How To Put A Fishing Line On A Stihl Trimmer Video

How To Put A Fishing Line On A Stihl Trimmer Video

Guaranteed production of a factory trimmer refill will inevitably require replacing the fishing line. Having a very rough idea of ​​how to fill the fishing line into the reel of the trimmer yourself, beginners are reluctant to take up this matter. However, with some skills, mastering this simple science does not present any difficulties, and the similar instruction presented below will facilitate this process as much as possible.

Preliminary preparation

First of all, for winding fishing line it is required to remove the reel (bobbin, spool) from the trimmer. specific actions will depend on the complexity of the configuration and the type of product itself:

  • Small electric trimmers with a working arrangement of the engine and the coil in the lower part, as a rule, have side keys on both sides of the bobbin. By pressing them simultaneously, the upper part of the reel, together with the internal contents for winding the fishing line, is disconnected, while the lower one remains on the trimmer. It is advisable to disassemble the bobbin on an even smooth place so that the spring included in the design does not pop out and is not lost;
  • electric and gasoline trimmers with a curved bar without the possibility of installing a knife, as a rule, have coils with a special wing: in such designs, you should hold the spool in one position with one hand and rotate the locking reel on the wing nut with the other counterclockwise. After disconnecting the nut, the entire reel is removed.
  • electric and petrol trimmers with the possibility of installing the knife on a straight bar (for example, Stihl trimmers) have a hole under the bobbin. For the motion of the rod to be stationary, a screwdriver or other suitable object is inserted into this hole and with a slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bobbin is fixed. After that, the coil body scrolls clockwise (with the left thread) and is removed from the trimmer.

For the second and third cases, the coils, depending on the design, are disassembled in various ways. In bobbins with a lamb, a lamb is twisted, in coils with latches, latches-clamps are pressed and one part of the coil is released from the other. If the halves of the spool are threaded, it is enough to turn them by hand in opposite directions until completely unscrewed.

We carry out winding fishing line

Slowly completed disassembling the spool of the spool without losing its spare parts allows you to go to the main task. winding the fishing line into the reel. Technological features of the design of the spool and the number of working antennae determine the sequence of actions.

Coil with one working antenna

The simplest option and a simple sequence of actions:

  1. The dimensions of the bobbin and the length of the original factory winding determine the recommended fishing line length for winding. 2. 5 m.
  2. One end of the fishing line is inserted into the fixing technological hole located inside the spool.
  3. The fishing line is wound on the drum in the reverse direction of rotation of the spool in the trimmer product direction. as a rule, on the inner side of the bobbin an arrow indicates which side the winding is carried out.
  4. A small area of ​​fishing line is left free to bring it out. it is fixed in a specialized groove on the inside of the reel, designed to hold the winding when assembling the spool in working condition.
  5. The left end of the line is passed through the hole on the outside of the bobbin.
  6. The bobbin halves are assembled and put on the trimmer bar.

Coil with two working antennae

In this type of spools, you should determine the number of grooves for winding fishing line lying on the inside of the reel:

  • one groove. both antennae are wound together along one groove;
  • two grooves. each antennae is wound on an individual groove.

In both cases, a 2-3-meter-long fishing line is taken. In single-groove reels, the fishing line is pulled into the through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the side of the bar. the correct direction of winding is usually indicated inside the arrow. In the presence of fixing grooves, the ends of the fishing line are threaded into them or held by the fingers of their free hands, threaded into the through hole of the outer half of the bobbin, the spool is closed and attached to the bar of the trimmer.

The difference between winding fishing line in two-groove reels is that initially a piece of fishing line 2-5 m long is folded in half (to determine the middle bend), and the bend loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each in its own groove, the fixation of the antennae and the reel assembly is similar to the one-groove variant discussed above.

The first implementation of this procedure may seem long and rather laborious, but with time and experience this task will be solved much faster and easier.

The video below will clearly show how to put the fishing line into the coil of the trimmer and wrap it correctly. this operation is not complicated and with some patience will surely succeed:

Automatic reeling of fishing line

There is a variety of coils in which the automatic mechanism coils on its own. from the user it is enough just to properly fill the line. The fishing line is passed through the hole on the inside of the case, its antennae without winding is passed through the hole on the external case, the bobbin is assembled, and when the winding button is rotated, the line inside is wound up independently. In such a spool, it is impossible to make the winding incorrectly: the mechanism itself will determine the correct direction, since it can only turn in one direction.

Read more:  Trimmer Choosing.

Owners of private homes know how necessary this type of tool is, as a trimmer. It can be gasoline and electric, but they differ in the design of power units. To cut grass in areas where there are stones, trees and other obstructing objects, a fishing line is used as a cutting device. This consumable wears out during application, so how to wind the trimmer coil, we will consider in detail in the material.

