How to remove the huter get 600 trimmer head

What types of woods are there

The most common type of line that fits almost all reel types is round cord. This is an ordinary fishing line, suitable for mowing succulent grass, but it will be much more difficult to mow dead wood with it, and even more so it will not cope with bush.

As a rule, the diameter that can be used to cut young grass does not exceed 1.6 mm. The thicker the thread, the more coarse grass it is able to overcome.

There are fishing lines with sharp edges in the form of an asterisk or a square, this option is more adapted to mowing dry grass just due to the existing sharp edges, but its disadvantage is greater wear and is inferior in strength to a round cord.

There are fishing lines with improved aerodynamics with characteristic dents, scales and notches, such a product makes less noise, but it is used only on lawn mowers, since the exit of such a thread from the spool is difficult, it is used most often with discs into which segments are inserted. The disadvantage of such a product is its fragility..

Most often in gasoline trimmers with an engine with an output of more than 1.5 hp. use cords with a metal cable inside.

This thread is ideal for cutting dry grass and small bushes. The presence of a core has a positive effect on the wear resistance of this material.

The disadvantage of such a cord is its price, which is significantly higher than the above opponents..

How to change the line in the trimmer and which one is better to choose

Since we examined the choice of a trimmer in the previous article, today we will tell you how to properly fill the trimmer with fishing line, and which one is better to choose based on the working conditions.

After you bought a trimmer and began to actively use it, sooner or later the question of replacing the fishing line will arise, since this is the most wearing element in the tool, intensive use of the trimmer will lead to frequent replacement of consumables.

How to remove or tuck the line into the trimmer

In order to wind the line, it will take about 10-15 minutes. What is a trimmer coil? Plastic body with a cassette inside, on which there is a special hook for easy winding of the fishing line.

remove, huter, trimmer, head

Almost all trimmer reels have a similar fastening principle, this is a central screw-button, when pressed, it becomes possible to pull out the line of the required length. The photo below shows a few examples of different trimmer spools..

The bobbins of the trimmers, the motor of which is located at the very ground, have a different attachment to the axis of rotation, they have two buttons on the spool located on the sides that need to be wrung out, otherwise the replacement of the thread is no different from other cassettes.

The principle of correct winding of the fishing line is similar in all of the above cases, therefore, for example, consider the standard version with two antennae.

Removing Craftsman (Model:CMXGTAMD25SC) Trimmer Head

To remove the spool with the fishing line, you need to unscrew the centrally located screw, but note that the thread is left there, so you will have to turn it clockwise, this was done on purpose so that during operation it does not open under the influence of centrifugal force.

Next, using a screwdriver, disassemble the head and remove the spool onto which the fishing line is directly wound.

Having measured the required length and folded in half, you need to tuck the fishing line into the spool, eventually bringing its ends opposite each other (for this there are special slots for fixing).

After that, it is necessary to assemble the head in the reverse order, threading the ends of the cord into two corresponding holes.

If you have doubts or it is not entirely clear how to load the line on the trimmer, we recommend that you look at how to properly wind the line into the lawn mower.

In this video, in detail, step by step, the instructor will open the trimmer head, measure the required amount of line, usually from two to four meters, and demonstrate assembly and installation on the trimmer.

Major coil malfunctions

Trimmer users and lawn mowers often face a problem with the semi-automatic mowing head. Coil malfunctions can be as follows:

  • the line does not lengthen automatically;
  • the cord spontaneously comes out of the reel.

DIY trimmer coil repair

The trimmer, whether petrol or electric, is the only solution for mowing grass in hard-to-reach places that a wheeled lawnmower cannot handle. As a cutting tool in trimmers, metal knives or special fishing line are used, which is tucked into the trimmer coil. But, unfortunately, trimmer heads become unusable over time during operation. Some malfunctions can be eliminated by hand, and some require a complete replacement of the mowing head..

The cord lengthens spontaneously

There are times when the trimmer user notices a very fast line flow. However, he never hit the ground with a button to lengthen the line. The reason for the fact that the line spontaneously lengthens, being cut on a special knife on the casing of the device, may be the absence of a spring in the mowing head. Often novice users of mowers, trying to load the line into the reel, forget to install the pressure spring in the head, or completely lose it when opening the lid, and in the future, do not even know about its existence.

Also, the line can be lengthened without using a button if the spring is loose. If checking the spring has confirmed this fact, then several washers must be placed under it in order to enhance its clamping properties..

