How To Make A Plow For A Tiller

How to make a plow for a tiller with your own hands? Just use our drawings and photos DIY plow for a tiller. Homemade according to the finished drawing. All sizes are visible in the photo, but you can see how our homemade plow is plowing

Plow strut mount

To fix the plow stand, holes 31×16 mm are drilled or cut out on both sides in the wide part of the pipe that was used to create the frame. Through holes of 10.2 mm are also made in the narrow walls of the frame for fastening, using M10 bolts, the handle.

The plow arms must be made separately from a pipe about half an inch in diameter. You can use an old water pipe, which needs to be flattened with a sledgehammer on both sides. Drill holes with a diameter of 10.2 mm in the planes obtained and bolt to the frame. To give more rigidity, weld the cross member between the handles.

Manufacturing and fastening of plow working elements

The main elements of the single-body design are the blade and the share, which require strong sheet steel 3-5 mm thick. First of all, a ploughshare is made, for which it is worth using an old disc from a circular, since it is made of high-strength steel. To sharpen the plowshare cutting edge, it must be beaten off on the anvil.

Next, you need to make a dump from a metal pipe with a diameter of 50-60 cm and a wall thickness of about 5 mm. A template is created from cardboard or thick paper, which is applied to the metal and traced around the entire contour with chalk. Then, according to the obtained lines, a workpiece is cut out by gas welding, which is brought to the required size using an angle grinder or a hammer and emery.

How to make a plow for a tiller with your own hands? Just use our drawings and photos

12/02/2015 193 Views

How to make a plow for a tiller with your own hands

Single-body models

Single-body units are the simplest in design. They have only one share and are used for plowing light soils in common garden plots that make up the majority of the land. Such a plow is not suitable for plowing heavy soils and virgin lands; a more powerful structure is required here.

The double-body plow consists of two frames with plowshares. It is used for processing various types of soils and for primary plowing of virgin lands. It will be able to carry out plowing and harrowing at the same time, providing the best quality of soil cultivation.

Homemade single-body plow

The simplest, but at the same time effective design of the plow is single-body.

This design is applicable for making it with your own hands at home. Manufacturing does not require special tools and devices, as well as special skills; the tools available in the workshop of home craftsmen will be enough.

Is it possible to dig potatoes with a plow

Many experienced farmers use the plow to harvest potatoes. So they significantly simplify their life, getting rid of the need to dig out hundreds, or even thousands of potato tubers. The only question that arises is, with what plow to dig potatoes?

By making a reversible plow with your own hands, you will make your life easier for many years during gardening and field work. And having mastered the business of manufacturing and selling this unit, you will certainly gain a stable income. It’s time to start your own business!

How to make a plow for a tiller and a tractor with your own hands

First, consider a plow for a tiller or mini tractor, which you can do yourself according to drawings. For a visual analysis of the device, we recommend downloading the drawings of the PN-2-20 double-body plow free of charge.

This plow is aggregated with agricultural machinery of drag class 0.2. These can be heavy tillers or mini tractors:

  • Belarus-082;
  • Belarus-112;
  • Belarus-132N;
  • Belarus-08K;
  • KMZ-012, T-0.2 (Uralets);
  • KhTZ-8 (Carpathian).

Brief technical characteristics of the PN-2-20 plow:

  • Capture width 0.4m;
  • Tillage depth up to 25cm;
  • Productivity up to 0.05 ha / hour;
  • Construction weight 67kg.

The cultivation of a large plot of land is a labor-intensive and energy-consuming process, which cannot be done without the use of technical devices. Thanks to the plow, the soil can be properly prepared for sowing, and also processed to get rid of weeds and dead wood after harvest.

The plow is attached to mechanized equipment, which, by means of a high draft force, sets the unit in motion. In the process of working with the plow, the top layer of the soil is pushed off by the share, and then it simply turns over. This allows not only to loosen the soil, but also to improve its aeration. over, tillage with a plow destroys up to 90% of the weeds growing on the site!

How to make this useful unit, which is necessary in every household? First you need to take care of purchasing the necessary high quality materials. For the plow blades, you will need steel about 5 millimeters thick. The ploughshare itself should be made removable so that it can be periodically taken out and sharpened. For the body, use hardened steel, which will not hurt to treat with anti-corrosion solutions before welding.

