How to properly start a Stihl saw

We start Stihl MS 180 C

The device of this model, in comparison with the previous one, has some differences in the trigger mechanism, but it does not carry any changes in the triggering algorithm. The fact is that the ErgoStart system is installed in the Stihl 180 C, which, due to an additional spring installed in the chainsaw starter, reduces the engine resistance when starting.

If you cannot turn on and start the chainsaw

When all actions are performed in accordance with the established order, and the chainsaw does not start work, then there are malfunctions in its mechanism. Usually the cause of this phenomenon is common and easily fixable problems, such as lack of spark, shut off fuel supply, clogged filter that allows air to pass through. In order to start the chainsaw, you will have to find the cause and take the necessary steps to eliminate it..

Only correct actions should be taken. If a person does not know what to do, there is no need to commit rash acts. It is forbidden to disassemble the device, you need to be especially careful with the carburetor. You cannot unscrew any screws on it, because if its device has become the cause of a breakdown, then it is impossible to repair the chainsaw without professional equipment..

The actions that need to be performed in a strict order are listed. Only during the transition from one measure to another can you determine the exact cause of the malfunction and quickly eliminate it without damaging other parts. Algorithm of actions performed in case of failures in the establishment of a chainsaw:

How to Start a Stihl Chain Saw

• At first, it is enough to let the device rest. This is especially true for recently used saws. It is enough to wait no more than 10 minutes, since during this time the mechanism will cool down and in the absence of other breakdowns it will easily start. Sometimes it happens that a candle is poured near the appliance during the establishment. If this unpleasant property has occurred, then it is enough to wait a very short pause and repeat all the steps again to start the engine.
• The housing cover is unscrewed from the device to remove the air filter. The process of starting up the device is performed if it is absent. Sometimes the reason for the lack of ignition is that the filter is dirty. If ignition occurred without it, then the reason lies precisely in this. To eliminate these troubles, it is enough to wash the filter under running, warm water and soap, then dry it. It is also possible to replace the old element with a new one..
• The spark plug is removed. The spark is checked. If it does not appear, you need to replace the old candle with a new one. Usually this helps and a spark appears, but in some cases there is no spark even when changing the mixture..

This means that the ignition unit is damaged, and the chainsaw needs professional repair. Sometimes there is a malfunction of the ignition unit even in the presence of a spark, therefore, this criterion cannot be followed to eliminate the likelihood of breakage.

When a spark appears when it is impossible to get the device to work, you must continue to perform the steps described below..

Chapter 9: Starting Your STIHL Chainsaw

There are times when a spark appears, but the candle itself is moistened. This is possible if gasoline gets on it. To get rid of it, it is enough to turn the device over so that the cylinder is facing downwards. Then all the excess liquid will pour out. Next, you should check the combustion chamber, for which you need to pull the starter more than 10 times. A candle damaged by moisture can be replaced with a subsequent check of its effectiveness. If it becomes faulty, you can replace this element with a new one. After these steps, you need to try again to activate the device..

Sometimes the candle remains dry. In this case, it is necessary to draw the gas mixture into the syringe and pass it into the cylinder. After that, you should immediately try to start the device. If the reason for the long lack of response to attempts to turn on is debris that has got into the carburetor, then when removing it, there should be no hindrance to the flow of fuel into the combustion chamber. The mechanism of successful garbage collection is determined by the flow of liquid when filling the gas mixture, so you need to pour fuel with force, and then almost immediately try to start the device.

The muffler is removed. To do this, it is unscrewed and carefully removed so as not to deform the gasket that delimits it from the engine. It is necessary to try to start the mechanism without using an air filter and a muffler, which helps to exclude breakdowns in these structural elements..

In case of any damage to the walls of the cylinder, it can be concluded that it will have to be repaired by professional methods or replaced with a new one. Usually, an insufficient concentration of oil in the fuel leads to such malfunctions..

