How to make a shock hammer with your own hands.

DIY Locking Hammer

This simple short video tutorial shows how to make a locksmith hammer without costs from improvised materials. This will be a small tool, since the author of this video on the farm has many different hammers, but there was no small. It will make it with your own hands from a square piece of instrumental carbon steel size 16 × 16 mm, 90 mm long. For this material, heat treatment is not required. You can use the wrong steel (45), it will later have to be tempered. The handle will be made from a wooden from a chair.

So, the chair was disassembled and the beech jump was removed, which became the basis of the handle. It is processed on sandpaper on the peeling circle. It is made as a wedge.shaped so that the iron part of the hammer clogs well. So that there are no burrs, polished by sandpaper by zero. Now she sits in her hand quite well.

For the head of the hammer to become brilliant, polished it on a tape grinder, removed all the bumps, rust. Then, on the peeling circle, he took off one side and the second. Uneven surfaces specifically for the convenience of operation.

The most severe part of the manufacture of the connecting unit. First made a hole with a small drill with a diameter of 4 millimeters. Then a drill 6 millimeters. Finally used 10 millimeters. Since the metal is very hard, it was very difficult to make a hole with a drill 10 millimeters. Therefore, processing was carried out sequentially from small size to maximum. Jumpers were removed with the help of a file.

The result was a beautiful locksmith hammer. Now it remains only to collect. We make, score further. We will beat the handle with a hammer and the handle will enter the connecting node. Book is not afraid of small shock loads. The pen entered the head and holds very tightly.

Further video channel Vitmana homemade

We make a hammer with our own hands. 74 photos of repair and creation of a tool. Step.by.step instructions for beginners

It is difficult to imagine a house in which there is no hammer. This tool is an indispensable thing. He will score a nail, help to split nuts, and sometimes you can’t do without it in locksmith work.

However, there are cases that it is broken or one head remained of it. And perform work that are connected with a hammer is simply necessary.

Therefore, you need to figure out how to make a hammer with your own hands.

Using a hammer

The history of the emergence of the hammer goes deeper. It was still used by primitive people. They found him the most different application. Used in construction, extraction, hunting.

By modification of the hammer, you can track how humanity has developed. Mainly the change affected only the material from which it was created. And the design itself remained unchanged

There are a huge number of types of hammers that are used in various areas of human life. So, it is used in medicine, construction, cooking, locksmithing. You can’t do without a hammer in these areas. However, each sphere has its own certain type of hammer.

The most popular and in demand is a regular hammer that is used in everyday life. Its popularity is explained by the fact that it is multifunctional and universal.

Its main goal is an increase in the power of the human blow. In addition to clogging nails, he is also an indispensable assistant for other construction tools. For people like Kerner, chisel, chisel.

The design of the hammer

• In the photo of the hammer, it is clear that it consists of two parts
• The handle can be made of the following materials
• In the manufacture of the box, use

• steel;
• copper;
• lead;
• wood;
• rubber.

Its shape and size depend on which area it is used. And the cost of the hammer is very strongly affected by the shape of the box.

Square is much cheaper than the round shape. Since its shock part has a much clearer accuracy, as well as a large impact power. The speed of any hammer can only be regulated by a person.

How to make a hammer

The tool begins to make a handle. Since the fighting itself is usually. Making it at home is problematic. Therefore, do not throw the old hammer heads.

The handle is most easily made of wood. To do this, I will approach 3t, the following trees

For manufacturing, a tree bar is necessary. The size depends on how long the hammer is required. The handle itself is pulled out of the bar. After that, it is imperative to roll it, so that later there is no discomfort in the work, and the skin on the hands does not suffer.

Prepared wood should be well dried, and then varnish. Drying room is selected carefully. Since it must comply with the basic rules:

It is important that wood cannot be dried with artificial lighting devices. Since it can be deformed, and its size will change a lot.

The next stage is the most difficult, this is the connection of the handle with a boy. The narrowed end of the handle with some effort should be inserted into the head of the hammer.

Often there are cases that the tip is not suitable in size. In the manufacture of the handle, it turned out a little more. This is not scary with the help of Rashpil can be processed to the desired size, and then fucked up so that the surface turns out to be smooth.

