use of the material ensures a reliable seal between the wall and the bathtub if the installation rules are followed.
- Easy installation. Thanks to its high elasticity the curb can be installed not only on an even surface, but also on a curved one.
- Easy installation. The material is fixed on a ready-to-use adhesive base, which makes it possible to quickly and easily apply it yourself without the involvement of a specialist.
- Good resistance. The adhesive tape for the bathroom is highly resistant to mechanical injuries. Even pitting or depressions do not form on the curb.
- Easy care. The product does not require any special care or the use of specific cleaning agents. For cleaning it is quite enough to use a standard detergent for cleaning sanitary ware. Important is not to use aggressive abrasives or harsh brushes.
- Moisture repellency. Correctly installed tape allows water not to accumulate on the rim of the bath, shower cabin or sink.
- Environmental safety. The material does not contain toxic elements that can be harmful to health.
- Wide assortment. A large number of products on the marketplace will help you choose the best option (from a structural and aesthetic point of view). It is possible to buy bathtub edging strips of different colors, shapes and sizes.
Properly selected curb tape for the bathroom helps to prevent the appearance of fungus and mold
The main disadvantages of self-adhesive tapes for the bath
The basis of all tapes for sealing is PVC film, which is durable and particularly elastic. Even so, damage and scratches are possible if constantly exposed to hard particles. In addition to advantages, the products have some disadvantages, which are not significant, but nevertheless they need to be aware of them before the start of installation work.
Among the main disadvantages of waterproofing tapes for bathrooms are short life. In most cases, the service life will depend on the characteristics of care, the intensity of use of the bathroom and the quality of ventilation made. The average operating period is in the range of one to three years, which is significantly less than other types of curbs, such as plastic or ceramic tiles, used for the main finish of the walls.
The disadvantages also include the difficulty of replacing the damaged tape with a new one. In addition to buying new material, which entails some financial costs, you will have to make physical effort and acquire certain skills. Replacement requires not only to remove the self-adhesive curb tape, but also to get rid of the remains of sealant on the wall and the surface of the bath. To perform this procedure, it is recommended not only to clean and degrease the surface, but also to choose the optimal sealant, because the adhesive composition on the tape is not used together with acid silicones.
Important! If before you glue the curb tape, apply silicone with an acidic composition to the surface, the material will not only peel off, but also lose its shape.
The main disadvantage of curb tape for the bathroom is a short service life
The disadvantages may include a limited choice of color design. Most products are presented in pastel colors: most often it is white, which is considered the most common color for finishing the bathroom. If you need to install a black, gray or colored tape, you will most likely have to contact the distributor to order a custom production.
Bathroom edging tape: the main types of material
The composition of the sealant is determined by its main function, which is considered the protection of a certain surface from the influence of moisture. Constant exposure to water causes the development of fungus, mold and reproduction of other harmful microorganisms. That’s why only waterproof and water-repellent compounds are used for the production of self-adhesive curb tape. Most manufacturers use polyethylene for that purpose, much less often synthetic polymer is used as a base.
For better adhesion to the surface on the basis of the curb is applied adhesive mixture, characterized by resistance to temperature changes and constant exposure to water. Leading manufacturers also additionally treat products with special chemicals that repel pests, such as various fungicides.
Border tapes are only made of waterproof and water-repellent compounds
This is interesting! Until recently, to seal joints in the bathroom were used only silicone or even cement mortar. On how long the sealant dries in the bathroom, not only affects the type of material, but also the conditions in the room: temperature and humidity. On average it takes from 6 to 24 hours for the liquid sealant to harden completely.