We start Stihl MS 211 C-BE

The fuel supply system in the Stihl MS 211 C-BE chainsaw is additionally equipped with a manual fuel pump, which makes it easier to start the chainsaw on a cold.

The instruction for starting this model of the Stihl chainsaw contains one additional point, which is that before starting the chainsaw on a cold one, it is necessary to pump fuel into the carburetor using a pump. Further, the instruction does not differ from starting Stihl 180 and follows the same algorithm.

Step-by-step instruction

When the brake is activated, the assembly process is much slower, so everything is also safe and more comfortable to turn on the mechanism without the use of braking equipment.

If a person is not sure of his knowledge and accuracy, then the brake, on the contrary, needs to be activated. With the correct procedure, the device will not start, the mechanism will not perform actions that are dangerous to humans..

How to start a Stihl chainsaw

All Stihl chainsaws are equipped with two-stroke engines, the cold start of which has a similar algorithm. But there are models on which additional equipment is installed that allows you to start the saw without excessive efforts. For this reason, the algorithm for starting them may differ slightly..

Let’s take a look at how to start a regular saw and how the process differs from starting a modified model..

2 diagram of a standard mechanism – how to start the saw correctly

• The ignition is switched on. To do this, you need to move the toggle switch to the desired place or move the switch.
• The swap primer usually has to be pressed more than twice. Gasoline is poured into it, after which you will have to press the device more than three times. Sometimes the chainsaw is not equipped with a primer, then you can skip this step.

The adjustment lever, which is responsible for the location of the damper, must be pulled out as far as it will go. Many chainsaws have the ability to block this element. Then it can only be moved while pressing and holding the throttle button. Some chainsaws do not have this lock, which makes them more comfortable to use. In these models, gas may not be fixed or retained when using automatic technologies.

You need to take the starter handle and jerk it with sharp movements until the ignition is heard. It is celebrated by the institution and the almost instantaneous shutdown of the motor. After that, the shutter must be pushed back to its original position, checking it until it stops. Then the starter handle jerks again until the device starts. Before carrying out this event, you need to make sure that it is this method that will help start the chainsaw. Some devices have a different ignition system. In order for the motor to work in them, you need to move the damper only by 50%, and only when the motor starts to actively work, move it completely.

If you purchased a model with a locking gas, you need to prepare in advance for the highest engine speed immediately after activating the device. When there is no fixation, the initial power is very low, so in most cases it has to be increased. If you do not take any action, then in the latter case, the saw runs for a short period of time, and then automatically stalls. If such a situation occurs, you need to start the chainsaw again..

When the device stalls constantly, you need to systematically start it up again (see what to do when the chainsaw stalls when you press the gas). After a while, the motor will pick up speed and be able to maintain active work without interruption..

For more details, see

How to start a Stihl chainsaw (Stihl MS-180) – the first start and start without a starter

Chainsaws differ slightly in design features, but in most cases the assembly principle is carried out according to two standard schemes. For many devices, the instructions contain information on the need to activate the emergency brake system before starting the activation procedure. You should first master the device of the plant and study the main ways of correcting breakdowns, then a person will have the opportunity to fully operate the device. The article will talk about how to start a chainsaw..

We start Stihl MS 211 C-BE

The fuel supply system in the Stihl MS 211 C-BE chainsaw is additionally equipped with a manual fuel pump, which makes it easier to start the chainsaw on a cold.

The instruction for starting this model of the Stihl chainsaw contains one additional point, which is that before starting the chainsaw on a cold one, it is necessary to pump fuel into the carburetor using a pump. Further, the instruction does not differ from starting Stihl 180 and follows the same algorithm.

How to start a Stihl chainsaw

All Stihl chainsaws are equipped with two-stroke engines, the cold start of which has a similar algorithm. But there are models on which additional equipment is installed that allows you to start the saw without excessive efforts. For this reason, the algorithm for starting them may differ slightly..

Let’s take a look at how to start a regular saw and how the process differs from starting a modified model..