The boiler is planted perpendicular to the base of the handle. In this case, the structure must be kept in an upright position.

The head is planted with the help of gradual strokes on a solid surface until the handle enters the head tightly. Everything, the hammer is ready for use.

It is not difficult to make a hammer yourself, the main desire. Of course, you can buy a new hammer in the store, but this does not give a complete guarantee that the connection between the head and handles will not break in his new. Therefore, it is advisable to make a hammer with your own hands.

DIY hammer

Today we consider how the author did, here is such a soft hammer from a copper graphite brush. Such a hammer is not used often, but there are times where you need to work with the part without damaging it.

I made marks on the brush, retreating 33 mm on top, and from below 45 mm.

Combining the marks with a straight line, with a hacksaw on metal, he cut off everything unnecessary.

Further in the center of this workpiece, it will make a hole. First 3 mm drill, and then 6.5 mm.

He will also make a hole, and in a small piece of a wooden board by a 8 mm drill.

This piece of wood will be used as a guide for a tap.

Having cut a couple of threads of threads in the boy of the future hammer, he took off the guide and continued to cut the thread without it.

Then he changed the drill to the nozzle with sandpaper and began grinding.

And poured the resin into the hole of the handle, installed a hairpin and left until the resin is hardened.

After the resin was frozen, wrapped part of the handle with a leaf into the cage and fixed it with tape.

Then, with the help of an awl, he moved the cell marking to a wooden handle.

Then taking the old worn.out curly bat.

And with the help of not strong beats of the hammer, I went through the previously made marking.

Then he walked with sandpaper and applied several layers of stain.

Then he set the handle in an upright position, and covered it with alkyd varnish in two layers.

While the varnish dries, I decided to modify the fight of the hammer a bit, or rather, make an additional fixation of a wooden handle on it. To do this, he made a through hole from his side and cut the threads under the screw M 3.

Когда лаковое покрытие высохло вкрутил ручку в боёк.

I also made a hole in advance in the stiletto.

Fixed the handle with screws. Putting the pucks of Crover to avoid twisting the screws.

As you can see in the photo, there are not big damage on the shock part of the hammer.

But there is no scratch on a nail hat. That means made by the author, a soft hammer copes with his task perfectly.

Handle nozzle process on a hammer

Often the size of the hole of the head of the hammer at the upper and lower input is slightly wider than in the middle. Thus, the size of the handle for the handle in the thin end part must correspond to the size of the holes in the middle of the shock of the tool. It is necessary to check it without fail, a hole under the handle on a brisk tool is well made. How you can see it in the photo.

It shows a train of an old hammer that needs preliminary types of processing. Without these works, it will be impossible to perform the nozzle of the handle. Paying attention to the picture, we can see that the tide of the box was made poorly enough, the presence of large influxes of metal and unevenness is present, each entrance to the holes on both sides differs by 6-8 mm rather than in the middle of the box.

Types of hammers

Various types of hammers are used in various areas of repair and construction work. In this case, each model is made of different material, has a different structure and design. What varieties of hammers exist:

• The carpentry hammer is designed to work with wooden details, so often the back of the head is equipped with a nail. The mass is 100-500 g. Such lightness is necessary in order to make accurate, rather than force attacks. The hammer shock area is flat, and the handle can be made of wood, metal or metal.plastic. On the base of the handle, rubber overlays for strong grip are usually attached.

To the carpentry hammers can be attributed to the mallet. Such a tool is completely made of solid wood. Kiyanok designed to work with wooden details in those cases when there is a threat of dents on wood. Kiyanok is used to connect the grooves of wooden parts.

