How to load the line into the mower

How to replace line in any trimmer

Technological progress provides us with a lot of opportunities to get rid of manual labor. This includes, among other things, mowing grass, which required a lot of physical energy when using a conventional scythe. In modern conditions, this process is much easier, because the applied technique minimizes all costs. Devices such as electric and petrol trimmers have firmly taken the place of irreplaceable assistants in gardening. Mowing grass with their help has become more fun than hard and exhausting work..

Structurally, the trimmer consists of an engine, a rod and a working body, which, depending on the vegetation being cut, is either a mowing head or a milling disc. And if everything is more or less clear with the cutter, then sometimes questions arise with the nozzle. As a rule, they appear when the line ends..

How to properly wind the line on the reel? Understanding.

So, first unscrew the nozzle. This should be done by rotating the drum to the right. Here we have a drum with the remnants of an old fishing line in our hands. We open it. Most often, the lid is closed with latches that can be opened with a screwdriver, threading it through the holes and slightly pressing. Or you need to squeeze the latch and turn the cover in the direction of the arrow. In this case, the lid itself must be held, since reels with automatic line feed have a spring that, when straightened, can throw out all the inner parts of the drum. Gently pulling out the reel, remove the scraps of fishing line from it.

Now you need to take 5 meters of new line and fold it in half (to find the middle). In the middle part of the reel there is a notch (in some designs – a hole), for which we need to hook our fishing line. There is also an arrow on the spool showing the direction of winding. An important detail – if the reel has two compartments, then one half of the line should be wound in one direction, and the other in the other. When finishing winding, you need to leave 15-20 cm of fishing line free. There are also two notches on the top ring of the coil, through which these free ends need to be passed. We dealt with the winding itself.

The last step in the line replacement process is to assemble the drum. First you need to install the spring and washers in their place. Then, holding the reel with one hand, with the other you need to thread the ends of the line into the corresponding holes on the sides of the nozzle. After that, install the coil in its place, pulling the line and being careful not to dislodge the spring. When all the internal elements of the nozzle take their places, you can close the drum with a lid. You just need to make some effort to ensure that the latches fall into place. Voila! The mowing head is ready for use!

Automatic line winding on a spool

There is a type of reel in which the automatic mechanism winds without the help of others – from the user it is enough to just fill the line correctly. How do I load the line into the trimmer spool? Video instruction. How to remove the spool from the trimmer? How to wind the line in order to tuck the line. The fishing line is passed through a hole on the inside of the body, its antennae without winding are threaded through the hole on the outer body, the reel is assembled, and when the winding button is rotated, the fishing line is wound from the inside without the help of others. In such a spool, it is unrealistic to make the winding wrong: the mechanism itself will determine the correct direction, since it can only rotate in one direction.

The warranty production of the factory trimmer refueling will inevitably require line replacement. Having a very rough idea of ​​how to thread the line into the trimmer reel on their own, beginners are reluctant to take up this business. However, with some skills, mastering this simple science does not present any difficulties, and the similar instruction presented below will facilitate this process as much as possible..

How to correctly replace the line in the mowing head, reel of STIHL FS 55 lawn mowers

Preliminary preparation

First of all, to wind the fishing line, you need to remove the spool (bobbin, spool) from the trimmer – specific actions will depend on the complexity of the configuration and the type of the product itself:

• small electric trimmers with a working position of the engine and spools at the bottom, as a rule, have side buttons on both sides of the bobbin. When pressed at the same time, the upper part of the spool together with the inner content for winding the line is detached, while the lower part remains on the trimmer. It is advisable to disassemble the bobbin on a flat, smooth place so that the spring included in the structure does not jump out and get lost;
• electric and gasoline trimmers with a curved bar without the possibility of installing a knife, as a rule, have spools with a special wing: in such designs, hold the spool in a stationary position with one hand, and rotate the locking reel on the bar with the wing nut counterclockwise with the other. After disconnecting the nut, the entire bobbin is removed.
• electric and gasoline trimmers with the ability to install a knife on a straight bar (for example, Stihl trimmers) have a hole under the reel. To keep the rod stationary, a screwdriver or other suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bobbin is fixed. After that, the coil body is scrolled clockwise (with a left-hand thread) and removed from the trimmer.

For the second and third cases, the coils, depending on the design, are disassembled in different ways. In bobbins with a lamb, a lamb is unscrewed, in coils with latches, the latches are pressed and one part of the coil is released from the other. If the halves of the bobbin are connected by thread, then it is enough to turn them by hand in opposite directions until they are completely unscrewed..

We carry out the winding of the fishing line

Slowly completed disassembly of the spool-spool without losing its spare parts allows you to proceed to the main task – winding fishing line into the reel. Technological features of the spool design and the number of working antennae determine the sequence of actions.

