How to cut the outer corner of a baguette

Varieties of ceiling plinths

The classification of the baguette is carried out according to the material of manufacture:

• Plaster. The most ancient representatives of ceiling plinths. For their casting, special matrices were used. Various solutions were used as an adhesive assembly. The name “fillets” is also used for plaster moldings. In modern construction, they are used very rarely due to the high cost and inconvenience of installation. In addition, more reliable and inexpensive simulations of plaster fillets have appeared..
• Polystyrene (polyurethane). The most common type of skirting board. Products of this type are characterized by low cost, excellent aesthetic characteristics, ease of installation and a rich assortment in terms of external design. The width of polystyrene moldings varies from 5 to 250 mm. They can be used in any type of room, complementing various interior styles.

• Wooden. Expensive and rather bulky baguettes, with the help of which wooden houses with the corresponding interior are mainly made out. To install wooden planks, in addition to glue, screws and nails are often used..
• Plastic. An excellent option for bathrooms and other rooms with high humidity. Installation is carried out on special moisture-resistant glue or secret self-tapping screws.

When installing the above products, you need to know how to cut the ceiling plinth. This does not apply to plastic products that come with special angle adapters..

Using decorative corners

This refers to special corner adapters, which are usually completed with polyurethane and polystyrene friezes. Decorative corners are glued to the very corner, and the baguettes are adjacent to them on both sides. Adjustment in this case is either not required at all, or is carried out with a simple clerical knife..

Ways to get a beautiful angle

The most difficult area when decorating the ceiling surface with a frieze is the corner areas. If you just cut the skirting board at the right angle, ugly gaps will remain. To achieve a snug fit between two adjacent products, you must also trim their edges. There are several ways to do this..

What tool is needed

When installing the ceiling plinth, it must be cut to size or in the corners.

The following tools will usually help you to cut the corner of the skirting board:

• Hacksaw for wood. It is used for working with wooden products.
• Hacksaw for metal. This tool is convenient for cutting plastic, foam and polymer friezes. As a result, it is possible to obtain a fairly clean joint without burrs. When working with saws, it is convenient to use a miter box.
• Stationery knife. It can be used to cut styrofoam baguettes without using special tools. The main thing is that the knife is well sharpened and has a thin and even blade. If you act carefully, the cut is smooth, without any dents..

When using the saw, it is important not to use excessive force, otherwise the skirting board will be crumpled. It is best to practice on some unnecessary piece first. This will allow you to get beautiful fragments in the future..

Other pruning methods

As a rule, in ordinary rooms, the evenness of walls and ceilings is rarely observed. With slight deviations, they can be trimmed during the fitting process. If the deviation of the angle from the standard 90 degrees is large, you need to know how to cut the ceiling plinth without a miter box.

There is only one way out in such a situation – to carry out a procedure on how to cut corners on the baseboards on the ceiling in place:

• To carry out the procedure, how to properly cut the plinth to the ceiling, you need to arm yourself with a finely sharpened pencil (with its help you can apply clear marks that are not visible from afar), a fragment of a baguette, a ruler and a good office knife (if a plastic or wooden plinth is mounted, then a saw).
• Attaching the frieze to the corner, make a pencil mark along the outer edge. Do the same with the reverse side of the corner. As a result, the line should form a cross on the ceiling. The point of intersection of the marks will be the convergence point for the edges of the ceiling frieze. To transfer the scheme of how to properly cut the ceiling plinth at the corners, a frieze is applied and rests with the end part in the corner.
• Next, using a ruler, you need to connect the edges of the frieze and the markings. A simple operation, how to cut a plinth for a ceiling on a solid surface, will not give a positive result: there will still not be a complete connection along the cut of the corner of two separate moldings. In this case, it is necessary to carry out additional trimming in place. This option is suitable for not very wide friezes (up to 5 cm).
• To trim the corner more accurately, you need to put the plinth on the end. When cutting, the knife should move obliquely at an angle of 45 degrees (so that the edge is sharp). After that, fitting in place, if necessary, will be on a very small scale..
• A similar procedure, how to properly cut the plinth on the ceiling, is carried out in relation to the second plank. It must be attached to the place of future installation, resting its butt on the adjoining side of the corner. Next, mark a point with a cross, apply a marking and cut off at the bottom. If adjustment is required, then it is carried out even before spreading with glue..