• The plaster hammer is intended not only for working with a clay surface. Such a tool is actively used in the process of installing drywall. A small device, and its shock part has a round shape. The back of the head is represented by a small ax. This design allows you to drive nails into it without damage to the finishing material or clean up (trimming).
• A rubber hammer is used to lay tiles, tiles or bricks. Accordingly, such a rubber hammer is also called kiyanok. The tool helps to compact and equal the fragile details of decorative building elements. Since a rubber hammer is called a kiyanka, then for working with a tree this type of tool is ideal.
• A hammer of a carpenter (roofer) is a tool with a metal head. The shock part can have a round or square shape, and its surface is usually corrugated. The head is additionally equipped with a nail with a nail or pointed “Usik”. The mass of the tool is usually 300-800 g. A tool for clogging nails, wedges and fitting wooden structures of roof and support beams is intended.
• There is a special shock tool for masonry, with which you can knock out a brick in the process of working with brick, concrete. Due to the presence of a flat narrow part, certain parts of the stone, brick or concrete can be chopped off. The bulk hammer has the name Kirka, and the people are named “cam”. The tool should be durable and not too heavy.

There are still types of devices that are used in narrow areas. Copper hammer looks like a sledgehammer, but the tip is made of copper. Such an alloy does not produce sparks at the time of the blow, so it can be used in flammable situations. A small analogue of a locksmith tool is suitable for a welder. But in such an analogue, a narrow part has a larger rock angle of about 45 °.50 °.

Depending on the type of work, the type of shock tool is selected. Different heading of the head helps to perform certain manipulations with different finishing and building materials.

Distinctive features of a hammer and sledgehammer

If we consider 2 options for percussion instruments that differ only in mass, then the question arises of how the hammer differs from the sledgehammer. Sledgehammer is one of the subspecies, but all the differences are stripped.

The main difference between these tools is the shock force and mass. In general, it is believed that the device for injecting, which has a mass of more than 4 kg is already a sledgehammer.

Basic rules for working with a hammer

A tool that requires special caution in circulation. Although the impact force depends on the type of hammer, even a light head when it gets into the head at low speed can lead to death. To avoid this, you need to know the basic rules of work:

• Work can be done with an exceptionally working tool. The head should sit tightly on the handle. There should be no chips on the wooden handle, its length must correspond to the weight of the metal part.
• The boiler should be whole without chips and cracks.
• The grip should be carried out at a distance of 3-4 cm from the end of the handle.
• In the work, an exceptionally even nail can be used in the work. Previously, a small hole is made for a nail. To do this, you can use an awl.
• Clogging is made so that the hand performs only vertical movements.
• Transfer the device from the hand to the hand only in the lowered position. In the same condition, a change of grip is also made.

If there is violations in some details, then the work with such an tool is strictly prohibited.

If at least 1 point is broken, then the master is in danger. The employee can get serious head injuries, hands or fingers up to death.

How to choose a hammer

It seems that choosing a hammer is not such a problem. In fact, there are a lot of nuances that should be paid attention to in the purchase process. When choosing a tool for the implementation of a certain type of work, you need to evaluate the following factors:

• Depending on the functional features, each option has a different type of shock. Therefore, you need to determine exactly what type of work is needed for.
• You need to carefully examine the handle for chips and more complex damage. A high.quality tool will have a perfectly even and dense handle, regardless of what material it is made.
• Much depends on the design. For example, a steel hammer consists completely of steel. Therefore, the pen should have appropriate extensions at the head and at the end of the handle. A special coating is provided, which will provide a good grip. If the design does not meet such conditions, then the tool will give a huge return or vibrate when hit.
• A heavy tool should have a thick and long handle as possible. Normally, the length is 38-45 cm. When the length of the handle is less, that is, the risk of getting serious injury due to a fracture of the base of the handle during operation.
• The next factor will be the weight of the tool. For use in everyday life, it is enough to have a hammer weighing 350-450 g. If you need to perform more serious construction or repair work (wall dismantling, roof repair), then the mass of the device should be 0.6. 0.8 kg.
• Requirements for the head in terms of fastening are the most important. The metal part should sit tightly on the handle, do not shift, do not deform, do not hang out. This aspect can be checked directly during the purchase process by making several swings.

It’s not so difficult to choose if you know and take into account all the nuances during the purchase. You need to pay attention to the structure and fastening of the tool, its capabilities and functionality.

Do.it.yourself slaughter hammer

In addition to the inverter, electrodes and masks, the welder always has to carry one tool with him. a special hammer for separating slag.

