How To Remove The Coil From The Electric Trimmer

The first way

Line bent in half

The prepared segment (in this case, it is 4 meters) is bent approximately in half. one segment should be 15-20 cm longer, and inserted into a special slot located on the dividing wall.

The line is inserted into the slot

In a certain direction earlier, the fishing line is wound. This is done in an interference fit, the line is neatly distributed. In this case, you need to wind a segment that is longer in the section that is closer to the button.

There are designs that do not provide for dividing the coil into two sections. This does NOT change anything, the line is wound in a similar way. You just need to make sure that the segments do not overlap with each other.

The first should end that segment, which is located at the bottom of the coil, i.E. The one closest to the fixing holes.

This tip fits into the corresponding hole in diameter. The line is securely fixed.

The line is securely fixed

A long segment is wound another half turn. There he is similarly fixed. In this case, the segment crosses another section of the coil.

A long segment is wound another half turn

The fixed ends of the coiled line are inserted into the holes of the trimmer spool body.

The fixed ends of the coiled line are inserted into the holes of the trimmer spool body

The coil is attached to the body. The ends of the fishing line are pulled with effort so that the fishing line, fixed earlier in the holes of the reel, pops out from there. It is easily identified by the characteristic sound (click).

The ends of the line pull up with effort

Button spool snaps into trimmer spool housing.

Button spool snaps into trimmer spool housing

The line was changed successfully. In this case, you need to set it back to the trimmer and you can start Mowing the grass.

It should be repeated, it is not necessary to remove the spool from the trimmer. this was done for clarity of the process of replacing the fishing line. You can disassemble the spool in place, wind it on the spool and put it back.

Line replacement completed successfully

The tip so that they do not hit the trimmer cover can and should be trimmed.

How to wind the line around the trimmer cutter head or lawn mowers. Coil with one working tendril

The simplest option and uncomplicated sequence of actions:

• The dimensions of the reel and the length of the original factory winding determine the recommended length of the line for winding. 2. 5 m.
• One end of the line is inserted into the fixing technological hole located inside the spool.
• The fishing line is wound on the drum in the reverse rotation of the spool in the direction of the trimmer. as a rule, on the inside of the bobbin an arrow indicates in which direction the winding is being carried out.
• A small section of the fishing line is left free to lead it out. it is fixed in a specialized groove on the inside of the bobbin, designed to hold the winding when assembling the bobbin into working condition.
• The left end of the line is passed through the hole in the outer part of the reel.
• The bobbin halves are assembled and put on the trimmer bar.

How To Change The Coil To Trimmers

How to wind line around the trimmer cutter head or lawn mowers

Changing the line in the trimmer: 2 easy ways

Feedback from our readers is very important for us. Leave your rating in the comments with the reasoning for your choice. Your opinion will be useful to other users.

Method 2. two segments

Two coiled line pieces

Fundamentally does not differ from the method The only difference is two wound pieces of fishing line, instead of one.

The end of each segment is folded

The end of each segment is folded.

Two special fixing sockets

There are two special fixing sockets on the coil (see picture above).

We start reeling the line

They hook it with a hook formed earlier on the fishing line, and begin to wind the fishing line.

Winding is carried out in a special order

The winding must be carried out in the following order: first the lower line, i.E. The one that is closer to the fixing holes at the bottom of the coil, and only then the top one, i.E. The one that will overlap the bottom section.

The bottom line is reeling

The tip is made into the holes in the trimmer spool body. They are pulled to clicks, which means that the line has come out of the clips.

The tip is threaded into the holes in the trimmer spool body

The coil is fastened into the body. The line in the spool has been replaced.

The line in the spool has been replaced

Trimmer head with two tendrils

Double flute head

After removing the spool from the spool body, we determine the number of strands for winding the line (1 or 2). In principle, there is no difference between bobbins with one and two grooves, but with careless threading into the paired groove, there will be operational problems. Due to the likelihood of interlacing the adjacent line of the tool, a situation may arise when, after wear of the working antennae, it is impossible to remove new ones.

