How to put a line on a trimmer

How to change the line on the trimmer

Below we have provided step-by-step instructions for replacing the trimmer thread.

The first thing to do is to unplug the tool and turn off the engine. Then you need to remove the trimmer head. This can be done using a simple screwdriver and dropping it into the hole of the gearbox to prevent the shaft from turning. And then just unscrew

They are usually unscrewed in a clockwise direction, but different models have different mechanisms, so it may have to be turned in the opposite direction. But if suddenly, for some reason, you cannot figure it out, then we strongly recommend that you refer to the user manual to understand how to disconnect it.

Second. After removing the mowing head, open it. This can be done by means of clamps that are located opposite each other. By pressing on them, you can remove the head cover, and then pull out the spool on which the line is wound. By pulling it out, you can determine what type it belongs to. There are bobbins one-piece and two-piece

We analyze how to thread the line into the trimmer spool in two versions

So, there is only one option. we load the line into a single-section reel. The prepared piece of thread is folded in half and pushed into the spool. Then, we begin to wind both ends in the same direction, which will be indicated by the arrow on the spool. At the end of winding, do not forget to make sure that different ends of the thread are looking in different directions.

Option two. winding the line with a two-piece reel. The pre-prepared thread is divided into two parts, and its ends must be fixed: this must be done by placing them in special fasteners

Winding is carried out, as in the first case, along the arrow indicated on the spool. Both segments should be wound so that they do not cross. Further, the ends of the thread should be fixed in the grooves and divorced on opposite sides.

The spring is then inserted into the reel and the whole thing is placed in the mowing head. When placing the spool in the trimmer, you need to gently hold the spring parallel while inserting the line into the slots of the brush head. And in the end, it just needs to be secured with the final part, that is, with a lid.

After threading the trimmer, you need to check it. If you did everything correctly, everything will work, but if you make a mistake, we recommend that you read the article again, or even better, if you watch the video on how to install a line on a reel in a trimmer.

How to remove the line from the trimmer spool

Over time, the cutting element of the head wears out, and it becomes necessary to pull out the remnants of the old line. Not everyone knows how to do this. Our step-by-step instructions plus a video on how to pull the thread from the trimmer spool, which you can find on the net, will help in solving this issue.

New! How to Re-Spool the Dewalt DCST920 20V Max Cordless String Weed Trimmer!

It is necessary to disassemble the mowing head

Remove the cover using the clips

We clean the remnants of cutting material

Hard ? Of course not. But if, nevertheless, doubts creep into you that for some reason you cannot do this, then, of course, find and watch the video how to pull out or how to wind the thread on the reel of a brushcutter.

How to wind the line onto the trimmer spool

05 July 2018

The trimmer is a great solution for those who have a large garden or lawn near the house that needs to be constantly trimmed. But like any other tool, sometimes it requires intervention. After some time, it will become necessary to replace certain elements, and this will have to be learned.

How can this be done? To replace the main cutting element, you must first select it correctly. In principle, the instruction manual for brushcutters should indicate the diameter of the thread to be used in it.

When you have acquired the required cutting element, try to install it correctly. It should be noted that there are a huge number of videos on the Internet that will help you figure out how to properly thread the line into the trimmer coil.

How to replace the line on an electric trimmer

In fact, it makes no difference which oblique you use, be it electric or gasoline. Threading is the same. The only difference is that if you use a gas streamer, you get more freedom, since you are not limited by the cable that is present on the electric streamer.

Yes, do not hesitate to use the special videos on installing or threading the line in an electric scooter, which can teach you much faster than simple reading.

How to wind the line onto the trimmer spool

The line in the trimmer head can run out at the most inopportune moment when the work is in full swing. So that the replacement of the fishing line does not take much time and does not have to go through the instructions for a long time, we recommend that you theoretically familiarize yourself with this process in advance. From our article you will learn all the subtleties, starting with the choice of consumables and ending with winding on spools of different types.

• What do you need?
• Line replacement process
• Video
• Useful articles

What do you need?

