How to cut a veneered door. Trim the door from the bottom
After I put the laminate flooring, the floor has risen by 2 cm., and one of the doors must be filed at the bottom by 1-1.5 cm.
Interior door, simple laminated covered Fiberboard. Inside the corrugation.
With what would be possible to file the door so that: 1) was flat 2) was not chipped, the effect of “brush” on the cut.
Sawing with what?? Take it to any formatting machine. (a saw for cutting sheet metal) There are in all major construction shops, carpentry factories. Do not even try with a jigsaw or hacksaw. In theory you can do it with a frogman circular saw, but you need very straight hands.
There is a similar experience? I just do not think that the TC will be happy if I bring them the door and said that would have to saw off at 1-1.5 cm. Didn’t saw it in the shopping mall, but sawed off a lot of doors at a friendly factory.
Sawed el.use a jigsaw with a masking tape beforehand. It’s not very pretty, but if you don’t crawl on the floor with a ruler, you won’t notice it. How much was sawn off?? what’s inside at this height?
This is if you cut along the line, and if the jigsaw is lead along the guide bar, it will even out a thin saw, will lead vertically. 16 mm sawed as hard as I tried, the line for the trimmer is straight, but the vertical walks. But the idea with the cutter is a better idea than any other.
No, it won’t. On the plywood “four” will be. On a 40-millimeter doorframe. no.With a circular saw. you’re more likely to make it. Along the guide bar.
At Stroy arsenal. Most likely they’ll cut it, and the price will be ridiculous. I used to bring them 32mm chipboard to saw. They took 35p. per piece. They can charge the same for the door.
Usually the blade is no thicker than 40mm. Exactly as the man who has put another door.
Yes, the blade is 40 mm. Just a door to saw a responsible thing 😀 And the opening foam, casing closed and no jambs are not visible.
If 5 cm bar, and you need to saw 2 cm, then no problem. jigsaw and go ahead (scotch tape from the “beard”). But if you’re afraid to saw more than the width of the bar (will hurt the section with a corrugated tube), it is better to take those who have special equipment!
What’s more, if you cut without a guide bar. vertically the leaf will be less slippery. Because it is possible to press a little to the left and right with the jigsaw and control the blade (not to unroll but to press horizontally)
With a bar the canvas takes much more concrete, up to breakage if you overdo it.
Now you’re making a big deal out of it! These doors can be normally sawed with a hacksaw. и.jigsaw. 😀
After a new carpeting, parquet or laminate may be difficult to open and close the door.This means that the door needs to be trimmed to length. This often happens when you buy a beautiful new door. If the difference in height is not very large, you can solve the problem by removing a little material from the bottom of the door by planing or sanding. But if there is a big difference, it becomes necessary to cut off part of the door.
What you should know before you start work
If you have a hollow door, you can’t cut too much off the bottom. These doors are simply a wood frame with two fiberboards attached to it, and they cannot be cut more than 1 cm; if you have a hard fiberboard or laminated board door, you can remove a little more. There are two types of interior doors: a panel (smooth) door and a slab door. The panel door is fully recessed into the door frame and mounted on hinges. An overlapped door is partially recessed into the door frame, and its edge is on the outside of the door frame. Doors of this type are installed on cylindrical hinges, which allow you to lift the door by removing it from the door frame.
If you want to replace an old door, you must first measure the size of the door opening. You can easily use a carpenter’s ruler for this, which allows you to measure accurately. First you need to measure the height and then the width at the top and bottom of the frame. If there is a difference in width, take the size of the wider part. Add a 2 mm space at the top between the door and the frame. If you are replacing the door, it is best to replace the hinges at the same time.
Removing part of the door leaf: planer, router, saw
Trimming of a veneered interior door is carried out with a planer, router or circular saw. With this tool you can accurately perform the work. The only disadvantage is the possible surface irregularities. If you use a circular saw, then you need to have certain skills. The interior door should be cut with a circular saw with a carbide-toothed blade. If you make a clean cut you will need a disk with a lot of teeth. To perform the work with a hand router, it is necessary to perform all actions with the utmost care. This tool leaves fewer chips.
