How To Make A Generator From A Tiller • CIMFLOK.COM

Generator wiring diagram

When installing and connecting the generator, it must be remembered that an incorrect connection of the electrical circuit will lead to a short circuit in the generator winding. To prevent this, the device must be connected strictly according to the instructions in the algorithm below:

Connect the generator to the electronic unit of the agricultural unit with two wires. The unit itself is equipped with 4 wires, 2 of which are blue. to them Connect the energy converter;
This leaves you with a black and red wire. Connect the first of them to the engine ground of the tiller;
The red wire is responsible for the output of the converted voltage, which is required to provide power to all electrical devices of the tiller without a battery. headlights, lighting and a sound signal. If the generator is installed on a tiller with a battery, then the converted energy is supplied to the battery and the electric starter of the unit. He will tell in more detail about connecting the generator to the tiller.

The generator connected in this way works according to a rather simple scheme: The generator installed on the tiller generates electrical energy, after which it is fed to the rectifier in the electrical unit. The unit contains a current regulator and voltage equalizer, designed to protect the electrical system from voltage surges and control the amount of energy generated.

When the tiller is started, its motor transmits torque to the rotor via a belt. During this, the generator begins to generate the required amount of energy and supply it to the electrical unit. Due to the fact that a certain amount of battery energy was spent when starting the motor, all electrical devices available on the Tiller will receive energy from the unit. As soon as the unit battery is charged, it will again become the main power source for the tiller’s electrical appliances. If the battery is discharged again, power will come from the electrical box. This process is repeated continuously as long as the tiller is running.

How to choose a generator for a tiller?

It can be quite difficult for a novice farmer to choose the right generator for a tiller. However, not everything is as complicated as it might seem at first glance.

The single most important factor to pay attention to is the power of the device. Whichever generator for an agricultural machine you choose, its power must necessarily exceed the total power of the loads under which the tiller works. This will allow the device to work properly under a voltage of 220 Volts without the risk of surges in the electrical network, and to power all electrical appliances available on the Tiller.

Oftentimes, NO experienced tiller owners purchase and equip their vehicles with generators designed to be installed on vehicles. This is the best option if the farm regularly uses a powerful heavy-duty tiller. In the second cases, it is impractical to buy such generators due to their high cost.

Generator for a tiller: which one to choose and put on your own

A modern tiller is a complex unit consisting of many fundamental elements. One of them is a generator, the function of which is to power an electric battery or lighting devices of an agricultural machine. Let’s look at the features of choosing a generator for a tiller, installing it and making it yourself.

How to put a generator on a tiller. an algorithm in detail

Before installing the generator on an agricultural unit, you should study in detail the structure of the existing element. The tiller generator consists of the following parts:

Case. in most cases it is presented in the form of a metal box equipped with a front and rear cover;
Pulley. this part is designed to transfer mechanical energy from the engine to the generator shaft through the belt;
Stator. the role of this part is played by the usual rewinding from steel sheets assembled in one compact package. In its shape, the stator resembles a pipe, inside which the power of the generator is generated;
Rotor. this part is in the form of a steel shaft equipped with two metal bushings. In the area between the bushings there is an excitation winding, the wires of which are connected to the slip rings;
The brush assembly is a plastic part responsible for the correct operation of the generator;
Voltage regulator. this part is responsible for voltage stabilization when the load level on the generator changes.

Installing a generator n tiller with your own hands takes a lot of time, but spent it, you ensure the smooth operation of your agricultural machine. It is necessary to connect the generator to the unit in accordance with the electrical diagram, which contains and describes all the connections necessary for installation.

