How to light a gas water heater: ignition methods
Many consumers are sure that the use of gas water heaters at home is life-threatening, as a gas leak can occur or the column can explode. Previously, old-style speakers were installed in houses, which could fail if the owners ignored the precautions when using them. Modern gas water heaters. This is a new kind of devices with automatic protection.
You should NOT use outdated models of gas water heaters. They need an extremely careful and careful approach, which will make its use extremely inconvenient. In order to light up the old-style column, you must use manual ignition. Modern devices in most cases turn on and work automatically.
Ways to turn on the units:
- Manual ignition. It is mainly suitable for igniting older models. Earlier to light up the column. It was necessary to use matches to light the Wick. First, it was necessary to open the water supply system, such as the connections to the column. Then the main valve was opened, and then the afterbirth after the gas was supplied to the ignition wick. The ignition wick continued to burn even in the absence of water pressure. It was necessary to turn off the column manually. At home, the use of this type of speakers is undesirable.
- Piezo ignition. Many types of columns have this element installed. When the button is pressed, the wick ignites in the combustion chamber. The ignition wick ignites due to the mechanical force causing a spark. To turn on the main burner, it is necessary to bring the main regulator into operation, which supplies gas.
- Automation. Modern modifications involve automatically dusting the wick and the main burner. According to the turbine, it turns on due to the water pressure. The only problem with the operation of such a column may be insufficient water pressure.
When installing modern speakers, you can be sure that they are safe to use. In order to use them, special knowledge and skills are not required. But if the column breaks down, you need to contact the gas service directly. It is strictly forbidden to repair the speakers yourself.
A simple way to ignite: how to turn on a Bosch gas water heater
If the installation was carried out independently, or the wizards for some reason did not launch, then the instructions for action can be read further. To do this, you first need to open the taps through which water and gas are supplied. Then you should hold down the slider, which regulates the power: it is located on the front panel.
How to light up a Bosch speaker:
- Move the regulator to the right if it is in the Turned off.
- The regulator should go to position piezo ignition. This means the spark icon and vertical buttons will connect.
- The start button follows drown finger, while pressing the piezo power button. The fact that the piezoelectric element has worked will be notified by characteristic clicks.
- Important Make sure that the flame does NOT go out for the first ten seconds. Then you can transfer the power to the Desired level.
After the power is transferred to the desired one, the flame is constantly burning in the mode that was set. But when you turn on hot water, the column starts automatically heating the water. Turning off the column is easy. You need to move the slider all the way.
Ignition features: how to turn on the column Ariston
The gas water heater refers to a typical analogue of a water heater. The water is instantly heated using an instantaneous water heater. The column allows you to use hot water all the time.
It is very simple to ignite the Ariston column, since it can have piezo and electronic ignition, which suggests that the user just needs to open the tap. The device only needs to be turned on after installation. After that, the column will work smoothly.
Features of Ariston columns:
- Compactness;
- Stylish and compact design;
- Available in different colors;
- Automated.
Interestingly, many modern gas water heaters can run on batteries. When choosing a column, you need to pay attention to the methods of its ignition and installation options. In any case, for safety reasons, the old gas water heater should be replaced with a new and modern one.
Open type: how to start a gas water heater
Flowing gas water heaters installed in residential premises cause a lot of controversy. It should be noted that modern gas water heaters are not dangerous if you follow all the rules for their use. The rules for handling the column should be known to everyone who lives in an apartment or house and uses such a column to heat water.
If there is a large accumulation of gas in the room, it is necessary to open the windows in order to lower the gas concentration. It is important to know that in the presence of gas in the room, it is strictly forbidden to turn on electrical appliances and fire. If the column is malfunctioning, call the gas service.
How to light up an open column:
- It is strictly forbidden to ignite the column if there is no reverse draft in the chimney.
- Do not turn on the device, and do not understand the instructions.
- It is important that the room is equipped with a constant flow of air.
- You cannot independently repair or make changes to the operation of the gas water heater.
When firing up, do not touch the front of the panel. When turning on the column, it is better to set it to low power. It should be noted that modern speaker models are equipped with safety devices that stop the operation of the speaker if the thrust comments.
Instructions: how to turn on the gas water heater
How to turn on the gas water heater BOSCH?
2016-10-28 Evgeny Fomenko
Let us consider how to light a bosch gas water heater using the example of models of gas flowing water heaters Bosch WR10.B, WR13.B, WR15.B manufactured in Germany, for the market, Ukraine, Belarus. These models differ in the amount of heated water.
Bosch WR10.B, WR13.B, WR15.B
Before starting, check if the gas and water valves are open, if two R-type batteries of 1.5 V are inserted. These heater models are equipped with an electric ignition, as indicated by the B index at the end of the name. Electric ignition occurs with batteries.