Before installing the curb strip, the surface should be well cleaned. Installation of a flexible strip does not take much time, but nevertheless the appearance of the bath will be more attractive than after the application of silicone. Many users note that they hide irregularities and other flaws in the joints, which is especially relevant when it comes to an uneven surface. Bathtub tapes have a wide range of applications, due to the fact that the material differs in such parameters as:
As for the shape of the profile, the tapes are divided into two main groups: angular and shaped. Corner models are distinguished by the presence of a bend in the central part of the product, allowing you to properly and evenly attach the curb to the vertical surface and the edge of the bath. This product is suitable for closing not wide gaps and adheres well to a base made of basic materials used to create sanitary fixtures, such as
Border tapes according to the shape of the profile are divided into angular and shaped
A distinctive feature of shaped bath tapes is the presence of two lines of inflection, dividing the product in length into three segments. It is important to know that there is no glue applied in the central part, because the main task of this part of the curb is to hide the wide gap between the curb and the wall. Only the edges of strips are glued. In order to choose the right shaped tape, you need to determine in advance the width of the gap, which you want to close with the product.
The main variants of sizes and designs of self-adhesive edge strips for bathrooms
There is a large selection of sizes of curb strips for bathtubs on the marketplace. The average length is 3.2-3.5 meters, which allows you to choose the right option, regardless of the size of the sanitary ware. If this length is not sufficient, two separate rolls of tape must be purchased.
According to the width, curb strips are divided into the main groups shown in the table:
| Size, mm | Destination |
| 10х10 | For narrow joint gaps |
| 20х20 | Used to seal medium size gaps |
| 30х30 | Conceal large openings |
| 38 | Oversize |
| 60 | Custom size of the border tape, allowing to hermetically cover large gaps between the wall and the edge of the plumbing fixture |
Useful tip! Plumbing experts note that before using a curb strip, you should carefully measure the parameters of the gap. Optimal is considered the installation of the curb, the size of which exceeds the gap of not more than 5 mm. Overly wide strips will look unaesthetic, and too narrow will not provide reliable sealing.
Most often it is white products that can be found on sale, because this color is considered a universal and the most popular in the arrangement of sanitary facilities. As for the choice of sanitary ware, then most often there are devices in this color. The same trend can be found in the choice of material for vertical and horizontal surfaces. Although, in addition to white tapes, you can find products in light pink, soft green and creamy beige. It is recommended to choose the suitable shade based on the color of either the plumbing fixtures or the surrounding walls.
Some manufacturers use curly edging and embossing to make the tape attractive. These options for decorating especially help to play and complement the interior of the room.
Advantages of using curb tape
In addition to cheapness, self-adhesive edging tape has a lot of other advantages. First of all, the material provides excellent sealing along the entire length due to the adhesive composition, which at this price is an excellent alternative to expensive profiles.
Other striking advantages of using border tape include:
- Elasticity. the tape material is very soft, elastic, which allows you to apply it to joints of different lengths and shapes without any problems;
- Fast installation. it does not take more than 2 minutes to install the self-adhesive material, and the tape is perfectly glued and evenly laid along the entire length without using special tools and calling a specialist to the house;
- Variability of installation. the elasticity of the material allows you to stick the material not only on a flat, but also on a structured surface;
- Environmentally friendly and safe. despite the composition of the adhesive, the tape is made on the basis of clean, environmentally friendly materials, harmless for people and the environment;
- Affordability. unlike other finishing materials, the adhesive tape is much cheaper, with a very extensive range of all colors, shades and shapes;
- Reliability and durability. with proper installation and proper care, this material will last more than a year without the need for constant replacement;
- High resistance indicators. the curb tape is a rather strong material with good water and heat resistance as well as resistance to mechanical impact and influence of chemical reagents;
- Easy care. unlike other finishing materials, edging strip does not need regular care and special cleaning, to maintain its normal appearance it is enough to wipe it periodically with a standard cleanser without aggressive chemicals and harsh brushes.
The advantages of this finishing material abound, but despite this, the adhesive tape has disadvantages that should not be missed.
Disadvantages of curb tape
The main disadvantage of curb tape is its short life. The lightness and elasticity of the material, which for the most part consists of PVC filler, makes the tape not strong enough, prone to scratches and damage. Another disadvantage of the material is considered a limited color range. Most manufacturers produce rolls of standard colors, which in some way limits the design solutions using this material.