Similar actions are carried out on the outer corner. It is most convenient to first cut one corner, and adjust the second along it..

How to cut a corner of a ceiling plinth – simple and correct ways

The aesthetic perception of the entire room directly depends on the beauty of the ceiling decoration. This is especially true of the quality of gluing the baguette: if it is not difficult to do this on straight sections of the walls, then when decorating the corner sections, you will need to know how to cut off the ceiling plinths.

How to cut a corner with a miter box

In rooms with even corners and walls, cutting the ceiling plinth using a miter box is usually not very difficult. The tool has the form of a U-shaped groove with saw guides made at an angle of 90 and 45 degrees. Having placed the element requiring cutting inside the device, insert the saw into the guides. During the cutting process, the baguette must be firmly held in place to avoid defects. Cutting off the plinth is quite difficult, since it is necessary to achieve its simultaneous adherence to two planes. If the width of the baguette is small, then it is more convenient to press it to the near side. “How to cut ceiling plinths – cutting tools and rules”.

How to cut off the corner of a ceiling plinth if you are making an outer corner:

• Before cutting the corners of the ceiling plinth with a miter box, it is washed down at an angle of 45 degrees.
• The miter box is exposed in a comfortable position. This will make it possible to determine the exact location of the skirting board: first of all, this concerns the edge of the product that will be adjacent to the ceiling. To avoid confusion, it is best to place the right-side plank on the right and the left-side plank on the left..
• The surface is pressed against the lower surface of the miter box. In this case, the second part rises, turning out to be the closest. It must be applied to the wall of the miter box in such a way that during operation it will not wobble. With this arrangement, the front side of the product turns out to be turned in the opposite direction..
• Cutting must be done at an angle of 45 degrees from yourself. If done correctly, the two halves are folded together to create a beautiful outer corner..

After the correct sawing of the ceiling plinth in the corners is completed, both pieces must first be applied to the ceiling “dry” in order to check the coincidence of the corner geometry. If necessary, trimming is carried out with a knife. It is easier to cover small gaps with a putty, which, after drying, must be treated with sanding paper. As for the inner corner, it is much easier to arrange it..

The procedure for how to cut the ceiling plinth in the corners of the interior type is very similar to the one described above. The first step is to determine the side that will be adjacent to the ceiling. It is placed at the bottom of the miter box. The reverse side leans against the near wall. After sawing off the plinth on the ceiling is finished, the resulting fragments must be applied dry to the corner, checking the quality of the joint. Fitting is carried out if necessary. After that, one and the second skirting boards are installed on the assembly structure. Small gaps in the corner can be filled with a special putty.

Popular materials

How to join a ceiling plinth. Tools for joining the ceiling fillet

Since it is more difficult to arrange the corner joining of the ceiling cornice, you first need to figure out how to join the corners of the ceiling plinth. To do this, prepare the following set of tools: a hacksaw for metal or a stationery knife, a miter box, a protractor, a ruler and a pencil. For trimming the ceiling plinth in non-standard angles (more or less than 90 degrees), a construction knife and replaceable blades are used.

The secret to successful cutting of a ceiling plinth is that it is recommended to cut the plank also from the front side, and not just along the outer edge. If you make the outer corner, then the inner corner. If you want to get joints no worse than venerable repairmen, then tools such as a miter box or an electric miter saw will be useful to you, which allow you to achieve high cutting accuracy..

You can also trim ceiling skirting boards with more economical tools, such as a hand miter box or a hacksaw. A simple saw is cheap, it is extremely simple to work with it, but the disadvantage of such a device is its roughness. There is always a risk of spoiling the material. For example, if you bought poor quality wood or plastic, the product may begin to delaminate or crumble during operation..

A tool called a jigsaw will help to make a burr-free corner on the ceiling plinth. The advantage of this tool, in addition to high efficiency and precision of work. ease of management. You can set the jigsaw to any direction of movement and make the highest quality cuts.