To turn on the device, you need to press the power button on the front panel of the device, the speaker is ready for work, is in standby mode. In order for the heated water to flow, you just need to open the tap. At this point, the pilot flame ignites and after four seconds the main flame is ignited, thus the pilot flame extinguishes after approximately twenty seconds.
These devices have a constantly burning wick, which is economical since there is a constant gas flow. During a long break in operation, air can accumulate in the gas system, which will impede the correct operation of the igniter and, as a result, and will not be able to ignite the main burner.
To eliminate this problem, you need to open and close the hot water tap several times. Water heating is regulated by reducing its flow, by turning the valve clockwise it decreases, counterclockwise, respectively, on the contrary, the flow increases and the temperature decreases. At low water temperatures, gas consumption is reduced and less scale is formed in the heat exchanger.
In addition to the startup procedure, you can also find out about setting up the column:
How to light a gas water heater bosch Therm 4000 O WR 10/13 / 15.2 P.
The difference between THESE models lies in the amount of heated water per minute. A device equipped with a piezo ignition is designated by the letter P at the end of the name. It has the ability to regulate two parameters, water and combustion power. To turn on the column, you must move the slider to the ignition position, drown it.
Press the piezo ignition button several times until a flame appears on the ignition burner. Wait ten seconds, release the slider and move it to the desired power position. Moving the slider to the right increases the power and decreases it to the left. The column is in standby mode all the time, if you need to get hot water, you just need to open the valve with hot water.
When it is necessary to turn it off, move the slider to the left until it stops. After a couple of seconds, the pilot flame will go out. Rebuilt gas tap and water taps.
See below for instructions on how to enable:
Therm 4000 S WTD 12/15/18 AM E23 / 31.
Before starting, you must make sure that, on the plate installed by the manufacturer on the device, the gas marking corresponds to the gas to be connected to the device. The device has the ability to connect a remote control, which completely duplicates the work of the display on the speaker.
Open the gas cock and water valves. Connect the device to the mains.
The water temperature set by the manufacturer is 42 degrees, this is the optimal temperature.
To turn on the device, you just need to press the button to turn it on and open the hot water tap. To adjust the temperature, press the button or. and select the temperature you need. Until your chosen temperature is reached, the display will flash.
If It does not reach this value within thirty seconds, the water tap icon is displayed on the monitor, which indicates the need to increase or decrease the water consumption. If you press button P, the programmed constant temperature of 42 degrees appears. Setting the minimum temperature reduces energy consumption and makes it possible to reduce limescale deposits in the heat exchanger.
But if you know how to turn on the column, but are faced with malfunctions (the flame goes out, but does not ignite), then read this article, which describes the reasons and methods for their elimination.
How to turn on the gas water heater BOSCH?
2016-10-28 Evgeny Fomenko
Let us consider how to light a bosch gas water heater using the example of models of gas flowing water heaters Bosch WR10.B, WR13.B, WR15.B manufactured in Germany, for the market, Ukraine, Belarus. These models differ in the amount of heated water.
Bosch WR10.B, WR13.B, WR15.B
Before starting, check if the gas and water valves are open, if two R-type batteries of 1.5 V are inserted. These heater models are equipped with an electric ignition, as indicated by the B index at the end of the name. Electric ignition occurs with batteries.
To turn on the device, you need to press the power button on the front panel of the device, the speaker is ready for work, is in standby mode. In order for the heated water to flow, you just need to open the tap. At this point, the pilot flame ignites and after four seconds the main flame is ignited, thus the pilot flame extinguishes after approximately twenty seconds.
These devices have a constantly burning wick, which is economical since there is a constant gas flow. During a long break in operation, air can accumulate in the gas system, which will impede the correct operation of the igniter and, as a result, and will not be able to ignite the main burner.
To eliminate this problem, you need to open and close the hot water tap several times. Water heating is regulated by reducing its flow, by turning the valve clockwise it decreases, counterclockwise, respectively, on the contrary, the flow increases and the temperature decreases. At low water temperatures, gas consumption is reduced and less scale is formed in the heat exchanger.
In addition to the startup procedure, you can also find out about setting up the column:
How to turn on the gas water heater Bosch WR 10.2P?
A week ago, my mother had a gas water heater installed, but she DOES NOT use it. Doesn’t know how to turn it on, but she put the instruction somewhere and can’t find it. In the evening I’ll go to her, so I need help, tell me how to turn on the Bosch WR 10 gas water heater correctly. 2P?
The instructions for the Bosch WR 10.2P boiler indicate that the first start-up should be done by the one who installed the boiler, but if you decide to do it yourself, then follow the following order:
- Open the water and gas supply taps.
- There is a power adjustment slider on the front, press and hold it.
- Press Piezoelectric Gas Ignition Button.