Important! The service life of the waterproofing tape depends not only on its type, but also on the conditions of care and use of the material. If it is cleaned frequently with chemicals, it can lose its color and shape much sooner than designed.
Another significant disadvantage of using edge waterproofing tape is the difficulty of its replacement. Thanks to the adhesive composition, the material is very strongly penetrated into the surface of the bathroom, so it is difficult to remove it without scratches and traces of glue. To replace the old tape on the new one, you need a special tool and solvents to remove the remains of adhesive.
Ceramic curb installation
Despite the fact that many frighten by the complexity of the work on tiling, if desired, you can still do without the help of professionals and perform the installation yourself. Having studied the information on how to make a ceramic curb in the bathroom, and proceeding to install it on the sides of a cast iron or acrylic container, you will understand that there is nothing complicated in this case.
What you will need for installation?
Preparation of the surface for ceramic curb installation on the laid tile is not different from the installation of curbs from other materials. Angle on top of the cladding is installed on “liquid nails”, the process itself is very similar to the installation of a plastic product.
To hide the ugly end of the corner, special plugs are used. They create the impression of a smooth transition from the bathtub rim to the curb
Calculate and purchase the material before starting work. Since when you cut the tiles it can split, you need to take a slightly larger amount than necessary. In addition to straight sections, you will also need corners and plugs.
Corner elements of ceramic edging can be in the form of a triangle or a regular element with a cut angle of 45 °
To carry out installation you need to prepare water-resistant tile adhesive, sealant, grout. From the tools comes handy a special gun for applying foam, sanding block, spatula, angle grinder.
Step-by-step description of the work
Ceramic curb can be installed during wall tiling. or in other words “under the tile”. In this case, the subsequent row of tiles can be bent after laying the corner, and can first be laid the upper row, and already after, under it, set the curb.
The work on the seal is performed in this order:
- Prepare tile adhesive. The proportion and technology of preparation may differ for each brand, so you need to follow the instructions.
- Start the installation from the corner and use the special corner elements for this purpose. On the back side of the ceramic workpiece with a trowel apply such an amount of glue, that it fills the space under the curb and protrudes a little bit on top. Remove excess glue later with a trowel.
- Rectangular elements are pressed evenly to the surfaces, if necessary “sink” some side a little more, it is tapped with a rubber mallet.
- The next tile is placed in the same manner. If you need to insert an element of smaller size, it is cut with improvised tools. This can be a tile cutter, angle grinder with a diamond disc or a regular glass cutter (they cut the glaze, and the tile is evenly broken off in the place of the cut). The place of the cut is grinded with a flat bar.
- According to the technology, the next day it is recommended to wet not yet fully cured curb, so that the glue hardens properly.
- After finishing tiling, before the glue dries, wipe the tiles with a damp cloth.
- When the glue under the curb cures, the joints are applied waterproof grout or silicone sealant. After that the curb must be wiped off again.
To protect the tub from the accidental fall of heavy elements, it is covered with cardboard boxes (preferably over the entire surface). They can be secured with duct tape.
How to glue the flexible tape?
All works with flexible self-adhesive edging should be performed at the temperature not lower than 10 °C. It is mainly used after installing steel bathtubs or acrylic containers. The tape itself should not be stored at sub-zero temperatures. When buying it, also pay attention to the shelf life. an expired product loses its adhesive properties.
The width of the product is chosen depending on the size of the joint. After preparatory work on the filling of gaps between the bathtub and the wall, to clean and degrease the surface, take the measurements from the bath and cut the corners by 0.5-1 cm longer than the required length.
The most difficult thing in installing a flexible curb. carefully arrange the tape in a corner to make an even cut at an angle of 45 °, without allowing the formation of gaps
To seal the joint in the bathtub with self-adhesive tape perform these actions:
- Tape is bent along the longitudinal line, which is specially provided for this purpose.
- Glue a flexible corner, gradually removing the protective film, starting from the corner. Do not remove the entire film immediately. a long piece of tape will cling to the tub, and the adhesive coating will deteriorate. To better fit the element, in the place of the longitudinal fold, press it with a flat object, such as a trowel, taking care not to damage it.