However, there is often no miter box at hand, and right angles are rarely found in our apartments. In this case, you can try to get by only with improvised means. Make a stencil out of thick paper or cardboard that will clearly repeat the inner or outer corner of the wall..

If the plinth is hollow inside, then it is unrealistic to keep it upright when cutting with your hands. you need to build a corner from the available materials, into which you put the baguette, like in a miter box. It’s okay if the corner isn’t perfect. You can even put together two boards. It is important that with their help you can securely hold the molding in one position..

Next, place the corner over the stencil in such a way that the end of the corner is exactly above the corner of the stencil. Place the skirting board in a square and cut it using the stencil guide. Unlike the cutting procedure with a miter box, the blade of a knife or saw can only rest against a corner, so you need to be especially careful and attentive..

To work with foam, it makes no sense to use such a complex technique as a miter box. In this case, you will need an ordinary construction knife. The main thing is to make sure that it has a sharply sharpened blade, then it will be possible to make a high-quality cut without delamination and tears of the material.

How to properly cut a corner on a skirting board. Instructions for installing the corner of the ceiling plinth

How to cut a wide skirting board. Types of ceiling and floor skirting boards, choice of tools

The installation of moldings and skirting boards is no less important stage of the renovation than any other. And trimming the corners is the hardest part here. It is important to choose the right tool for the job and the most suitable cutting method..

How to cut the corners of a skirting board with a miter box. How to cut a corner of a ceiling plinth using a miter box

The miter box is a simple carpentry tool that allows you to cut the workpiece at the desired angle. Most often it is a plastic, wood or metal tray with vertical slots for cutting at an angle of 90 ° and 45 °. There are also more complex miter box designs – for cutting at angles of 90, 60 and 45 degrees. For more professional work, a miter box with a swivel mechanism is used, where the hacksaw can be fixed at any angle to the workpiece.

How to cut a skirting board with a miter box – inner corner:

• We apply the plinth to the ceiling, measure the required length.
• Then we install the plinth strip in the miter box so that the position coincides with the position of the plinth on the ceiling.
• The plinth strip must be pressed against the far wall of the miter box.
• Hold the plinth with your left hand.
• We choose such a position of the hacksaw when the angle is 45 degrees and at the same time the handle of the hacksaw is as close as possible to the left hand.
• We cut the workpiece without making excessive pressure on the saw.
• The next step is to trim the plinth striker. We also install it to the far wall of the miter box..
• Press and hold with your right hand.
• We choose such a position for the hacksaw when the angle is 45 degrees and the handle of the hacksaw approaches the right hand.
• Cut off the skirting board.

Next, we join the trimmed plinths and check the cutting accuracy. For a more accurate orientation, they also say that in order to complete the inner corner, it is necessary to start cutting from the front of the skirting board. After trimming, wooden skirting boards will most likely have to be adjusted with a file..

How to cut a ceiling plinth with a miter box – outside corner:

• In order not to be mistaken with the dimensions, it is better to start by marking the inner corner, and then cut out the outer corner. Otherwise, a situation is possible when the planks may not be enough in length..
• It is necessary to attach the plank to the ceiling and outline the dimensions.
• Install the plinth strip and press it against the nearest wall.
• Hold with your left hand and choose a position for the hacksaw at an angle of 45 degrees, when the handle approaches the left hand.
• Cut off the workpiece.
• We install the striker to the nearest wall, hold it with the right hand.
• We set the hacksaw at a 45 degree angle when the handle approaches the right hand.
• Cut off the workpiece and join the corner.

Trimming the workpiece with a miter box is only suitable if the angle between the walls is even – 90 degrees. If the accuracy is poor, you will have to use other methods..

How to cut the corner of a baguette correctly. Using a laser level

In modern conditions, many home craftsmen already have in their instrumental “arsenal”, which are excellent for checking the straightness of the angle, and marking the baguette when forming both internal and external corners.

How this is done is described step by step in the following instruction table..