To make a special functional plow blade, be sure to adhere to the following guidelines:

  1. Cut the cylindrical working surface of the blade out of the metal sheet.
  2. With the help of a listogib, the cut parts are bent by 22-23 degrees, while the latter are strictly adjusted to the required shape and size.
  3. Please note that the size of the hollow metal pipe for the blade is about 55-59 centimeters in length. The wall thickness should not exceed 5 millimeters.
  4. The dump blank itself must be preheated in order to then perform matrix bending.

Directly the body for the circle can be made of a metal sheet with a thickness of at least 3-4 millimeters. A square with sides of 50 by 50 centimeters is cut out of it, to which a ploughshare, side shields and a blade must be attached in sequence. At the same time, make sure that the required angles between the plow components are strictly observed. The presence of gaps or inaccuracies during the installation can adversely affect the durability of the unit. Having welded all the parts together, you need to clean up the seams, and it is advisable to sand the ploughshare with a blade to avoid rust.

When you master all the intricacies of making a plow for tillers and mini tractors, you can proceed to more complex tasks.

5-case reversible plow on T-150 (PLP-5-35):

This is a 3D model of a 5-body reversible trailed plow PLP-5-35 for a T-150 tractor or other tractors with a pulling class of 3 and higher. Using this 3D model of a plow for production, you do not need any drawings. The structure is disassembled into more than 100 parts to the smallest detail. The project is created in 3D-format CAD STEP files. This format is supported by many CAD editors, including free FreeCAD.

Note. Working with the STEP format in FreeCAD is not very convenient. The program requires a lot of computer resources to download all the details of the device. Just opening a file on an average laptop takes about 10 minutes. If possible, use a paid professional AutoCAD program.

How to adjust the plow correctly

Thanks to the fact that you make a plow with your own hands, it becomes possible to adjust the dimensions of the share and blade to all the parameters you need. You can easily adjust the width or depth of the plow depending on the type of work to be done in the field, in the garden and in the garden. Also, you can adjust the parameters of the plow, taking into account how much power your tractor (or tiller) has. This will allow using the assembled unit with maximum utility, avoiding overheating or damage to traction equipment.

Plow setting steps:

  1. We tighten the nuts on the fasteners, but do not overtighten.
  2. We fix the plow with fastening using two metal pins.
  3. We carry out balancing by setting the desired angle of inclination.
  4. We check the quality of the plow in the field, and, if necessary, adjust the initially set parameters.

Remember that meticulous and precise tuning will allow you to complete all the necessary front of work much faster and more efficiently with less fuel!

How to make a plow to a tiller yourself

Now we will answer the frequently asked question of the owners who bought the tiller: how to make a plow for the tiller with your own hands. To make working elements, you need 3-5 mm steel. First you need to make a ploughshare (for example, a circular saw blade is suitable for it). The cutting part of the plowshares must be well sharpened and sharpened at an angle of 45 degrees.

The next step will be making a blade. For it, you can take a pipe with a diameter of 0.5 m and a wall thickness of 5 mm. Cut out the blank for the blade with a cutter and grind the angle grinder.

Having finished making all the parts, you can start assembling the plow body. To do this, we take steel with a thickness of 2-3 mm and assemble the entire structure.

So there are several types of plows, consider some of their features, plows are single-body, reversible and rotary.

Which plow is better for a tiller to choose, photos and descriptions

Any summer resident who wants to buy a plow for a tiller realizes that this acquisition can make it easier to plow the land, and with its help it is also easier to turn the upper layers to bury the necessary fertilizers.

Single body plow design

The simplest design is for a single-body plow (we discussed its manufacture above). It is with such a plow that you can start making for a beginner, in addition, there are a great many drawings of such a plow.
The reversible plow has a more complex design. Such a plow has a curved blade at the top of the body, which allows you to turn the soil layer during processing, which is especially optimal for hard soil.

To manufacture such a plow will require significant effort and much more knowledge (due to a more complex drawing and more careful selection of materials). It is also necessary to strictly follow all instructions in the manufacture of such a unit.