An ordinary hammer also does not cope effectively with this task, and it weighs more, so it greatly overloads the worker’s hand, because in the day you have to beat off slag from hundreds of joints. Therefore, special slag separators were developed, with different forms and functionality.

Happy welder of slag chopping can be made with your own hands. What is it better to make it, and what form is described later.

A wide arsenal of actions

The welder’s hammer is designed primarily for the quick compartment of slag, which is formed with manual welding with covered electrodes, or remains after a welding tractor using flux. It is very important to beat off the slag to check the quality of the connection, as well as with multi.layer seams, where the second passage is always carried out on clean metal, without debris and easily melting impurities.

Slag separator can be performed by other operations during the work of the welder. Among the most common:

• Drip. When burning the arc, partial spraying of the filler and basic material occurs. The hot drops adhere to the surface in the near.haired area, but do not weld it to it. To give an aesthetic look to the product, it is necessary to beat off the frozen splashes with a sharp side.
• If a non.brew was allowed, then in order to qualitatively redo this section, you need to completely remove the slag from the point or cleft in the seam. If this is not done, the liquid metal will flow through this place and the brew it will not work. You can do this with a sharp narrow edge of the hammer.
• Welding tools with a more massive design is suitable for breaking the seam on alloy steels. Tapping with a “stupid” edge on the junction will strengthen the structure of the metal in this place.
• The same product can be used to fit the parties to the desired level or gap between them.
• Bend the heated part and proceed to the surface for a more convenient seam will turn out to be a “heavy” version of the tool.
• In the process of welding, it is necessary to cut off a new cable from the coil to lengthen the mass or wire of the holder. This can be done with a hammer with a wide nose like Kirka.

Design features

In connection with the variety of work performed, models of welding hammers also differ. There are slag separators with a flat edge on one side and a sharp cone on the other. With this tool, it is convenient to beat off the slag and pick out points with uninvited places for re.passage. The second edge can be “stupid” and heavy, which is convenient for launching parts and breaking the seam.

If the flat side has a wide blade, and the opposite side is an even cut, then this is suitable for separating slag and chopping manipulations. Hammers in hammers can be metallic, which is practical when working with hot metal, or rubber.

They are better in hand. Models from a store with a wooden handle are convenient, but quickly spread out and break. Weight and size also vary. As a rule, the welder has several similar tools of different forms for specific types of work.

To make a hammer yourself just

It’s easy to make a welder of a welder with your own hands. You need several items and manipulations. You can start your project with the creation of a shock element.

The main task that is facing the master is to choose a material that allows you to maintain an acute cone or flat cut for a long time.

Frequent grinding on the sharpener distracts from work, and with a stupid hammer it is inconvenient to beat off slag. Therefore, you need to choose the right material.

An old chisel or chisel can serve as an excellent basis. Make slag separators from the construction kirok small or files.

True, the latter has the ability to fail at significant loads, so it should be used only to repel slag! For the shock part, the described part is required above 120-150 mm long.

Good material will be a peak from a penetrator with a winning tip. Having imprisoned a similar tool once you can work all week for eight hours.

But if there is no high.carbon iron at hand, then it is not necessary to specially buy a new doloto. From a piece of reinforcement, you can make a good shock material yourself. It is necessary to cut off a piece of 150 mm long and, heating it in the furnace or on fire, splash the edge.

After cooling, you need to sharpen it to a finished look. Then, the acute side heats up to the white color of the metal and lowers into machine oil. At this moment, the material is hardened and its hardening occurs. It is enough to repeat the procedure once.

The handle can be made from a bar of 6-8 mm in diameter. The length should be 200 mm. It will be practical to bend the lower edge in two layers to make the pen thicker and comfortable for capture.

You can put a hose or a handle from an old bike on it so that the tool does not slip out during operation. Some welders make a metal ring on their belt to insert a hammer into it.

So, he will always be at hand at the right time.

A welder hammer is a very necessary thing that helps to adjust the sides of the product for welding and check the quality of the seam under a layer of slag. You can make a good hammer with your own hands, instead of buying a store version that is short.lived.

Welder hammer. the purpose and characteristics of the tool

In addition to the inverter, electrodes and masks, the welder always has to carry one tool with him. a special hammer for separating slag. In the article, the master plumber will consider why he is so important for welders, what hammers of this plan are, and which are better.

