How to cut plastic skirting boards on the ceiling

What is a plastic ceiling plinth and when is it used??

It would seem that with the abundance of different types of polyurethane and polystyrene decor, why should we use a plastic skirting board?? However, there is a place for such a decor.

Its main area of application. design of plastic ceilings. This is what it is primarily designed for. Such ceilings are very popular for finishing rooms with high humidity. But when assembling them, inevitably there is either a small gap between the wall and the ceiling covering, or just not too neat a joint. This is where you need a plastic fillet. This element will hide all the defects, and in some cases can serve as a fixing element.

What is it

Made of the same material as the panel itself. PVC. Therefore they are called. PVC skirting boards. In form such plinths are very similar to the standard L-shaped fastening profile. Differs from the simple mounting profile only the presence of decorative design.

And from the standard polystyrene or polyurethane boards, plastic skirting boards differ in the presence of a fastening element in the form of a groove, where the edge of the panel is inserted.

When the ceiling is mounted, it is this additional element serves to tighten all its parts. However, do not fix the panel only on them. it will not be strong enough.

An interesting place to use such products is at the joint between the panel and the other material. This is the case when the first wall is attached PVC slats, and the second is finished with another material. In this case the skirting board will be of great help. On the first side will be inserted slat, and the second side will fit tightly to the other type of coverage.

The only difference will be that it will not be located horizontally, but vertically. There will be no other differences, neither in installation, nor in anything else.

How to cut a skirting board for a right angle

The most convenient way that virtually eliminates the appearance of inconsistencies is to use. This device is a U-shaped template with slots in the side walls, made at different angles. The baseboard is marked on the spot, noting its maximum length along the ceiling for outer corners and along the walls for inner corners. The skirting board is laid in a notch, aligned and cut at a 45 degree angle.

In the absence of a jig, you can make a template of cardboard or heavy paper, drawing lines at an angle of 45 degrees on it with a protractor. The baseboard is placed parallel to the edge of the sheet to the marking lines and is cut with a sharp knife using a ruler.

If one section of the baseboard needs to cut a corner on both sides at once, it is recommended to start with the more difficult. the outer or uneven corner.

What to do if the inner corner is not straight

The walls in our houses are not always perfect, and the angle can be more or less than 90 degrees. In this case, a standard template will not work, and it is better to use the marking on the spot. You will need a hard pencil for this. it leaves fewer traces on the ceiling.

The baseboard is attached in turn to each of the walls that form the corner, and draw a trimmer line along its edge on the ceiling. At the intersection of lines on the baseboards make a mark. Connect it to the bottom edge of the baseboard at an angle and cut the corner with a knife using a ruler. The baseboards cut in this way fit evenly into any corner.

Tile with stucco is difficult to dock in the corners without the use of special corners, but if you were not able to pick up fittings to the relief baseboard, you should not despair. with the help of the above methods you can properly cut a corner on the ceiling plinth of any shape. It is better to join a skirting board in a place with the most protruding elements of a stucco so that the general drawing is not broken, and the joint is carefully glued. In this case the baseboards will look neat and blend perfectly into the design.

When installing a skirting board, the most difficult task is to finish the corner areas. Baseboard strips are to be cut into individual elements, according to the room perimeter. Experts recommend that you pre-draw a visual installation diagram on paper, paint all the dimensions, as well as schematically depict how to make the corners of the floor plinth. With such a clue at hand, finishing work will progress much faster.

How to cut a corner without a joiner

Cut the corner and glue the baseboard can be done without a pitching tool. Let us tell you how not to spoil the appearance of the baguette.

  • On any solid basis draw a line for the trimmer.
  • From the line makes an indentation of 10 cm and draw another line for the trimmer.
  • At right angles draw a line through the parallels.
  • From the line on each line make a 5 cm mark and connect the lines to the opposite points.
  • Lines with parallels will eventually form a 45-degree angle.

Thus we get a homemade plinth, and now it’s necessary to determine the slope and make the cut of the skirting boards.