During the repair sometimes changes the floor level (laying tiles, filling screed or self-leveling coating, etc.) after the installation of floor coverings. п.). Afterwards the interior door must be cut to a certain height to allow the door to move freely when opening and closing it. The same operation has to be done in the case of replacement, if the new door is very large and does not fit into the frame. When installing a new frame, it can also be the case that the size of the opening does not meet the standard of the product.
In what cases is it necessary to do this
If there are difficulties which do not allow the door to open freely. this is an occasion to undercut it. This happens in a number of cases:
- After installation of floor coverings;
- After using a self-levelling coating;
- In the case of deformation (when the wood sagged or swelled).
The above factors are the most common indications for this procedure.
When it is necessary to do it
If there are difficulties that do not allow the door to open freely. this is an occasion to trim it. This happens in a number of cases:
- After installing the floor coverings;
- After the use of self-levelling flooring;
- In the case of deformation (when the wood is sagging or swollen).
The above factors are the most common indications for this procedure.
Do-it-yourself instructions
Before performing the work, remove the canvas from the hinges and prepare it by removing handles and other fittings from it. The door is cut on the workbench, but if it is not available, a large stable table is suitable.
If the solid wood leaf needs to be adjusted to the opening due to sagging or elevation of the floor, it is best to trim the door from below. Take two height measures: at the hinge part and at the door jamb. Transfer the measurements to the leaf, setting aside the new measurements from the top edge. Through 2 points draw a straight line for the trimmer. It is advisable to use a long ruler and an angle grinder to control the right angles between the edges.
Attach the guide rail along the marked line. If using a power tool, it is better to use a metal strip or ruler. If you cut the door with a hand-held wood hacksaw, rails of even slats will do. Use clamps to clamp the template to the saw blade above the marking.
To preserve the varnish and veneer layer on the polished door, finish it with an angle grinder. The tool blade will leave a smooth-edged cut that cannot be made with a saw. Guide the angle grinder along the guide bar. Before machining, tape over the mowing line markings, and transfer the straight line to its surface.
If there is no angle grinder, the lacquer coating on the part to be removed is removed with an emery cloth, and the veneer is cut through with a sharp knife on both planes of the leaf and on its edge parts. Then the door can be sawn off along the guide rail.
Remove the clamps and trim the edges with emery paper. On the veneered door it is necessary to glue the edge banding, matching its shade to the veneer. If the solid bar is painted, the cut should be covered with paint or varnish. Hang the door leaf on the frame, remove warping and attach the removed fittings.
The work is carried out in the same sequence for the replacement of the leaf: the standard dimensions of the new product can be altered in height and width. When carrying out works it is necessary to take into account, what the product is made of.
Make the shortening of the door
The lower part of the door leaf consists of a solid wooden bar, taking into account the possibility of shortening. But usually the width of the bevel is not enough. That’s why we need a bar of 30×30 mm prepared by us., To cover the cavity after shortening. With a hacksaw we prepare a bar that we need for the length, adjust the thickness of the planer, and mount it on the glue.
Cutting the door leaf of a panelled or panel door with glass inserts, it is necessary to remember about the proportions of all its components (correlation of the sizes of all parts and the whole between itself). By radically changing the size of the bottom part of the door we can disturb the harmony of the door. And the door itself and the entire interior will be completely different.
So we have to think about cutting the leaf on both sides, at the top and at the bottom.
In the same way as described above, it is possible to change the size of the door in width.
But I wouldn’t recommend doing this, because with the tool we have, it would be very problematic to cut to 2 meters length, and all the imperfections would be very visible. You’d better do such work with special machines and leave it to professionals.
And we can, if necessary, try to resize the door opening.
In general, we see that it is quite realistic to change the size of the door, if necessary, at home.
How to cut a interior door to width. Trim the door from the bottom
If you decide to install a gas boiler, all requirements must be met in the room. In particular, the gas service will not connect the gas if the room where the boiler is located does not have the necessary minimum clearance between the door and the floor, which provides for natural air circulation.