• We start Stihl 180
• We start Stihl MS 180 C
• We start Stihl MS 211 C-BE
• What happens when the primer is pumped up, and how it helps to start the saw more efficiently?
• How to start a chainsaws with a decompression valve
• How to start the saw after a long period of inactivity
• Outcomes

How to start the saw after long periods of inactivity

I can’t start the chainsaw after a long period of inactivity. Such comments can be found on the forums dedicated to the repair and operation of saws. Let’s figure out how to start a chainsaw after a long period of inactivity..

The fact is that a successful start after a downtime, you need to take care in advance and properly prepare the saw for storage. According to the manufacturer’s instructions, before storing, it is necessary to drain the fuel from the tank, then start the engine and burn off the fuel in the fuel system..

Preparation is necessary so that during storage, the carburetor membranes do not stick together. Performing this simple operation will allow you to successfully start the saw after long-term storage..

It is much easier to start the chainsaw six months after idle time, if just before starting, through the spark plug hole, add 1 – 2 ml of the fuel mixture to the cylinder. This can be done with a syringe..

We start Stihl MS 180 C

The device of this model, in comparison with the previous one, has some differences in the trigger mechanism, but it does not carry any changes in the triggering algorithm. The fact is that the ErgoStart system is installed in the Stihl 180 C, which, due to an additional spring installed in the chainsaw starter, reduces the engine resistance when starting.

We start Stihl 180

In order to start a Stihl 180 chainsaw on a cold one, you must follow the algorithm specified by the manufacturer in the instructions for the Stihl 180 chainsaw, namely:

• Turn on the ignition and set the engine control lever to the lowest position (in this position, the air damper of the Stihl 180 carburetor blocks air from the air filter, and the throttle valve is fully open, thus the fuel mixture is enriched);
• Pull the starter handle several times until the first flash passes (the flash signals that the fuel mixture has entered the cylinder and the saw is ready to start);
• Set the control lever one position up from fully lowered (in this position, the air damper opens, and the throttle valve remains in the same position as before);
• Pull starter and start. The saw will start and run at higher revs because the throttle valve is open as much as possible. To set the damper to idle mode, you must press the gas trigger and immediately release, the tool immediately normalizes the speed.

The Stihl MS 180 chainsaw, as standard, does not have any additional devices that can facilitate starting.

Below you can see how to start a Stihl 180. The video reflects in detail all the main points, and the author’s comments allow you to understand the whole process to the smallest detail.

How to start a chainsaws with a decompression valve

Before starting a Stihl chainsaw on which a decompression valve is installed, you must turn it on. It should be noted that there is no decompression valve on the Stihl 250 saw.

After the first flash has passed, the valve will be set to normal operation, respectively, after the engine control lever is set to the open air damper position and starting continues, the decompression valve must be pressed again..

The valve operation is schematically shown in the figure below..

In fact, the valve does not make starting faster, it just simplifies the process and makes it more comfortable, because for during launch, a person will have to apply significantly less effort.

A saw with a decompression valve, whether the engine is cold or hot, must be started using the valve to relieve the cranking force of the engine. This will significantly increase the service life of the starter and reduce the number of torn laces, since it is installed on chainsaws with a large cylinder volume and, accordingly, compression..

What happens when the primer is pumped up, and how it helps to start the saw more efficiently?

At the moment of starting the saw without a primer, several movements of the starter are carried out only so that the fuel pump, under the action of an impulse from the saw crankcase, pumped fuel into the carburetor.

The pump installed in the fuel line allows in manual mode, without unnecessary movements with the starter, to pump gasoline into the carburetor. The effect of this action is obvious, the saw will start much faster..

Many owners of gasoline-powered tools mistakenly believe that a hand pump can overly pump fuel into the carburetor and, for this reason, will flood the candle. This is fundamentally wrong, since the system is capable of circulating around. Excess gasoline from the carburetor will be directed, through a dedicated hose, back to the tank.

There is no need to use a primer on a hot chainsaw, since there is enough fuel in the carburetor to start.

How to start a Stihl saw?