Line replacement process

Line selection

For each trimmer, the manufacturer recommends a fishing line or cord of a certain diameter. a reel is made for it. It can be from 1.2 to 4 mm: you need to look at the instructions for what line sizes are acceptable for your tool. For example, many trimmers have a maximum value of 3 mm (recommended for tough grass). a thicker cord cannot be fitted. For cutting young, soft vegetation, a thin line with a diameter of 1.2. 1.6 mm is suitable. Also, when choosing, pay attention to the structure of the cord: round is the most durable and suitable for coarse grass, curly. for soft, twisted or notched. for thin stems. Depending on what kind of grass grows on the site. lawn or weed, buy the appropriate consumable. The length of the winding can be from several tens to several hundred meters, and its price depends on this. You need to proceed from the amount of work to be done. If the trimmer is used in a private household, there is no need to buy a roll over 100 m.

It is important to know! Buy only branded line recommended by the trimmer manufacturer. It is made of high-quality materials and is durable. it will cut the grass perfectly and not wear out so quickly.

For one threading of the line into the bobbin, a length of 2 to 4 m is required. it all depends on its thickness and the manufacturer’s recommendations. If you wind more, the movement of the line will be difficult, and in the process of work, you may have problems pulling out new ends. Unwind the required amount and cut with a knife.

Helpful Hint: Place a piece of cord in water for 30 minutes, then it will become more elastic and stronger.

Removing the spool from the spit

Replacing a Weed Eater String (String Trimmer Line) | The Home Depot

To insert the line into the trimmer head, you must remove it from the tool. Depending on the design, this can be done by pressing the latches or unwinding the lamb. Pay attention to the direction of the thread. right or left. and rotate the wing depending on this. Usually the direction of rotation is indicated by an arrow on the trimmer head housing. It is recommended to carry out this operation with gloves. fingers will not slip, and hands will not get dirty.

Dismantling the mowing head

The line is wound on a spool, which is hidden in the trimmer head housing. To get to it, you need to disassemble the element. On the case there are latches-latches, when you press them, the case cover can be easily removed. Sometimes disassembly is carried out by untwisting the case.

Be careful! Remember in what order the elements are installed, how the spring and the fixing screw are located inside the head. Stack all the parts neatly in one place so that nothing gets lost and there are no problems during assembly.

Line winding

Trimmer heads differ in structure, reel type and line pulling principle. Having disassembled the case, you will see the spool and determine what type it belongs to. There are products with a middle edge that divides the reel into a top and bottom for each end of the line. In products without it, the line winding is solid. To make the process clearer, we suggest using the table.

Winding line on reels of different types

With dividing edge

Without dividing board

We have described how to wind the line into the reel of a double-barbed trimmer. This is the most common option. But there are other ways as well. For example, if there is one antenna in the mowing head, then winding is carried out without folding the line. Rotate in the direction indicated on the bobbin body, and the free end of the cord is temporarily fixed in the slot on the body. For trimmers with four antennae, four short sections are consumable, which are inserted in turn into the holes of an already assembled head.

Helpful hint: when winding the line, be careful not to pull it tight, so that it does not sit very tightly in the reel. It is necessary to ensure its free movement for subsequent pulling.

After the line is wound on the spool, it is necessary to assemble the body. Position the spool so that the ends of the line can be pulled into the trimmer head outlets. The slots in the spool where they were temporarily inserted will prevent them from slipping out. If there are no such slots, support the ends with your fingers as you insert the coil into the body. After pulling the free ends into the outlet openings, close the lid and secure it with latches or twist. Place the mowing head on the trimmer and pull out the ends of the line to the required length so that they do not touch the protective cover during operation. Done! You can get to work!

Line selection

To easily wind the line around the trimmer reel, it is worth deciding what tasks the garden tool will perform. The thicker the thread that is threaded into the head, the more difficult the tasks it will be able to accomplish. It should be noted that a universal thread is often used, the width of which does not exceed 2 mm. You, in turn, can determine the size using the following methods:

• familiarize yourself with the information contained in the instructions from the manufacturer;
• check the suitability of the fishing line for use on your own by trying to insert it into the hole of the reel;
• examine the spool for information on the diameters acceptable for use.

The selection of line for threading into the trimmer reel can be carried out according to the type of engine. For example, an excessively thick thread can increase the rotational resistance. Because of this, the load on the engine will increase, which will certainly affect the quality and terms of its further operation.

Avoiding negative consequences is not difficult. To do this, it must be borne in mind that for electric motors with a power of up to 500 W, a fishing line with a diameter of up to 1.2 mm is ideal. If you cannot get such a thread, you can use a 1.6 mm cord. A thread with a diameter of 2 mm, in turn, is used for motors with a power of more than 1 kW. It should be noted that 2 mm cord is often used for winding on a bent mower. If the gasoline device has a straight shaft, use a 2.5 or 3 mm thread. The thickest lines are installed exclusively on devices with a power equal to or greater than 1.3 kW.