How to make a generator for a tiller. just about complicated

Making a generator for a tiller with your own hands is quite simple if you follow the correct procedure. An electric motor is required for operation, which must be installed on an agricultural machine. The generator manufacturing algorithm is as follows:

First you need to install an electric motor on the tiller frame. It is best to use a pre-made frame for this, screwed to the unit frame with screws. Place and fix the electric motor in the frame so that its shaft and the shaft and the shaft of the standard tiller motor are located strictly parallel to each other;
Next, you need to install 2 pulleys. install one of them on the shaft of the tiller’s gasoline engine, and the second on the shaft of the electric motor used. An important role for the proper operation of the entire system is played by the correctly selected diameter of the used pulleys. the speed of the electric motor depends on these dimensions. In order for the generator to work without malfunction, the diameter of the pulleys must be equal to the nominal diameter, which is indicated on the packaging of THESE parts. It is even better if the real diameter of the pulleys is 10% larger than the nominal;
Having finished the mechanical assembly of the generator, you can proceed to connecting it to the tiller. To do this, use the electrical diagram above.

A homemade generator from an electric motor does not require special care. However, to extend the life of the device, a number of rules should be followed.

When operating a tiller, pay attention to the following nuances:

If you find that the electric motor installed on the tiller has become very hot, then replace the standard motor capacitors with elements with a lower capacity;
The voltage of the capacitors installed in the electric motor is of great importance. The best option for work is considered to be capacitors with a voltage of at least 400 volts. If this indicator is lower in the standard capacitors of the electric motor, then replace them with suitable elements;
Try to operate the tiller with an installed generator in dry weather, as moisture that can get into the electric motor will inevitably lead to a short circuit inside the electrical system.

By adhering to the listed rules, you will prevent damage to your homemade generator and significantly extend its life.

The methods listed above are suitable for the manufacture and installation of generators on the Neva brand Tilleri, as well as agricultural machines of the second domestic and foreign equipment manufacturing companies.

Generator for tiller

The generator is an important element of a modern tiller, the main function of which is to supply electricity to the battery, headlights and other electrical appliances of the agricultural unit. Offers to consider the features of self-selection, installation and self-production of a reliable generator of a household tiller in more detail.

How to put a generator on a tiller. self-assembly procedure for beginners

Installing a generator on a tiller with your own hands is a rather simple procedure, because for installation it is enough to install and fix the purchased spare part in a special niche provided for in the unit design. The situation with connecting the generator is much more complicated. At this stage, you should be extremely careful, because the slightest mistake will lead to a short circuit in the area of the winding of the generator used. To avoid this worthy possible damage, you should study in detail the connection diagram of the used electrical spare part.

The procedure for connecting the purchased generator to the used household tiller is as follows:

You need to connect the generator to the tiller using two identical wires. The unit itself has 4 wires. Two of the available wires are colored blue. they should be connected to the installed generator;
After that, the wires, colored red and black, will remain free. The second will need to be connected to the mass of the tiller engine;
The remaining red wire is responsible for the output level of all the voltage converted by the device. it is necessary for uninterrupted power supply to all electrical devices available in the tiller design without a battery. In the event that the generator is mounted on a unit with a pre-installed battery, then the converted energy will be supplied to the existing electric starter and the built-in tiller battery. In the correct connection of the purchased generator to the tiller, he will tell in more detail.

During operation, the tiller motor generates a torque, which, through a belt, is transmitted to the rotor. In this case, the generator generates voltage and transfers it to the electrical unit. When the engine is started, the capacity of the battery in the tiller will decrease, as a result of which energy will be supplied to electrical appliances from the electrical unit. This will be repeated until the tiller battery is fully charged. In the future, electrical energy will be supplied to the devices from it.

How to choose a generator for a household tiller?

In the modern electrical appliance market, you can find a huge selection of generators designed for installation exclusively on tillers. A wide range of products sometimes plays a cruel joke with novice farmers, as a result of which an inexperienced owner of an agricultural machine buys a factory generator that is not suitable for his tiller.

To avoid mistakes, one very important rule should be adhered to. the selected generator for the tiller must have power. Exceeding the total number of powers of all loads, which are acting on the tiller during its operation. Compliance with this factor when choosing a generator will allow the unit to operate stably under a voltage of 12 Volts, eliminating the risk of a short circuit or sudden voltage surges.

It is not uncommon for farmers to buy and install car generators on their tillers. This solution fully justifies itself only if the farm uses a heavy tiller with high power. For light and medium agricultural units, it makes no sense to purchase such generators due to their high cost.