How to remove the spool and replace the line

Trimmer owners, mostly beginners, find themselves in confusion, bordering on panic, when they need to change the cutting tool or line in the reel. Very often, when trying to unscrew the mowing head, users simply render it unusable, not suspecting that it is unscrewing in the opposite direction. To prevent this from happening, if you need to replace the tool, it is recommended that you read the step-by-step instructions below..

  • Stop the mowers engine or power off the trimmer before placing the line into the spool to avoid injury from accidental starting rotation of the cutting tool..
  • Unscrew the attachment attached to the gearbox shaft. To do this, the shaft must be fixed by aligning the holes on the washer and on the axle, and inserting a metal rod or screwdriver into them..
  • Unscrew the nozzle. You should be aware that the thread on the shaft is left-handed. Therefore, turn the trimmer coil to the right, that is, clockwise.
  • Disassemble the mowing head. Most often, the head cover is attached to the clips. To remove it, you will need to sink these latches into the case, squeezing the edges of the cover. If your trimmer has a semi-automatic mowing head with a button on the bottom, then the disassembly of the attachment should be done carefully, since you can lose the spring, which sometimes flies out when the cover is removed..
  • Cut off the required amount of line. Usually its length is 5 meters. Use a cord of the same diameter as indicated in the instructions for the tool. It is not recommended to exceed the maximum line diameter as this will result in increased engine load and higher gas mileage.
  • Find the midpoint of the line by folding it in half. You will have a loop.
  • Special grooves are cut inside the coil (there may be holes). Insert a loop of line into this groove..
  • Wind the line around the spool by turning it counterclockwise. It is necessary to fill in the cord as evenly as possible, the turns should lie down without overlap and with good tension. When the winding is finished, leave free ends of the line about 20 cm long and fix them in the grooves on the sides of the reel..
  • Assemble the mowing head. Be sure to insert the spring and washer (if equipped) before final assembly of the accessory. Place the spool in the body and thread the ends of the cord through the holes or lugs.
  • Put on the cover and secure it with the latches.
  • Screw the adapter back onto the gearbox shaft, also securing it with a screwdriver. You will need to twist the trimmer coil to the left (counter-clockwise).

Line does not lengthen automatically

If the line does not lengthen when you lightly hit the trimmer button on the ground, then the reasons for this may be the following.

Option 1 – a bite has occurred, i.e. clamping the cord between turns. This problem usually occurs if the user has been winding the line on the reel unevenly, with intersecting turns, or winding it with insufficient tension. In the latter case, when the mowing head rotates at high speeds under the influence of centrifugal force, the cord begins to tighten, as a result of which inter-turn clamping of the fishing line is possible. To fix the problem, you will have to disassemble the coil on the trimmer and rewind the cord correctly, that is, in even turns with good tension.

Option 2 – too short ends protrude from the head. The line may not come out when hitting the ground if the ends sticking out of the head are not long enough (short). In this case, the centrifugal force is not enough to stretch the line. Therefore, it is required to stop the unit (turn off the engine or disconnect the trimmer from the mains) and pull out the line manually, after pressing the button.

Option 3 – the line is brazed inside the mowing head. This causes the coil to lock and not spin when the button is pressed. Basically, this happens for several reasons: poor quality of the cord, overheating of the coil during prolonged operation of the unit, hitting the line against hard objects.

  • In the first case, third-party cord can be made of low-quality and low-melting materials that cannot withstand mechanical and thermal stress. Therefore, you should give preference to “branded” lines.
  • But, if you nevertheless purchased a fishing line of unknown quality, and it is often soldered during operation, then you can follow the example of some users who, after filling the cord into the reel, wet it with either silicone grease (from a can) or mineral oil. This procedure greatly reduces the likelihood of soldering the turns of the fishing line together.
  • Also, the line can be soldered if it hits a hard object (stone, fence, dry branch, etc.) during mowing. As a result, it stretches slightly and is pulled back into the head at high speed. From friction, the cord heats up, and its turns stick together. The only thing that can be done to eliminate this malfunction is to open the trimmer spool and rewind the line..

Trimmer coil device

Trimmer mowing heads come in a variety of designs, both simple and complex. The picture below shows an exploded view of the semi-automatic trimmer head from a Husqvarna (Husqvarna) lawn mower..

This type of head is present on most lawn mowers and trimmers such as Stihl (Stihl), Patriot (Patriot), Champion (Champion), Bosch (Bosch), Huter (Huter) and others. The device of the mowing head is quite simple. It includes the following details:

  • mowing head base;
  • button for semi-automatic cord feed;
  • bobbin (spool) into which the line is tucked;
  • spring;
  • eyes – through them the line comes out;
  • trimmer head cover;
  • line (cord).