Illustration Brief description of the operation to be performed

First, you need to accurately position the laser level itself.. For this, the same distance, for example, 500 mm, is set aside from the corner along the lines of the floor and wall joint. The marked points are connected by a diagonal line. After that, they find and outline its middle. The laser level is installed on the floor, turned on, and then placed so that the vertical plane specified by it (its projection in the form of a line) passes through the middle marked on the diagonal and coincides with the corner of the room. The beam should pass vertically along the mowing line of the corner – this will at the same time show how evenly the corner of the room is formed. In fact, a plane is set that cuts the corner of the room exactly in the center. It is in this plane that the joint of the skirting boards should be located..

In this case, the level should be located so that the projection of this plane is also displayed on the ceiling. You can fix the resulting bisecting line with pencil marks. But even better – do not remove the device, as it will help to more accurately display the desired cutting line and on the plinth attached to the place of future fastening. It is probably clear that the next step is to install one baguette at the installation site. The plank must be resting with the end side against the wall. The beam from the laser builder, passing along the surface of the plinth, and even along all its embossed protrusions, will accurately show the cut line.

After that, along the mowing line of the beam, with the help of a pencil or a thin marker, the cutting line is outlined..

Using a knife, a corner is cut along the intended mowing line – in this case it is impossible to make a mistake. Then, in the same way, the mowing line of the cut is marked and the second plinth is cut..

Now that both parts for forming the corner are ready, they need to be connected to each other at the place of future fixing.. If the joint is neat, then you can mount the baguette with glue. If a small gap has formed between the planks, then the ends of the plinth must be corrected with a knife.

When installing the ceiling plinth, the strips that form the corner are first glued, and the flat trims are fixed last..

If, when carrying out the approximate alignment of the corner side of the baguette, its other end will find on the already fixed segment of the plinth, you should immediately mark the required length in order to cut off its excess. In this case, the straight edge is trimmed just at right angles..

To correctly cut the baguette for the outer corner, it is also necessary to start marking from the floor using a laser level.. There is a slight difference in the primary build here. At first, mowing lines are simply drawn along the ruler, which are a continuation of the walls. Then an equal distance is laid on them from the corner, these points are connected by a diagonal, on which the center is determined. The beam is directed through this mark to the protruding angle, also with the projection of this plane on the surface of the ceiling.

Further, segments of the baguette are alternately applied to the wall and the protruding corner so that the beam passes through them. Marking is carried out along the mowing line of the projection, and then the end part of the skirting board is cut. After that, it is necessary to try on both segments at the installation site, aligning the sections. If necessary, the ends of the strips are adjusted. If everything is fine, proceed to fixing the fillets on the surface..

Ceiling plinth

A ceiling molding, aka molding, fillet, curb or just a plinth, is most often used to finish the joint between the wall and the ceiling. Although sometimes it is used to cover internal corners, make decorative frames or panels, decorate niches and architectural elements. There are several of the most popular materials for making ceiling moldings:

Plastic (polyvinyl chloride). It is more convenient to cut wide and rigid moldings with a hacksaw for metal. If you need a more gentle tool, use a jigsaw..

Foam (expanded polystyrene). A very lightweight and porous material that is best cut with a sharp utility or utility knife.

Wooden baguettes. Suitable for cutting are helical saws specially designed for baguettes. You can also use hand or jigsaws.

How to make an inner corner of a ceiling plinth

An internal angle is one that is not more than 180 degrees. These are the ones that most often have to be cut. Trimming the edges of the baguette is carried out, as a rule, with a miter box, but you can do without it..

If this happens with its help, then before docking it is necessary to take into account that the element that touches the side of the tool when cutting off is glued to the wall of the room, and the one that touches the lower part is attached to its ceiling.

It is recommended to measure the angle between the walls of the room, and if it turns out to be straight, then the dumbbell is cut at an angle of 45 degrees. To make an undercut, for a start, the desired element is installed in the miter box. Then the edges are cut.

If the walls turned out to be crooked, then the best option is to cut the plinth yourself, you will need a ruler and a clerical knife. To do this, attach two different parts to the wall and mark the place of the cut with a pencil, after which they carefully cut.

To control the accuracy of the work done, the product is first tried on the wall, and only if it is cut off without any errors is it fixed, and if you nevertheless noticed irregularities, then it is very easy to correct them with a clerical knife and only then mount it.