How to make a generator on a tiller?

Making a generator for a tiller used on the farm is much easier than it might seem at first glance. This requires a fully functional electric motor. it should be installed on the tiller. The sequence of actions for manufacturing a generator is as follows:

First of all, the used electric motor should be fixed. To this end, you need to make a frame, which must be screwed to the tiller frame with screws. Next, a motor is installed on the frame, while the shaft of the latter must be in a strictly parallel position in relation to the shaft of the standard tiller motor;
After that, you will need to fasten 2 pulleys. The first one is mounted on the shaft of the standard tiller engine, and the second one is mounted directly on the shaft of the used electric motor. It is very important to correctly determine the diameter of the pulleys used. if the size is selected correctly, the electric motor will rotate faster, which will allow it to generate more electricity. In order to exclude possible malfunctions in the operation of the generator, the diameter of each pulley used must be equal to the diameter indicated on their factory container. Pulleys with diameters 10-15% larger than the size indicated on their packaging are also suitable;
After making a homemade generator, you should start connecting it. For this, the same electrical circuit is used as described above.

When using a home-made generator, you will need to Ensure that neither it nor the electric motor used for its operation, and not overheat. You should also completely exclude the ingress of moisture inside electrical devices. Another important rule is the voltage of the capacitors present in the electric motor. This parameter should always be a little more than 400 watts. if the power of the elements is lower, then it is advisable to replace them with suitable parts.

The generator made in this way can be used to work on Neva tillers and agricultural machines of the second popular domestic and foreign manufacturers.

How to choose the right generator ?

The first thing to note is that the power of the selected unit must exceed the power of the installed load, the generator must continue to work without a voltage surge when all electrical appliances are running on the tiller.

For equipment such as a tiller, generators from a car are suitable.

Mounting the device on a tiller

Many people ask themselves the same question, how to install a generator on a tiller without a battery? In order to put the device with your own hands, it is advisable to follow some rules and know what the device consists of.

The body is a steel container.
Pulley. is a conductor of mechanical energy.
Voltage regulator.
Rotor. a shaft made of steel and two bushings, between which there is a winding.
Brush assembly. made of plastic and takes an important place in the proper functioning of the generator.
The stator is a classic rewind, power is generated inside it.

In order to put a car generator on a tiller, and it will not take a lot of effort and time, but this should be taken responsibly.

Since the performance of the equipment as a whole will depend on this. The generator is mounted to motor vehicles using a special diagram, where all connections are indicated. In case of incorrect connection, the winding may catch fire. Do-it-yourself installation of the generator on the tiller is carried out thanks to two wires. In general, the block contains 4 wires, including 2 blue ones. It is through the two blue wires that the converter is connected. Then the red wire feeding the headlights and charging. The following drawing will help create.

Generator for tiller

A powerful tiller must be equipped with an electric generator. The generator for the tiller is one of the most important elements, it supplies the headlights with electricity and recharges the battery.

The battery is source of autonomous power supply, it is necessary, first of all, so that the tiller starts up without any special difficulties thanks to the starter, and for feeding electrical devices in the future. The main function of a 220 volt generator is to convert mechanical energy into electrical.

Making a tiller generator yourself

Defective tillers, as well as mini-tractors, are used for the production of generators. You can also make an electrical device yourself from a tiller, the power of which is 220 volts. A conventional induction motor can be adapted for a generator.

To assemble the device with our own hands, we need a powerful motor. that’s 16 kW, but not less; 1000-1700 rpm / Min.

Self-made generator from tiller

Many people experience power outages in their homes and this is NOT uncommon. Someone is saved by traditional methods, Using candles, gas generators, etc. But there is another solution to the problem: a do-it-yourself electric generator made of a tiller, capable of generating electricity. For this, an asynchronous electric motor is useful. The frequency of revolutions is 800-1600 per minute with a power of up to 15 kW. It is connected through a drive belt and pulleys with a motor removed from a motorcycle. In order for the speed of the electric motor to be 15% higher than the technical value, it is necessary to select a pulley with a suitable diameter. Star Combining the motor windings, in turn, the capacitor is connected in parallel to each of them. A triangle emerges. For proper operation, it is imperative to have the same capacity for all generators.