- After laying the corner, once again pass along, pressing down firmly with his hands to the bathtub. Do not iron the tape to prevent it from stretching. All the time you need to control the tightness of the fit, especially in places of deepening of the tile joints.
- The next piece also begins to glue from the corner, laying it on the previous one, overlapping. After the second element is firmly fixed along the entire line, cut the overlapping strips. With a sharp knife, starting from a corner, lead the knife at an angle of 45°, making the cut.
It takes 24 hours for the adhesive to dry on the flexible tape. At this time you can not use the bathroom and keep water on the curb.
If the sides of the bathtub allow, it is better to choose a wider flexible self-adhesive tape. so there is less chance of water seepage under the sealant
For better adhesion of the curb with the surfaces of the wall and bathtub, after laying it is heated with a hair dryer and once again pressed along the entire length by hand. Under no circumstances should this be done before laying, otherwise the tape will start to stretch and deform.
To extend the life of the tape, the laying process can be improved. To do this, remove the protective film from its surface, peel off the layer of adhesive applied by the manufacturer, and install it on a silicone sealant.
Sequence of operations and installation technology can be seen in the section describing the laying of plastic curb. they are completely identical.
Removing the curb tape step by step
To remove the adhesive tape, you will need a plastic spatula and adhesive residue remover. As a solvent, you can use acetone, white spirit, alcohol solution.
The removal process itself is as follows:
- Pick up the edge of the plastic curb tape with a plastic trowel.
- Use a spatula to remove the tape.
- Apply solvent on a cotton pad.
- Scrub the surface to wipe off adhesive and material residue.
It is important to use a plastic trowel, as a metal trowel can increase the risk of damaging the surface.
How to remove adhesive residue from curbstrip
After removing the old self-adhesive edging tape from the bathtub, there are often yellow traces of glue. To get rid of such defects is sometimes very difficult, but it is possible with a competent approach. You can gently remove the remains of the tape or glue without damaging the surface with the help of various improvised means, the choice of which depends on the type of tape and glue used.
Here are the most common options for removing adhesive residue from different surfaces:
- Acrylic is easy to damage, so to carefully remove traces, it is best to use an alcoholic solution of high quality, but never acidic solvents;
- Glass. quite easily cleaned with ordinary white spirit;
- Silicone. silicone remover will perfectly remove any traces;
- Ceramics. with acetone or vegetable oil;
Other types of surfaces. traces of glue is easy to remove with boiled water, excellent dissolving glue, enough to give the surface a boiling water and immediately rub with a brush before the glue has time to solidify again.
When cleaning different types of surfaces from adhesive residue, pay attention to the tools used. Delicate surfaces, such as acrylic and ceramic, is best cleaned with rags, cotton swabs, but not a hard brush.
Self-adhesive bath tape
When the bathroom is being renovated and tiled, when installing plumbing fixtures against the wall, unevenness and gaps at the junction with the tiles are formed. Even if the gap is very small, there is still a high probability that the gap will be filled with water from the bath or washbasin. This is fraught with the risk of dampness, mold and mildew. With a minimum clearance for sealing silicone is used, however, and it contributes to the formation of irregularities, where gradually will accumulate dirt, mold will arise, and the bathroom will have an unsightly appearance. To prevent any of this from happening, they came up with a special self-adhesive edging tape for the bath.
Tape edging for the bathroom has high performance qualities, which is explained by its targeted functionality. This device is perfect: it does not let water in, the joint will never appear fungus, in addition, the product has a pleasant aesthetic appearance, it is easy to attach and remove after the expiry of its operating life.
The thickness of the tape is 2 mm, it is produced in hermetically sealed rolls, and the leftovers can be used in other places. It is used for processing and decorating the joint:
The entire surface of the curb tape is glued, so it cannot peel off anywhere. Both domestic and foreign manufacturers produce it.
