Filter check
Another common condition that the trimmer won’t start is if there is a blockage in the filter area. To confirm the guess, it is enough to dismantle the indicated block and try to start the unit without it. If the trimmer engine starts, you will most likely need to replace the air filter or at least thoroughly purge the old one. If there is heavy dirt on the surface of the filter element, a new mesh must be used. When resorting to such actions, do not leave the suction pipe completely without a filter. After all, haste in this case can lead to the need to repair the entire piston group of the engine unit.
Trimmer ON cold does not start well, what to do?
For even more information on repair and tool selection on our website www.Looktool.Ru visit we are glad to everyone.
After a few jerks, it will start and stall, which is normal. Petrol Trimmer Start Crank Cold Trim Bad start. Move the choke to the working position, start the tool again and start working.
Diagnostics of the candle channel
What to do if the used fuel mixture is in good order, but the petrol trimmer still won’t start? The reasons for the failure of the mechanism may lie in the excessive wetting of the candle channel. To diagnose and fix the problem, you must do the following:
- Unscrew the candle. Cold trimmer does not start well, what to do. Wipe it thoroughly and then dry it.
- Drain excess fuel in the chamber through the appropriate plug hole.
- Clean the old plug if there is carbon deposits on its surface. To cope with the task will allow the use of an ordinary ladies’ nail file or a file.
- When installing the element in place, set a gap of 1 mm. To check the parameter, it is enough to place any coin in the gap.
- Assemble the functional block back.
- Try to start the trimmer.
It is recommended to dry the candle channel for at least half an hour. However, in no case should you resort to calcining its elements. After all, heating the spark plug can lead to its final damage. What to do if the maintenance of the functional unit was carried out in accordance with the above recommendations, but the trimmer does not start, there is a spark? In this case, it is worth treating the threaded connection with gasoline. The latter does not need to be abundantly impregnated with fuel. Petrol Trimmer Start Crank Cold Trim Bad start. It should only be slightly damp. Resorting to such actions should be taken to ensure ignition. After all, no matter how strong the spark the candle gives, there will simply be nothing to ignite in an absolutely dry chamber.
Outlet duct diagnostics
Stable trimmer performance can be compromised by build-up of dirt in the exhaust duct or blockage in the muffler mesh. This problem most often occurs during the operation of older generation trimmer models. The gasoline trimmer, like all things, if the gasoline trimmer does not start well or. The issue is being solved by dismantling the anti-spark grid and cleaning it.
Trimmer Starts poorly on cold
What to do when the petrol trimmers DO NOT start?
The gasoline trimmer is a surprisingly necessary tool with which you can mow Not only a small clearing in front of the house, but also a whole large lawn. Unfortunately, there is nothing endless in this world, and therefore you may be faced with the fact that petrol trimmers DO NOT start.
Why does the trimmer start badly on cold
reasons
There are not only situations when the petrol trimmers DO NOT start, but there are cases when after starting they work for a couple of seconds and immediately stall. Inspect the spark plug again: if it is “thrown”, and this situation repeats even after wiping and drying it, go to the “revision” of the air filter.
Most likely, it is completely oily and needs to be replaced. If everything is fine with the filter, it may be that the ignition coil is out of order.
In the case when the petrol trimmers DO NOT start, and you have done all of the above, the muffler may be clogged. Trimmer ON cold does not start well, Why does the trimmer not start? Starts up. I. It must be dismantled, burned on burners, after which all carbon deposits can be easily shaken out.
reasons
There are not only situations when the petrol trimmers DO NOT start, but there are cases when, after starting, they work for a couple of seconds and immediately stall. Inspect the spark plug again: if it is “thrown”, and this situation repeats even after wiping and drying it, go to the “revision” of the air filter.
Most likely, it is completely oily and needs to be replaced. If everything is fine with the filter, it may be that the ignition coil is out of order.
In the case when the petrol trimmers DO NOT start, and you have done all of the above, the muffler may be clogged. It must be dismantled, burned on burners, after which all carbon deposits can be easily shaken out.