Installation wiring diagram

To put a generator from a car on a tiller, it is worth knowing that if the generator is not properly connected to the electrical circuit, then the winding is likely to light up. Installation of an electric generator is carried out using two wires. There are four wires in the block, two of which are blue. It is with their help that you can connect the converter. The red wire outputs voltage, supplies the headlights and signal, charges the battery. Black wires are connected to the power device array.

Generator connection diagram

The electrical circuit works quite simply. The generator produces electricity, which passes to the rectifier in the electrical unit, which is equipped with a voltage equalizer and current regulator. The equalizer keeps the voltage from fluctuating, regardless of the amount produced. And the regulator controls the current flowing into the battery.

The engine starts and transmits the rotor torque via a belt. The device, in turn, generates voltage to the electrical unit. Starting the motor reduced the capacity of the battery, which means that the devices will draw electricity from the electrical box. This will happen until the battery charge is restored again, and the power of all devices will again go from it.
To the menu

DIY headlight connection

To get started, you need to purchase (or find at home) an element for the lighting system. Every second owner of a mini-tractor also has other equipment (moped, scooter, car, tractor), to which spare headlights are attached.

The next step is to buy an electrical wire and a toggle switch (switch). After installing and securing the switch, they start working with the headlight. It is recommended to attach it to the front of the engine or to the steering column. It would be better to attach the headlight to the steering column tube, because if it is placed on the front of the engine, then it will be very dirty in rain or mud.

Then the wires are pulled. If the device is equipped with a hole for connecting the headlight, then it should be connected to it. Otherwise, power is supplied from the terminal of the oil pressure warning lamp. Next, connect the cord to the tumblers, and from it lead to the headlamp. The wires are attached to the steering column with a clamp or electrical tape.

How to make a generator for a tiller. just about complicated

First you need to install an electric motor on the tiller frame. It is best to use a pre-made frame for this, screwed to the unit frame with screws. Place and fix the electric motor in the frame so that its shaft and the shaft and the shaft of the standard tiller motor are located strictly parallel to each other;
Next, you need to install 2 pulleys. install one of them on the shaft of the tiller’s gasoline engine, and the second on the shaft of the electric motor used. An important role for the proper operation of the entire system is played by the correctly selected diameter of the used pulleys. the speed of the electric motor depends on these dimensions. In order for the generator to work without malfunction, the diameter of the pulleys must be equal to the nominal diameter, which is indicated on the packaging of THESE parts. It is even better if the real diameter of the pulleys is 10% larger than the nominal;
Having finished the mechanical assembly of the generator, you can proceed to connecting it to the tiller. To do this, use the electrical diagram above.

A homemade generator from an electric motor does not require special care. However, to extend the life of the device, a number of rules should be followed.

When operating a tiller, pay attention to the following nuances:

If you find that the electric motor installed on the tiller has become very hot, then replace the standard motor capacitors with elements with a lower capacity;
The voltage of the capacitors installed in the electric motor is of great importance. The best option for work is considered to be capacitors with a voltage of at least 400 volts. If this indicator is lower in the standard capacitors of the electric motor, then replace them with suitable elements;
Try to operate the tiller with an installed generator in dry weather, as moisture that can get into the electric motor will inevitably lead to a short circuit inside the electrical system.

By adhering to the listed rules, you will prevent damage to your homemade generator and significantly extend its life.

How to put a generator on a tiller. an algorithm in detail

Before installing the generator on an agricultural unit, you should study in detail the structure of the existing element. The tiller generator consists of the following parts:

Case. in most cases it is presented in the form of a metal box equipped with a front and rear cover;
Pulley. this part is designed to transfer mechanical energy from the engine to the generator shaft through the belt;
Stator. the role of this part is played by the usual rewinding from steel sheets assembled in one compact package. In its shape, the stator resembles a pipe, inside which the power of the generator is generated;
Rotor. this part is in the form of a steel shaft equipped with two metal bushings. In the area between the bushings there is an excitation winding, the wires of which are connected to the slip rings;
The brush assembly is a plastic part responsible for the correct operation of the generator;
Voltage regulator. this part is responsible for voltage stabilization when the load level on the generator changes.