The tape consists of various components, the main ones being special fungicides. They are the ones that prevent the appearance of fungi at the joint. It also has great performance qualities, such as moisture resistance and impermeability, so there will never be dark streaks under the tape. Although it is a temporary sealant, it can be replaced many times after its service life expires. The material of which the tape is made does not swell under the influence of water and does not crack due to its absence, so it remains elastic until the end of its useful life.
Curb tape has a variety of color shades: blue, beige, green, pink, black, gray, white.
Advantages of edging for the bathroom
The edging strip is an available material, which is easily and quickly applied. Its main advantages are:
- the bathroom has a pleasant appearance;
- The absence of mold and mildew in the process of operation;
- the joints of sanitary products have an excellent sealing;
- The tape does not crumple and well withstands any loads;
- has an optimal ratio of flexibility / rigidity;
- After the cuts, it will not peel or peel off;
- its installation is very simple;
- high quality at a low price;
- Resistant to the chemicals used to clean the bathtub;
- The seams and joints are absolutely invisible;
- it can be used in bathrooms with high humidity;
- resistant to temperature fluctuations, as well as to various damages and impacts;
- has a high plasticity, as a result, it can be bent at an angle when laying, as well as laying on rounded and curved joints;
- it does not deform under load;
- fits snugly on slippery surfaces.
Disadvantages of the curb for the bathroom
However, self-adhesive tape for the bath has disadvantages:
- It can warp from contact with acidic silicones and assembly foam. In addition, the acidic environment contributes to the fact that the tape can peel off from the contact surface. This must be taken into account when using a flexible curb;
- Relative to hard surfaces, this elastic material is short-lived;
- Curb tape is an inexpensive and effective tool, but is considered a temporary material. It can be used for about a year, after which the section should be replaced with a new one.
Basic installation rules
Before proceeding to install the bathtub curb, buy the necessary width of tape, taking into account the gap between the bathtub and the wall. The surface on which the curb will be glued, must be dry, so it should be wiped with a clean cloth. In the gun is inserted aquarium sealant for the bath, with its help isolate the gap and wait until the silicone dries.
Although the surface of the strip edging has already been glued, it is still recommended to use liquid nails. To avoid damaging the enamel with the projecting glue, the edge of the bathtub should be glued with masking tape.
Measure a piece of tape of the desired length and apply liquid nails a thin layer on its surface, then one edge should be pressed very firmly to the wall, and the other. to the bathtub. On how tightly the tape was pressed, depends on the quality of adhesion and its lifetime. Then seal the joints of the curb on the corners with sealant.
Thus, the installation of the bathtub curb is considered complete. It must dry within a day and you must make sure that during this time, it does not get water.
The main nuances of gluing
Self-adhesive edging tape will help in cases when you want to quickly bring the bathroom to normal condition, so that the sink and bathroom have a neat look. However, you must remember that even with quality care, such a curb serves no more than two years. But still, it is a great way to make such a room quite comfortable.
Such a tape under the force of almost everyone, but still you should take into account certain nuances:
- Be sure to clean the surface of the wall and bathtub of grease, dirt and water before gluing the tape curb. If you have to re-adhesive it, it is necessary to remove the remnants of glue from the previous tape. To make the surface dry and smooth, you should use soda, alcohol, cleansers, as well as a hair dryer;
- The curb must be cut in such a way that the cut was 2 cm longer than the laminated surface. If difficult areas are to be glued, an incision must be made in the corner of the tape on the side adjacent to the bath;
- Start gluing the tape is best from the corner, while it must be pressed very tightly to the tub and tile;
- After finishing the work, you must avoid getting water on the curb tape for a day, until the glue dries.
The joints between the bathtub and the wall must be sealed. Use a variety of moisture-resistant materials for this purpose. To do everything quickly, cheaply and without using specialists for such work, the curb band is used as the best and most practical option. As a result, the bathroom is literally transformed.
What is a self-adhesive tape edging made of??