Last but not least, the cross section of the line is. When choosing it, you should focus on the tasks set for the garden tool. There are several popular section options:

• twisted. has a small margin of safety, which is why it is suitable exclusively for young grass;
• serrated. characterized by sharp edges, suitable for working in weedy areas;
• round is the most common section. Such lines do well with fresh grass, but are not suitable for shrubs and dead wood;
• rectangular, square and star section types. due to low strength they are used for work on lawns.

The strongest and most versatile cord is a two-piece round line with a core inside. It is this thread that is suitable for most work. It should be remembered that the use of fishing line, ordinary wire and other third-party materials as a cord is dangerous for others.

Removing and disassembling the coil

To properly rewind the line on the trimmer spool, you need to familiarize yourself with the structure of the trimmer head. It consists of a protective cover, a bobbin with thread, a housing cover, and a spring, which is present only in some devices.

Before disassembling the coil, it is necessary to completely turn off / de-energize the device. In this case, the way of carrying out the work directly depends on the type of head. The first option is to carry out the following actions:

• User presses down on the latches located on both sides of the cover.
• After removing the cover, the spool is removed. Some models may have a spring that must also be removed.
• There is a screw in the center of the case, which should be unscrewed with a regular screwdriver.
• When the fasteners are removed, it remains to remove the gearbox from the shaft, gently shaking the product body.

The second option for removing the spool for threading the line into the trimmer is to screw the head onto the gear shaft. To carry out such a procedure, many devices are equipped with a hole into which an instrument can be inserted. When the screwdriver is inserted, the user only needs to grasp the product body and rotate it clockwise. It is noteworthy that this method, in contrast to the previously described method, is simple to execute.

Spool Trimmer Heads

The head is the main part of the trimmer. It is a base with a spool on which a cord thread is wound. In total, there are 3 types of heads:

• Manual. Allows you to lengthen the cord (line) manually after a complete stop of the engine.
• Semi-automatic. The use of such a head is simple and convenient. It works according to the following principle: after waiting until the trimmer reaches maximum speed, the user gently knocks the head of the device on the ground, due to which the blocking of the line is removed. Thus, the cord is pushed out due to centrifugal force, and the owner of the device only needs to cut it off with a knife.
• Automatic. The line is fed after the engine speed has decreased. Such a head turns out to be convenient in cases where there is a need for long-term work. The disadvantage of the device, in turn, is the rapid wear of the cord thread.

Now, to figure out how to thread the trimmer spool, you should pay attention to the choice of cord.

How to wind the line onto the trimmer spool

Line winding

It’s easy to insert the line into the trimmer. To carry out this operation, you must adhere to a simple algorithm of actions. The first step will be to determine the sufficient amount of consumables. To make its calculations, it is necessary to wind the line on the spool so that the resulting skein is less than or equal to the diameter of the sides of the structure.

When you have decided on the size of the cord, you need to fold it in such a way that one part of it is 15 cm longer than the other. The winding of the cord thread begins with a bead dividing the bobbin into 2 parts. There will be a mount in which you need to insert the thread, bent in half.

Now you need to understand in which direction to thread the line into the trimmer. To do this, you need to inspect the spool. often a special arrow is indicated on it. If there is no explanatory information, find the pointer on the trimmer head and start winding in the opposite direction. Further actions can be divided into 4 stages:

• Completion of winding of the cord. To do this, it is inserted into the side groove on the reel. Its second end is attached to the opposite groove.
• The ends of the fixed line are trimmed. 7-10 cm allowances remain.
• The filled part is placed in the trimmer head. For this, alternate insertion and pulling of the thread into the inlet holes of the structure is performed.
• The thread is pulled out of the grooves. Upon completion of the action, the cover of the product is fixed using the clamps.

After completing the last step, the garden tool is ready to go. If the device does not work correctly after inserting the line into the trimmer, it is recommended to repeat the procedure by changing the thickness or type of cord. Otherwise, the product may be damaged.