In fact, it is not as difficult as it seems at first glance. Theoretically, the door can be trimmed without removing the hinges, but this method is not the most convenient.
When cutting horizontally, given also the uncomfortable position of the hands when sawing, the hacksaw will begin to walk on the blade and the cut will not turn out even. So it is best to remove the door, but before you do that, you need to see what kind of gap already exists, as well as whether it is even.
It happens that the door is set flat, and the floor is not quite horizontal, which creates a wedge-shaped gap, and it does not look very nice. So if the gap is uneven, you can solve this problem at the same time. Next, we take a tape measure and mark on each side the required distance from the floor.
Almost any door can be cut. The only exception is a door with glass panels, they can also be cut, but it is much more difficult. If you have a regular door, you will not have any problems.
The hinges that hold the door in the box, there are also different. If the door is old, it will be enough to open the door at 90 degrees and lift it with the crowbar. If the hinges are fixed with self-drilling screws, you need to unscrew them with an electric screwdriver, but before doing so, put wedges under the door, otherwise you could ruin the box.
After you have removed the door from its hinges, you need to create a place where you will saw. The more comfortable you will work, the better will be the result. It is best to put the door horizontally (2 stools will do). Next, we draw a line for a trimmer on the marks you drew.
To trim the interior door is best suited hacksaw for wood, and sharpened. You can, of course, use a jigsaw, but it can start to move, especially if the door is thick enough. You can also use an angle grinder, a drill with a cutting disc, but with insufficient experience is unlikely to work well. A saw is the simplest and most accurate tool. The main thing you should pay attention to, the saw should be kept straight, with a slope to himself (so there were no chips), to cut accurately and clearly on the line.
After the door is cut, we hang it back on the frame and see what we have got.
It happens that the door after installation begins to cling to the side jamb. To fix the situation, you need to adjust the hinges, for example, dokruknut self-tapping screws or put a piece of cardboard under one of the hinges.
If the trim is askew, you can trim with a planer, including electric planer will do. However, it requires a place to work and skill.
How to trim an interior door. video
How to properly trim the door video It would seem, why trim already installed and serviceable door. However, sometimes such a need arises, for example, if the installation of interior doors have already made before, and during the next repair the owner needed to lay laminate flooring, but the doors are not designed for the height. In that case, it is much easier to shorten the door than to replace it with a new design. The question is how to do it correctly and competently.
Any homeowner, when making. Expects that the new design will serve him, as they say, faithfully, for many years. To do this, he chooses reliable and quality doors from trusted manufacturers or orders from professionals and wants to be sure that the repair of interior doors he will not need. In most cases this is the case, but there are situations where you need to trim the door height, for example, if during the next repair the owner wanted to replace the floor covering, and he decided that the laying of laminate or hardwood flooring will be an excellent option. As you know, the laying of parquet and laminate flooring involves a change in the level of the floor, and therefore it is necessary to shorten the door, so she when closing and opening it did not hurt the floor covering. After all, hardly anyone would think to buy and re-install interior doors, involving a large outlay of money.
And here comes the tricky part. Few non-professionals know how to properly trim the door to avoid possible damage and ruined appearance of the construction. Of course, ideally, you should contact professionals who install and repair interior doors, and have the professional knowledge and tools to perform this, not at all simple operation. But if this option does not suit the homeowner or is impossible for some reason, the interior door trim he can also independently. And for this he will need either a hand. or a hand router, available in the arsenal of most home craftsmen, as well as a video instruction on exactly how to trim the door so as not to spoil it.
With a manual circular saw, by the way, you can shorten an interior door, even without taking it off the hinges. To do this, you must first carefully measure the required size of the cut, setting the circular saw disc so that when it passes over an even floor surface and file the door, making an even horizontal kerf across the width of the leaf. To visually see exactly how to trim a door without removing it, see the first video tutorial in this section. This operation is usually carried out before the laminate has been laid on the floor, because otherwise it is much more difficult to trim the door without removing it from the hinges.