- Release the button on the power regulator and move the slider left or right to set the desired power.
- Adjust the water supply with the appropriate regulator.
When you first approach this column, in fact it is not entirely clear how it will launch it, but then these actions turn to automatism. So, remember the procedure:
- The regulator is able to Turned off is in the extreme left position, you need to move it to the right.
- When the regulator is in position piezo ignition, then the spark icon on the case and the buttons vertically align.
- Now it is possible to press the button, but the action must be performed in this way. Drown her fingers inside and immediately press the inclusion of the piezo, there will be clicks, this piezo element will work.
- Look at the flame, it should burn with a small candle, this is a pilot flame, it must be held for about 10 seconds. During this period of time, the flame sometimes goes out, so you need to follow it, and if it goes out, then it will repeat the action. The extinction of the flame occurs as a result of the accumulation of air in the gas pipeline, so DO NOT be alarmed, it (air) just needs to be removed from there.
- If the flame does NOT go out, then we transfer the power to the desired one for this, move the lever to the right, respectively, the gas supply increases.
- Now the flame will burn constantly with the value that is set, but if you turn on the hot water tap, the column automatically starts heating the water.
- It turns off simply, it is necessary to move the slider all the way to the left, by this the gas supply is cut off and the flame goes out.
How to light a bosch gas water heater. How to light a gas water heater bosch Therm 4000 O WR 10/13 / 15.2 P.
The difference between THESE models lies in the amount of heated water per minute. A device equipped with a piezo ignition is designated by the letter P at the end of the name. It has the ability to regulate two parameters, water and combustion power. To turn on the column, you must move the slider to the ignition position, drown it.
Press the piezo ignition button several times until a flame appears on the ignition burner. Wait ten seconds, release the slider and move it to the desired power position. Moving the slider to the right increases the power and decreases it to the left. The column is in standby mode all the time, if you need to get hot water, you just need to open the valve with hot water.
When it is necessary to turn it off, move the slider to the left until it stops. After a couple of seconds, the pilot flame will go out. Rebuilt gas tap and water taps.
See below for instructions on how to enable:
Therm 4000 S WTD 12/15/18 AM E23 / 31.
Before starting, you must make sure that, on the plate installed by the manufacturer on the device, the gas marking corresponds to the gas to be connected to the device. The device has the ability to connect a remote control, which completely duplicates the work of the display on the speaker.
Open the gas cock and water valves. Connect the device to the mains.
The water temperature set by the manufacturer is 42 degrees, this is the optimal temperature.
To turn on the device, you just need to press the button to turn it on and open the hot water tap. To adjust the temperature, press the button or. and select the temperature you need. Until your chosen temperature is reached, the display will flash.
If It does not reach this value within thirty seconds, the water tap icon is displayed on the monitor, which indicates the need to increase or decrease the water consumption. If you press button P, the programmed constant temperature of 42 degrees appears. Setting the minimum temperature reduces energy consumption and makes it possible to reduce limescale deposits in the heat exchanger.
But if you know how to turn on the column, but are faced with malfunctions (the flame goes out, but does not ignite), then read this article, which describes the reasons and methods for their elimination.
All about geysers Bosch (Bosch)
- Content:
- The device and principle of operation of speakers Bosch
- Installation standards for Bosch speakers
- How to light a Bosch speaker
- How to clean a Bosch speaker
- Bosch speakers. Malfunctions and remedies
- Bosch gas water heater reviews
During operation, German gas water heaters Bosch (Bosch) have proven themselves only on the positive side. Instantaneous water heaters have simple and convenient control, are designed to be connected to one or more water points.
The Bosch range includes automatic gas boilers powered by batteries or a built-in hydro generator. The series also features classics. Semi-automatic boilers with piezo ignition.
Electric ignition
This type of ignition is used on models with an index at the end of the name: B.
Important! You can clarify the type of ignition of a particular model using the instructions. This type of ignition of Bosch instantaneous water heaters is used: W 10 KB, WR 15-2 B, WR 10-2 B, as well as in the water heater WR 13-2B.
To begin with, install two 1.5V R20 batteries in the battery compartment, usually they come with water heaters, the batteries are installed with positive contacts on the same sides, positive contacts should look towards the latch of the battery compartment cover. Also, instantaneous water heaters of these models have a battery charge sensor, when the battery charge is low, the LED on the control panel will glow red, with sufficient charge it will be green. In case of insufficient charge, replace the batteries.
Before putting the instantaneous water heater into operation, make sure that the gas used for the operation of the device is matched to the gas required for the operation. Of course, open the gas valve as well as the cold water valve.
To turn on, press the off button, which is located on the control panel. The device is in standby mode, now it is enough to turn on the hot water to start the device. Further. Carry out the required setting of the water temperature using the regulators. If the device is unstable, constantly turns off, then the problem is most likely a poor setting of the gas pressure, but certified specialists should be engaged in such repair of malfunctions.