Not knowing how to sharpen the saw correctly or how to start it correctly forms a very negative opinion about certain saw brands. Therefore, in order to avoid a problem in using the Stihl saw, it will be enough to familiarize yourself with the basic rules of working with it..

• Chainsaw “Stihl”
• Petrol
• Butter

Working with a chainsaw begins directly with starting it. And it is at this stage that the most common problem often arises: the launch does not take place. Puzzling over how to start a Stihl saw, many run to the nearest workshops and talk about its breakdown. And if the saw is new, then they generally try to return it back to the seller. In fact, the reason is not a malfunction of the saw, but only in its features, which should be taken into account when starting.

If the saw is new, then you should not throw its instructions too far, because it describes important and main actions that cannot be neglected. You can also find other tips there. for example, how to sharpen a saw correctly. Before starting it is necessary to prepare the saw. For this, special protection is removed from the tire, and oil for the chain and gasoline for the engine are poured into special tanks, which is diluted with two-stroke oil into a kind of gasoline mixture. It is also important to set the chain tension..

On the recommendation of specialists or the same instructions, starting the chainsaw begins with activating the chain brake. Some models are equipped with a decompression valve, therefore it is recommended to press it in order to quickly start the engine of the chainsaw. The same actions are recommended to be done with the fuel pump, pressing which will significantly reduce the number of pumping. When it comes to how to sharpen the saw correctly, then it should be in a neutral state, and all the actions described should not be applied to it..

Now the combination lever is set to the cold start state, that is, first you need to activate the throttle lever, and then press the combination lever itself all the way down. When starting, the saw should be placed on a level surface, preferably on a hard floor, and the saw blade should not be in contact with the surface. The stability of the chainsaw is ensured by gripping the main handle with the left hand, and with the lower leg with the foot. Before choosing a reciprocating saw, it is important that it is equipped with additional handles for safety and ease of use..

Then slowly pull the starter rope with your free hand. When resistance is felt, the cable is pulled sharply up several times. At this time, the engine starts, but quickly turns off. This does not mean that it is already time to think about how to repair the saw. You just need to move the combined lever to the half-throttle position, that is, one position. The engine is now started using the starter rope. The lever immediately moves to its original position, and a finger briefly presses the throttle lever. Now the chainsaw can be slowly raised and started to use carefully, be sure to observe all safety measures.

How to start the saw after long periods of inactivity

I can’t start the chainsaw after a long period of inactivity. Such comments can be found on the forums dedicated to the repair and operation of saws. Let’s figure out how to start a chainsaw after a long period of inactivity..

The fact is that a successful start after downtime must be taken care of in advance and the saw should be properly prepared for storage. According to the manufacturer’s instructions, before storing, it is necessary to drain the fuel from the tank, then start the engine and burn off the fuel in the fuel system..

Preparation is necessary so that during storage, the carburetor membranes do not stick together. Performing this simple operation will allow you to successfully start the saw after long-term storage..

It is much easier to start the chainsaw six months after idle time, if just before starting, through the spark plug hole, add 1 – 2 ml of the fuel mixture to the cylinder. This can be done with a syringe..

We start Stihl 180

In order to start a Stihl 180 chainsaw on a cold one, you must follow the algorithm specified by the manufacturer in the instructions for the Stihl 180 chainsaw, namely:

• Turn on the ignition and set the engine control lever to the lowest position (in this position, the air damper of the Stihl 180 carburetor blocks air from the air filter, and the throttle valve is fully open, thus the fuel mixture is enriched);
• Pull the starter handle several times until the first flash passes (the flash signals that the fuel mixture has entered the cylinder and the saw is ready to start);
• Set the control lever one position up from fully lowered (in this position, the air damper opens, and the throttle valve remains in the same position as before);
• Pull starter and start. The saw will start and run at higher revs because the throttle valve is open as much as possible. To set the damper to idle mode, you must press the gas trigger and immediately release, the tool immediately normalizes the speed.