Coil with one working tendril

The simplest option and uncomplicated sequence of actions:

• The dimensions of the reel and the length of the original factory winding determine the recommended length of the line for winding – 2 … 5 m.
• One end of the line is inserted into the fixing technological hole located inside the spool.
• The fishing line is wound on the drum in the opposite direction of the spool rotation on the trimmer product – as a rule, on the inside of the reel, an arrow indicates in which direction the winding is carried out.
• A small section of the line is left free to bring it out – it is fixed in a specialized groove on the inner side of the bobbin, designed to hold the winding when assembling the bobbin into working condition.
• The left end of the line is passed through the hole in the outer part of the reel.
• The bobbin halves are assembled and put on the trimmer bar.

Preliminary preparation

First, to wind the fishing line, you need to remove the spool (bobbin, spool) from the trimmer – certain actions will depend on the complexity of the configuration and the type of the product itself:

• small electronic trimmers with a working position of the motor and coil at the bottom usually have side buttons on both sides of the bobbin. When pressed at the same time, the upper part of the reel, together with the inner content for winding the line, is detached, while the lower part remains on the trimmer. It is better to parse the bobbin on a flat, smooth place so that the spring included in the structure does not jump out and is not lost;
• electronic and gasoline trimmers with a curved shaft without the ability to install a knife, usually have spools with a special wing: in similar designs, hold the spool in a fixed position with one hand, and turn the locking reel on the shaft with the other wing nut counterclockwise. How do I fit the line into the trimmer? How to thread the line into the trimmer spool. It is clear how to load the line on the trimmer. After disconnecting the nut, the entire bobbin is removed.
• electronic and gasoline trimmers with the ability to install a knife on a straight bar (for example, Stihl trimmers) have a hole under the reel. For the rod to remain stationary, a screwdriver or other suitable object is inserted into this hole, and with unhurried rotation, such mutual placement is achieved when the screwdriver goes inside the hole and the bobbin is fixed. After that, the coil body is scrolled clockwise (with a left-hand thread) and removed from the trimmer.

For the second and third options, the coils, depending on the design, are disassembled by different methods. In bobbins with a lamb, a lamb is turned inside out, in coils with latches, the latches are pressed and one part of the coil is released from the other. How to fill the line in how to properly cheap line. 2. On your site. If the halves of the bobbin are connected by thread, then it is enough to turn them by hand in the opposite directions until they are completely unscrewed..

How to put line in the Stihl.FS-38 mower

took out the mower from the barn, but there was no line in it, I had to put the line and on the occasion took off a small

Coil with two working tendrils

In this type of spool, you should determine the number of grooves for winding the line, lying on the inside of the spool:

• one groove – both antennae are wound together in one groove;
• two grooves – each antenna is wound on an individual groove.

For both cases, a line with a length of 2-3 m is taken.In single-groove reels, the line is pulled into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the rod side – inside the arrow usually indicates the correct direction of winding. If there are fixing grooves, the ends of the fishing line are threaded through them or held with the fingers of the free hand, they are threaded into the through hole of the outer half of the bobbin, the spool is closed and attached to the trimmer bar.

The difference in line winding in double-groove spools is that initially a 2-5 m long line segment is folded in half (to determine the middle fold), and the fold loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each along its own groove, fixing the antennae and assembling the coil is similar to the above option with one groove.

The first execution of this procedure, perhaps, will seem long and rather laborious, but with time and experience this task will be solved much faster and easier..

The video below will clearly show how to thread the line into the trimmer spool and wind it correctly – this operation is not difficult and with some patience it will certainly be crowned with success:

How to choose a fishing line – length, diameter, restrictions

IMPORTANT TO REMEMBER! Do not use fishing line or metal cables for the trimmer. This replacement is ineffective and dangerous. The rope can injure not only the mower himself, but also those around him..
As for the length, you should rely on the estimated frequency of use of the trimmer. The more often, the more it costs to stock up expenses.

Information about the possible line diameter can be found on the body trimmer spools. Most likely, the range will be indicated there. The thickness varies from 1.2 to 4 mm. Choose the appropriate option, taking into account the characteristics of the cultivated area. The larger the diameter, the easier it is to mow tough grass.

The first way to wind the line

The required amount of line has been cut off. Now you need to carefully examine the bobbin in order to understand what type it belongs to. It depends on how the line is to be wound on it..

There are two types of bobbins. In general, they differ slightly from each other. Regardless of the type, the coil is divided into two sections – upper and lower. In the first type, the dividing edge does not close into a ring and has a depression.

In the second type, it is solid, but near it there are small through holes on the sides on both sides. The method of winding the thread should be studied depending on which of the above types the coil belongs to..