  • Boards we attach to the ceiling and determine the direction of the cut for accurate and correct installation.
  • For the inside corner the upper edge should be shorter than the bottom one.
  • For the outside corner the top edge should be longer than the bottom edge.
  • It is necessary to cut baguettes in a mirror reflection.
  • On the baseboard, which will be located on the right, you must make the cut on the left side. For the trim, which will be on the left, the cut is on the right side.
  • We put the slats on the self-made crosscut saw along parallel lines and, taking into account the direction of the angle, make the cut along the marks.

To make the cut without roughness and splinters, it is necessary to advance the knife carefully in one direction.

How to glue ceiling skirting boards to different surfaces

It is quite easy to glue the ceiling skirting board, it all depends on the material of the ceiling and walls.

Stretch ceiling

Today, many people choose stretch ceilings for finishing, so they are interested in how to cut the corner and glue the ceiling plinth so as not to damage the material. For stretch ceilings is worth choosing lightweight and narrow baguettes. These are skirting boards made of foam plastic or polystyrene foam. You can also consider plastic or polyurethane options.

To avoid getting glue on the stretched material, you need to apply it to the part of the molding that is fastened to the wall, not to the ceiling.

Glue is worth buying with the most reliable fixation, which dries quickly. But you need to work carefully with any compound, so as not to spoil the canvas. If the baguette is large or made of wood, it will have to be additionally secured with anchors or dowels.

Before you decorate the wall with a ceiling plinth, you need to check how securely the wallpaper is glued. In those places where they peeled off, be sure to fix them with PVA glue or wallpaper, and then leave them to dry completely for 1-2 days. On the peeled wallpaper baseboards can not be glued, otherwise they will fall off with the wallpaper.

Ceiling skirting boards put on the glue with a good fixation, and in order not to get dirty with adhesive wallpaper, pre-mark the entire width of the strip. And below the drawn line glue a masking tape, which is then easy to remove.

Drywall

It is very easy to glue ceiling skirting boards to gypsum board, because this material has a flat surface. The only difficulties may arise at the joints, where the putty under the influence of glue can give runs. Such a problem is easy to solve, just sandpaper the joints.

Gypsum board reduces space, but if you glue the skirting boards to the ceiling with a wide side, the room will visually seem larger.

Plastering

Before gluing a skirting board to a wall with this finish, it is important to check their evenness. If there are defects, they must be sanded down or sealed with putty. You can also hide irregularities with a special soft plinth.

If the defects are significant, then the walls must necessarily level, apply primer and grind.

A few recommendations

Any work has nuances, but they can not be perceived as trifles. To trim passed accurately and without problems, it is necessary to pay attention to a few moments.

  • Correct measurements are the most important thing in any job. To mark the blanks for the inner corner, the measurement begins precisely from it.
  • Before cutting both planks for the outer corner, do not forget that they will “look out” for a length equal to the width of the products.
  • Fixing the ceiling baguettes begin only after several checks carried out. When the edges of the skirting boards fit perfectly, then you can begin to glue them (fixing screws).
  • One can use files or files to correct jointed blanks. For foam plastic and both types of Styrofoam it is necessary to take thin, sharp-sharpened blades.

As any debut rarely passes without mistakes, it is recommended to start with training on scraps. Therefore, when buying, it is better to add 10-15% to the length of the products. So you can guarantee that the material is enough not only for the preparation, but also to the entire room, even if flaws in the process still appear.

What to do if gaps remain?

If the defects are detected after the work is completed, few people like the prospect of redoing it. In this case it is easier to mask them with one of the compounds. The best option for this treatment would be a final acrylic putty. It has a white color and is very plastic. The material is taken with the fingers, then it is pressed into the remaining gap, carefully distributing in the hole, smoothing. Remove the remaining composition with a damp cloth. As a rule, there are no imperfections at the joints.

How to cut a ceiling plinth? It is necessary to stock up on the necessary tools and patience, as haste always provokes errors. The main thing in this case is to choose the best method. But attentiveness and accuracy are no less important: baseboards are made of not too strong material (except for wooden baguettes). They are fragile, so excessive efforts when working with such products are contraindicated.

plastic, skirting, boards, ceiling

About how to cut the ceiling plinth, will tell the author of the following video, which viewers consider the easiest and most understandable:

Selection of tools for cutting ceiling plinths

To cut ceiling plinths correctly and accurately, you need to use the right tool for cutting. It is chosen depending on the material from which the fillets are made:

    Styrofoam. Characterized by low strength and costs relatively inexpensive, and therefore foam models are becoming increasingly popular. Their strength does not particularly affect the performance characteristics, because usually the ceiling plinth is not subjected to mechanical stress. An ordinary office knife is suitable for cutting.

