How to drill through concrete without a hammer

How to drill a hole in concrete without a peorator

When preparing to renovate the house, you need to be prepared for the fact that you will have to drill into the walls. For example, to fix the profile for drywall sheets.

At this stage, there are usually some difficulties, since in many homes the walls are made of concrete. In addition to high strength, the material can be combined with rebar, which doubles the difficulty.

To drill a concrete wall with an ordinary drill, you need to become familiar with all the nuances of the working process in advance.

General tips

Drilling through loadbearing walls and concrete partitions is no easy task. To perform the intended work quickly and efficiently, you need to know some secrets and tricks. It also does not hurt to listen to the advice of experienced craftsmen:

• Use a concrete drill bit to work with the same material, as well as stone and ceramic. For metal and wood, they are categorically not suitable.
• Drill steel reinforcement encountered in the wall only with a metal drill bit, then change it back to a concrete drill bit.
• Break up hard stones in the concrete by hand with a sledgehammer or use an old drill bit.
• Keep an eye on the nozzle when working with hard concrete. It must not overheat, so take breaks every 10 minutes.
• To maintain the integrity of the wall on the back side, you need to slow down occasionally.
• You can drill ceramic tiles with a concrete drill bit, but do not press down hard on the drill to avoid cracking the finishing material.

By following these recommendations, you can drill a hole in a concrete wall without too much trouble. That way you can save not only time but also your own strength.

How to choose a tool

Peorator is most often used for concrete drilling. It has several advantages over an ordinary drill.

• Increased power;
• the function of chiseling with different types of chisels;
• Drilling large (in diameter) holes;
• The ability to penetrate particularly hard materials.

Despite the listed advantages, this tool is not always suitable for work. In some situations, its use is simply impractical.

Peorator is not suitable in the following cases:

• When you need shallow holes in the wall (10-12 mm);
• when working with foam block (otherwise the material will crumble);
• When the required number of holes does not exceed 15.

Based on this, we can conclude that for home use, an ordinary drill is more suitable. To buy such a tool for drilling walls, it is necessary to consider a number of important points.

The drill must meet the following requirements:

• It should be percussive, because this type is most effective when drilling concrete walls. In a hammerless drill, the nozzles and chuck will fail too quickly.
• It’s better to buy pobedite nozzles, designed for concrete work. And the tip. with a coating of durable alloys.

It is also possible to choose a drill-powered tool. True, such a tool is more expensive than a conventional model. But it has extra power, which you can adjust as you wish.

How to drill a concrete wall with an ordinary drill without a hammer drill

Concrete is a very dense material with gravel inclusions of different sizes. This is the peculiarity of drilling concrete surfaces. Additionally, the wall is reinforced with rebar, which also makes drilling difficult. Peorator, due to high motor power, is used for manipulation with strong materials, but it can not be used for drilling foam blocks, because they begin to crumble. It is difficult to make small holes (less than 10 mm) with such a tool. The apparatus may overheat if operated for a long period of time.

The torch can be easily replaced with other tools if necessary. This is possible if the amount of work is small. Otherwise the devices could become defective. Power screwdrivers, diamond core drilling machines, regular drills, or products with an impact mechanism are often used as substitutes.

If a large number of holes is expected, then the choice is made in favor of the latter tools. A standard drill quickly breaks the chuck when subjected to high loads. When starting a repair, you can consult specialists on how to drill a concrete wall with an ordinary drill.

Can it be done

With proper use of the tool and drills, compliance with the manufacturer’s instructions and the recommendations of professional builders, with an ordinary drill drill drill holes in concrete, brick and stone partitions. As a result of manipulation should get an even hole. The working surface must not be damaged.

Conventional nozzles are not suitable for this type of work, they must be made of high-strength materials (diamond spraying, victor).

How to drill a concrete wall with an ordinary drill without a torch

Concrete is a very dense material with inclusions of gravel of different sizes. This is a peculiarity of drilling on concrete surfaces. In addition, the wall is reinforced with rebar, which also makes drilling difficult. The torch, due to its high motor power, is used for manipulation with strong materials, but it cannot be used to drill into foam blocks, because they begin to crumble. It is difficult to make small holes (less than 10 mm) with this tool. The machine can overheat during prolonged use.

If necessary, the torch can be easily replaced with other tools. This is possible if the amount of work is small. Otherwise the machines can break down. As a substitute, they often use screwdrivers of increased power, machines used for diamond drilling, ordinary drills or products with an impact mechanism.

If a large number of holes is expected, the choice is made in favor of the latter tools. An ordinary drill quickly breaks the chuck in case of heavy loads. Beginning repairs, you can consult specialists how to drill a concrete wall with an ordinary drill.