• The previously prepared six-meter segment must be bent in half. It is best not exactly in the middle, but in such a way that one half is about fifteen centimeters longer.
• Then the place of the fold must be inserted into the recess in the dividing face. One half of the line should be at the top of the reel, the other half at the bottom..
• Now you can start winding directly. You need to wind in the direction of the arrow on the bobbin. When winding, you need to hold the threads so that they do not intertwine and the upper half winds up in the upper part of the spool, and the lower half in the lower part. Each half should have about fifteen centimeters free from the end..
• There are small indentations (or, in other words, grooves) in the upper edge of the bobbin for securing the consumable. The ends of the threads must be inserted into these grooves so that they are fixed against each other..
• The final stage of threading the consumable into the tool – the ends attached to the bobbin must be threaded into the corresponding holes in the trimmer head.
• That’s all. The winding process is complete. Now all that remains is to assemble the head into a single whole. The spring fits neatly back between the bobbin and the head. Then you need to insert the bobbin into the head and press them together..
• It is recommended that the free ends of the thread be pulled out more. To do this, pull the ends of the consumable one by one so that they are removed from the grooves of the bobbin. You can make sure that the cutting element is removed from the retaining grooves by trying to pull the threads a little – they should freely exit through the holes in the head.
• While pressing the bobbin down, you need to put the cover over it. The cover must be screwed to the head so that all the grooves on their bodies are aligned and the bobbin remains fixed between them..
• And finally, the very last action – the head is screwed back into place at the bottom of the tool.

The process is complete. The line is tucked into a reel. The trimmer is ready for further work.

How to wind the line onto the trimmer spool

At first glance, threading a line into the reel of a tool is not an easy task. But it is enough to carefully study this process – and in the future all the necessary actions will be performed without any difficulties..

It is worth reading this guide to find out how to tuck the line into the trimmer. The step-by-step instructions below take into account the peculiarities of the spools of different types of trimmers, therefore, it is applicable to any tool.

So, the procedure is as follows..

• The line spool is the bottom end of the trimmer. First of all, of course, you need to remove this head from the device. To do this, you need to fix the rod (or, in other words, the shaft) on which the coil is attached. It is required to fix it in such a way that it does not scroll. The easiest way to do this is by placing a kind of stupor (preferably metal) between the shaft threads through a special hole. When the shaft is fixed, the spool can be unscrewed.
• At this stage, you have to remove the bobbin from the head, on which the fishing line is attached. To do this, you need to disassemble the head into elements. To do this, you first need to find a retainer on its body. It is located on the circumference of the product and is like a button. When the latch is found, you need to press it firmly. Keeping the latch pressed, turn the head cover clockwise. Then you need to remove the cover and remove the bobbin.
• A tight spring is placed between the bobbin and the head. It needs to be put aside for a while so that it does not interfere with the winding process. Before proceeding with the step of winding the line, it is necessary to inspect the bobbin. If there are remnants of old fishing line on it, they must be removed. When the bobbin is cleaned, you can start preparing a new bobbin..
• From a previously prepared skein of new fishing line, it is necessary to measure and cut off six (maximum – seven) meters. Keep the bobbin close at hand.

At this point, the key stage actually begins, which this article is devoted to..

Second winding method

• A previously prepared segment of six meters in length must be bent exactly in the middle and cut. Thus, two segments of the same length are obtained..
• At one end of each segment, you need to make a small “hook”. To do this, it is necessary to bend a couple of centimeters from the edge and fix it for a short time so that the “hook” does not unbend.
• Then one segment is taken. The hook is inserted into the through hole at the top of the bobbin.
• Now you can proceed to the key stage – winding. The direction in which to wind is indicated by an arrow on the bobbin. It is important to ensure that the line is wound strictly within the upper part of the reel. You do not need to wind the thread to the very tip – about fifteen centimeters should remain free from the end.
• In the upper edge of the spool there are small recesses (so-called grooves) for fixing the consumable. The loose “tail” of the thread must be inserted into one of these grooves.
• The top of the coil is tucked in. Now you need to do the same procedure with the bottom. Take the second piece of thread. The “hook” is threaded through the through hole at the bottom of the bobbin.
• After that, you can start winding the fishing line (within the lower compartment). And for this segment, you also need to leave about fifteen centimeters free from the end. This remaining “tail” must be inserted into the notch opposite to the one into which the end of the first segment was inserted.

The subsequent steps for this type of coils are exactly the same as described for the previous type in paragraphs five to nine..

This is how the line in the trimmer spool changes. There is nothing complicated in the process. And after several refueling operations, all actions will come to automatism..

To visually study the process described above, you can turn to the Internet for help. On the popular YouTube portal there are many different videos showing how to wind the line on the trimmer reel..

Preparation – remove and disassemble the spool

On most electric and petrol trims, you will need to remove the spool to replace the line. The FUBAG tool lets you skip this step. To make the instruction universal, we will still consider it in detail:

1. Secure the shaft. Insert the locking element into the corresponding hole. It can be a thin screwdriver or a metal rod..

2. Unscrew the bobbin case. In our example – strictly in the clockwise direction.

3. Unscrew the cover according to the direction indicated on the body.

4. Remove the coil for winding.

The preparatory stage has been passed. You can proceed to winding the fishing line.