Perform cold starts correctly!
Often gasoline trimmers DO NOT start after they are Trying to “put into operation” after long storage. Launch failures in this case are often caused by incorrect user actions.
If you are faced with exactly this phenomenon, then during a cold start you need to close the damper, and then pump a small amount of the fuel mixture into the carburetor. Then pull the starter handle until you feel resistance, then start the trimmer with a sharp and energetic movement.
Diagnostics of the candle channel. Petrol Trimmer Won’t Start? Elitech T750 Reasons and Solutions
In general, such a conversation should start with the fact that after buying a garden gasoline tool, it would be better to first familiarize yourself with the instructions attached to it. Then many problems could be avoided. But since this happened, the gasoline trimmer does not start, then you need to look for sources of inoperability. And in this article we will consider the main reasons why the trimmer does not start on the example of the Elitech T750 model, as well as we will tell you general recommendations for using such a tool.
You should start with the banal! Let’s figure out how to properly start a gasoline trimmer. It may be that the reason lies precisely here.
First you need to bring the red toggle switch on the trim bar to the “I” position. This means turning on the power. Then you need to switch the fuel supply lever to the carburetor and use the fuel “suction” button (similar to a pipette, located in the carburetor). This is necessary to supply gasoline to the engine. Return the fuel delivery lever to its original position. Finally, pull the starter handle sharply towards you. The trimmer should work. Try it several times if it doesn’t work the first time. If, after such manipulations, the situation has risen and the gasoline trimmer does NOT start, then you should first inspect it yourself before you take it to the service center. There are two main reasons your garden trimmer won’t start:
- Power circuit breakdown.
- Sun fuel.
- Let’s start with the ignition problems. In most cases, it is caused by the need to change the spark plug in the engine. This is done like this:
- First of all, we have to take care of the safety measures, making sure the trimmer is disabled. We bring the above toggle switch to the “STOP” position.
- Then we remove the rubber protection from the candle and the wiring terminals. Using a special spark plug wrench, we unscrew the spark plug and replace it.
- After that, we assemble the device and carry out the above procedure for starting the trimmer.
The second reason garden tools don’t work is because they run out of fuel. On the Elinech T750, the fuel tank is located near the engine, but on most trimmers it is located there. We unscrew the cap from the tank and fill it with gasoline (the most optimal variant is AI-92, it is inexpensive and does NOT clog the carburetor like the AI-76). Do not forget to add special oil for engines to the tank, 50 grams is enough for the gas tank, without it the engine will start to “sneeze” and will quickly become unusable. Then we close the tank with a cap, wipe the trimmer surface and our hands with a dry cloth. We also do the above manipulations to turn on the garden tool.
If the petrol trimmer does not start as before, then it makes sense to have it repaired. And the reason for this decision is simple. if you DO NOT have the appropriate skills, equipment repair is almost impossible.
In order for the tool to serve as long as possible and NOT to have such problems, you should first of all read the instruction manual for the trimmer. Also, pay special attention to the engine running time in the trimmer. take a short break every 15 minutes of work and, finally, properly care for the tool, wipe it after work, grease it with graphite grease. Observing such simple rules, you can significantly increase the service life of the tool and it is quite possible that you do NOT have to look for reasons why the gasoline trimmer does not start.
30,294 total views, 13 views today
Filter check
Another common condition that the trimmer won’t start is if there is a blockage in the filter area. To confirm the guess, it is enough to dismantle the indicated block and try to start the unit without it. If the trimmer engine starts, you will most likely need to replace the air filter or at least thoroughly purge the old one. If there is heavy dirt on the surface of the filter element, a new mesh must be used. When resorting to such actions, do not leave the suction pipe completely without a filter. After all, haste in this case can lead to the need to repair the entire piston group of the engine unit.
Trimmer won’t start. Why?
A petrol trimmer is a surprisingly useful thing that can be used to tidy up not only a miniature lawn in the backyard of the house, but also mow a lawn of considerable size. But, like all things in this world, he has the property of a rebellion of salesmen. In this article we will try to figure out what to do in cases where the trimmer refuses to work.