Can it be done

If the tool and drills are used properly, the manufacturer’s instructions and professional builders’ recommendations are followed, an ordinary drill can be used to drill holes in concrete, brick and masonry partitions. As a result of manipulation should get a flat hole. The working surface must remain undamaged.

Ordinary nozzles are not suitable for such actions, they should be made of high-strength materials (diamond coating, victor).

Drilling through concrete WITHOUT a torch

In December the stars aligned: I had an urgent need to hang a couple of showcases for medals and orders on the wall.

I had an urge to hang a showcase for medals on the wall. It’s made of Karagach wood, A4 size, weighs about 1200g. Author’s photo

I was too lazy to take out the torch. I remembered the magic ceramic feather drill. “If I drilled a granite pebble with it at my country house, I can certainly drill a hole through a wall. At the same time. to test the new electric screwdriver,” I thought.

A 5mm ceramic and glass feather drill bit from Leroy Merlin. Photo by the author

Drilled eight holes in half an hour! Oh, sorry, the holes. I burned the drill bit, because I worked at maximum rpm (1350 rpm) and forgot to wet it. Nevertheless, one 20 mm deep hole took me no more than two minutes. It turns out, it takes longer to mark than to drill. I could not help but be pleased that I worked not only faster, but also much quieter than my neighbor.

I drilled a hole in a concrete wall in about 2 minutes. The drill bit gets very hot at the second speed. it needs to be wetted. Photo by the author

Well, I should have “drilled” the concrete on the first speed (at 300 rpm) and moistened the drill bit more often.

I used a 6mm wood plug instead of the dowel rod. Length. 20 mm, the hole in the plug drilled in advance. Photo by the author

Hammered a plug into the hole.

The 6 mm plug fits into the 5 mm hole tightly and far apart. Photo by the author

The showcase for medals weighs from 1 kg to 2 kg. The 2.5 mm screw holds this load very well.

Screw a screw into the cork. Photo by the author

Now you can solemnly hang it on the wall.

The showcase with the precious brooches looks better on the wall than the painting. Photo by the author

Choice of drill

The decisive step is the choice of drill bit, because the quality and integrity of the nozzle depends on it. In construction stores there is a wide range of drills that are suitable for a certain type of material.

Concrete drill bits have a triangular shaped tip and are made of carbide compound. Experienced repairmen recommend using a pobedite drill bit because it does not tear the material.

If the drill stuck, you will need to use a puncher. Having set the device in the hole, it is necessary to hit it with a hammer several times to soften the impassable area.

Also, many people who carry out minor repairs are interested in the question of whether an impact drill can drill concrete. So, if there are difficulties at the drilling stage, the holes can be drilled with an impact mode or a peorator. However, the latter has a significant disadvantage. it forms a hole with a diameter of at least 13 mm.

To perform multiple holes, tips are used on the nozzle:

• Pobeditovat tip;
• Universal drills. they need to be cooled regularly;
• diamond drill bits are expensive, but they can last for years.

During the work, it is important to make sure that no sound of contact with metal is formed. If the drill hit a block of reinforced concrete, you need to complete the procedure before the nozzle dulls.

Properly drill a wall of concrete with rebar can be drilled in several steps:

If you can’t drill a hole in the concrete with an ordinary drill, you need a torch

Can an ordinary drill drill through concrete?

This can be a drill or a torch. A drill can also be sufficient if you only need to make a few holes and the torch is not handy. However, when working with concrete with this tool, it is important to remember that in this case it is necessary to use pobedite drill bit with a tip that is coated with carbide.

The piezoelectric drill is designed for drilling concrete, but in its absence, in many cases, the electric hand drill can do the job. Succeed with the right drill bit or core bit.

What to drill concrete without impact?

Our modern housing is increasingly built of monolithic reinforced concrete slabs, which have increased strength. In the arrangement of such houses, drilling concrete walls causes certain difficulties, and almost every home master has encountered them, probably abandoning this venture. In this lesson we will answer the following questions in detail, namely: how to drill a concrete wall correctly, how to prepare the surface for drilling and what tools and devices are needed for this.

Preparing to drill a wall

Before you start drilling a concrete wall, you need to make sure that there are no water pipes or steam heating pipes nearby. You can check this with a metal detector. This is a special device that reacts to such types of metal as: iron, steel, and non-ferrous metals. This tool will also help locate conductive electrical cables near the drill.

Since the concrete wall is a monolith of metal rods and crushed rock, bonded together by sand and cement, then to drill holes you will need special drills from hard alloys. Pobedite drills or universal drills that have a diamond coating are good for this purpose. If you find a rebar in the wall is drilled with a drill bit on metal.