Thickness selection

In addition, you should pay special attention to the thickness of the consumable. For mowing young grass, a thread with a diameter of one and a half millimeters is suitable. The larger the diameter of the thread, the drier and coarser weeds it is capable of overpowering.

When choosing a fishing line by thickness, there is one “but”. It is important not only to assess the capabilities of the material, but also to take into account the features of the trimmer. Be sure to check the user manual that came with your tool for information on cutting element requirements..

Using the wrong thread can damage the tool. Using a thread that is too thick will overload the machine’s motor. And the use of a thread that is too thin will significantly increase the wear of the twisting mechanism..

That is why it is necessary to approach the choice of consumables no less responsibly than to refuel it in the trimmer. When a suitable fishing line is found and purchased, you can begin to consider ways of winding it on a reel..

Features of the use of trimmers

A trimmer that mows grass with a fishing line can be used near: houses and other buildings, fences and hedges, trees and shrubs, beds and flower beds, row spacing in a garden plot.

Such a convenient, and most importantly, effective device like a trimmer exists in several variations:

As the names suggest, trimmer types differ markedly from one another. But regardless of the type of this tool, a fishing line can be its cutting element. Of course, the line tucked into the trimmer reel is not endless. And sooner or later you will need to replace it with a new one..

EASIEST WAY TO STRING YOUR WEED EATER

Line consumption directly depends on the frequency of use of the device and the scale of the work performed. The more grass is cut and the more often it is trimmed with the trimmer, the more active the line is used in it. And, accordingly, the faster it will end. In this regard, the question arises: how to thread the line into the trimmer spool?

Not everyone knows the answer to this question. But the winding of the line on the reel plays an important role in the trimmer operation. For the device to function properly, it is very important to properly wind the new line onto the reel. How to change the line on the trimmer, and will be discussed in this article.

Line selection

For the threading of the line into the trimmer head to be successful, it is important not to miscalculate with the choice of consumables. The thicker the cord you tuck in, the thicker and tougher grass it can cut. Often a universal line is used, the diameter of which is 2 mm. You can choose a diameter suitable for the mower in the following ways:

• Refer to the instructions that came with the trimmer for line thickness information..
• Pay attention to the bobbin itself. Sometimes information about the possible diameters of the fishing line is applied on it..
• Another option is to try inserting the cord into the exit hole. If it easily goes through it, then the selected line diameter is suitable for use..

Trimmer reel

You can choose a cord thread according to the type of engine. If the line is too thick, then the resistance to rotation will increase – in this case, the engine will overheat and will soon fail. Helpful hints:

• For an electrical device with a motor less than 500 V, a 1.3 mm thread is suitable. If one is not found, then you can use a 1.6 mm line. If the power is more than 1 kW, then select a cord with a diameter of 2 mm.
• With a petrol trimmer, the shaft mower matters. For the folded version, a 2 mm cord is often used. If the shaft is straight, use a 2.4-2.5 or 3 mm thread. The thickest line is installed on powerful devices – from 1.3 kW.

Pay attention to the type of section of the cord thread. Some popular options:

• The most common round lines. They mow fresh grasses well, but they cope worse with shrubs, dead wood..
• Twisted (spiral) cord is not very strong, but is good for thin young grass.
• Serrated thread with sharp edges is ideal for large weeds in a neglected area.
• You can mow your lawn more evenly with rectangular, star or square trimmer lines, but they are not very strong..
• Strongest – two-piece inner-core round cord.

Types of trimmer line

Please note that you cannot use wire, metal strings and cables, as well as ordinary fishing thread instead of fishing line. The device will be dangerous to both the user and others. So the cable or similar products will gradually begin to work, as a result, their ends will unravel, and small pieces will scatter at high speed..

How to tuck line into the trimmer: a few simple tips

Thanks to modern power tools, a person is given a lot of opportunities to reduce manual labor. These innovations include the trimmer, which greatly facilitates the process of mowing and lawn care. This device reduces the time for gardening work, turning difficult physical work into entertainment. The trimmer uses a fishing line as a cutting tool. It stretches strongly and thus mows grass of almost any height. It is quite easy to operate a power tool, but the problem arises when the cutting material runs out. Not everyone will immediately figure out how to tuck the line into the trimmer. Although this is a simple operation, it is not always clear to a person who is faced with this task for the first time how to properly wind it on a reel. Moreover, the instructions do not contain information on how to choose and replace the trimmer line..

How to quickly and correctly tuck the line into the trimmer?