Usually, if the corners of the room are even, then no problems should arise with them, but if not, then minor flaws are always eliminated, the main thing is to try hard.

Simple secrets of a successful baguette installation

When cutting, you should not make much effort, since the foam will crumble, and the wood. split.

Dumbbell elements are usually tried on to the wall, and if there are no gaps, and everything fits snugly, then the work is done correctly.

After the plinth is fixed in the corners, it is recommended to fix all subsequent parts, but before that they are processed at the junction with sandpaper. It must be remembered that the docking of each should be without cracks and irregularities..

For those who do not want to do difficult work, but are also not ready to give up the decorative element of the apartment, it is possible to use a special component that closes the joint. Looks very original and saves time and effort.

For a complete picture of the process of joining a ceiling molding, watch the video with a detailed description of the steps.

How to join the corners of the skirting board

Installing a skirting board may seem like an easy task, but it is extremely difficult and requires a lot of care. In the process, beginners are faced with numerous problems, the most common among them is the docking and cutting of dumbbells..

Performing the work, we prepare the following tools for cutting and joining:

• a clerical knife or a knife for metal (depending on the material from which the plinth is made);
• goniometer;
• ruler;
• pencil;
• miter box.

It is designed for cutting dumbbells at perfectly even angles, and if they are not such or the tool is not available for some reason, the element will need to be trimmed manually. To determine whether we need it or not, it is recommended to use a protractor. If they turned out to be curves, then before installing the baguette, they must be leveled with plaster or drywall.

The hardest part of joining is cutting. The slightest mistake leads to a waste of materials. Dumbbells are attached to the ceiling differently from the usual ones, but a little differently. It should be remembered that they are cut off not only from the front side, but also along the outer edge. The simplest material to work with is foam. It is easy to cut and not so fragile compared to other materials, so it is much easier to work with it..

How to cut a baguette with miter box

To cut the baguette using a miter box, we fix it in the tray as it will be attached to the ceiling. Cut it off along the guide groove. If it is wooden, then we cut it with an ordinary hacksaw. There is also a hacksaw for metal, and to cut off expanded polystyrene or polystyrene, we will use a simple stationery knife, but it must be very sharp so as not to damage anything.

How to join the corners of the ceiling plinth: photo and video instructions

The ceiling plinth mainly performs decorative functions, it allows you to hide all repair errors. It is attached after pasting the wallpaper at the junction of the walls and ceiling. A well-chosen skirting board can visually expand a room. It all depends on the chosen model and size. Now on the construction market you can find a huge variety of ceiling skirting boards. Currently, they are made from polystyrene, polystyrene, polyurethane, gypsum, polyvinyl chloride, which is the most economical option, and are also made from various types of wood. Wooden skirting boards look much more aristocratic than the others, but they are also harder to work with. In any case, the choice will mainly depend on the style of the room. Ceiling skirting boards are also called a frieze, baguette or dumbbell.

How to cut a baguette without a miter box

If there is no miter box in the house, then its analogue is made with one’s own hand. Alternatively, they draw on a simple album sheet. To do this, on paper, draw two mowing lines with marks of a certain degree. You can put them off using a regular school protractor. They use a miter box of their own production in the same way as a purchased one. You just need to put the product correctly and cut off the excess part.

It is also really possible to make it with your own hands from three boards, making slots there, which can be marked with a student’s square or the same protractor.

How to make the outer corner of a ceiling plinth

Inside corners are much more common than outside corners. Usually they are at least 180 degrees. Despite this, it is not at all difficult to dock them..

To correctly cut the baguette, the first thing to do is draw a mark on it, for this we attach it to the ceiling and mark with a pencil the place where the cut is planned to be.

Then we put the product in the miter box at an angle of 45 degrees. When it is already placed there, it is carefully trimmed. It should be remembered that if that part of the dumbbell, which is more located on the left side, then we cut it off according to the left designation, in the same way as the inner corner. Next, we cut off according to the same plan and the right.

When the ceiling frieze has already been cut, make sure it is done without any errors. To do this, fold the two pieces together and only if they fit perfectly can they be attached to the wall..

