How to cut roller blinds to the width yourself

How to shorten the length

Most often, adjustment of roller blinds along the length is not required, since it is enough just not to unwind the canvas to its full length

But if you are a perfectionist and it is extremely important for you that the blinds are of the right size, then follow these instructions:

  • Hang the curtains, lower the canvas, wait for it to fully unfold and lie down neatly, then take measurements.
  • Mark where you want to crop the canvas.
  • Remove roller blinds, spread them out on a horizontal surface.
  • Remove the weight from the bottom edge.
  • Add an allowance of 40-50 mm to the measured length to create a new “pocket” for the weight.
  • Cut the fabric.
  • Place a canvas underneath the curtain and sew a “pocket” for the weighting agent, insert it.
  • Hang the curtain on the window.

If the length of the “excess” fabric is not too long, then trimming can be dispensed with. It is enough to make a double fold of the fabric, with which you can hide up to 30 cm of fabric. This option for shortening the roller blind is much easier and faster..

How to shorten horizontal blinds?

Horizontal blinds can also be tailored to the desired size. The process will depend on how you need to shorten the blinds: in length or width..

If you need to reduce them in width, then you can simply cut off the excess number of lamellas. This can be done without even removing them from the window. First you need to determine how much shorter you want to make the product. To present this more clearly and not to be mistaken, you can make a mark in any convenient way on the window frame (for example, attach a piece of colored tape at the desired height).

Diagram of horizontal blinds.

HOW TO: Cut A Blind To Size

After that, you need to bring the blinds into an open horizontal view. Then it is necessary to release the control rope, which is used for adjustment, from the lowest bar from the latches. To do this, remove the plastic fasteners holding the lace from this strip. You can untie the knots, but it will be faster to cut the rope. To keep it from blooming, you can burn its ends a little. After the fasteners are removed, you need to pull the control rope on both sides of the structure just above the level of the mark that is placed on the window frame.

Now you can neatly remove all the extra planks. In this case, care must be taken that the remaining lamellas do not slip down and do not lose their symmetrical position. The lower bar must be attached to the last lamella and all the others must be passed through it, including through the lowest control rope. The plastic clips must be attached to the ends of the rope as they were originally attached. But before that, you need to stretch part of the ladder, which remained from unnecessary lamellas, into the hole for fastening. Now, if you pull up the retainer and secure it in the hole, the ladder will also be secured. The remaining slats can be removed to the pantry so that you can replace any of those that remain in the blinds.

The process of reducing horizontal blinds in width is quite laborious and requires special tools. To shorten them, you will need, firstly, to reduce the cornice, and secondly, the blinds themselves. To do this, you need a hacksaw for metal and a tool for processing slices..

It will be necessary to collect all the lamellas together, fastening well, and saw off the extra centimeters, and then process their ends. It is quite difficult to shorten such blinds in width by yourself, therefore it is better in this case, nevertheless, to contact the master.

Mix system

A newcomer to the market is the Mix system (sometimes referred to as “bottom-up”). This version of roller blinds differs significantly from its predecessors and, thanks to the original approach, has already gained a lot of fans. The key difference is that, unlike others, the Mix system is installed in any part of the window (most often at the bottom), and not just at the top. In fact, the structure rotates 180 degrees, and the result looks stylish and functional. Installation of roller blinds on a plastic window. The dimensions of the canvas in this case is the distance between the glazing beads. No additional allowances are required.

roller, blinds, width, yourself

The design of the roller blind allows you to close the window both from the top and from the bottom

Installation is carried out as follows:

  • the fishing line is cut into equal parts;
  • all parts are first passed through the upper limiter, after which they are tied into several knots;
  • limiters are attached to glazing beads;
  • free parts are threaded into the holes of the protective box, after which they are attracted to the lower bar, parallel to fixing the upper bar;
  • after the latches on the roller shutter are wrung out, all that remains is to raise the canvas.