Regardless of the number of streams, a fishing line with a length of 1.5 to 3 meters is taken for refueling. Winding must be done in the opposite direction of rotation of the head, since winding in the direction of travel will lead to the fact that the line will not be removed from the reel. After the fishing line is tucked into the trimmer coil, the free ends (15-30 cm) are threaded into special holes. Next, we assemble the head in the reverse order of disassembly and check the operability. Do NOT worry if the ends of the two antennae are very different in size, because when you start the trimmer, the knife installed on the protection will cut off excess.

How to remove and put a reel on a lawn mower!

Subscribe to the channel! And we will teach you everything)))

Step 3. disassemble the coil

After the coil is removed from the head, it must be carefully disassembled. It is better to do this on an already mown area, because there may be a spring inside the coil, which will be quite difficult to find in the highest grass. Electric trimmer wiring diagram with half electric trimmer As you have seen. After disassembly, we will have three parts on our hands: the body (top cover), the protective casing and the coil itself.

Coil with two working tendrils

In this type of spools, you should determine the number of grooves for winding the line, lying on the inside of the spool:

• One groove. both tendrils are wound together in one groove;
• Two grooves. each antenna is wound on an individual groove.

For both cases, a line with a length of 2-3 m is taken.In single-groove reels, the line is pulled into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the rod side. inside the arrow usually indicates the correct direction of winding. If there are fixing grooves, the ends of the fishing line are threaded through them or held with the fingers of the free hand, they are threaded into the through hole of the outer half of the bobbin, the bobbin is closed and attached to the trimmer bar.

The difference in line winding in two-groove spools is that initially a 2-5 m long line segment is folded in half (to determine the mid-bend), and the bend loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each along its own groove, fixing the antennae and assembling the coil is similar to the above-described option with one groove.

The first execution of this procedure, perhaps, will seem long and rather laborious, but with time and experience this task will be solved much faster and easier.

The following will clearly show how to thread the line into the trimmer spool and wind it correctly. this operation is NOT difficult and with some patience it will certainly be crowned with success:

Threading the spools with thread of different types of bobbins

It should be noted that there are several types of fishing tackle reels:

• Inertial;
• Inertia-free;
• Multiplier.

For each type of non-inertia reel, its own diameter is intended. Fishing whine. If the thread is thicker, it will NOT be possible to thread it into the spool. Difficulties will also arise if, for example, a too thin monofilament is used, and not one or another spool intended for refueling.

In the case of threading a non-inertia spool, one of two well-known methods is used:. “cross-to-cross”. parallel winding, that is, thread after thread lies parallel to each other.

Now in the multiplier bobbins. Multiplier spools are subspecies of inertial ones. Many fishermen make the same mistake, they tie the end of the string to the farthest hole of this element. It is wrong to do this, it is worth tying only for closely located holes.

Filling the Fishing reel with a bobbin thread is done as follows:

• First monofilament is fixed to the spool body.
• Next, you need to attach the coil to the spinning rod and pass the free end of the scaffold through the right ring.
• Tighten the device that protects the tackle from jerking fish.
• Tighten axle brake.
• Now you can wind up by guiding the line and, thus, controlling it.

Winding the line onto the trimmer reel. instructions

Using this or that tool or device, sooner or later you have to change some of its components, refuel, and so on.

For example, refueling the fishing tackle trimmer coil is quite simple, but there are some nuances that cannot be ignored. Here we need precise answers to the questions: how much and how?

Instructions on how to wind the line on the trimmer spool

Here are the steps for winding a monofilament fishing whine on a trimmer spool:

• The end of the line from the reel is pulled into the pass rings of the finished tackle.
• Open the line guide.
• Using any fishing knot, tie one end of the monofilament to the bobbin.
• Make a few turns by hand, move the spool wheel.
• Now winding can be done with the handle.
• When the winding is done, you need to close the line guide.