What you need to know about fishing line for trimmer

A fishing line is a consumable that consists of nylon and serves as a cutting device. By means of this equipment, grass mowing occurs, which is ensured by rotating the tool head with high frequency. This material has a different thickness, which depends on its use on the corresponding tools, low-power electric (from 1 to 1.6 mm), electric from 500 W (2-2.4 mm) and gas trimmers with lawn mowers (from 2.4 to 3 , 2 mm).

The more powerful the tool, the correspondingly thicker the cutting tool should be. This affects not only the quality of the grass mowing, but also the life of the material. If you are wondering how to wind the trimmer coil, then it’s time to change the reload tool. With the onset of spring, this issue becomes more and more popular, so it’s time to understand the step-by-step instructions for replacing the fishing line in the trimmer coil.

How to remove the reel from the trimmer and remove the fishing line

Initially, before you put fishing line in the trimmer coil, you need to remove it from there. A coil or pickup is a device that is located inside the mowing head, bobbin or drum. The heads come in different types (depending on the manufacturers), however, the principle of replacing fishing line on the reel is the same for everyone. First of all, we will figure out how to remove the head from the tool, as well as how to get the drum and fishing line out of it.

The instruction on how to unwind the manual head on the trimmer has the following form:

  1. Turn the tool upside down and, if necessary, clean it from contamination. Use two fingers of one hand to hold the cover latches (on the mowing head), which are located symmetrically to each other. After lightly pressing them inward, remove the protective cover from the drum
  2. Next, the fishing reel should be removed from the drum shaft. It is mounted on a shaft without fasteners, therefore it is dismantled with one hand
  3. The main part of the drum is fixed with a screw, which must be unscrewed with a screwdriver with the appropriate tip or bit
  4. To unscrew it is necessary to hold the base of the drum with one hand, and the second to perform unscrewing with a screwdriver counterclockwise
  5. After that, you can proceed to dismantle. To do this, you do not need to pull it with all its strength, but slightly swaying to the sides, slowly disengage from the metal shaft on which the drum is mounted
  6. When reinstalling, put the head into the slots of the tetrahedral shape

This process is not difficult, and as you know, dismantling the entire head is not necessary if you know how the replacement is performed. When dismantling, consider the following nuances:

  • Periodically removing the head is recommended to prevent corrosion of the threaded connection. If you never unscrew the screw, then if necessary, it will be difficult and even sometimes impossible
  • If the screw has a four-sided bore of the head, then a screwdriver or bits of the appropriate size should be selected for twisting to prevent the faces from licking on the head
  • When assembling the installation, treat the threaded seat with lubricants, for example, solid oil or machine oil
  • If the faces on the screw are licked, then you can use special clamping tongs to unscrew it
  • There are drums that do not require pre-disassembly. To dismantle them, grasp it and turn it clockwise in the opposite direction

Video: How To Put A Fishing Line On A Stihl Trimmer Video


Knowing how to disassemble the drum, you should continue to clarify the process of replacing the trimmer fishing line. The video below shows a detailed process on how to open the trimmer coil and disassemble it.

How does a head with a fishing line on a lawn mower why do you need to know the principle of operation

Depending on the manufacturer, the heads differ structurally not only externally but also internally. Most drums have a clamping spring inside (semi-automatic and automatic). Above is an instruction on how to disassemble a trimmer head without a spring, i.e. on a manual type head. The principle of dismantling a semi-automatic head with a spring inside is almost identical to the above described instructions.

The principle of operation of the semi-automatic trimmer coil is as follows:

  1. Inside the head is a coil that is seated on the slots, preventing its free movement
  2. A spring acts on the coil, which presses it against the slots in the cover structure
  3. A line is wound around the tip, the length of which depends on the tool itself. Usually this length is from 1 to 4 meters
  4. During the execution of the work, if it is necessary to increase the length of the fishing line, the protruding part of the drum is clamped, whereby it disengages from the slots. In this case, the fishing line is wound off the drum, increasing in length
  5. After releasing the required amount of fishing line, you should release the pressing, and continue the work of cutting the grass

The advantage of a fishing line tool is that this consumable item does not require sharpening compared to metal discs. In addition, if a stone or tree comes across a path, the fishing line simply comes off, without adversely affecting the gearbox and the tool motor, as is the case with metal cutting discs.

Knowing the design and arrangement of the types of mowing or trimmer heads, it is necessary to proceed to consider the process of refueling fishing line into the trimmer coil. Indeed, it is this moment that causes the majority of special tool owners difficulties.

Instructions with a step-by-step description of how to wind the trimmer coil and lawn mowers

In order not to be mistaken with the choice of a suitable fishing line for your tool, you should first disassemble the head, and look at the side wall of the reel. This information is usually presented on a tip that will not allow you to make a mistake with the use of appropriate equipment.