Whichever type of roller blind you choose, it’s safe to say that it will look great on the window. Installing a roller blind on a window with your own hands. Of course, the installation of Roman blinds on plastic windows is most often carried out by a specialist, but independent installation is quite a feasible task even for a non-professional..

Read more:  Stihl Fse 60 Replacement Fishing Line

Trimming delicate fabrics

You don’t always need to cut off excess fabric. If the curtains are only 10-15 cm long, then it will be easier to simply bend and sew. However, sometimes it is still necessary to shorten the product. To do this, you need to prepare sharp scissors, a ruler (construction tape) and crayon. An even line is drawn on the fabric, along which it is cut off without lifting the scissors or curtains from the floor. You cannot shorten by weight, otherwise the cut will turn out to be crooked.

Delicate fabrics such as organza or silk cannot always be cut straight. Thin material constantly escapes the scissors. There are 2 methods to shorten the curtain as much as was required initially. This is the pulling of the transverse threads and cuts – the choice of method depends on several factors.

How to cut a roller blind on your own in width

Doesn’t fit the size. How to cut a roller blind with your own hands?

If you cannot find blinds of suitable dimensions in any way and do not want to contact the master for individual tailoring, as it is very expensive, then you can solve this problem on your own by cutting the roller blinds to the required size.

How to reduce the width of horizontal blinds

If the horizontal blinds do not correspond to the width of the opening, they can be reduced by sawing off part of the structure from one or 2 sides at once (for symmetry). It is better to shorten from the side where the control mechanism is located:

  • remove the plugs and protective cover from the eaves;
  • slide the cord system and control mechanism over the pin;
  • measure the desired size, put a mark;
  • carefully fold all the lamellas into one multi-layer strip, clamp them with clamps or an elastic band so that they do not crumble;
  • saw off the excess with a fine-toothed hacksaw;
  • finish the edge with a file or sandpaper so that there is no burr, round the edges a little;
  • reassemble the structure in the reverse order and you can install the blinds on the window.

It is better to modify metal and wooden horizontal blinds on a milling machine, so the edges will be much neater. The cut must be treated with a protective compound and, if necessary, tinted.

Graphic instructions on how to measure the opening in order to properly cut the blinds

The task of how to shorten blinds with horizontal slats in height is simpler:

  • open the bottom bar;
  • untie the knots on the restraining cords, remove the clips;
  • remove excess slats, cut the lace to size and reassemble the blinds in the reverse order.

In order not to make mistakes in the process of work, be sure to watch the video tips on how to shorten the blinds correctly.

Roller blinds are untwisted from the roller, the canvas is removed. The roller is cut identically to the cornice, with a hacksaw. The fabric itself is laid out on the table, neatly traced to the size of the opening plus an allowance for hem on the sides, cut with scissors and the edges are hemmed. Next, put in place the lower plumb rail

So that after the end edge is again glued to the shaft, the curtain does not turn out to be short, it is important not to forget about the allowance, which is equal to the circumference of the tube, usually 50 mm

Scheme of how to properly cut roller blinds

Pulling the cross thread

The second method is recommended when working with simple organza (without embossing) and similar fabrics. It is much easier – you just need to measure the length, make a small incision on the side and pull out any transverse thread. It should be removed carefully so as not to tear. A fishing line is formed (a small gap in the fabric), along which the canvas is cut.

How to cut roller blinds to the width yourself

Roller blinds are most often cut in order to change the design of the room, to decorate, to adjust them in accordance with the dimensions of the window openings. This is necessary when you change your place of residence. If initially your window had the same dimensions, and then you moved into another apartment and at the same time you do not want to buy new window structures, you need to know how to cut roller blinds in width yourself.

Anyone can do this in the presence of an ordinary tool, which is at hand for every housewife. In order to get started, you first need to measure the size of the window. To do this, follow these steps:

  • Hang the fabric on the cornice above the window.
  • Spread out the curtain material, let it hang a little, take the final shape.
  • Make accurate measurements and write down the information received.
Read more:  Trimmer Repair. Do It Yourself.