How to drill a concrete wall with a drill bit

Usually, the drill for drilling holes in the wall of concrete is used if they need to drill 2-3 pieces of small diameter, for example, to hang a picture, a small cabinet or a shelf.

If the drill is without percussion function, then in addition to pobeditovogo drill another hammer and a metal pin (puncher), matching the diameter of the hole.

As the drill sinks into the concrete wall from time to time you need to insert the drill bit into the hole and hitting it with a hammer to punch too tight areas, not forgetting to twist it a little. After breaking up a tight area with a puncher the process of drilling a concrete wall with a drill can be continued further, until you get a hole of the desired depth.

This rather time-consuming process can be made much easier and faster if you use a percussion drill when drilling holes, but it is better to use a peorator for such work.

How to drill a concrete wall with a hammer drill

Since the main purpose of the peorator is percussive work in solid materials, using it when drilling into a concrete wall is just right. With the help of an electropneumatic mechanism, the rotary drill makes reciprocating percussive movements and creates deep and accurate holes. The drill differs from the impact drill in that its main principle is not drilling, and the impact. Thus, the process of how to drill a concrete wall with a peorator is much faster and of higher quality.

Before you start drilling a wall of concrete mark with a pencil the place of the intended hole and pick up the drill of the required diameter. Next, you make a small hole with a puncher or set the tool in “drilling only” mode. After that, you set the “drilling with impact” mode on the drill to the required depth. Remove the auger when the work is finished. It is also desirable to remove concrete dust from the hole with a vacuum cleaner.

Useful tips when drilling a concrete wall

To drill a concrete wall quickly and efficiently, you can use the following tips:

• Drill is used when you need to drill a few shallow holes with a diameter of up to 13 mm, for deeper and wider. is used peorator or special equipment;
• When drilling holes for plastic dowels, make the depth of the hole 8-10 mm longer than the length of the dowel, t.к. After drilling, dust remains in the hole from the crushed material;
• to make sure the drilling is accurate and the drill does not jump around, set the equipment to “drilling” mode before you start, without allowing the drill to rotate too fast. Then, as a small hole will be obtained, you can add speed and switch the tool already in percussion mode;
• so that the drill does not break from overheating, it is necessary to wet it with cold water;
• Always wear eye protection when drilling to avoid getting chips in your eyes;
• You can pick up the dust with a vacuum cleaner and keep it next to the hole while drilling.

Now you know how to drill a concrete wall, so that the holes were deep and neat. The following video will show you how to drill through a concrete wall with a twist drill.

How to drill in concrete. basic approaches

During repair and construction work it is necessary to make a hole in a concrete wall, which will not cause problems if you have a professional set of tools. But it is not always possible to have a peorator and a carbide drill at hand. This means that you have to go to the store and spend a lot of money. But if you need to make one small hole, it is enough to apply wit and use the existing experience of home masters.

When you have everything you need

In order to drill a concrete wall, you need a drill and a drill bit, without them it is impossible to perform this work. If there is a peorator, however, the procedure will not take more than a couple of minutes:

• to secure the drill bit;
• if it is important, to put the nozzle-restrictor;
• To outline the hole with a construction pencil;
• In the presence of a puncher, it is desirable to make a notch;
• start drilling.

During operation, it is recommended to smoothly increase the speed, so as not to expose the tool to excessive strain. Yes, in addition, if you rotate quickly on the start, the cutting edge will begin to shift, which can lead to misalignment.

Approximately the same sequence of actions is performed in the presence of an impact drill. Although there is some limitation here. Its power is not always enough to make a hole with a diameter of more than 8 mm, even if the manufacturer says otherwise. In this case, it is recommended to divide the work into two parts. First of all you have to use a drill bit with a smaller diameter. 4-6mm. And then widen the hole to the right size.

How to drill through brick without a peorator

It would be better if you had several different sized stone drills on hand. you start. A regular drill is not as powerful as a peorator when penetrating concrete. For this reason, you would have to start with smaller stone drills as you move up.

After you’ve assembled a few quality masonry bits of various sizes, go ahead and mark the holes you want to drill in.There are three things you need to keep in mind: the position of the hole, the size of the hole and the depth of the hole to be drilled.

For accuracy, it is best to use a tape measure and a pencil or marker to mark on the brick the place you are going to drill. You need to measure and mark the hole locations depending on what you want to use the hole for.

To double check the location of the holes, hold the rack, artwork, TV mounting brackets, or other templates directly over the marks.By doing so, you will realize how accurate you are with your holes.