Read more:  Which Gasoline Is Suitable For Stihl Trimmer

If the information on the reel about what diameter the fishing line can be refueled, then this information can be clarified in the instructions. Having decided on the thickness or diameter of the snap, it remains to figure out how to charge it. There are two ways to do this, but not all are applicable. We will consider both methods in detail, and depending on which models of lawn mowers and trimmers you use, you decide on your own which option is suitable.

Method 1. how to wind the fishing line correctly or put it on a reel and choose the required length

To implement this method, you will need to pre-prepare a fishing line of the required length (usually up to 4 meters). It all depends on the thickness of the equipment used, as well as the design of the coil. There is a simple way to find out the required amount of fishing line, the refueling of which will be needed to charge the coil. To do this, the equipment should be wound inside the coil until it is equal to the side protrusions. Equipment should not go beyond these extreme protrusions.

The thicker the equipment used, the less its length will be needed and vice versa, the thinner, the longer the segment will be needed.

The instruction on how to properly rig the equipment into the tip of the trimmer or lawn mowers is as follows:

  1. To begin with, a piece of fishing line that has been prepared to install in a reel must be folded in half. In this case, one edge should protrude 10-15 cm more than the second
  2. After that, the second end is taken from the other side, and doubled up. Move to it so that the measured protrusion of 15 cm is preserved
  3. There is a slot in the inner baffle of the coil into which the resulting loop should be inserted. The slot in the wall is shown in the photo below.
  4. Next, we find out the direction of winding the fishing line. If you wind the equipment in the wrong direction, then it will not function correctly, and you will need to redo the work. To insert the fishing line, and wrap it in the right direction, you should inspect the surface of the reel. It should indicate the direction of winding (in 99% of cases, this direction is indicated). How the direction indicator on the coil looks, shown in the photo below
  5. This arrow pointer can also be labeled, as in the example above, “WIND LINE”, which means the direction of winding. If the pointer is not on the coil, then look at the head. On the head there is a direction of its rotation, and in order to properly wind the line, you should wind it on the drum in the opposite direction to the indication of the arrow pointer. So, if the arrow is on tip, then you need to wind in the specified direction, and if it is not there, then you should wind against the direction of the arrow on the surface of the head
  6. Having decided on the direction of rotation, you should proceed to winding. Each end should lead in its groove. If there is no separator, then fit the equipment in the appropriate distribution order
  7. When almost all the fishing line is wound on a reel, you need to do the following. place a short part in the hole of the tip side wall, the protrusion of which should be up to 10-15 cm, and then similarly do the procedure with the other end, placing it in the hole on the parallel side
  8. We insert the reel into the head, previously skipping the ends of the fishing line into the holes of the drum
  9. We put the drum in place and pulling the ends of the fishing line, we disengage them from the temporary clamps in the reel wall. After that, you can put on the cover until the latch
  10. On this, the process of how to replace the fishing line on the trimmer is completed, and if necessary, you can cut only the ends (if their length does not suit), and install the drum assembled on the instrument

With how to put the drum in place, no difficulties arise. There is a second way, how to charge mowing equipment in a lawn mowing ground. What is the difference, and how is the second method of refueling fishing line on the lawn mowing coil carried out, we will find out in detail.

Method 2. how to properly put fishing line on a lawn mowing coil with a photo description and video

The second method differs from the first in that not a single piece of equipment is charged into the coil, but segments of two parts. This method is used by manufacturers, and it is also suitable for those who have leftover material. The principle of how to insert two pieces of fishing line into the tip of the lawn mowing is the same with the first method, and to make sure of this, below is a detailed instruction:

  1. There are two equal lengths of material that can be used.
  2. One piece is taken, and the edge is bent in the form of a clamping bracket or hook, with the help of which the fishing line will be fixed
  3. Inside the coil there are holes in the form of a bracket for fixing, which are there for a reason. If they are not, then the second option will not work. The appearance of these brackets is shown in the photo below. Each bracket is in its own half.
  4. Brace fishing line should catch on the bracket, and make it winding in the direction of the arrow
  5. The tooling is wound up until a segment of 10-15 cm remains, which is fixed in the corresponding hole on the side of the tip
  6. Similarly, manipulations with the second end of the fishing line
  7. The tabs start up in the holes of the head, and then, removing the snap-in from the temporary fasteners in the coil, a cover with latches is installed

The above instructions on how to install a fishing line in a lawn mower will help not only correctly, but also quickly perform the replacement procedure. Assembly of the trimmer coil, as mentioned above, can be performed without removing the head, but in this case you will need to conveniently fix the tool. Video instruction is presented below.