Once you figure out how to change the cutting material, further use and maintenance of the trimmer will be greatly simplified. To wind the trimmer line, several operations should be performed, namely:

• Unscrew the nozzle by rotating the drum to the right. You will have a head in your hands with the remnants of an old thread. Open it with a screwdriver, or wring out the latch and turn the cover in the direction of the arrow. This operation should be carried out carefully, since there is a spring inside, which, straightening, can throw out all the internal parts of the drum. To change the line in the trimmer, you need to take out the spool and remove the rest of the material.
• Take 5 meters of new thread and fold it in half. There is a hole in the middle of the spool where you need to insert the material. There is also an arrow indicating the direction to reel in the trimmer line. It is important to consider some points. If the spool has two holes, then half of the trimmer line should be tucked in one direction and the other in the opposite direction. When finishing inserting the material, it is better to leave 15-20 cm free.
• Assemble the drum, reinstall the spring and washers. Then, while holding the spool, thread the ends of the line into the holes on the sides of the nozzle. Then put the head back in place, tightening the cutting material.

How to tuck the line into the trimmer?

In order for the area near the house to always look well-groomed and neat, it must be cut regularly. Fortunately, modern technology allows you to solve this problem without excessive physical effort. Electric trimmers are so easy to operate and maintain that even a teenager can use them to mow. The main thing is to figure out in advance how to fill the line in the trimmer.

How to load the line into the trimmer?

So, our task is to properly load the line into the trimmer. Let’s take a closer look at where to start its implementation and what pitfalls can await us in the process..

Step 1 – choosing the line

Step 2 – remove the coil from the trimmer

To perform this operation, the trimmer must be disconnected from the mains and turned over with the working head up. The further course of action depends on the trimmer model and the design of the coil itself:

• for small trimmers with a lower engine position, press on the keys on the sides of the coil and remove its upper part from the head;
• on trimmers with a curved bar, we clamp the coil body with one hand, while simultaneously turning the winglet located on the body counterclockwise;
• for trimmers with a straight bar and a gearbox, insert a screwdriver into the hole located under the coil, and then turn the coil body counterclockwise.

Step 3 – disassemble the coil

After the coil is removed from the head, it must be carefully disassembled. It is better to do this on an already mown area, since there may be a spring inside the coil, which will be quite difficult to find in tall grass. After disassembly, we will have three parts on our hands: the body (top cover), the protective casing and the coil itself.

Step 4 – measure the required amount of fishing line

Newbie mowers are usually interested in how many meters of line to wind on the trimmer reel? There are two ways to solve this issue:

• Unwind a skein of line on a flat, dry place and separate half of it.
• Measure 3-4 meters of line from the skein.

In any case, after the end of winding, the turns of the line should be on the body of the reel, without sliding off it. You do not need to try to wind as much as possible, as the line will unwind poorly and tear more often..

Step 5 – winding the line onto the reel

How to attach the line to the trimmer depends on the coil design. Consider the option when the reel body has one outlet for the line. In this case, the end of the line is clamped in the crevice of the coil, and then we wind the line, trying to lay the turns as tightly as possible. The direction of laying the turns should be opposite to the direction of rotation of the coil and is usually indicated on its inner part. After the end of winding on the reel, you must put on a protective casing and bring the end of the line into it.

If the reel is designed to work with two tails, then the line must be folded in half and laid in the groove in the center of the reel. Further winding will be carried out along one or two slots, depending on the coil design. The direction of winding must also be opposite to the direction of rotation of the coil. At the end of the ponytail, the line will also need to be led out into the holes on the top of the reel..

How to change the line on the trimmer

Below we have provided step-by-step instructions for replacing the trimmer thread..

The first thing to do is to unplug the tool and turn off the engine. Then you need to remove the trimmer head. This can be done using a simple screwdriver and dropping it into the hole of the gearbox to prevent the shaft from turning. And then just unscrew

They are usually unscrewed in a clockwise direction, but different models have different mechanisms, so it may have to be turned in the opposite direction. But if suddenly, for some reason, you cannot figure it out, then we strongly recommend that you refer to the user manual to understand how to disconnect it.

Second. After removing the mowing head, open it. This can be done by means of clamps that are located opposite each other. By pressing on them, you can remove the head cover, and then pull out the spool on which the line is wound. By pulling it out, you can determine what type it belongs to. There are bobbins one-piece and two-piece

We analyze how to thread the line into the trimmer spool in two versions

So, there is only one option – we load the line into a single-section reel. The prepared piece of thread is folded in half and pushed into the spool. Then, we begin to wind both ends in the same direction, which will be indicated by the arrow on the spool. At the end of winding, do not forget to make sure that different ends of the thread are looking in different directions.

Option two – winding the line with a two-piece reel. The pre-prepared thread is divided into two parts, and its ends must be fixed: this must be done by placing them in special fasteners

Winding is carried out, as in the first case, along the arrow indicated on the spool. Both segments should be wound so that they do not cross. Further, the ends of the thread should be fixed in the grooves and divorced on opposite sides.

The spring is then inserted into the reel and the whole thing is placed in the mowing head. When placing the spool in the trimmer, you need to gently hold the spring parallel while inserting the line into the slots on the mower head. And in the end, it just needs to be secured with the final part, that is, with a lid..

After threading the trimmer, you need to check it. If you did everything correctly, everything will work, but if you make a mistake, we recommend that you read the article again, or even better, if you watch the video on how to install a line on a reel in a trimmer.