The welder’s hammer is designed primarily for the quick compartment of slag, which is formed with manual welding with covered electrodes, or remains after a welding tractor using flux. It is very important to beat off the slag to check the quality of the connection, as well as with multi.layer seams, where the second passage is always carried out on clean metal, without debris and easily melting impurities.

Slag separator can be performed by other operations during the work of the welder. Among the most common:

• Drip. When burning the arc, partial spraying of the filler and basic material occurs. The hot drops adhere to the surface in the near.haired area, but do not weld it to it. To give an aesthetic look to the product, it is necessary to beat off the frozen splashes with a sharp side.
• If a non.brew was allowed, then in order to qualitatively redo this section, you need to completely remove the slag from the point or cleft in the seam. If this is not done, the liquid metal will flow through this place and the brew it will not work. You can do this with a sharp narrow edge of the hammer.
• Welding tools with a more massive design is suitable for breaking the seam on alloy steels. Tapping with a “stupid” edge on the junction will strengthen the structure of the metal in this place.
• The same product can be used to fit the parties to the desired level or gap between them.
• Bend the heated part and proceed to the surface for a more convenient seam will turn out to be a “heavy” version of the tool.
• In the process of welding, it is necessary to cut off a new cable from the coil to lengthen the mass or wire of the holder. This can be done with a hammer with a wide nose like Kirka.

Unlike slag chic, an ordinary hammer will not be effective when removing a crust from slag:

• Firstly, a simple tool has more weight and has a significant load on the hand of a working.
• Secondly, the design of the slag separator is such that it allows you to practically not feel the return.
• Thirdly, with an ordinary hammer it is possible to get not to every connection, t. to. He does not have pointed ends, unlike a special welder tool.

The welder has to perform different connections and seams. Depending on the type of work, the design of slag.chicken hammers also differ.

The main structural elements of the slag detector are a bilateral working part (boiler) and a handle.

The welder’s hammer should not have too much weight and other parameters. The optimal weight of the working part is about 0.4 kg, and the length is 15-20 cm. Handle length-25-30 cm.

The working part in the form of a bilateral head can be of different configurations. The following forms are common:

• The chisel of the chisel. On one side, the chisel goes along the handle, on the other. perpendicular to her. The welder can choose the position of the chisel that is convenient for it when removing the spray of metal and slag.
• Touch of a flat strike. It is difficult to meet a similar type on free sale, but it can be done on your own. The flat side can be flattened, crushed or bend the metal where you need, and remove the slag with a chisel.
• Peak (sting) chisel. In some models, the chisel is perpendicular to the handle, in others. along it. It is convenient to beat off metal drops and remove slags, as well as to carry the joints with a chisel. They beat off thin seams, and also get rid of unverified areas.
• Z-shaped peak. For the safety of work, it is better to clean the weld in the direction of “from yourself”. For this, models with a working part curved in the form of the letter Z are well suited.

Ergonomicity is very important for the welder’s hammer, it should be convenient to hold. The handle is made either from metal or from wood, in addition, they have some differences in shape. The following types of pens are common:

• Wooden. The tree softens the return on the hand when hit. Such a pen is nice and convenient to hold. However, it can burn from sparks during the welding process. In addition, you need to choose models that have safety plates, otherwise the head may start to fly over time.
• Metal. common than wooden. Resistant to wear. Non.combustible. Have an increased service life. But they can be cold in the cold. And there is also a danger of slipping from the hand of the welder.
• Spring. Metal handle, part of it. in the form of a steel spring. Softens the blows, not giving back. When heating the hammer, heat dissipates in the air. It costs more than relative tools with standard types of handles.
• Shock.absorbing (anti.guided). Can be either wooden and metal. Below is additionally covered with a layer of plastic, rubber, etc. P., which excludes her slipping out of hands. Due to coating with elastic material, mechanically does not much affect the welder brush. It is convenient to keep it.

As a rule, the welder has several similar tools of different forms for specific types of work.