In this video you will see how to undercut an interior door without removing it from its hinges
difficult, time-consuming, but also more convenient way to shorten the interior door. to use a hand router. In the second video you can see the whole process in detail. To do this, the door should be removed from the hinges, secured on a flat surface of the table or workbench with the help of clamps, pressing them on top of an evenly exposed wooden bar, which will serve as a guide for the cutter. It is important to set it so that the cutter removes the wood strictly at the distance that is necessary. With the cutter door trimming will take longer than with a circular saw, because you have to make several passes, gradually deepening in the leaf. However, this method of shortening the door is more reliable, especially if the home handyman is not an expert and
How to correctly trim an interior door
If you had to trim the door after installing the hinges, it means that you misdimensioned the box relative to the leaf, or made a mistake with the hinges. In the latter case, it will be more correct to correct the error. Before you place the door on the hinges, make sure that the dimensions of the leaf are shorter than the width of the frame by about 10 mm and narrower by 4-5 mm, and that the lines of the leaf and the door hinges are parallel. At the same time you can make sure that the vertical column of the box on the side of the hinge is perfectly flat. it is very important.
Sometimes the question arises. how to shorten the door after an unintended installation of laminate or parquet. The network is full of descriptions of how dashing installers manage this operation with a coping circular saw. We recommend that you by no means follow this advice. If you can allow such an operation in relation to the door of fiberboard, the veneer of precious wood will most likely be spoiled. The difficulty lies in the fact that even the smallest saw teeth will tear particles of veneer, forming chips and breaks, fix such a marriage is impossible.
Nevertheless, it is possible to trim carefully the height of doors. In Runet it is advised to do this with a powerful hand-held electric cutter and a guide ruler. The method is real, but you swallow a lot of dust, and the figured trim does not always allow you to securely fasten the ruler. It is easier to perform this operation with an electric planer, professional door installation can not do without this tool. In particular, a competent carpenter, using an electric planer, forms on the vertical part of the leaf, facing the hinges, an angle slightly different from 90° and open towards the doorstop. As a result, the hinges in the closed state is also slightly ajar, which removes all the tension between the frame and the leaf.
Before trimming, you should remove the leaf from the hinges and glue on both sides of the bottom of the door with painter’s tape. This is also done when performing the operation with a router. the tape will prevent chipping and protect the varnish from scratches that may occur when in contact with the tool’s platform.
Before you trim the doors with the electric planer, use a pencil to draw a trimmer line on the painter’s tape to guide you. Do not bring the planer to the opposite end, so as not to chip it, remove layer by layer from both sides of the cloth. Try to install the doors on the hinges before reaching the pencil mark. if you cut the excess, you will have to put up with too much lower clearance.
The best solution is to entrust the work to a craftsman from a reputable company. Attention to your problem combined with professional skills will guarantee a successful result.
After laying the laminate, the floor has risen by 2 cm., and one of the doors should be filed at the bottom by 1-1,5 cm.
Trimming the height of the door
Most often, doors are shortened by height. To do this, you must first determine which side is better to do it. the bottom or the top. The decision is taken after careful measurement and taking into account the location of the hinges, which should not be moved.
If the need to change the size of the leaf is caused by an increase in the level of the flooring, then the best option is to trim the door from below. It is carried out in the following order:
- The cut is marked out, using a metal ruler and square. The dimensions are attached to the hinges. A straight line is drawn for the trimmer of the cut.
- Slightly above the traced line guides are installed. They are fastened with screw clamps or masking tape. Metal skids are needed for the power tool, but wooden slats are also suitable for hand tools.
- Using the required cutting tool, a strip of door leaf is cut along the marked line.
- If the edge of the cut is uneven, it is planed with a planer.
- The rails are removed, and the place of cutting is treated with emery paper.
When the trimming is complete, the surface of the leaf is restored. In the case of veneer coating, a strip of veneer, of the appropriate structure and color, is glued to the bottom. PVC glue and an iron are used. Excess is cut off with a knife. Use a brush to restore the lacquer or paint coating.
From the top
This shortening is generally carried out in combination with the lower trimming when it is necessary to maintain pattern symmetry or to trim hollow panels by more than 1 cm. The procedure of cutting itself is almost no different from the previous technology. It is important to make sure that the dimensions of the strip to be cut from below and above are exactly the same.