There are also simpler trim heads shown in the following photo..

All these attachments do not allow you to change the length of the line in a semi-automatic mode (after pressing a button). If the cord breaks, you have to stop the mower and change it manually.

Is it possible to make a coil for a trimmer with your own hands

  • Take a piece of plywood or PCB and draw a circle about 14 cm in diameter on it.
  • Cut the disc with a jigsaw or metal hacksaw.
  • Drill a hole in the center of the disc that matches the diameter of the gearbox shaft. Do not forget to put a washer on it before installing the disc on the shaft..
  • Small corners can be screwed on the edges of the disc or 1-2 holes can be made on opposite sides. They will serve for refueling the fishing line in them..
  • Several screws can be screwed into the plywood to secure the line..

This homemade mowing head is secured to the shaft with a nut. It will not work to tighten or unscrew the nut without fixing the shaft. To replace the cord, it will be enough to loosen the screws, insert a piece of line of the required length and press it again.

Also, the mowing attachment for attaching the fishing line to it can be made of metal sheet. How to do this can be understood from the following video..

Quality comparison

Which Trimmers are Better than Huter or DDE

Andrey K. Advantages: only 1 tank has worked so far. running in passed. happy as an elephant. very easy to start!

Roman M. Advantages: Collapsible, power
Disadvantages: not found yet
Commentary: Prior to that, Texas used 1hp, Huter 3.4hp. (2500W) compared to it as a Ural motorcycle and a moped. I worked for about an hour (there was no more grass). I got a lot of pleasure and I hasten to share with you my first impressions. Thick line cuts big fat stems of burdocks and elderberries already spray flying! It seems that nothing can stop or suspend it! Before starting, balance the attachment point of the carabiner well. Before assembling the rod, wipe off the grease from the outside of the tube so that the retaining clip holds firmly and securely. Also wipe off the grease from the rubber plug that covers the open end of the disassembled rod. It is not necessary to overtighten so as not to disrupt the thread. Keeps assembled securely. Tighten the guard carefully, otherwise the nuts may cut into the plastic. As I understand it, it is made of polyethylene and is quite flexible. That’s all for now. There will be new impressions I will add! As promised, I will add. Worked out two tanks. A defect appeared on the third. When gas is added, the rpm drops. The service department said to adjust the bolt on the carburetor, spring-loaded, near the gasoline cabin. It was twisted half a turn. I also twisted 4 half-turns, achieving good performance with increasing throttle. Slightly adjusted the idle speed with the upper bolt. Works great again. He worked as a disk. A metal strip 2 cm wide and 3 mm thick accidentally fell into the grass. She cut it off while continuing to mow. Only a click was heard. He picked up a felled piece and…. “Surprised”. I did not find any special damage on the disk! In general, the power! This is the kind of braid I wanted to mow everything.

Shindaiwa trimmer head replacement

Dmitry D. Advantages: 600 W, but it mows – be healthy, not heavy, the plastic is strong, it is convenient to mow between the beds, it can be easily cleaned of grass, small size
Disadvantages: I can’t get used to changing the line quickly
Commentary: I bought it as a birthday present for my mother … As a result, I mow for her at the dacha myself, there are no problems with gasoline, smell, I even mowed small raspberries. I don’t mow after rain and try not to overheat the engine.

Arkady B. Advantages: easy to operate, light weight, fits in the trunk, low price, suitable for teenagers
Disadvantages: not found
Commentary: I do not mow it much near the house, in principle, I have enough of her power