How to remove the line from the trimmer spool

Over time, the cutting element of the head wears out, and it becomes necessary to pull out the remnants of the old line. Not everyone knows how to do this. Our step-by-step instructions plus a video on how to pull the thread from the trimmer spool, which you can find on the net, will help in solving this issue.

It is necessary to disassemble the mowing head

Remove the cover using the clips

We clean the remnants of cutting material

Hard ? Of course not. But if, nevertheless, doubts creep into you that for some reason you cannot do this, then of course find and watch the video how to pull out or how to wind the thread on the reel of lawn mowers.

How to wind the line onto the trimmer spool

05 July 2018

The trimmer is a great solution for those who have a large garden or lawn near the house that needs to be constantly trimmed. But like any other tool, sometimes it requires intervention. After some time, it will become necessary to replace certain elements, and this will have to be learned.

How can this be done? To replace the main cutting element, you must first select it correctly. In principle, the instruction manual for lawn mowers should indicate the diameter of the thread to be used in it..

When you have acquired the required cutting element, try to install it correctly. It should be noted that there are a huge number of videos on the Internet that will help you figure out how to properly thread the line into the trimmer coil..

How to replace the line on an electric trimmer

In fact, it makes no difference which oblique you use, be it electric or gasoline. Threading is the same. The only difference is that if you use a gas streamer, you get more freedom, since you are not limited by the cable that is present on the electric streamer.

Yes, do not hesitate to use the special videos on installing or threading the line in an electric scooter, which can teach you much faster than simple reading..

How to Wrap the Line on a Trimmer Spool Correctly – Step-by-Step Guide VIDEO

How to wind the line onto the trimmer spool

Preparation – remove and disassemble the spool

On most electric and petrol trims, you will need to remove the spool to replace the line. The FUBAG tool lets you skip this step. To make the instruction universal, we will still consider it in detail:

1. Secure the shaft. Insert the locking element into the corresponding hole. It can be a thin screwdriver or a metal rod..

2. Unscrew the bobbin case. In our example – strictly in the clockwise direction.

3. Unscrew the cover according to the direction indicated on the body.

4. Remove the coil for winding.

The preparatory stage has been passed. You can proceed to winding the fishing line.

How to choose a fishing line – length, diameter, restrictions

IMPORTANT TO REMEMBER! Do not use fishing line or metal cables for the trimmer. This replacement is ineffective and dangerous. The rope can injure not only the mower himself, but also those around him..

As for the length, you should rely on the estimated frequency of use of the trimmer. The more often, the more it costs to stock up expenses.

Information about the possible line diameter can be found on the body trimmer spools. Most likely, the range will be indicated there. The thickness varies from 1.2 to 4 mm. Choose the appropriate option, taking into account the characteristics of the cultivated area. The larger the diameter, the easier it is to mow tough grass.

Winding Algorithm

Insert the resulting loop into the groove.

Lay the line in the direction indicated on the element body.

Insert the short end into the slot on the side of the spool.

Secure the long end in the opposite groove.

Place the spool of coiled line into the spool body.

Pull the line out of the locking grooves.

Put on the cover and fix.

Trim the ends of the line, leaving 10 to 15 centimeters.

The replacement of the line is completed and now it remains only to screw the bobbin onto the trimmer and you can work.

ATTENTION! Typical line problems

No wonder they say: “Forewarned is forearmed“. Knowing about possible problems and the causes of their occurrence, you can prevent them in time. We recommend to remember or leave a memo.

Problem	Cause	Decision
Line break	Stones, branches and solid objects in the grass	Avoid collision
	Poor cord quality	Replace with a quality analogue
	Head outlet wear	Complete replacement of part required
The line is unwound	The spring in the coil is weakened	Check spring and replace if damaged
The line is sticking	Poor line quality, due to which it can melt under the influence of temperature from the heating head	Reel in less line or replace with a better line

String Trimmer Head | How to install new trimmer line on a traditional bump head

For a better understanding of the mechanism of the process of changing the line in the spool with a video guide prepared by FUBAG specialists:

Method 2 – how to properly put the line on the reel of lawn mowers with photo description and video

The second method differs from the first in that it is not a single piece of equipment that is charged into the coil, but segments from two parts. This method is used by manufacturers, and it is also suitable for those who have leftover material. The principle of how to insert two lengths of line into a lawn mower‘s line is the same as with the first method, and to make sure of this, below are detailed instructions:

• There are two equal length pieces of material that you can use.
• One piece is taken, and the edge is bent in the form of a clamping bracket or hook, with which the fishing line will be fixed
• Inside the coil there are holes in the form of a bracket for fixing, which are there for a reason. If they are not there, then the second option will not work. The appearance of these brackets is shown in the photo below. Each bracket is in its own half
• The brace of the fishing line should be hooked on the bracket, and wind it in observing the direction of the arrow
• The rig is wound until a 10-15 cm segment remains, which is fixed in the corresponding hole on the side of the guide
• Manipulations with the second end of the fishing line are carried out in the same way.
• The protrusions are inserted into the holes of the head, and then, removing the equipment from the temporary fasteners in the reel, a cover with latches is installed

The above instructions on how to install a fishing line in the lawnmower will help not only correctly, but also quickly make the replacement procedure. Assembling the trimmer coil, as mentioned above, can be done without removing the head, but in this case, you will need to conveniently fix the tool. Video instruction is presented below.