In another method, bobbins with fishing line should be thrown over some kind of stick so that the bobbin rotates freely around its axis. The next step is to wind the trimmer bobbin. Here it will not be very convenient to wind a friend, it is better to resort to the help of a friend.

As for winding the braid, the following steps must be taken:

• Dip the prepared bobbins with braid into a container of warm water, or at least into the water of a river or lake, right on the spot.
• Now you need to wind up. Due to the more or less softened fiber, the line will lie down and wind up quite evenly and tightly.

How to remove the spool from the trimmer?

So that the assembly process is not long and tedious, it is best to put the elements of the untwisted mechanism in order. It won’t let you get confused.

Here are the steps for parsing:

• The clutch nut is unscrewed.
• Next, you need to untwist all the small washers and gears.
• Need to remove the handle.
• Need to disassemble the spool mechanism.
• The rotor is removed
• Now the line guide roller is disassembled.
• Next, the coil is removed.

What line is used for the trimmer?

One of the types of fishing line is used to refuel the reel:. monofilament. It is a versatile single-thread fishing thread. The composition includes plastic compounds, polyethylene and everything like that.

Whole factories are engaged in the manufacture of monofilament, which try to make the fishing line as efficient as possible each time, “able” to create the most approximate game of bait to live. Wicker. Two types of braids can be distinguished here: classic and braided cord in a sheath.

Tips from experienced fishermen

Here’s what professional fishermen advise:

• DO NOT wind too much line. This suggests that if the permissible winding length is 100 meters, then in this case you need to wind a little less. This will allow the device to work more correctly.
• When winding, the string should NOT be too tight or, conversely, loose. And in that, in another case, it will NOT fit as it should. It can twist, go to the side, overlap, and so on. Conical layers of fishing line can also form, that is, thickenings on one side or another.
• The winding should be carried out not reaching the upper edge of the coil, about 1-2 mm, this distance may increase slightly.
• If the line is dropped periodically during winding, then you need to take a little more than the previous distance from the side wall of the spool to the line being wound. You need to increase literally by 0.5 mm.
• Quickly winding the line will NOT distribute it well over the spool surface. On the contrary, it may “twist” so that it will be difficult to fix it. The best option is average speed.

There are also devices that allow you to attach the spools directly to the rod. This allows you to wind the line, firstly, without assistance, and secondly, the refueling process is greatly simplified.

How to wind the line into the trimmer?

When refueling the line for the first time, this process may seem quite laborious, but with time and dexterity, the task is solved much faster.

In order to fill the line, you must:

• Take the coil, Unscrew its cover. Some spools are threaded to the left, so the cover must be unscrewed in the required direction.
• Measure five meters of line;
• Fold this segment in half, that is, determine where the middle is;
• Next, place this middle of the line in a special hole on the reel;
• Wind the line in the direction of the arrow;
• If there are two places for winding, then the first part of the line should be wound on one half of the reel, and the second part on the other half;
• Both ends of the line are pushed into the reel holes;
• Screw the lid.

How to remove the spool from the trimmer?

To change or wind the cutting thread on the spool, it must be removed.

The complexity of its removal depends on the tool model:

• Low motor tool. The motor is almost in the ground here. To remove the coil you need to press the buttons located on the side of the trimmer. After pressing THESE buttons, the body opens, where the line spool is located.
• Curved bar trimmer. Here it is necessary to return a special lamb counterclockwise. Then the coil and the spring in it are removed.
• Straight bar tool. The bar is held still with a screwdriver or a second object. It is removed by turning it clockwise. After that, the tool is disassembled into parts and the bobbins are removed.

Line threading:

• If a tool with one tendril is used, then about four meters of thread will be needed. This thread is passed into a hole inside the spool where it can be fixed. Further, one end of the line is directed in the direction of the arrow. Then the end of this thread is fixed in the groove, which is in the bobbin. This is necessary so that the thread could not unwind when assembling the spool. If there are no grooves, hold the line with your hand and collect the bobbins.
• If a tool with two tendrils is used, then first check the number of grooves available.