Dmitry G. Advantages: Pretty nimble, for its power.
Disadvantages: Not quite a high-quality product. After 4 minutes, you need to give 6 minutes of rest (although I certainly work longer). Virtually non-removable mowing head (in the version with semi-automatic head).
Commentary: It is convenient for her to work, but all the same, if you mow for a long time, that is, there is tension on the back. The line in the kit is not the worst, but it is better to take a reinforced one, the consumption will be less, and the speed of work is higher. on over the fences, the pin was badly riveted, replaced with a bolt, let it be. Later, two of the four screws that fasten the casing tore off, screwed them a little larger, holds them normally. The cable is also of poor quality, punched closer to the casing, it was not immediately noticed, the trimmer worked, then it didn’t, and he heard a lot of unflattering epithets from me. After replacing the cable, I continued to mow. In the third season, when I met a thick, dry stem, the working part of the mowing head scattered, the part attached to the shaft remained intact. Well, I was not particularly worried, I thought I would pick up a new one … and then a problem arose, how to remove the lower part of the head at all, no bolts or holes for blocking the shaft were observed. Having rummaged in the internet, I found out that no one could take it off. The manufacturer, apparently, realized his mistake and in the new version of the trimmer completes the product with the simplest coil fastened with a bolt, unscrewed it, put another one and work. I turned to the service for advice, I thought the lower part was intact, take the upper part and that’s it, the coils, like nowhere else sale, and in the service for this model was not. The service worker talked about the principle of fastening – the coil simply shrinks, so pull … I pulled and the coil, along with the insides, breaking through the flimsy, thin ribs of the body, crawled out, well, thank God, the torment was over, to the landfill! One good trimmer took for 1690, now it is from 2400, I think it would have worked for more than one season if the manufacturer initially supplied it with a normally removable head! Now there are both options on sale, pay attention when buying. The new version in a different, more interesting design looks better, the head in which the fishing line will have to be pulled out by hand, but fastened with a bolt, in the old one is a semi-automatic head.

Andrey K. Advantages: Ease and simplicity of use. Starts with half a turn. Line and disc included.
Disadvantages: Not found yet.
Comment: I bought it for a summer cottage. I’m satisfied with the trimmer’s work. The collapsible bar is very convenient for transportation. For several years in operation, the Huter snow blower never let down, so the trimmer decided to take the same brand.

Nikolay Larionov Advantages: price, well assembled, seems to be economical
Disadvantages: not found yet
Commentary: I was looking for a simple but high quality trimmer. There was already a puncture, I bought a cheap one, but after the second mowing it burned out. The model came up in all respects, and the price was more than satisfied, I took it in the region of 6,000. Assembled well, everything is whole, properly screwed on. My grass is not high, and there were no problems at all. The fuel consumption is the same as indicated in the instructions, I thought it was underestimated, but no, it comes out very economically. The tank was enough for more than one time. I have already changed the fishing line once, also not difficult, in just a couple of steps. The trimmer justifies its price more than. Maybe when I use it more often, I can add something else, but for now I am completely satisfied with it..

Natalia Syutaeva Advantages: Budgetary cost. It does its job efficiently. Lightweight. Simplest management.
Disadvantages: Of the shortcomings for a year of using the trimmer, only an uncomfortable belt was identified.
Commentary: We bought a lawn mower at the end of spring last year. Its price is almost budgetary, and the quality is German. We didn’t regret it. The trimmer is really high quality. Copes with the most well-groomed areas of grass very easily. No need to process one patch of grass several times.

Alexey Advantages: Price.
Disadvantages: Heavy, high gas mileage.
Commentary: Before this trimmer, there was no experience of using. It is quite heavy, I mow only in unloading. On hands without a belt you will not drag this. I bought it cheaper than 5 thousand in May. In addition to the weight, there seem to be no complaints. The idle holds, the gearbox is cold, it starts up without problems. The price covers everything, for that kind of money it also works).

remove, huter, trimmer, head

Best T. Advantages: Inexpensive, reliable, comfortable, easy to start
Disadvantages: The quality of the plastic is poor, the gas tank cap does not always press tightly
Commentary: Hello everyone, I bought this trimmer last year. The whole season he worked for them in the country, the flight is normal, changed the head and several skeins of fishing line during the season. It is convenient to work, it is not heavy, not very noisy. In general, I am satisfied 🙂

Alexandr N. Pluses: Lightweight, starts up well, there is a disc included
Disadvantages: poor build quality, unreliable rod connection, cannot be mowed for a long time – it overheats.
Commentary: Mows well, starts up well, works steadily, vibration was due to improperly tucked line, and in general the line from the kit is bad, I put a normal line – I began to mow very well, the connection of the rod was cured by installing an aluminum tube. The gearbox was practically without lubrication, I put the grease can and syringed the “lithol” to work better. But with prolonged mowing, the piston rings crumbled – obvious overheating. I replaced the piston and rings in a month again the same result, you can mow no more than 1 hour a day. Suitable for mowing small areas, no more than a hundred square meters per day.

Mikhail D. Advantages: Compact when folded, easy to start.
Disadvantages: Loose connection, not very comfortable shoulder strap
Commentary: A good household tool, copes well with small volumes. Expecting something more for such little money is not worth it. A rich package bundle when buying will save your budget, there is no need to buy a lot of additional accessories. Everything is already included.