DIY hammer

At the first glance at this instrument, his similarity with a long.known hammer and even sledgehammer becomes obvious. Indeed, she is his variety, but she has a different field of activity. Rubber kiyanka is aimed at work related to those materials that require more touching circulation.

And the rubber is distinguished by the fact that it is made from very solid wood, and another mandatory element will be a rubber component. Most often, such a tool will be from white or black rubber.

Most often, such a tool is used when working with don and chisels. However, when performing carpentry, it is quite possible to work with other tools.

Depending on what work is to be done, the following types of tools are distinguished:

Locksmith Kiyanka, she is also a locksmith hammer

If there are fucking work, then you can’t come up with anything better than such a tool. Take a hammer and a chisel to help and start doing work. It will be very good here to knock out precisely incisors.

If classes related to the editing of metal are coming, then it is best to use this type of kiyanka. over, this kiyanka will differ in appearance from the carpentry material. Externally, the locksmith “thresher” also differs from other similar ones. it looks like a rectangle that has a round handle.

In its functional purpose, it will resemble the previous. However, the manufacture of such a tool will occur already on a lathe.

Why is a rubber kiyanka used

Rubber kiyanka has found wide application in the carpentry and locksmith. This confirms all the activities that are carried out with its help. This is work on stone and wood, and a variety of roofing deeds, laying tiles on the sidewalk and even raising automobile surfaces. It turns out that kiyanka is needed wherever a thiner approach is needed.

Its manufacture is presented by special requirements. For example, the handle should be made of such wood species as a horned or knit. That is, the breed should be viscous and heavy at the same time. This will allow you to work especially comfortable with this type of tool.

It has its own characteristics in the manufacture and a hammer. it is important here that a handle is inserted into the opening of the cone.shaped shape of the box itself (the only way it can be guaranteed that it will not break during work).

As already noted, the working surface of the hammer can be made of black and white rubber.

It is better to stop precisely on the bright version. then there will be no trace during work during work.

The pen usually differs here. it is made of material that is not afraid of the effects of solvents. And working with such a tool of any person will be especially comfortable and convenient.

• The advantages and disadvantages of such “blocks”

• With all their undeniable advantages, such tools have a significant drawback. they differ not too much durability.
• This means that the material from constant operation, it can quickly become unusable.
• This is especially true for wooden models, but if we are talking about rubber, then there can only be one way out. only the highest quality rubber is used to make the head itself.

How to make a fault with your own hands

By the way, such a tool can be assembled on its own. To do this, just follow the following stages:

For the manufacture of a handle, it will be best to sharpen the blanks on a lathe. this will allow us to get a round section of the shape (and hence the more comfortable use of this tool in the finished form). And in the middle of the pen itself, you can make a ledge so that our future head has a cleaning. If this is not possible, it is worth winding the rope on the handle in several layers.

Before you make the head itself, you need to prepare a layout. As for the starting material, rubber can be replaced with skin. From it we will cut out the circles. it will take about 50 similar in order to collect the “block” itself in the finished form. If the skin is thin, then it is possible that there will be seventy such layers.

So that the prepared circles are easily strung on the handle, it will be necessary to cut the hole of the corresponding diameter in them.

Each such piece will need to be strung on the handle and fastened with the following PVA glue. When gluing, the layers will need to try to press as tightly as possible to each other.

Strung all the prepared material? Now try to squeeze it all in a vice until the moment the glue is completely dry.

So that in the future the head we collected does not fly off, it will be necessary to fix the puck over everything received on top of everything. It doesn’t matter here what it will be. wooden or metal. The most important thing in this whole process is that the bolt is very fixed. But you will need to choose it so that it does not crack.

If the dimensions allow, you just need to intercept the protruding edges and fix the head with an additional twine. Another option is to drive small carnations into the end.

That’s all. it is quite possible to use a kiyanka in work. You will immediately appreciate all its advantages: it is silent and very practical. When working, the head will not be split into the slightest chips, and the process itself will happen as silently as possible, as if it were with a model made of some other material.

I liked the post? And the evaluation of the publication. It’s not difficult for you, but the author is pleasant. Thanks.