If the reel is equipped with a semi-automatic mechanism, then the line is wound as follows:

• The thread is threaded through the hole that is inside;
• Secure the ends of the thread in the grooves on the body.
• The coil is assembled and a special button is pressed;
• After which the line itself begins to dangle in the right direction.

It must always be remembered that the cutting thread must be protected from hard things. This will extend its lifespan.

If you do not adhere to this rule, you will often have to stop work, remove the spool and change the thread to a new one.

Correct winding of the line to the trimmer spool. What line is used for the trimmer?

There are several types of fishing line:

• The most durable is rounded;
• For Mowing soft vegetation. curly;
• For mowing thin grass. from a notch;
• Special. suitable for certain types of trimmer.

The section of the cutting thread must correspond to the vegetation to be cut.

If it is necessary to replace the fishing line, then it is necessary to select exactly the type recommended by the manufacturer of this particular trimmer model, that is, the thickness of the cutting thread should be suitable for the engine power and the size of the unit.

It is better to choose a specialized cutting thread. It is worth soaking the line for a while if you plan to replace it in the reel.

After soaking, it gains elasticity and becomes stronger.

The cutting thread can be made from different components. The most common among them is nylon.

This material is characterized by a high degree of wear resistance, the ability to withstand various temperatures and high loads.

Nylon line can be stored for a long time, It will not dry out or lose its strength.

Therefore, its service life can be quite long.

Lawn mower spools or heads have different structure:

• One-string. There is only one working line in the modification of such a trimmer. This unit is used mainly for small jobs, such as trimming grass.
• Two-stringed. They can be both automatic and semi-automatic. The package here includes two strings. This trimmer is used for mowing and clearing areas.

Instructions for correctly winding the cutting thread onto the trimmer spool:

• First of all, you need to disassemble the head. To do this, press the latch and return the cover to the side. Next, the spool is removed.
• Measure out the required amount of cutting thread and insert it into the slot.
• Wind the line on both sides in the direction of the arrow.
• Leave 15 cm ends NOT coiled.
• These ends are inserted into opposite slots.
• Then the ends are fixed in the hole on the head.
• After that, the spool is carefully inserted into the body, for this you need to slightly press on it.
• If necessary, you can pull the remaining ends of the thread outward. To do this, you first need to pull one end of the thread, and then the other so that they can easily pass through the slot on the head.
• Now you should collect the grooves on the body and screw the cover.
• Then press the spool and try to twist it all the way. If you hear a click, the spool has clicked.
• Next, you need to pull the free ends of the thread to the end.

Threading the spools with thread of different types of bobbins

With two-string automatic heads:

• First you need to press the clip to the click, remove the cover.
• Carefully return the bobbins so that it can detach from the holder. Extract her.
• Measure two lengths of cutting thread of the same length. To make further work easier, the ends of the line must be cut off at an angle. Take one end and push it into a special hole in the coil. It can also be slots, grooves, clamps, etc.
• Further in the direction of the arrow, you need to wind the fishing line, and quite tightly and evenly. In a special eyelet on the reel, you need to fix the end of the line.
• Subject the other half of the line to the same operation, only on the other half of the reel.
• The next step is to install the coil in the trimmer head. And thread the rest of the line through the hole in the head.
• Then carefully straighten the thread and close the lid. If the line turns out to be long, then it is better to cut off the excess. About fifteen centimeters should remain on each side.

On the semi-automatic head:

• The thread is threaded through the hole that is inside;
• Secure the ends of the thread in the grooves on the body.
• The coil is assembled and a special button is pressed;
• After which the line itself begins to dangle in the right direction.

It is necessary to very carefully and carefully thread the cutting thread into the unit, because not only the cleanliness of the garden area, but also personal safety depends on the correct winding of it.