Checking the fuel mixture
Let’s say your trimmer won’t start. In this case, the first step is to check whether there is enough fuel in the tank, and also to assess the quality of the fuel mixture. It is necessary to refuel the motorized unit with exclusively high-quality gasoline. It is recommended to use fuel, the grade of which is NOT lower than AI-95. Filling the trimmer with fuel of unknown origin not purchased from a gas station can cause frequent tool malfunctions. This can cause damage to the piston-cylinder system. Repair in this case often exceeds the cost of the device itself.
Why won’t the petrol trimmer start? Improper preparation of the fuel mixture, which consists of oil and gasoline, can also lead to this. The proportions in which these components are connected are indicated by the manufacturers in the trimmer instruction manual. Preparing a fuel mixture is highly discouraged in large volumes, that is, for the future. Petrol Trimmer Won’t Start? Reasons and solutions based on the example of the Elitech T750. Indeed, with long-term savings, there is a loss of the determining properties of the substance. Therefore, if the trimmer does not start, it is worth draining the old fuel and using a freshly prepared fuel mixture.
Troubleshooting strategy
Where to start troubleshooting if the trimmer won’t start? In situations where the tool stalls immediately after starting, it is worth inspecting the following components of the unit:
- Fuel tank;
- Spark plug;
- Fuel and air filter;
- Outlet channel;
- Breather.
It is the breakdown of the above locations that most often leads to the fact that the trimmer does not start well. What to do when the fuel was definitely normal, there is a spark, but the petrol trimmer will not start? Let’s look at how to eliminate such troubles.
What to do if the used fuel mixture is in good order, but the petrol trimmer still won’t start? The reasons for the failure of the mechanism may lie in the excessive wetting of the candle channel. To diagnose and fix the problem, you must do the following:
- Unscrew the candle. Wipe it thoroughly and then dry it.
- Drain excess fuel in the chamber through the appropriate plug hole.
- Clean the old plug if there is carbon deposits on its surface. To cope with the task will allow the use of an ordinary ladies’ nail file or a file.
- When installing the element in place, set a gap of 1 mm. To check the parameter, it is enough to place any coin in the gap.
- Assemble the functional block back.
- Try to start the trimmer.
It is recommended to dry the candle channel for at least half an hour. However, in no case should you resort to calcining its elements. After all, heating the spark plug can lead to its final damage. What to do if the maintenance of the functional unit was carried out in accordance with the above recommendations, but the trimmer does not start, there is a spark? In this case, it is worth treating the threaded connection with gasoline. The latter does not need to be abundantly impregnated with fuel. It should only be slightly damp. Resorting to such actions should be taken to ensure ignition. After all, no matter how strong the spark the candle gives, there will simply be nothing to ignite in an absolutely dry chamber.
Trimmer won’t start Petrol Reasons floods candles
Why won’t the petrol trimmer start? Causes and their elimination
Recently, the gasoline trimmer has acquired the status of one of the main tools in the arsenal of summer residents. And this is not surprising, because a motorized scythe allows you to quickly put your personal plot in order. However, it sometimes happens that the trimmer will not start hot or even cold. Why the petrol trimmer won’t start. The reasons why the petrol trimmer stopped starting can be different, therefore. In such situations, you have to independently determine the cause of the malfunction. Let’s figure out what to do if the trimmer won’t start. The reasons that most often lead to such troubles will be discussed below.
Trimmer Will not start after winter
How to be in such a situation? Do NOT worry and panic. This is a very common problem that can be solved in just 3-4 minutes. Firstly, if last year’s fuel remains in the gas tank, then it must be drained. Gasoline loses its octave properties after 2 weeks of inactivity. Secondly, the lawn mower starts after a long stagnation in a slightly different way. First you need to open the throttle and pump a little fuel mixture into the carburetor, then pull the handle until you feel a little resistance. After that you can start the trimmer.