Stanislav Advantages: price / quality. Ease of operation. Light trimmer.
Disadvantages: After the driftwood remains less than half the tank, it periodically stalls if you tilt the trimmer clockwise.
Commentary: Long needed a gas trimmer to mow garden beds, house, bushes, trees and tiles. The electric one is annoying that the wire clings all the time. I am satisfied with the purchase. At first, I could not understand why it did not give out the line from the spool. Then I realized that the direction of winding the line on the bobbin was marked incorrectly (despite the fact that the line was wound incorrectly at the hehe factory). On the first day, the belt clip fell apart. It doesn’t matter, I’ll make a new one. As I already indicated in the shortcomings, the motor stalls when less than half of the tank remains if you turn the trimmer. This is how the fuel intake hose is located. Well, yes, this is a matter of habit. Half liter tank. Enough hours for 2 intensive work.

Lesya G. Advantages: Lightness, compactness
Disadvantages: There is no disc in the kit, it constantly winds up the grass (because of this, the rod near the reel with the fishing line heats up), you have to stop, remove the reel with the fishing line and clean everything with a knife. Weak plastic – the shoulder strap mount is broken. The belt itself is not comfortable. You still have to keep on weight.
Commentary: It is better to take with a double handle.

Victor K. Advantages: Low cost, collapsible bar, build quality.
Disadvantages: Not found yet.
Commentary: I was looking for Trimers for a long time so that the price was adequate and that it was more powerful and scattered for convenience during transportation. I looked through a lot of options, then the price is high, it is not collapsible, well, I stopped at this model, everything I needed in it, I just plowed the season and did fill in both the line and the mixture, I was pleased with this model.

Irina R. Advantages: Powerful enough and compact.
Disadvantages: eternal problems with ignition and, as a result, failure of the magneto
Comment: Unfortunately, the trimmer was not able to perform its direct work – it died

Anton S. Advantages: Price, simplicity, reliability
Disadvantages: Inconvenient belt, tricky and for midgets, I use it over my shoulder as a bag.
Commentary: It was assembled soundly, everything was tightened, the lubricant in the gearbox was immediately available. After a dozen uses, nothing came loose. Gasoline does not spill out (as they wrote about similar models). Starts up “with a half kick”, cuts almost any grass and small growth of bushes with a simple fishing line. The knife is useless and vibrates a lot. I am satisfied with the purchase. Would you buy again? – yes. PS: still works (more than 2 years)

Zhora G. Advantages: Disassembled for transportation
Disadvantages: Weak shoulder strap
Commentary: I was very pleased with the function of parsing the trimmer into two parts. It turns out a compact and not very heavy instrument. A rich package bundle, although not very high quality. It mows the grass, it is easy to transport even in a small car. Therefore, it is very satisfied, despite its low power.

Vladimir T. Dignity: no
Disadvantages: the power button broke after 30 minutes of operation, 2 fastening screws were unscrewed, the head with the fishing line does not self-adjust as stated
Commentary: full Deribas

Myron of Dignity: Powerful. collapsible. the weight
Disadvantages: no
Comment: I bought it for my wife, she really liked it, copes not only with grass but also with small shrubs. The season worked without breakdowns.

Dmitry Vinogradov Advantages: Convenient to use. Powerful. Reel-semiautomatic. Knife included.
Disadvantages: Heavy (compared to electric brothers). Loves to eat 🙂
Commentary: The gas trimmer was purchased in 2014 for 4.3 thousand rubles. Standard equipment, knife included. Immediately I felt the power of this monster – a meter-high thickets on virgin soil lay as if by a wave of a magic wand, despite the weeds with trunks as thick as a finger, and this with a fishing line from the kit (as a rule, they are completed with crap …) I screwed on a knife – a shrub into chips 🙂 In general, POWER! I didn’t mow much that year, there was no need. It took a mow this year

8 hectares of dense grass with weed 50-80 cm high. I bought a Husquarna line of 2.4 mm braid – generally a fire! For 8 acres, 2 liters of benzene were consumed (4 refills of 500 ml each). I do not praise this brand at all, maybe I just came across a good copy, but after winter the trimmer started up from the second jerk, smokes quite a bit, does not overheat (pah-pah) … I don’t need to mow 10 hours a day, so professional models cost 20-30 thousand rubles. I did not consider it in principle. I simply mix gasoline with oil: I fill a 500 ml container from the kit with benzene and pour 10 ml of oil into a medical syringe. Conveniently!