The Stihl MS 180 chainsaw, as standard, does not have any additional devices that can facilitate starting.

Below you can see how to start a Stihl 180. The video reflects in detail all the main points, and the author’s comments allow you to understand the whole process to the smallest detail.

Can I start without a starter?

It is impossible to start a chainsaw without a starter. In the absence of this element, there will be disturbances in the engine cooling process, since it contains the so-called “snail, which regulates the flow of cold air from the flywheel impeller to the internal combustion engine cylinder..

Fuel mixture preparation

For normal operation of the chainsaw, it is recommended to take gasoline with an octane rating of at least 90. The best option is the AI-92 brand, the use of lower-quality fuel can cause the engine to knock, reduce its productivity.

Two-stroke engine oil is required for both break-in and continuous operation. It is better to purchase brands designed for specific models of chainsaws. The proportions for preparing the fuel mixture for each saw are indicated in the operating instructions, on average it is recommended to mix at the rate of 1:33. For old domestic chainsaws, the mixture is prepared in a ratio of 1:15.

Important! Leaded fuel is used to refuel chainsaws with an engine without a catalyst. Its presence can be identified by the green gas tank cap, for models with a catalyst, unleaded gasoline is required.

Chainsaw and two-stroke engine devices

By design, all models of modern chainsaws are a mechanism that is started by an internal combustion engine. This is usually a single cylinder, two-stroke version that lacks the classic gearbox. Its function is performed by a single-stage chain transmission, which drives the saw headset. The main components of the chainsaw design:

• membrane type carburetor;
• ignition;
• fuel system;
• starter;
• air purification unit;
• chain and bus;
• chain brake (contact and inertial);
• tension mechanism;
• Lubrication system.

Figure 1 – External device of the chainsaw

Chainsaws are equipped with a centrifugal clutch that engages automatically depending on the engine speed. With sufficient power, the special elements are pressed against the inside of the drum, setting the drive sprocket in motion. The advantage of such a mechanism is that when the saw jams in the cut, the clutch begins to slip, reducing the risk of breakage of internal mechanisms.

Important! The internal combustion engine in chainsaws has a maximum speed of up to 13.5 thousand per minute. The quality of its work directly depends on the fuel mixture, oil.

Stihl 180 saw setting algorithm

If you are faced with the question of how to start a Stihl chainsaw, then this process can be considered using the model 180 as an example. In order to carry out work on a cold one, you must turn on the ignition and set the engine control lever to the lower position. In this case, the carburetor flap will block the air from the filter, and the throttle will be open, so the fuel mixture will be enriched.

The starter handle must be pulled several times until the first flash occurs. This will indicate that the mixture has entered the cylinder and the equipment is ready for institution. Before starting the Stihl chainsaw, you must set the control lever one position up. In this case, the choke will open, while the throttle will remain in the same position..

The starter must be pulled and started. The tool will run at increased speed and the throttle valve will be open. To set the latter to idle, you must pull the gas trigger and release it. In this case, the tool should start working normally. On the described model of the chainsaw there are no additional devices that would make it easier to start.

Checking the oil supply

To achieve the sliding of the chain on the headset, a special oil tank is located in the engine crankcase – it supplies oil to the tire. Its work is controlled by a special pump, which starts when the engine speed increases. To check the supply and operation of the lubrication process, you need to remove the side protection of the tire, start the tool. If oil enters the headset and decreases in the reservoir (check with a dipstick), then no action is required. If the amount of mixture is insufficient, it is recommended to clean or replace the filter, and then adjust the flow.

Stihl 250 chainsaw review

You can buy the 250 model at a price of 29,542 rubles. This equipment is a semi-professional model with a 40cm tire. Power is 3.1 liters. from. or 2.3 kW. Fuel tank capacity is 0.47 l.

Quite often, consumers before buying are wondering how to start a Stihl 250 chainsaw. This was discussed above. However, this information is not the only one that should be read before using the model. Other features include:

• single-lever control;
• the presence of a compensator;
• anti-vibration system;
• side chain tensioner.