Read more:  Grass Trimmer How to Fill a Fishing Line

Tips and tricks on how to wind a fishing line and what you need to know

There are some useful tips and tricks that will be useful to learn not only for beginners, but also for experienced mowers. These tips will help prevent negative consequences in the form of injuries and improper functioning of the mechanism. These recommendations read as follows:

  1. Install the cover until it clicks. over, this is 2 or more clicks, which depends on the number of clips. If one lock does not snap in, then when you start the tool, the drum may pop out and injure a person
  2. Do not wrap the fishing line with a strong pulling it, as well as in an amount greater than you can insert it into place. It’s better not to wring the snap than it will be more, as this will lead to negative consequences in the form of the inability to unwind it if necessary
  3. If you do not own the tool with two leads of the fishing line, but with one (usually these are low-power units), then the winding process is carried out in the same sequence as described above, only with the difference in the absence of a middle rim between the extreme bases of the coil
  4. After replacing the material, it is necessary to first check the operability of the tool, and only then proceed to mowing the grass. If you do not perform a preliminary check, then the forest can unwind, and injure a person

The result of the work done is the following. after the replacement of new material, the usual one is enough for an area of ​​up to 600 square meters, but taking into account the presence of a reinforcing layer on the fishing line. Conventional nylon materials serve less, which is important to consider when working. Do not try to mow thick-stalked grass with fishing line, as there are special metal discs or knives for this.

A gasoline or electric trimmer is an indispensable assistant in the arsenal of a modern summer resident or the owner of his own house.

Thanks to these garden devices, you can easily mow down even a large garden plot. After acquiring this tool and doing a few tricks, many people think about how to wrap the fishing line on the trimmer coil correctly. For an inexperienced user, the first operation to replace it will seem problematic and time-consuming, since developers often do not fully reflect the instructions for replacing the fishing line in the instruction manual.

Preparation for winding fishing line

Prior to the winding process, it is necessary to remove the reel with fishing line from the housing. Depending on the manufacturer, power and type (electric or gasoline), there are three structural types of trimmers:

    Compact electric trimmers.

Straight Bar Trimmer

In such a model, it is possible to install a knife. Removing the coil in such models is done by means of two keys recessed into the coil body. To install the trimmer knife, it is necessary to combine the hole of the bobbin and the rod, and then insert the device in the form of a steel pin (screwdriver, iron bar). After fixing the coil, it is easy to unscrew the housing by hand clockwise.

Winding fishing line on trimmer

The measured and accurate dismantling of the spool from the spit reel makes it possible to go directly to the winding of the fishing line. The design features of the head, the number and location of the fixing holes dictate the sequence of actions when performing this operation, and also determine the methods used. Today, there are several varieties of coils, depending on the number of antenna line fishing line and methods for refueling it:

  1. Trimmer head with one working antennae;
  2. A bobbin with two antennae fishing line;
  3. Auto winding reel.

Single-Barrel Trimmer Coil

Single-mustache lawn mowing coil

Many owners and specialists note the simplicity of operation and refueling reels with one mustache. Depending on the manufacturer, the length of the fishing line can vary from 2 to 5 meters. The end of the line is inserted into the head in a special technological groove or hole, and winding is made in the direction opposite to the working rotation of the bobbin. Most coils on the outside of the case have marks in the form of arrows that indicate the direction of movement of the trimmer bobbin.

After winding, you need to leave a free end of 15-30 cm to enhance the centrifugal force, which is crucial when removing the trimmer line in automatic and semi-automatic reels. Pass the left end through the working hole of the coil and assemble the head.

Double Antenna Trimmer

Two groove head

After removing the spool from the coil body, we determine the number of streams for winding fishing line (1 or 2). There is no fundamental difference between the reels with one and two grooves, but with careless refueling in the twin groove, there are problems with operation. In view of the likelihood of weaving adjacent tool strings, a situation may arise when it is impossible to remove new ones after wear of the working antennae.

Regardless of the number of streams for refueling, a fishing line from 1.5 to 3 meters long is taken. Winding must be done in the direction opposite to the rotation of the head, since winding in the direction of travel will cause the line to not be removed from the reel. After the fishing line is tucked into the trimmer coil, free ends (15-30 cm) are threaded through special holes. Next, we collect the head in the reverse disassembly order and check the performance. Do not worry if the ends of the two antennae are very different in size, because when you start the trimmer, the knife installed on the guard will cut off the excess.

Trimmer head with automatic threading

Types of Trimmer Heads

In some models available on the market, a reel with an automatic winding mechanism is installed. It is enough for the owner to correctly fill and fix the ends in the head, and the tool itself will perform the winding operation when it is switched on in the operating mode. It is almost impossible to wind a fishing line into a trimmer with such a head, since the coil independently determines the position of the antennae. The advantages of the automatic trimmer head include the ease of refueling the fishing line, and the disadvantages are frequent breakdowns of the mechanism due to the complexity of the design and high cost.