The length can be reduced in size in a matter of minutes. To do this, simply make a double or triple hem and hide in this way up to 20-30 cm of rolled fabric.

How to trim roller blind to size Install video – with Inspire DIY

We select tools

In order to cut roller blinds in width yourself, you will need the following tools:

  • soap or a special pencil for fabric;
  • household scissors or a sharp stationery knife;
  • needles, threads;
  • tape measure.

If the curtains are too wide, which goes beyond the size of the window, you need to narrow them. Initially, you need to unfold the canvas, after removing the plugs. Please note that the rolls are equipped with special weights, which must also be removed and cut to fit the new window.

Step by step guide

Use soap and a tape measure to mark the curtain fabric accordingly. Before you cut the roller blinds shaft and bring it to the required length, you need to measure the width of the window, stepping back 2-3 cm from the length of the bracket.

Then you need to install the plugs and cut off the excess part of the rail, which in the end should be equal to the length of the shaft.

The curtains are also marked with soap and tape. With a sharp clerical knife or ordinary household scissors, the curtain fabric is cut to the width of the bottom of the rail.

Then the material is attached to the shaft. To do this, it must be tightly wound, having previously glued a protective tape with a self-adhesive base. The canvas must be wound carefully and adhere to a strictly horizontal position in relation to the shaft. Avoid the slightest distortions, as in this case all the work will be done in vain..

Fold 5 cm of the blade so that a fold is formed where the shaft with the glued tape will be installed. Do not indent too much, as in this case the shaft will slip and will not be able to firmly lock in the desired position..

Then you need to roll it along the top of the curtain and roll it 3/4 of the length. Install the bottom rail into the hole on the shade. Insert the bracket into the very end of the control mechanism, then insert the other end in the same way. Upon completion of the work, all the parts that secure the system must be assembled, and the roller blind, shortened in width, must be hung in the place designated for it..

As you can see, it will not be difficult to cut the roller blinds to the width yourself. Here the main thing is care and diligence, as well as an hour of free time and the availability of the necessary working tools at hand..

Size doesn’t matter

Unlike traditional curtains, they are attached directly to the frame or top slope. The canvas tightly covers the glass, saves from the scorching sun, prying eyes. If desired, the roller blind can be hung over open cabinet shelves, doorway.

Manufacturers offer a variety of models. The format of standard roller blinds – 200×180 cm, large – up to 350×4.5 m.

They are fixed on the upper slope or higher on the wall. Mini cassette long – 2.2 m, and narrow, minimum width 0.7 m.

On the sides they are mounted guides for the canvas. In such structures, the canvas does not sag.

Spring-loaded dormers close automatically.

Fastening the curtain to the shaft

Remove the protective film from the self-adhesive strip of the shaft. The curtain should be wrapped around the shaft and unfolded from the side of the window.

Check which side the control mechanism is located on. The blade must be fixed on the shaft strictly horizontally, otherwise it will unfold at an angle! Fold over 5 cm of the top side of the fabric so that a crease forms.

Place the shaft in the fold with the adhesive strip facing up. Use both hands to roll the shaft towards the top of the blade.

Then roll up the curtain ¾ of its length and insert the bottom rail into the hole on the curtain. The curtain is now ready for installation..

How to trim yourself?

Roller blinds, as a rule, are cut in the event that it is necessary to change the decor of the room or if they do not correspond to the size of the window openings, which often happens when you move and change your place of residence. Any hostess can shorten the rolled canvases.

First, the fabric should be hung on the cornice, after it straightens out and takes its final shape, measurements are taken. In this case, the decorative processing of the product below will depend on the type of fabric.

The easiest way to reduce the fabric is considered to be a double hem, with which you can hide up to 30 cm of fabric without trimming.