Of course, your safety comes first when drilling in brick with any power tool. Before you start, wear leather gloves, safety glasses, N95 respirator and hearing protection.

Dust from bricks and mortar contains an airborne component known as crystalline silica. It can be dangerous to your health, even if you inhale a small amount of it.

The N95 respirator is useful for drilling and cleaning, as it filters up to 95% of particles in the air. These particles in the air can cause serious lung problems, such as lung scarring.

Also, if your job involves the use of a ladder, choose a ladder with strong steps and make sure the legs rest on a firm surface. Then be sure to get into a position where you can apply considerable force to the tool while maintaining high stability.

Position the pilot drill perpendicular to the brick wall and set the drill to low speed, holding it with both hands.Hold the pistol grip with one hand and the auxiliary grip with the other.

Make sure that the drill is positioned straight and exactly perpendicular to the wall. Drilling at an angle can cause alignment problems during insertion, which can greatly affect the holding capacity of the hole.

Start drilling the brick slowly, without pushing too hard, so that the drill can do its job. We recommend using a smaller size masonry drill bit with a sharper end to start with to penetrate the concrete.

A slow start is important because it prevents the drill from overheating, which can make it dull or blunt. If your drill has a single-speed drill, it is recommended that you drill in short bursts to avoid overheating.

A regular drill bit is not designed for drilling in concrete. Drilling will generate a lot of heat due to the process of friction rotating around the brick material.This means that without the impact action of the drill bit, the stone or concrete drill bit will become too hot and too fast.

Excessive friction and heat can eventually damage the drill bit. Thus, you need to protect your rock drill bit from any possibility of damage so that it will last longer and be more durable.

Regularly refill the drill pad with water or grease. Apply it to both the hole and the drill bit to keep the device from overheating. Also, be sure to immediately apply water to the drill bit if its motor begins to splash.

After creating a starter or pilot hole in a brick wall, it’s time to move on to larger stone drills. Wipe the drills with swabs and position the drill perpendicular to the pilot hole created in the previous step.

Make sure the drill bit is level and perpendicular to the wall so that you don’t have any alignment issues later on when installing. If necessary, slowly and gradually increase the size of the masonry drill bits to increase the size of the hole.Use these larger bits to re-drill the hole.

How you are going to use the hole makes a big difference, even if you keep switching to larger masonry bits. If you are going to drive a bolt into the brick to hold something in place, consider the weight of that object because the length and size of the hole depends on that.

Also, the bolt you are going to install will determine the size and depth of the drill. In general, start with a smaller drill bit and gradually work your way up until you get the perfect result.This will also make your task easier and faster.

At some point your masonry bits may stop going deeper or even get stuck before you reach the desired depth. In this case, you must first break up any blockages (such as stones in the concrete) by smashing them with a nail and hammer.

Then grasp the handle of the drill firmly with both hands and stand firmly up.Make sure your feet are steady on the ground and slightly apart to hold the objects steady should the tool produce a kick.

With the index finger of your dominant hand, press the trigger on the innermost segment of the drill. Then simultaneously apply constant pressure to the brick with the drill bit.

This process requires that you use all of your body strength to push the rock drill bit into the brick as deep as possible.Nevertheless, never apply excessive force to the drill bit, otherwise you might break the tool.

When drilling brick without a peorator, it is very important to regularly lift the stone drill bit out of the hole.

You can do this by increasing the speed slightly and moving the drill straight forward and backward to remove excess dust and debris from the hole.

By holding the drill bit in rotation and lifting the drill back and forth, you practically remove excess dust and other materials from the hole, preventing the drill bit grooves from clogging.

Removing excess dust and debris from the hole not only cleans the grooves, but also allows the stone drill to work more efficiently and create minimal friction.

After drilling the hole or holes in the brick, it’s time to insert anchors into the wall that can support the weight of the object.Make sure the wall hanger or exterior mount is properly secured with secure screws that guarantee durability.

Tips from the experts

In order for you to be able to drill a concrete wall properly, you need to have the necessary equipment, do all the work carefully and adhere to the following recommendations:

• without peorator work can be done with a percussion drill or drill with an electric screwdriver;
• do not buy cheap drills, as they very quickly fall off the pobedite tip, and they fail;
• instead of a puncher, you can use a pobedite tool, one you will break the rubble, and the second, inserted into an ordinary electric drill, drill;
• For working with concrete, the drill must have an SDS-plus chuck;
• Take into account the location of the fittings to determine where they are, you can use a metal detector, if the fittings are bare, it must be painted to prevent rusting;
• to work with concrete, you can use universal drills with diamond coating, but they must be inserted only in a regular drill, or it is necessary to turn off the percussion mode.