The base of the material. synthetic polymer, usually polyethylene. It is 100% waterproof, so the tape can reliably protect the gap from getting wet. The self-adhesive tape edging is butyl-based adhesive on one side. This adhesive securely attaches the tape to the wall and the edge of the bathtub, is not afraid of exposure to water. Some models include a special plastic applicator. It helps to achieve a perfect fit to the surfaces and create the correct right angle.
Important! Many manufacturers when making elastic edging include fungicidal additives in its composition, which prevent the appearance of mold.
Bathroom edging tape is not standard, and is available in a variety of colors and sizes. Therefore it is always possible to choose the most suitable product.
Advantages when using tape
Numerous user reviews tell about the positive sides of this method of joint sealing. The main advantages of the flexible curb:
- Low cost.
- Quick installation. Any person can glue elastic curb.
- Reliable sealing against moisture penetration.
- Reliable attachment to surfaces thanks to the adhesive that is applied to the entire surface of one side of the tape.
- Resistant to all kinds of mechanical damage, does not crumple.
- High elasticity. Bends at any angle without cracking.
The disadvantages of the material are manifested in its short duration. The flexible edging for the joint in the form of tape, unlike the ceramic edging, which can serve more than a dozen years, will have to be replaced after 2-3 years. However, this drawback will not be such a serious obstacle to the purchase of the tape, especially since the installation is simple, and the cost is affordable.
How to choose a quality colored curb tape
To choose a high-quality colored edging tape, it is advisable to buy it in shopping centers, as it should be stored at a temperature not lower than 10 degrees, otherwise it loses its adhesive properties. The shelf life should not exceed 2 years. Do not expose the tape to open sunlight. Particular attention should be paid to the integrity of the packaging. Spoiled or torn packaging can make the product unusable.
You can glue the curb tape on the bathtub yourself. You do not need to have the skills of a professional repairman to do this.
How to properly glue the curb on the bathtub
In order to properly, efficiently and without problems glue the curb tape, it is necessary to follow a certain sequence and adhere to the rules.
Preparing
One of the main requirements for the application of scotch tape is a solid base. Therefore, if there is a gap between the bathroom and the wall of more than 1 cm, it must be sealed with tile adhesive or sealant.
Remove excess glue from the surface with a rubber spatula.
Important! It is categorically forbidden to use acid silicone, as it can lead to the deterioration of the curb tape. It is better to use acrylic and neutral silicone compound.
After the glue dries, it is covered with a primer and dried again.
Remove the dust from the seam with a dry clean cloth and you can begin to mount the adhesive tape.
If the seam has already been sealed earlier, there is an opportunity to save time. It is enough to clean it with fine sandpaper, then degrease with alcohol (it is better not to use acetone, because it destroys the adhesive layer of the tape), wait until it dries and you can paste the tape.
Most manufacturers produce white borders, because this material is universal.
Attaching the tape
The process of installing self-adhesive curbs for the bathroom can be divided into several successive steps:
- To begin with, it is necessary to measure and cut off the correct length of the tape. To do this, you need to take it and, while placing it against the edge of the tub, measure and cut off the required length with a sharp knife.
- Then about 10 cm of the protective film on the side with the adhesive base is removed from the tape, and you can begin pasting. As a rule, it is recommended to begin gluing from the corner. It is necessary to press the tape to the seam surface well, especially tightly in the corners. So, gradually removing 10 cm of the protective film from the adhesive layer, paste the entire surface of the seam.
- Once the entire tape is glued, it is necessary to take a sharp knife and make a trim in the corners. And you must do it with two halves at the same time, cutting them at an angle of 45 degrees in the direction from the corner to the bathtub.
- After the final stage of laying the tape-angle should be left alone for 24 hours, it is strictly forbidden to get water in this area.
- If, suddenly, after a day in some places summer is still badly adhered, it can be tucked liquid nails and again wait for drying.
Self-adhesive edging tape for the bath has an important and useful feature. on the back side of the material is applied adhesive composition.
After a day, you can quite confidently use the shower and do not worry about the fact that the water can flow under the bathtub.