The difference between trimming from above and below is related to the appearance of the fabric. Any defects in the upper part are more visible, so it is especially important to ensure the evenness of the cut line here. This is accomplished by thoroughly planing and sanding.
We can trim your interior door correctly!
Every person, buying a door, hopes that it will never have to be repaired. For this, many people order doors from professionals to be sure of their quality. But nothing in life is everlasting, and the repair of interior doors. this is an unavoidable action. After you put linoleum or laminate on the floor, the interior door will rub against the floor, scratching the laminate or parquet due to the fact that the height of the floor increased. So you will need to trim the door so that it will open freely, and not catch on the floor. If you leave the solution to this problem for later, you can just simply spoil your new laminate or parquet. And do not forget that the restoration of the flooring will not be cheap, because now no one has extra money.
You want to saw off the door from underneath with your own hands, for this you will need a circular saw. With its help you can shorten the door, even without taking it off the hinges. The first thing you need to do is to make accurate measurements, so as not to cut off unnecessary, then calm down, so that your hand does not shake, and start to act. Remember that the gap between the floor and the door should be more than seven millimeters. In this case, the door will look like a “fusion” and no one from the family and friends will not see any extraneous intervention. Shorten the height of the door also with a hand router. In this case the door will have to be removed from its hinges. Then it will be necessary to put it on a flat surface and well fix it with the help of clamps, having pressed a wooden bar from above, which should be evenly exposed. It will serve as a guide for the router. It must be set so that the cutter will remove the wood exactly the distance as planned. no more, no less.
Let’s cut off an extra 5mm at the bottom of the door with the cutter!
As you have already understood, you won’t have to struggle with the cutter for a long time. Yes, and it will take this process a little more time than the first version of the trimming of the door. You have to make several approaches, gradually going deeper into the leaf. But do not forget that this method is more reliable and you will be easier to avoid irreparable errors. Experiment, try to achieve everything on your own, but do not forget that your actions should be carried out within the limits of reason.
Every professional craftsman knows exactly how to properly reduce the height of the door, because it requires certain skills, and, of course, experience. After all, to damage the door. it is a minute thing, and fix it. it is difficult and lengthy process. Of course, the most ideal option is to contact the professionals by calling 7 967 008 11 18, our masters have the necessary knowledge and tools for this “operation. Today you can get confused by the variety of firms that offer these services, and even more so to understand which of them is the best and most profitable option for you. But do not despair, you just need to know a few rules:
How to avoid sagging doors?
It is best to take measures to prevent this problem, starting from the stage of installation of the interior door.
- It is necessary to pay attention to the right choice of material. Too thin box made of low-quality raw materials with a massive weighty door will certainly lead to sagging soon. When buying, you should carefully inspect all parts for damage, bloating, cracks. They can cause deformation and sagging of the door.
- In winter you should leave the door for a while on a glazed balcony to avoid sudden temperature drops. Otherwise the product can crack and be damaged.
- Saving on fittings, choosing cheap, weak hinges and fasteners is also one of the causes of subsidence. It is better to choose fittings with a safety factor, so it can hold a heavy construction. Possible subsequent decoration of the door with additional elements which will increase its weight is taken into account.
- Often the fault is initially incorrect installation of the door frame and leaf, which led to the warping and sagging doors. If you are not experienced in installing interior blocks, it is better to entrust the matter to professionals. Knowing all the details, the specialist will make the work qualitatively that will affect the service life.
- The product should be operated in accordance with the instructions, avoiding overloading and deliberate wear and tear. Children should not be allowed to hang or ride on the door, to crack nuts with it or in any other way use it contrary to its intended purpose.
- Periodically check the condition of the door hinges, lubricate them.
Interior door sagging is an unavoidable process. In order for this malfunction to occur as late as possible, it is necessary to carry out proper installation of the door unit, choose high-quality materials, fittings. Follow the instructions in operation and do not use them for purposes for which they were not intended.
If sagging does occur, after assessing the causes, you can try to fix the problem on your own. In case of serious faults it is better to apply to a specialized installer of interior doors.