How to properly put the generator on the tiller with your own hands. consider in detail

Installing a generator on a tiller with your own hands

A generator for a tiller or motor-cultivator of 220 volts is needed to power an electric lamp and headlights, as well as to charge a battery. The latter helps the technique to start up and charge all electrical appliances by means of a starter.

First, you need to choose the right generator. The power of the device does not necessarily have to be 220 volts. The main thing is that the power corresponds to the required load. An electric generator from a car and a tractor is perfect for this technique.

Do-it-yourself installation to a generator to a tiller is an easy task. The main thing is to follow the instructions and get acquainted with the Key parts of the installation:

Body. a metal container with a tire;
Pulley. transfers mechanical energy using a belt to the device shaft;
Voltage regulator. when the load level changes, it keeps the voltage at the same level;
Stator. rewinding, inside which the power of motor vehicles is produced;
Brush knot. a plastic element that helps the device to do its job correctly and accurately;
Rotor. steel shaft with two bushings, between which the field winding is located.

Possible problems and solutions

A serious breakdown, of course, cannot be solved without contacting a service center or professional repairmen. But with the current simple ones, everyone can cope independently. Among the most common user complaints, the following should be noted:

For the rest, it is obvious that the installation of a tiller generator is in no way difficult. over, in this case, there is a chance to significantly save on it, as well as to remain in complete confidence that it was made really qualitatively, with strict adherence to all norms and recommendations. Of course, this process will be difficult for beginners without experience in working with an electrician, but, what pleases, the acquired skill will be useful in the future.

How to choose a generator for a tiller correctly?

The standard and most universal version is considered to be 12 volts, and you can choose either a specially produced by the manufacturer as an additional accessory for a certain model of a tiller, or any other, including one used with another tractor or car. The main thing is that its power is greater than the load installed as a whole, since it will need to work without voltage surges, even if absolutely all electrical appliances are involved at the same time. For the rest, the Desired characteristics are calculated based on the planned scope of work, financial availability and ease of maintenance and repair of the device.

How to install a light on a tiller?

Most of the trailers are NOT originally equipped with headlights. Multiple headlights can be installed on heavy and medium units (main and rear for a trailer).

The power of the device that works is sufficient for the installation of additional equipment, as well as for the uniform simultaneous operation of all devices of the unit. Manufacturers have provided for additional installation of electrical equipment, therefore mini-tractors are equipped with electric generators with a power reserve of 30%.

Installing a generator on a tiller

There are two ways to install the light on the unit:

If you are the owner of a unit without a lighting system, do not despair. It is quite possible to set it to your taste. Some manufacturers offer separate lighting kits (wires, headlights and switch). There is a special hole on the engine of the unit in order to connect the headlight.
To the menu

Do-it-yourself mini tractor from a tiller. manufacturing procedure

Before you start making a mini tractor based on a tiller, you will need to prepare the materials necessary for work. Conversion kit includes:

Welding machine;
Screwdrivers and wrenches;
An electric drill and a set of various drills;
Angle grinder and a set of discs for working with metal;
Set of nuts and bolts.

Suitable drawings will help to correctly assemble a tractor from a tiller. In them you will find information about the order in which to connect the parts and what method of fastening is suitable for their reliable installation. Converting a tiller into a mini tractor is performed in the following order:

A minitractor based on a tiller must be equipped with a strong, reliable frame. It must withstand an additional pair of wheels, plus the load transported in the tractor will press on the supporting structure. For making a solid frame, pipes or metal corners are best. Be sure to keep in mind that the heavier the frame, the better the adhesion of the mini tractor to the road, and the better the plowing of the soil will be. The thickness of the frame walls is also not very important. the main thing is that they DO NOT bend under the pressure of the transported cargo. You can cut the blanks for making the frame using an angle grinder. Then all the parts are connected to each other first by means of bolts, after which they are finally welded to each other. To make the frame stronger and more reliable, equipping it with a cross beam;
Immediately after the frame has been manufactured, it can be equipped with a hitch, by means of which the small tractor will be equipped with additional devices. The hitch can be installed both in the front and in the rear of the supporting structure. If in the future it is planned to use the manufactured minitractor in tandem with a trailer, then Welding hitch follows to the rear of its frame;
In the next step, the homemade product is equipped with a front wheel. For this, the manufactured mini-tractor is best equipped with two ready-made hubs with brakes provided on them. Next, you need to fix the wheels themselves. To do this, take a piece of steel pipe, the diameter of which fits the front axle. Next, fix the wheel hubs to the pipe. Drill a hole in the central part of the pipe, which is necessary for mounting the product to the front of the frame. Then install the tie rods and adjust them in relation to the frame by means of a worm gear. After installing the gearbox, install the steering column. Here in the rear of the manufactured tractor it is mounted through pressed-in bearing bushings. Wheels used Must be NOT more than 15 inches in diameter. Smaller parts will lead to “burying” of the unit with the front part, and larger wheels will significantly impair the maneuverability of the mini tractor;
The next step is to equip the minitractor with a tiller engine. It is best to mount the motor in front of the machine, as this will improve the balance of the agricultural machine when operating with a loaded trailer. Provide a secure mounting system to mount the motor. When installing the motor, do not forget that the power take-off shaft must be secured coaxially with the pulley located on the rear axle of the mini-tractor. The force on the wheels must be transmitted by means of the Belt transmission. He will tell in more detail about converting a tiller into a mini tractor.

A self-made tractor will remain equipped with a reliable braking system and a high-quality hydraulic distributor, which is necessary for the proper operation of the unit with attachments.

Mini tractor from Tiller Bison

Tillers of this brand have a reliable and powerful enough motor, the presence of which allows the unit to be converted into an all-wheel drive minitractor. Be sure to Study the Detailed Drawings and buy steel sheets, pipes and angles before work. The procedure for manufacturing a minitractor is as follows:

When arranging the frame, you will need to expand the existing tiller frame. This is necessary in order to install additional wheels. Cut the corners and pipes into suitable pieces, and then weld them together;
The front beam of the mini tractor is mounted by means of a ready-made hub equipped with brakes. Wheels in the front of the unit Should correspond to the size of the rear wheels, or be slightly larger than the latter. this will prevent the mini-tractor from “burrowing” when driving over rough terrain;
Then install the tiller motor. It is best to mount it at the front to achieve the best balance of the overall structure;
Weld the towbar to the rear of the finished mini-tractor. it will be required for mounting the trailer.

A home-made mini-tractor, made on the basis of the Bison tiller, will be able to cope with a number of the most difficult economic tasks: plowing the soil, mowing grass, collecting and transporting crops.

Mini tractor from tiller 4 do-it-yourself manufacturing option

Many tiller owners often think about upgrading their agricultural equipment. In fact, it will NOT be difficult to improve the existing unit and make a full-fledged mini-tractor out of it. However, you will be required to study the recommendations and follow the procedure. this will give you the opportunity to get an effective home-made mini tractor, which will be able to solve absolutely all the tasks assigned to it.

Mini tractor from Tiller Neva

Converting a tiller into a small tractor may be slightly different. It all depends on the design features of the tiller and his abilities. Consider the principle of making a mini-tractor from Neva tillers.

As in the first case, before making a minitractor, you need to study the schemes. They detail the dimensions of the elements and the order of their installation during assembly. The procedure for rework will be as follows:

The frame is made in the same way as in the first case. To create it, use pipes of different sections. Fastening of the frame elements is carried out by means of bolts and quarrels;
Next, proceed to the manufacture and installation of the chassis. To install the rear wheels, use an additional here, which can be made from a steel pipe. Press the bearings and bushings into both ends of the latter, which will be equipped with the rear wheels;
Further, the tractor from the Neva Tiller must be equipped with a motor. over, the engine can be installed both in the front and in the rear of the frame. In the second case, the front and rear wheelbase of the mini tractor will need to be expanded;

In the end, the hand-made unit will remain equipped with a driver’s seat, lighting devices and side lights. Due to its small size, the finished tractor will have high maneuverability, which will allow you to effectively use it in hard-to-reach places.