It can be purchased in a construction store or make your own hands according to these instructions:

    Three 5015 cm boards are nailed with a long edge into a shape of a three-sided rectangular box. Please note that there must be a 90-degree angle between the side boards and the cross-cutting plank.

To work with this homemade device was convenient and safe, the planks should be well sanded before fastening.

Technology of cutting ceiling plinths

For prompt and high-quality work, you need to choose a tool in accordance with the material of the baseboard and choose a way of cutting. If you have a jig, then there will be no special difficulties in the process. If it is not present, then you have two options: to cut by the template and measurements on the ceiling, or to make this tool yourself.

Features of cutting ceiling plinths in the jigsaw

Work with this device should be extremely carefully not to blunt the tool and not to leave cuts in unnecessary places. In the process, follow the following instructions:

    Fix the molding in the jig as it is planned to place it on the wall. The side that will be pressed to the ceiling on the jigsaw should be adjacent to the sidewall.

When cutting and trimming foam and polyurethane products, remember that these materials are crumbly and pressed, so tools must be sharp enough, and strong mechanical action on them is undesirable.

Technique of cutting ceiling plinths by template

This method can be used in that case if corners at you. are equal, and it is required to trim a molding exactly on 45 degrees. To do this, before you cut the ceiling plinth in the corners, you need to draw a jig on heavy paper. Draw two parallel lines and mark the angles at the right degrees, using a protractor.

We place the fillet in this case the same way as in a traditional chair. Note that you must cut the skirting boards holding the tool in a strictly vertical position.

plastic, skirting, boards, ceiling

Rules of cutting ceiling plinths by marking

This method is used to cut the skirting boards in cases where there is neither a chisel, nor parts from which it can be made.

To do this, you need to make a marking on the wall in this order:

    Put the baguette in the corner to the fixing point.

When cutting in this way, it is important to accurately draw all lines and mark points. A mistake of even a few millimeters will cause a gap. This method is suitable for cutting and docking both inside and outside corners of the ceiling skirting.

How to cut a skirting board without a chisel

To accurately join the internal corners of the boards, you can do without a joiner.

    We enclose the end part of the baguette to a sheet of paper and trace the contour of the convex side. It is more convenient to use a small piece of baseboard (if you have one).

plastic, skirting, boards, ceiling

Installing PVC baseboards

Assembling a PVC ceiling skirting board involves installing a frame of wooden slats or metal profiles. Elements of the frame should be attached at a distance of about half a meter from each other. If the wall is level, the profiles are fixed with studs. On walls with defects, it is recommended to use self-tapping screws, making pads under the frame in places of depressions.

Edge elements of the frame will act as a base for fixing the ceiling plinth for plastic panels in the corner joints. The main part of the PVC skirting boards is fixed with self-tapping screws or construction staples. Places of joints are decorated with special inserts, which allow for faster and more accurate installation work. Installation of PVC panels on the main part of the ceiling is fairly simple, each skirting has grooves that do not allow the panel to move sideways.

Advantages of PVC skirting boards

All polyvinyl chloride products have a lot of advantages, plastic skirting board on the ceiling in this respect is no exception:

  • Installing baseboards. it’s a simple job, which can be handled by an ordinary home handyman. To change elements of finishing, it is enough to remove old panels and skirting boards, and fix new panels on the frame.
  • If used properly, plastic products can last a long time, as the material is not afraid of moisture, heat and cold.
  • PVC skirting boards are environmentally friendly, so they can be used as a finishing material for children’s rooms.
  • A wide choice of colors and textures allows you to pick up products for any style.
  • The ability to complete renovation work in the shortest time possible.

Renovation of premises with PVC panels and skirting boards saves time and efforts, makes walls and ceilings look beautiful and durable.

How to install PVC ceiling plinth. fastening instructions