How To Correctly Tuck Line Into The Makita Trimmer
Since we saw the choice of a trimmer in the previous article, now we will have a conversation about how to correctly fill the trimmer with fishing line, and what is the best option to choose from considerations of the criterion of work.
When you purchased a trimmer and began to use it intensively, at some point the question of changing the line will arise, since this is the most wearing out element in the tool, the rich operation of the trimmer will lead to frequent replacement of consumables.
A common type of line that fits virtually all reel types is round cord. This is an ordinary fishing line, suitable for mowing succulent grass, but it will be much more difficult to mow dead wood with it, and even more so it will not cope with shrubs.
You, the diameter with which you can mow young grass, does not exceed 1.6 mm. The thicker the thread, the more coarse grass it is able to overcome.
There are fishing lines with sharpened edges in the form of an asterisk or a square, such an option is simply adapted to mowing dry grass at this time by means of the existing sharp edges, but its drawback is greater wear and its strength is inferior to a round cord.
There are fishing lines with improved aerodynamics with corresponding dents, scales and notches, a similar product makes less noise, but it is used only on lawn mowers, since the exit of such a thread from the reel is difficult, it is used in most cases with discs on which segments are inserted. The disadvantage of such a product is its fragility..
In most cases, in gasoline trimmers with an engine power of more than 1.5 hp. use cords with an iron cable inside. This thread is perfect for cutting dry grass and small bushes. The presence of a core has a positive effect on the wear resistance of this material. The disadvantage of such a cord is its cost, which is significantly not just the existing opponents.
Tool for giving and home
Step three: complete the head assembly
Pull out the ends of the line through a pair of oval spool slots. Replace both washers and the spring (if any) with the supplied new parts. Bend both ends of the line at right angles.
The final technical touch of the process of changing the line on the trimmer is the imposition of the cap on the head, followed by fixation by pressing force and slight twisting..
Pass each end into the hole at the base of the winding drum. Install the coil in the inner area of the head, resting on the spring. Put on the cover, align with the base and lightly press downwards with a small counterclockwise rotation, place the cover on the tabs of the clips. This completes the replacement procedure..
Changing the line in the trimmer: 2 easy ways
A trimmer is a necessary and useful tool for a summer cottage and a private house. Many people own and actively use it, but not everyone knows how to replace the line in the trimmer, especially at first.
In this manual, we will walk you through the entire replacement process step by step. Looking ahead, there are two ways to line the trimmer spool. There is no fundamental difference – the difference is that in the first case one line will be refueled, folded in half, and in the second there will be two such lines.
Installing a new line on the trimmer reel
Fitting a reel with a new line is carried out in the reverse order. The procedure looks something like the following, regardless of the lawn mower model:
Replacing the trimmer line: step-by-step instructions for replacing the trimmer line
Trimmers (they are also lawn mowers) are actively used by modern society for the care of lawns and other similar objects of horticultural farms. The tool is noted for its high efficiency, despite the questionable quality of cutting grass (compared to the usual peasant scythe – earth and sky). The main advantage of trimmers (lawn mowers) is high productivity with low expenditure of physical forces of the operator. However, over time, the trimmer’s cutting element (nylon scaffolding) wears out or gets damaged, making the trimmer a useless tool as a result. Hence, the task becomes urgent – how to replace the trimmer head and how to replace the trimmer head line? Let’s consider this process using the example of lawn mowers manufactured by “Black and Decker” and others.
Coil with two working tendrils
In this type of spool, you should determine the number of grooves for winding the line, lying on the inside of the spool:
- one groove – both antennae are wound together in one groove;
- two grooves – each antenna is wound on an individual groove.
For both cases, a line with a length of 2-3 m is taken.In single-groove reels, the line is pulled into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the rod side – inside the arrow usually indicates the correct direction of winding. If there are fixing grooves, the ends of the fishing line are threaded through them or held with the fingers of the free hand, they are threaded into the through hole of the outer half of the bobbin, the spool is closed and attached to the trimmer bar.
The difference in line winding in double-groove spools is that initially a 2-5 m long line segment is folded in half (to determine the middle fold), and the fold loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each along its own groove, fixing the antennae and assembling the coil is similar to the above option with one groove.
The first execution of this procedure, perhaps, will seem long and rather laborious, but with time and experience this task will be solved much faster and easier..
The video below will clearly show how to thread the line into the trimmer spool and wind it correctly – this operation is not difficult and with some patience it will certainly be crowned with success:
ruferon-rn instructions for use for children
How to properly wind the line on the trimmer spool. how many lines to wind
When refueling the line for the first time, this process may seem quite laborious, but with time and dexterity, the task is solved much faster..