Artem Advantages: The trimmer is light, comfortable. Adjustable for any height and compact folds.
Disadvantages: Short wire, but you can work with an extension cord.
Commentary: Overall, I was very pleased with the purchase. I bought grass for mowing in the country and copes with this task perfectly. I mow grass quite often, so I can’t say how he will cope with large volumes.

A lawn is quite an attractive element of the site today. However, it will look good if you take good care of it. To do this, you should regularly water the area, feed it with fertilizers and cut the grass weekly. If you neglect the last condition, then rather quickly the territory will turn into dense thickets..

The cost of spare parts for a trimmer

Regardless of the quality of the tool, you may need spare parts for the Huter trimmer. Some of them will be discussed below. For example, a drum for clutching with a housing will cost the consumer 860 rubles, while the bolt for attaching the clutch housing costs only 5 rubles. A flexible shaft for a trimmer costs 600 rubles, but a container for preparing a fuel mixture will cost a symbolic amount – 50 rubles.

Reviews of the main features and advantages of the model

  • vibration damping system;
  • structural strength;
  • long service life;
  • the location of the controls on the handle;
  • easy start.

The trimmer “Huter 1900″ has a fairly impressive power, which is 1.9 kW. A knife or fishing line is used as a cutting element. The tank capacity is 0.7L and the line thickness is 2mm. Before purchasing this equipment, you should take into account that its weight is quite impressive. This is stated by many novice users. Equipment weight is 7 kg.

Reviews of the GET 1200SL electric trimmer

If you want to buy the Huter electric trimmer, then you can pay attention to the model that was mentioned in the subheading. Its cost is not so high and amounts to 5,000 rubles. The equipment, according to buyers, can be used for processing the lawn on the personal plot, as well as processing small areas. You can use the tool to cut grass even in hard-to-reach places such as along a fence or under benches.

The power of the unit is sufficient to perform tasks in everyday life and is 1.2 kW. The bar is collapsible, which, as buyers emphasize, simplifies not only storage, but also transportation. This example is ideal for women and the elderly, as the equipment is lightweight. weight is 4.5 kg.

Need a trimmer

Model operating instructions

The above-described gasoline trimmer “Huter” must be used taking into account the safety rules that are prescribed in the instructions. From them you can learn that it is unacceptable to use the equipment for people who are under the influence of alcohol or are physically tired. Before starting work, it is necessary to arm yourself with special protective equipment, among them appropriate clothing, goggles, mittens or gloves, a helmet and headphones should be distinguished. The equipment should not be used near flammable and explosive substances. This also applies to conditions under which high humidity remains..

Characteristics

Often searched Inexpensive, For giving
Trimmer type Portable
Battery operation not
Handle shape D. figurative
Trimmer head / cassette included Yes
Cassette revolutions, rpm 10000
Voltage, V 220
Mowing width (cm) 32
Line diameter 1.4
Trimmer cutting element line
Weight, kg) 2.6 m
Electric motor power, W 600
Engine location Upper
engine’s type Electric
Brand name Huter
The birthplace of the brand Germany
The country of manufacture China
Guarantee 12
Stock Pickup. 3% discount, assembly and testing for free

Instructions

Visitor reviews (0)

Description

The Huter GET-600 electric trimmer is designed for cutting soft young grass in a small area. Suitable for work on a personal plot or in a garden. Processing width. 32 cm. The main handle has a soft pad for comfortable holding of the tool.

A spool with a nylon line 1.2 mm thick acts as a cutting equipment, providing a cutting width of 32 cm.A protective cover is fixed on the lower edge of the body, at the level of rotation of the cutting line.

The switch lock prevents accidental starting. Using the optional D-handle, you can maneuver between obstacles and change the cutting angle. The position of the handle along the boom and the tilt can be adjusted. The braid can be easily disassembled into two parts for compact storage and transportation.

Electric trimmer Huter GET-600

Ask a question (faq)

Pre-sale preparation

Pre-sale preparation is a test of equipment for operability. Only competent specialists are allowed to conduct it. The procedure consists of the following steps:

  • Inspection of garden equipment and accessories.
  • Assembling equipment, if necessary.
  • Idling start.
  • Adjustment and tuning of equipment for the forthcoming loads.

High-quality preparation is the key to the effective operation of the tool in the future. The sales center staff will ensure that the preparatory steps are carried out correctly, which will ensure excellent operational results..

When you shouldn’t do pre-sales training

The preparation service is provided to buyers at their request. It should be abandoned if:

We always meet the desires of our clients!