Coil with one working tendril

The simplest option and uncomplicated sequence of actions:

• The dimensions of the reel and the length of the original factory winding determine the recommended length of the line for winding. 2. 5 m.
• One end of the line is inserted into the fixing technological hole located inside the spool.
• The fishing line is wound on the drum in the opposite direction of the spool rotation on the trimmer product. as a rule, on the inside of the reel, an arrow indicates in which direction the winding is carried out.
• A small section of the line is left free to bring it out. it is fixed in a specialized groove on the inner side of the bobbin, designed to hold the winding when assembling the bobbin into working condition.
• The left end of the line is passed through the hole in the outer part of the reel.
• The bobbin halves are assembled and put on the trimmer bar.

Instructions with a step-by-step description of how to wind the trimmer coil and petrol cutters

In order not to be mistaken with the choice of a suitable fishing line for your tool, you should first disassemble the head and look at the side wall of the reel. This information is usually presented on a tip, which will not allow you to make mistakes with the use of the appropriate equipment.

If there is information on the reel about the diameter of the line you can fill in, then this information can be clarified in the instructions. Having decided on the thickness or diameter of the rig, it remains to figure out how to charge it. There are two ways to do this, but not all of them are applicable. We will consider both methods in detail, and depending on which models of brushcutters and trimmers you use, you decide on your own which option is suitable.

Method 1. how to properly wind the line or put it on a reel and choose the required length

To implement this method, you will need to first prepare a fishing line of the required length (usually up to 4 meters). It all depends on the thickness of the equipment used, as well as the design of the coil. There is an easy way to find out the amount of line you need to refuel to charge the reel. To do this, wind the rig inside the coil until it is aligned with the side protrusions. In this case, the rigging should not go beyond these extreme protrusions.

The thicker the equipment used, the shorter its length will be needed and vice versa, the thinner, the longer the segment will be needed.

The instruction on how to properly tuck the equipment into the trimmer or brushcutter is as follows:

• To begin with, a piece of fishing line that was prepared to be installed in a reel must be folded in half. In this case, one edge should protrude more than the second by 10-15 cm
• After that, take the second end from the other side, and fold it in half. Move to it so that the measured protrusion of 15 cm is preserved
• There is a slot in the inner baffle of the coil, into which the resulting loop should be inserted. The cut in the wall is shown in the photo below.
• Next, we find out the direction of winding the line. If you wind the rig in the wrong direction, then it will not function correctly, and you will need to redo the work. To insert the line and wind it in the correct direction, inspect the surface of the spool. The direction of winding should be indicated on it (in 99% of cases, this direction is indicated). What the direction indicator on the coil looks like is shown in the photo below.
• This arrow-shaped pointer can also have the designation, as in the example above “WIND LINE”, which means the direction of winding. If the pointer is missing on the reel, then you need to look at the head. There is a direction of its rotation on the head, and in order to properly wind the line, wind it on the drum in the opposite direction to the indication of the arrow indicator. So, if the arrow is on the tip, then you need to wind in the indicated direction, and if it is not there, then you should wind against the direction of the arrow on the surface of the head
• Having decided on the direction of rotation, you should start winding. Each end should be guided in its own groove. If there is no separator, then the equipment must be laid in the appropriate distribution order.
• When almost all the fishing line is wound on a reel, you will need to do the following. place a short part in the hole of the side wall of the pickup, the protrusion of which should be up to 10-15 cm, and then do the same procedure with the other end, placing it in the hole on the parallel side
• We insert the coil into the head, first passing the ends of the fishing line into the holes of the drum
• We put the drum in place and, by pulling the ends of the line, we disengage them from the temporary clamps in the wall of the reel. After that, you can put on the cover until the latch engages.
• This completes the process of how to replace the fishing line on the trimmer, and if necessary, you can only trim the ends (if their length does not suit), and install the assembled drum on the tool

With how to put the drum in place, no difficulties arise. There is a second way, how to charge the mowing equipment in the brushcutter. What is the difference, and how is the second method of threading the line on the reel of the brushcutter carried out, we will find out in detail.

How does the head with a fishing line work on a brushcutter why you need to know the principle of operation

Depending on the manufacturer, the heads differ structurally not only externally, but also internally. Most drums have a pressure spring inside (semi-automatic and automatic). Above is an instruction on how to disassemble the trimmer head without a spring, i.e. on the head of the manual type. The principle of dismantling a semi-automatic head with a spring inside is almost identical to the instructions described above.