By purchasing this model, you will be able to carry out its quick refueling. This feature is realized by the lid, which has a patented design. The operator, when working with the equipment, will have reliable hand protection. Consumers especially highlight the notch bumper, as well as the chain, which guarantees high-quality and fast cutting of wood..

Stihl 180 saw setting algorithm

If you are faced with the question of how to start a Stihl chainsaw, then this process can be considered using the model 180 as an example. In order to carry out work on a cold one, you must turn on the ignition and set the engine control lever to the lower position. In this case, the carburetor flap will block the air from the filter, and the throttle will be open, so the fuel mixture will be enriched.

The starter handle must be pulled several times until the first flash occurs. This will indicate that the mixture has entered the cylinder and the equipment is ready for institution. Before starting the Stihl chainsaw, you must set the control lever one position up. In this case, the air damper will open, while the throttle will remain in the same position..

The starter must be pulled and started. The tool will run at increased speed and the throttle valve will be open. To set the latter in idle speed, you must use the gas trigger and release it. In this case, the tool should start working normally. On the described model of the chainsaw there are no additional devices that would make it easier to start.

Stihl 250 chainsaw review

You can buy the 250 model at a price of 29,542 rubles. This equipment is a semi-professional model with a 40 cm tire. Power is 3.1 liters. from. or 2.3 kW. Fuel tank capacity is 0.47 l.

Quite often, consumers before buying are wondering how to start a Stihl 250 chainsaw. This was discussed above. However, this information is not the only one that should be read before using the model. Among other features, it should be highlighted:

• single-lever control;
• the presence of a compensator;
• anti-vibration system;
• side chain tensioner.

By purchasing this model, you will be able to carry out its quick refueling. This feature is realized by the lid, which has a patented design. The operator, when working with the equipment, will have reliable hand protection. Consumers especially highlight the spike bumper, as well as the chain, which guarantees high-quality and fast cutting of wood..

We start the saw brand MS 211 C-BE

If you, too, were among those consumers who thought about the question of how to start a Stihl chainsaw, then as an example, consider another model that was mentioned above. In it, the feed system is equipped with a hand pump, which makes it easier to start the saw on a cold.

The instruction contains an additional paragraph, which indicates that before starting with the pump, it is necessary to pump fuel into the carburetor. Next, you should proceed according to the principle that was described for the 180 model.

How to start a Stihl chainsaw: starting process and overview

All chainsaws from the manufacturer “Stihl” have two-stroke engines. Their cold start is carried out according to a similar algorithm. However, on sale you can find models on which there is additional equipment, with its help you can start the saw without much effort. For this reason, the starting method may differ..

Setting up the saw after winter

Before storing it, you should drain the fuel, and then start the engine and burn off the fuel that remains in the system. Preparation is necessary so that the membranes do not stick together during storage. This simple operation will allow you to start the saw after winter. If you still do not know how to properly start the Stihl 180 chainsaw, then you should know that it will be easier to do this if you add 2 ml of fuel mixture to the cylinder through the spark plug hole before starting. This can be done with a syringe..

Tips for starting a saw MS 180 C

This device, in comparison with the previous one, has some differences in the trigger mechanism. However, there will be no changes in the startup algorithm. The equipment described has a system that uses a spring in the saw starter to reduce the resistance of the motor..

Chainsaw MC 180 review

This model of equipment costs 11,490 rubles. It is a household tool that will help you cope with work at a summer cottage. With the help of the machine, you can get rid of unnecessary twigs and cut down small trees. The control is single-lever, and due to its low weight, it is very comfortable to work with the unit.

The consumer should be aware not only of how to start a Stihl ms 180 chainsaw, but also of the technical characteristics. Among others, the 35-cm tire should be distinguished, as well as the engine, the volume of which is 31.8 cm 3. The volume of the oil tank is 0.15 liters. The equipment weighs 3.9 kg. The power of the model is 2 liters. from. Fuel tank capacity is 0.25 l.