When cutting, the frieze should be kept straight, since with a curved trimming, gaps appear when joining and for the same reason it needs to be cut with only a sharp blade..

How to make your own corners on skirting boards without using a miter box

The most relevant method of cutting off the corners of dumbbells is the use of slusl, but it is used only if the room is perfectly flat. If the room is more than 20 years old, then it is not like that. Therefore, if you use it in such a situation and cut off the dumbbell at an angle of 45 degrees, a gap is formed, and in the future it is almost impossible to hide it. Cutting off the product without using it is possible using available means. So, for work you will need:

• pencil;
• ruler;
• sharpened knife or jigsaw.

To trim the baguette bar without using special tools, you will need to follow several steps.

It is necessary to take one part of the plank and attach it to the wall in exactly the same way as it will look in finished form.

With a pencil, draw a fishing line along the dumbbell itself and remove it.

Crostini Bar 2/5 – Preparing the Baguette – Honeysuckle

We attach the second part of the frieze to the drawn mowing line in the place where it adjoins the first.

Now you need to draw the line with a pencil in the same way as in the first case..

Where the element of the baguette will be attached, the markup should turn out.

You need to lean one of the two skirting boards against the markings again, and transfer the point of contact of the two straight lines to it. This line is on the bar and will be the place to cut. Exactly the same should be done with the second.

How to shape a baguette

When the cut lines are marked, they must be cut. It is recommended to cut with a jigsaw, it is easy to operate and has high precision in work.

Ready cut baguettes can be attached to the wall.

In order for the attached bar to look perfect, it is recommended to practice, for a start, on small pieces, and only after that do the final installation.

Now that the work on the installation of the ceiling plinths has been completed, you can proceed to further processing, namely, to paint them..

Ceiling skirting board, how to cut corners. Using a miter box

Floor plinth

A modern skirting board is hardly a gap bridging strip. It is a constructive component that complements the design and enhances the overall look. Skirting boards are made from several materials:

Wooden ones can be made from solid wood or veneer. For trimming, use flat or circular saws, jigsaws.

Plastic skirting boards are dangerous competitors to traditional wood. Easy to install and cut with an ordinary hacksaw for metal.

Aluminum skirting boards are the latest in interior design. Cut usually with a saw or hand saw for metal.

Only on wooden skirting boards will you have to make a corner trim. The rest are cut evenly and connected using special corners.

Popular materials

Ceiling plinth

A ceiling molding, aka molding, fillet, curb or just a plinth, is most often used to finish the joint between the wall and the ceiling. Although sometimes it is used to cover internal corners, make decorative frames or panels, decorate niches and architectural elements. There are several of the most popular materials for making ceiling moldings:

Plastic (polyvinyl chloride). It is more convenient to cut wide and rigid moldings with a hacksaw for metal. If you need a more gentle tool, use a jigsaw..

Foam (expanded polystyrene). A very lightweight and porous material that is best cut with a sharp utility or utility knife.

Wooden baguettes. Suitable for cutting are helical saws specially designed for baguettes. You can also use hand or jigsaws.

Ceiling skirting board, how to cut corners. Using a miter box

The tool allows you to cut the corners of the molding, located on the outside or inside. The swivel mechanism will help to form parts with a bend of 90 or 45 degrees.

Outside corner

To cut baguettes to the outer corner, wind them into the miter box from different sides and press them against the wall farthest from you. Make a cut in two different cuts of the fixture at an angle of 45 °.

Fixing prepared skirting boards in place with glue

The technology of fixing the plinth strips has already been discussed in detail earlier in the articles “How to glue a foam plinth” and “Plinth for a stretch ceiling”. Let us recall the main provisions:

• glue must be applied not only to the reverse side of the fillet, but also to butt cuts;
• rivers must be kept pressed until the glue sets;
• the curing time of the adhesive composition by the manufacturer of the material is indicated on the package;
• after fixing the plinth, all places of loose fit should be sealed with putty or sealant;
• in the case of a stretch ceiling, the side adjacent to it is not smeared with glue, and fixing is carried out only on the wall.

Your task is to make the joint monolithic, without gaps and cracks. Therefore, the issue of pre-fitting is the basis of success..