How to make a mini tractor from MTZ tiller?

To remake the Tillers of this brand, you should also take into account their design and capabilities. MTZ units have a sufficiently high power, which makes it possible to make a full-fledged tracked mini-tractor out of them. It will be characterized by high cross-country ability and excellent grip, due to which the quality of plowing the soil in such a machine will be several times higher than that of wheeled mini-tractors.

Before starting work, be sure to study the drawings, in which you will find all the information required for the alteration. The procedure for assembling a mini tractor is as follows:

First put the tiller into mower operation;
Then completely dismantle the front platform of the unit;
Install a caterpillar drive in the front of the mini-tractor being manufactured;
Install an adjusting rod in the niche for mounting the steering rod. This element will increase the rigidity of the entire structure;
Weld the driver’s seat to the top of the frame;
Next to the motor, equip a platform for mounting the battery and hydraulic valve.

This method of manufacturing is suitable for converting MTZ 05, MTZ 09 and MTZ 12 tillers into small tractors. Each of them has sufficient power reserves to work together with a trailer and attachments at the same time.

Mini tractor from Tiller Agro

Before you start reworking the tillers of this brand, you should stock up on material and the necessary tools. To work you will need:

Stainless steel sheets and profiles;
Seat and steering wheel. can be removed from an old car;
A pair of wheels. their diameter must NOT exceed 15 ”;
A set of fasteners;
Angle grinder and electric drill;
Hammer and welding machine.

After preparing everything you need, we advise you to study the diagrams, which will tell you the correct procedure for installing the tractor elements. We also advise you to see photos that will certainly help you in the manufacture of an agricultural unit.
Unlike the tillers of the manufacturers listed above, the Agro brand equipment has one significant drawback, which must be taken into account when converting a tiller into a mini tractor. It lies in the fact that the tiller has very weak fracture strength. This kind of break will surely affect if you exceed the maximum permissible load on the mini tractor frame. To avoid further malfunction, the mini tractor will need to be equipped with wheel gearboxes.

The procedure for assembling the unit is as follows:

The first step is to weld a sturdy tractor frame. To do this, use steel profiles and pipes. Be sure to take into account that the heavier the frame made, the better the adhesion of the mini tractor to the ground will be. At the rear of the supporting structure, weld the towbar, which is required to couple the trailer to the unit;
Then proceed to the manufacture and arrangement of the mini tractor undercarriage. To do this, you can purchase a pair of ready-made front wheels, as well as hubs equipped with brakes. After purchasing the parts, attach the hubs to the steel pipe, and drill holes in the front of the frame, which will be required to mount the hubs on the mini tractor. Next, install the tie rods using a worm gear. Following the rods, secure the steering column and the rear axle. When installing the latter in the bushings used for mounting, press in the bearings. Install a pulley on the back and secure the wheels;
Then mount the engine to the front of the frame. We advise you to do this by means of an additional frame placed on special shock absorbers. this will avoid strong vibrations at high loads on the motor;
Next, install the driver’s seat on the mini-tractor, Connecting it to the frame through the springs. thanks to them, it will be much more convenient to work with the mini-tractor.

If desired, a self-made compact tractor can be equipped with a canopy, which will protect you from rain and sun. To make it, you need to weld 4 steel pipes to the frame next to the seat and steering column, to which a steel sheet is fixed by spot welding. As a result, you will receive a reliable unit for giving, which will quickly cope with all the tasks assigned to it.

Sources:

http://pro-traktor.ru/motobloki/generator.html http://pro-motobloky.ru/motobloki/generator.html http://arendavlg.com/motobloki/generator-na-motoblok-shema-podklyucheniya-ustanovka.html http://o-motoblokah.ru/samodelki/minitraktor