The principle of operation of the semi-automatic trimmer coil is as follows:

• Inside the head there is a coil, which is fitted on the slots, which prevent its free movement.
• A spring acts on the coil, which presses it against the splines in the cover structure
• A fishing line is wound on the tip, the length of which depends on the tool itself. Typically this length is between 1 and 4 meters.
• During the performance of work, if it is necessary to increase the length of the line, the protruding part of the drum is pressed, whereby it disengages from the splines. In this case, the line is unwound from the drum, increasing in length
• After releasing the required amount of fishing line, release the pressure and continue cutting the grass

The advantage of a tool with a line is that this consumable does not require sharpening, compared to metal discs. In addition, if a stone or a tree comes across on the way, the line simply breaks off, without negatively affecting the gearbox and engine of the tool, as is the case with metal cutting discs.

Knowing the design and device of the types of mowing or trimmer heads, it is necessary to go on to consider the process of threading the line into the trimmer spool. After all, it is this very moment that causes difficulties for most owners of special tools.

What you need to know about trimmer line

A fishing line is a consumable that is made of nylon and serves as a cutting device. By means of this equipment, the grass is cut, which is ensured by rotating the tool head at a high frequency. This material has a different thickness, which depends on its use on the corresponding tools, electric low-power (from 1 to 1.6 mm), electric from 500 W (2-2.4 mm) and gasoline trimmers with brushcutters (from 2.4 to 3. 2 mm).

The more powerful the tool, the correspondingly thicker the cutting equipment should be. This affects not only the quality of the grass cut, but also the service life of the material. If you are wondering how to wind the trimmer coil, then it is time to change and recharge the tool. With the onset of spring, this question is becoming more and more popular, so it’s time to figure out the step-by-step instructions for replacing the line in the trimmer reel.

Method 2. how to properly put the line on the reel of the brushcutter with photo description and video

The second method differs from the first in that it is not a single piece of equipment that is charged into the coil, but segments from two parts. This method is used by manufacturers, and it is also suitable for those who have leftover material. The principle of how to insert two lengths of line into the brushcutter is the same as with the first method, and to make sure of this, below are detailed instructions:

• There are two equal length pieces of material that you can use.
• One piece is taken, and the edge is bent in the form of a clamping bracket or hook, with which the fishing line will be fixed
• Inside the coil there are holes in the form of a bracket for fixing, which are there for a reason. If they are not there, then the second option will not work. The appearance of these brackets is shown in the photo below. Each bracket is in its own half
• The brace of the fishing line should be hooked on the bracket, and wind it in observing the direction of the arrow
• The rig is wound until a 10-15 cm segment remains, which is fixed in the corresponding hole on the side of the guide
• Manipulations with the second end of the fishing line are carried out in the same way.
• The protrusions are inserted into the holes of the head, and then, removing the equipment from the temporary fasteners in the reel, a cover with latches is installed

The above instructions on how to install a fishing line in a brushcutter will help not only correctly, but also quickly make the replacement procedure. Assembling the trimmer coil, as mentioned above, can be done without removing the head, but in this case, you will need to conveniently fix the tool. Video instruction is presented below.

How to remove the spool from the trimmer and remove the line

Initially, remove the line from the trimmer spool before inserting it into the trimmer spool. A reel or aiming device is a device that sits inside the mowing head, bobbin or drum. There are different types of heads (depending on the manufacturer), but the principle of replacing the line on the reel is the same for everyone. First of all, we will figure out how to remove the head from the tool, as well as how to get the drum and fishing line out of it.

The instruction on how to unscrew the manual head on the trimmer is as follows:

• Turn the tool upside down and, if necessary, clean it from dirt. With two fingers of one hand, grip the cover latches (on the mowing head), which are symmetrically positioned to each other. After lightly pressing them inward, remove the protective cover from the drum
• Next, remove the line spool from the drum shaft. It is mounted on a shaft without fasteners, therefore it can be dismantled with one hand
• The main part of the drum is fixed with a screw, which must be unscrewed with a screwdriver with an appropriate tip or bit
• To unscrew, hold the drum base with one hand, and unscrew it counterclockwise with a screwdriver with the other.
• After that, you can start dismantling. To do this, you do not need to pull it with all your strength, but slightly shaking it to the sides, slowly disengage it from the metal shaft on which the drum is seated.
• When reinstalling, fit the head into the square slots

Echo SRM 225 – Replacing the Trimmer Line

This process is not difficult, and as you understand, there is no need to dismantle the entire head if you know how the replacement is performed. When dismantling, consider the following nuances:

• Periodic removal of the head is recommended to prevent corrosion of the threaded connection. If you never unscrew the screw, then if necessary, it will be difficult and even impossible to do this.
• If the screw has a four-sided bore of the head, then for unscrewing it is necessary to select a screwdriver or bits of a suitable size in order to exclude the licking of the edges on the head
• When assembling the unit, treat the threaded seat with lubricants, for example, grease or machine oil.
• If the edges on the screw are licked, then special clamping pliers can be used to unscrew it.
• There are drums that do not require preliminary disassembly. To dismantle them, grab it and rotate in the opposite direction to the clockwise direction

Knowing how to disassemble the drum, you should continue to figure out how to replace the trimmer line. The video below shows a detailed process on how to open the trimmer coil and disassemble it.

than 200 types of trimmers in one place at the lowest prices. Click and watch

Now, having removed and disassembled the coil, we proceed, in fact, to winding.

Now only I bite!

I caught this pike with a bite activator. No more fishing without a catch and looking for excuses for your bad luck! It’s time to change everything. The best bite activator of the year! Made in Italy.

Trimmer head with two antennae

Head with two flutes

After removing the spool from the spool body, we determine the number of strands for winding the fishing line (1 or 2). There is no fundamental difference between bobbins with one and two grooves, but if carelessly threading into the twin groove, there will be operational problems. Due to the likelihood of interlacing adjacent lines of the tool, a situation may arise when, after wear of the working antennae, it is impossible to remove new ones.

Regardless of the number of streams, a fishing line with a length of 1.5 to 3 meters is taken for refueling. Winding must be done in the opposite direction to the rotation of the head, since winding in the direction of travel will lead to the fact that the line will not be removed from the reel. After the fishing line is tucked into the trimmer coil, thread the free ends (15-30 cm) into special holes. Next, we assemble the head in the reverse order of disassembly and check the operability. Do not worry if the ends of the two antennae are very different in size, because when you start the trimmer, the knife installed on the protection will cut off the excess.

How to wind the line around the trimmer cutter head or brushcutters

The video shows in detail how to wind the line on a trimmer reel or brushcutter. Refueling with mowing line.

Features of the use of trimmers

A trimmer that mows grass with a fishing line can be used near: houses and other buildings, fences and hedges, trees and shrubs, beds and flower beds, row spacing in a garden plot.

Such a convenient, and most importantly, effective device like a trimmer exists in several variations:

• petrol;
• rechargeable;
• electric.

As the names suggest, trimmer types differ markedly from one another. But regardless of the type of this tool, a fishing line can be its cutting element. Of course, the line tucked into the trimmer reel is not endless. And sooner or later you will need to replace it with a new one.

Line consumption directly depends on the frequency of use of the device and the scale of the work performed. The more grass is cut and the more often it is trimmed with the trimmer, the more active the line is used in it. And, accordingly, the faster it will end. In this regard, the question arises: how to thread the line into the trimmer spool?

Not everyone knows the answer to this question. But the winding of the line on the reel plays an important role in the trimmer operation. For the device to function properly, it is very important to properly wind the new line onto the reel. How to change the line on the trimmer, and will be discussed in this article.

Trimmer head with automatic line threading

Trimmer head types

Some models on the market have a reel with an automatic winding mechanism. It is enough for the owner to properly thread and fix the ends in the head, and the winding operation will be performed by the tool itself when it is turned on. It is almost impossible to wind the line incorrectly in a trimmer with such a head, since the coil independently determines the position of the antennae. The advantages of an automatic trimmer head include ease of threading the line, and the disadvantages are frequent breakdowns of the mechanism due to the complexity of the design and high cost.

What you need to know about trimmer line

A fishing line is a consumable that is made of nylon and serves as a cutting device. By means of this equipment, the grass is cut, which is ensured by rotating the tool head at a high frequency. This material has a different thickness, which depends on its use on the corresponding tools, electric low-power (from 1 to 1.6 mm), electric from 500 W (2-2.4 mm) and gasoline trimmers with brushcutters (from 2.4 to 3. 2 mm).

The more powerful the tool, the correspondingly thicker the cutting equipment should be. This affects not only the quality of the grass cut, but also the service life of the material. If you are wondering how to wind the trimmer coil, then it is time to change and recharge the tool. With the onset of spring, this question is becoming more and more popular, so it’s time to figure out the step-by-step instructions for replacing the line in the trimmer reel.