Method 1 – how to properly wind the line or put it on a reel and choose the required length

To implement this method, you will need to first prepare a fishing line of the required length (usually up to 4 meters). It all depends on the thickness of the equipment used, as well as the design of the coil. There is an easy way to find out the amount of line you need to refuel to charge the reel. To do this, wind the rig inside the coil until it is aligned with the side protrusions. In this case, the rigging should not go beyond these extreme protrusions..

The thicker the equipment used, the shorter its length will be needed and vice versa, the thinner, the longer the segment will be needed..

The instruction on how to properly tuck the equipment into the trimmer or lawn mowers is as follows:

• To begin with, a piece of fishing line that was prepared to be installed in a reel must be folded in half. In this case, one edge should protrude more than the second by 10-15 cm
• After that, take the second end from the other side, and fold it in half. Move to it so that the measured protrusion of 15 cm is preserved
• There is a slot in the inner baffle of the coil, into which the resulting loop should be inserted. The cut in the wall is shown in the photo below.
• Next, we find out the direction of winding the line. If you wind the rig in the wrong direction, then it will not function correctly, and you will need to redo the work. To insert the line and wind it in the correct direction, inspect the surface of the spool. The direction of winding should be indicated on it (in 99% of cases, this direction is indicated). What the direction indicator on the coil looks like is shown in the photo below.
• This arrow-shaped pointer can also have the designation, as in the example above “WIND LINE”, which means the direction of winding. If the pointer is missing on the reel, then you need to look at the head. There is a direction of its rotation on the head, and in order to properly wind the line, wind it on the drum in the opposite direction to the indication of the arrow indicator. So, if the arrow is on the tip, then you need to wind in the indicated direction, and if it is not there, then you should wind against the direction of the arrow on the surface of the head
• Having decided on the direction of rotation, you should start winding. Each end should be guided in its own groove. If there is no separator, then the equipment must be laid in the appropriate distribution order.
• When almost all the fishing line is wound on a reel, you will need to do the following – place a short part in the hole of the side wall of the pickup, the protrusion of which should be up to 10-15 cm, and then do the same procedure with the other end, placing it in the hole on the parallel side
• We insert the coil into the head, first passing the ends of the fishing line into the holes of the drum
• We put the drum in place and, by pulling the ends of the line, we disengage them from the temporary clamps in the wall of the reel. After that, you can put on the cover until the latch engages.
• This completes the process of how to replace the fishing line on the trimmer, and if necessary, you can only trim the ends (if their length does not suit), and install the assembled drum on the tool

With how to put the drum in place, no difficulties arise. There is also a second way, how to charge the mowing equipment in the lawn mower. What is the difference, and how is the second method of threading the line on the reel of lawn mowers carried out, we will find out in detail.

Learning to properly wind the line on the trimmer reel and lawn mowers installation instructions

Owners of private houses know how necessary this type of tool is, such as a trimmer. It can be gasoline and electric, but they differ in the design of power units. For cutting grass in areas where there are stones, trees and other obstructing objects, a fishing line is used as a cutting device. This consumable wears out during use, so how to wind the trimmer coil, we will consider in detail in the material.

How to remove the spool from the trimmer and remove the line

Initially, remove the line from the trimmer spool before inserting it into the trimmer spool. A reel or aiming device is a device that sits inside the mowing head, bobbin or drum. There are different types of heads (depending on the manufacturer), but the principle of replacing the line on the reel is the same for everyone. First of all, we will figure out how to remove the head from the tool, as well as how to get the drum and fishing line out of it..

The instruction on how to unscrew the manual head on the trimmer is as follows:

• Turn the tool upside down and, if necessary, clean it from dirt. With two fingers of one hand, grip the cover latches (on the mowing head), which are symmetrically positioned to each other. After lightly pressing them inward, remove the protective cover from the drum
• Next, remove the line spool from the drum shaft. It is mounted on a shaft without fasteners, therefore it can be dismantled with one hand
• The main part of the drum is fixed with a screw, which must be unscrewed with a screwdriver with an appropriate tip or bit
• To unscrew, hold the drum base with one hand, and unscrew it counterclockwise with a screwdriver with the other.
• After that, you can start dismantling. To do this, you do not need to pull it with all your strength, but slightly shaking it to the sides, slowly disengage it from the metal shaft on which the drum is seated.
• When reinstalling, fit the head into the square slots