Goes out when mixed
The mixer filter may be clogged, in which case clean it. Also, the flow of cold water can simply reduce the pressure of hot, for this it is necessary to set the appropriate temperature of hot water on the column.
How to clean the column ignition wick
If the igniter is clogged, the column will be unstable, for this you need to clean it, for which dismantle it, then clean the nozzle with a thin steel wire.
The Bosch column due to poor performance The wick may NOT ignite.
Goes out during operation
Perhaps the problem is insufficient draft, solve the problem with oxygen access to the burner, and also seal the burner manifold.
Piezoelectric ignition
This type of switching on an instantaneous water heater from Bosch is used in several models: WR 10-2P, WR 13-2P, WR 15-2P, as well as in column W 10-2P. In most cases, these models have similar ignition schemes. This type of ignition is semi-automatic
To turn on the column for the first time and further debug, first remove the metal protective casing from the column. After this procedure, check the setting of the length of the inflammatory flame, and also check the air gap between the nozzle and the ignition tube, it must be sufficient for the combustion of the inflammatory flame.
To ignite the appliance, move the slider on the control panel to the ignition position, usually this is the central position. Next, you need to make sure the gas supply. Press the button on the control panel sliders, at the same time press the piezoelectric ignition button, which is located just below the slider and the control panel itself, as a rule, one press of the piezoelectric ignition button is enough to ignite the inflammatory flame, but still you should make sure that the igniter is working, Otherwise, press the button again until the ignition flame switches on. Next, you need to release the button on the sliders of the control panel, the flame, of course, does not have to go out.
The next step is to set the maximum temperature: to do this, move the slider to the maximum power position, that is, to the right, return the temperature controller to the maximum position, and open the hot water tap, the instantaneous water heater should start working. Next, it is necessary to check the gas pressure, if the gas pressure is higher than the required one, the temperature of the combustion products will be higher than normal, which is why the operation may not be stable. In which case, make the setting.
Possible other reasons
The main reasons why the Bosch column does NOT light up are the incorrect setting of the gas pressure. To do this, it is necessary to make the necessary adjustment, and then the burner will burn stably.
Traction check
It is necessary to check the quality of the draft into the chimney. It is needed to remove combustion products (ha) from the kitchen. It is easy to do this: a thin strip of paper or a napkin must be brought to the exit window of the chimney. If the traction is good, the piece of paper will deflect towards the hood.
The flame deflected towards the chimney. Means good traction
Lack of traction. This is a problem that needs to be addressed. Check if the passage is not blocked. To do this, you will have to look into the inspection hatch. It is located in the chimney of the column to the place of its connection with the common house. Many people, unfortunately, close the hatch for decorative purposes. There is a second way to check and clean the chimney, so the hatch must be opened.
Most often, the problem is solved immediately: all the dirt, clouds of dust, fragments of bricks that have fallen from the chimney masonry accumulate in this place. Next, using a mirror or a phone with a camera and a flashlight, you need to check if there is a blockage upstream of the pipe.
Sometimes there is such a situation: the passage is clean, but there is traction. It could be an airlock. Some cold air accumulated at the bottom and blocked the pipe. It is necessary to warm up the air. To do this, right in the Luke, you can burn something or heat this place with a lighter-KOi (tourist match).
Preparation for work
If the gas water heater needs to be started for the first time or after a long downtime, some rules must be followed.
How to turn on the gas water heater correctly
A gas water heater in many homes is the only way to obtain hot water. Despite the obvious simplicity of the design, some users have questions about how to properly turn on and operate the gas water heater. Consider the nuances of the safe use of the unit.
How to light a gas water heater
After all diagnostic procedures, the column can be put into operation.
Do I need to turn off the column at night
In old models of speakers, as well as in those where a piezo ignition is installed, the wick is constantly on. On the one hand, this is not economical, since gas is constantly being consumed, on the other, it is potentially dangerous. It is better to turn off these speakers at night and sleep well.
It is not necessary to turn off a modern gas water heater
Modern gas water heaters have an automatic ignition system. There is also a whole set of security hardware:
- Traction sensor;
- Flame sensor (monitors its presence)
- The temperature sensor allows you to keep it up to 90 degrees.
An alarm signal from any of them leads to an immediate shutdown of the column. This column can be left on. Usually this moment is not even registered in the manual.
Is it possible to turn on cold water when the column is on
Many users are lazy, but do not know how or do not want to set comfortable settings on their column, and regulate the temperature of the water, add cold water to it. You can’t do this, that’s why:
- This is prohibited in the user manual;
- When water is mixed in the heat exchanger, limescale appears, which spoils it.