A reverse hammer device

There are several options for the structure of the reverse hammer:

• vacuum;
• with a pneumatic mechanism of stretching;
• devices with several weighting agents;
• Models with an adhesive base or interchangeable nozzles.

The first of the presented species has a unique advantage over such devices. Vacuum suction cum allows repair work without damage to the paintwork. Depending on the power of the vacuum reverse hammer, it is possible to draw small and medium.sized damage on various parts of the body. However, when working, a special technology must be observed: stretching should be made from the edge of damage R to its center. Otherwise, there is a voltage dangerous for metal, which can lead to fracture or unlocked deformation.

Pneumatic reverse hammers are convenient in that they require reduced effort when performing work. Also, the sphere where this tool is indispensable is the work under the hood, including the extraction of accusited details.

A homemade reverse hammer can be built from the simplest components:

• a metal rod of a suitable thickness and a length of about half a meter;
• steel washers of the corresponding diameter for installing stops;
• weights to increase the force of exposure;
• rubber handle (it is possible to replace with any other convenient material);
• hook or metal plate with the holder. depending on the design of the alleged hammer.

It depends on the condition of all components whether the grinding and cleaning of metal parts will be needed. To do this, you can use sandpaper or disk for grinding metal, and special compositions may also be useful. It will depend on the design features whether the welding machine will be needed or only a device for cutting the thread will be required. However, most often it is impossible to do without welding, since fixing the locking washers on the reverse hammer rod is best done using a reliable seam.

Device design

You can find a reverse hammer for a body repair on numerous sites. But before designing it is important to determine the goals for which the tool will be used. A reverse hammer for rikhty can be done in half an hour with your own hands, but you need to select the scheme in advance. The easiest way to assemble a model with an adhesive base or with interchangeable hooks on the thread.

The first step is to decide on the size of the hammer. Typically, 50 cm lengths are enough to ensure prolonged work and convenience, however, reducing this number is possible depending on individual needs or the availability of the necessary materials.

The second stage is made a clear drawing on which each detail is carefully drawn. Thanks to this, the number of components and the degree of their readiness for assembly becomes clear. Most often, it is at this moment that you can think in advance and make hooks for stretching various sizes. Since the reverse hammer can be made with one or more cargo, such a variety of nozzles will allow you to work with dents of various severity. For example, with specific damage, welding of several loops on one straight line with the subsequent extension of the pin for stretching one plane is possible.

This method is not suitable for any dent, but it allows you to reduce the arising deformation forces in the metal, which allows you to do work faster and with minimal damage.

Self.manufacture

Making a reverse hammer at home with your own hands is quite simple. This does not take much time, and does not require special materials and tools. For a more visual understanding, you can watch a video on the Internet. The primitive drawing will also not be superfluous.

For the manufacture of this tool with your own hands, you will need the following:

• metal pin about 50 cm and 20 mm in diameter;
• cargo that has an internal hole;
• thread cutting tool (optional);
• welding machine;
• Corner grinder.

If it is decided to make a reverse hammer with a hook type of fastening, then a hook is made at the end of the pin. You can make it using a vise or pliers. Or weld a welding machine a ready.made hook from another device with a welding machine.

If the tool is made with a threaded capture, then the thread is cut at the end of the pin with an appropriate tool. You should not cut a lot of threads, since the body metal is quite thin.

After the manufacture of the tip, a load is put on the pin, which is limited to the back of the tool. This can be done by welding, or use threaded emphasis. The second method is more predominantly, as it will allow the use of loads of different weights depending on the required force at the end of the reverse hammer.

Brief instructions and tips on the use of tools

Again, in order to clearly understand how this happens, the easiest way to watch the video. If this is not possible, then the procedure for working with this device is approximately as follows:

• The tip is fixed on the deformed area of ​​the body;
• The details of the cargo are aligned to the desired position;
• If the effort is not enough, then the load changes to a heavier.

When stretching a relatively large section of the metal, you can weld several goals on one line and pass through them the pin. To do this right, it is advisable to watch the video on this topic. Then this pin is hooked, which is welded to the device and is pulled together with the metal, aligning it to the desired state. When using this method, you should be careful, since welding of a large number of washers can excessively pull the metal, and ruin the body part.