This process is not difficult, and as you understand, there is no need to dismantle the entire head if you know how the replacement is performed. When dismantling, consider the following nuances:

• Periodic removal of the head is recommended to prevent corrosion of the threaded connection. If you never unscrew the screw, then if necessary, it will be difficult and even impossible to do this.
• If the screw has a four-sided bore of the head, then for unscrewing it is necessary to select a screwdriver or bits of a suitable size in order to exclude the licking of the edges on the head
• When assembling the unit, treat the threaded seat with lubricants, for example, grease or machine oil.
• If the edges on the screw are licked, then special clamping pliers can be used to unscrew it.
• There are drums that do not require preliminary disassembly. To dismantle them, grab it and rotate in the opposite direction to the clockwise direction

Knowing how to disassemble the drum, you should continue to figure out how to replace the trimmer line. The video below shows a detailed process on how to open the trimmer coil and disassemble it..

What you need to know about trimmer line

A fishing line is a consumable that is made of nylon and serves as a cutting device. By means of this equipment, the grass is cut, which is ensured by rotating the tool head at a high frequency. This material has different thicknesses, which depends on its use on the corresponding tools low-power electric (from 1 to 1.6 mm), electric from 500 W (2-2.4 mm) and gasoline trimmers with lawn mowers (from 2.4 to 3 , 2 mm).

The more powerful the tool, the correspondingly thicker the cutting equipment should be. This affects not only the quality of the grass cut, but also the service life of the material. If you are wondering how to wind the trimmer coil, then it is time to change and recharge the tool. With the onset of spring, this question is becoming more and more popular, so it’s time to figure out the step-by-step instructions for replacing the line in the trimmer reel..

How does a line head work on a lawn mower why you need to know how it works

Depending on the manufacturer, the heads differ structurally not only externally, but also internally. Most drums have a pressure spring inside (semi-automatic and automatic). Above is an instruction on how to disassemble the trimmer head without a spring, i.e. on the head of the manual type. The principle of dismantling a semi-automatic head with a spring inside is almost identical to the instructions described above..

The principle of operation of the semi-automatic trimmer coil is as follows:

• Inside the head there is a coil, which is fitted on the slots, which prevent its free movement.
• A spring acts on the coil, which presses it against the splines in the cover structure
• A fishing line is wound on the tip, the length of which depends on the tool itself. Typically this length is between 1 and 4 meters.
• During the performance of work, if it is necessary to increase the length of the line, the protruding part of the drum is pressed, whereby it disengages from the splines. In this case, the line is unwound from the drum, increasing in length
• After releasing the required amount of fishing line, release the pressure and continue cutting the grass

The advantage of a tool with a line is that this consumable does not require sharpening, compared to metal discs. In addition, if a stone or a tree comes across on the way, the line simply breaks off, without negatively affecting the gearbox and engine of the tool, as is the case with metal cutting discs..

Knowing the design and device of the types of mowing or trimmer heads, it is necessary to go on to consider the process of threading the line into the trimmer spool. After all, it is this very moment that causes difficulties for most owners of special tools..

Step-by-step instructions on how to wind the trimmer reel and lawn mowers

In order not to be mistaken with the choice of a suitable fishing line for your tool, you should first disassemble the head and look at the side wall of the reel. This information is usually presented on a tip, which will not allow you to make mistakes with the use of the appropriate equipment..

If there is information on the reel about the diameter of the line you can fill in, then this information can be clarified in the instructions. Having decided on the thickness or diameter of the rig, it remains to figure out how to charge it. There are two ways to do this, but not all of them are applicable. Let’s consider both methods in detail, and depending on which models of lawn mowers and trimmers you use, you decide on your own which option is suitable.

Tips and tricks on how to wind the line and what you need to know

There are some useful tips and tricks that will be useful to learn not only for beginners, but also for experienced mowers. These tips will help prevent negative consequences in the form of injury and improper functioning of the mechanism. These guidelines read as follows:

• It is necessary to install the cover until it clicks. Moreover, this is 2 or more clicks, which depends on the number of latches. If one of the latch does not snap into place, the drum may jump out when starting the tool and injure a person.
• Do not reel in the line with a strong pull, or more than you can insert it into place. It is better not to wind up the rig than there will be more of it, as this will lead to negative consequences in the form of the impossibility of unwinding it if necessary
• If you own a tool not with two line leads, but with one (usually these are low-power units), then the winding process is carried out in the same sequence as described above, only with the difference in the absence of a middle edge between the extreme bases of the coil
• After replacing the material, it is necessary to first check the operability of the tool, and after that start mowing the grass. If you do not make a preliminary check, then the scaffolding can unwind and injure a person

The result of the work done is as follows – after the replacement of the new material, the usual one is enough for an area of ​​up to 600 square meters, but taking into account the presence of a reinforcing layer on the fishing line. Conventional nylon materials last less, which is important to consider when working. Do not try to cut thick-stemmed grass with fishing line, as there are special metal discs or knives for this..