In the event that the curtains are sewn from silk or organza, then markings cannot be applied to them, otherwise traces may remain. To prevent this from happening, use universal adhesive strips..

They are pre-ironed with an iron, and then the canvas and the bent piece are fastened. It is necessary to iron the strips through cheesecloth, laying the fabric on a soft towel.

Read more:  Porcelain Tiles For Floor Than Cut

The edges of the roller blinds can also be finished with an edging, which is a fabric tape. It is first fixed with pins, then stuck in. In this case, it is not necessary to shorten the curtains from the bottom, there is a way to reduce the length from the top edge.

Regardless of the type of trimming, for work you will need tailor’s soap, scissors, iron, threads, needles and a measuring tape.

The shortening process itself consists of several stages..

  • The edge is cut first. This should be done carefully, otherwise rushing can lead to deformation and damage to the fabric. Initially, the edges are processed on the sides, then the curtain is bent, well ironed and sewn.
  • Further, a braid is attached to the top of the future curtain, bending the edges of the canvas by 2-3 cm. The ribbon is applied from the seamy side of the product and sewn. The number of seams in this case depends on the width of the tape. The bottom of the roller blind should be double-hemmed..
  • The completion of the work is the drapery..

to the content

How to shorten the length

Most often, adjustment of roller blinds along the length is not required, since it is enough just not to unwind the canvas to its full length. But if you are a perfectionist and it is extremely important for you that the blinds are of the right size, then follow these instructions:

  • Hang the curtains, lower the canvas, wait for it to fully unfold and lie down neatly, then take measurements.
  • Mark where you want to crop the canvas.
  • Remove roller blinds, spread them out on a horizontal surface.
  • Remove the weight from the bottom edge.
  • Cut the fabric.
  • Place a canvas underneath the curtain and sew a “pocket” for the weighting agent, insert it.
  • Hang the curtain on the window.

If the length of the “excess” fabric is not too long, then trimming can be dispensed with. It is enough to make a double fold of the fabric, with which you can hide up to 30 cm of fabric. This option for shortening the roller blind is much easier and faster..

Shortening in width

Often, roller blinds have a large width that does not fit the size of the window. To solve this problem, it is enough to bring the canvas to the unfolded position, for this, plugs are removed from the shafts.

In addition, the rolls are equipped with special weights, they also need to be removed. Then, using a pencil and a ruler, markings are applied to the fabric, and an undercut of excess edges is made with a clerical knife or scissors.

The upper tube is removed so that a small margin of 6-8 cm remains.

As for the weighting agent, it is also cut by a few centimeters. At the end of the work, all fasteners are assembled into a single system, and the canvas is slowly wound onto the shaft. Then the cropped roller blinds can be hung.

How to cut a roller blind with your own hands, see the next video.

Attaching brackets to the ceiling

Determine the center of the window frame and mark this point on the ceiling with a test square. To determine the location of the brackets, set aside the required distance from this point (equal to half the full width of the frame) to the right and left.

How to cut roller blinds to width

It is necessary to reduce the fabric, tube, weighting agent. We lay out the roller shutter on the floor, unfold it, take out the weighting agent, it is well felt.

It is difficult to cut the roller blinds made of organza and other soft fabrics exactly. Instead of marking, a thermolene is glued to the canvas, a cut is made on it.

You can reduce the roller blinds support roller with a hacksaw or jigsaw. The support roller should be 0.8–1 cm wider than the canvas so that the fabric does not deform at the edges when twisted. It remains to cut the weighting material. It is made less than the width of the fabric by a few millimeters..

So, let’s summarize. Roller blinds, blinds can be adjusted to the required size by yourself. All you need to do is arm yourself with a small set of tools. They are in every apartment. Thinking over the interior, you should not give up roller shutters and blinds. They are practical, comfortable, modern.

How to reduce a roller blind or make two of one – on