In order to refuel the line, you must:
- Take the coil, unscrew its cap. Some spools have a thread to the left, so the lid must be unscrewed in the required direction..
- Measure five meters of line;
- Fold this segment in half, that is, determine where the middle is;
- Next, place this middle of the fishing line in a special hole on the reel;
- Wind the line in the direction of the arrow;
- If there are two places for winding, then the first part of the line should be wound on one half of the reel, and the second part on the other half;
- Push both ends of the fishing line into the holes of the reel;
- Screw on the lid.
What line is used for the trimmer?
Depending on the trimmer model, the thickness of the working line is from 1.2 to 4 mm. The thicker the line diameter, the thicker and tougher the grass you can mow. The most common line thickness is two millimeters..
There are several types of fishing line:
- The most durable is rounded;
- For mowing soft vegetation – curly;
- For mowing thin grass – serrated;
- Special – fits certain trimmers.
The section of the cutting thread must match the vegetation to be cut.
If it is necessary to replace the fishing line, then it is necessary to select exactly the type that is recommended by the manufacturer of this particular trimmer model, that is, the thickness of the cutting thread should be suitable for the engine power and the size of the unit.
It is better to choose a specialized cutting thread. It is worth soaking the line for a while if you plan to replace it in the spool.
After soaking, it gains elasticity and becomes stronger..
The cutting thread can be made from different components. The most common among them is nylon.
This material is characterized by a high degree of wear resistance, the ability to withstand various temperatures and high loads..
Nylon line can be stored for a long time, it does not dry out and does not lose its strength.
Therefore, its service life can be quite long..
Lawn mower spools or heads have a different structure:
How to catch more fish? I have been active fishing for quite some time now and have found many ways to improve my bite. And here are the most effective ones:
- Bite activator. Attracts fish in cold and warm water using pheromones. included in the composition and stimulates her appetite. Sorry. that Rosprirodnadzor wants to ban its sale.
- More sensitive gear. You can find reviews and instructions for other types of gear on the pages of my website..
- Pheromone baits.
You can get the rest of the secrets of successful fishing for free by reading my other materials on the site.
- Single string. In the modification of such a trimmer, there is only one working line. This unit is used mainly for small jobs, such as trimming the grass..
- Two-stringed. They can be both automatic and semi-automatic. The package here includes two strings. This trimmer is used for mowing and clearing areas..
Instructions for correctly winding the cutting thread onto the trimmer spool:
- First of all, you need to disassemble the head. To do this, press the latch and turn the cover to the side. Next, the spool is removed.
- Measure out the required amount of cutting thread and insert it into the slot.
- Wind the line on both sides in the direction of the arrow.
- Leave the ends 15 cm long uncoiled.
- These ends fit into opposite slots.
- Then the ends are fixed in the hole on the head.
- After that, the spool is carefully inserted into the body, for this you need to slightly press on it.
- If necessary, you can pull the remaining ends of the thread out. To do this, first pull one end of the thread, and then the other so that they can easily pass through the slots on the head..
- Now you need to collect the grooves on the body and screw the cover.
- Then press the spool and try to twist it all the way. If you hear a click, the spool has clicked into place..
- Next, you need to pull the free ends of the thread to the end.
How to remove the spool from the trimmer?
To change or wind the cutting thread on the spool, it must be removed.
The complexity of its removal depends on the model of the tool:
- Low motor tool. The motor is almost at the ground here. To remove the coil, press the buttons on the side of the trimmer. After pressing these buttons, the body opens where the line spool is located..
- Curved bar trimmer. Here it is necessary to turn a special lamb counterclockwise. Then the coil and the spring in it are removed.
- Straight bar tool. The bar is held motionless with a screwdriver or other object. It is removed by turning it clockwise. Then the tool is disassembled into parts and the reel is taken out..
- If a tool with one antenna is used, then about four meters of thread will be needed. This thread is passed into a hole inside the spool, where it can be fixed. Next, one end of the line is directed in the direction of the arrow. Then the end of this thread is fixed in the groove, which is in the bobbin. This is to prevent the thread from unwinding when assembling the spool. If there are no grooves, you should hold the line with your hand and collect the bobbin.
- If a tool with two antennae is used, then first check the number of grooves present..
If there is one groove, then two tendrils will be directed into one groove. If there are two grooves, then each antenna will be directed to its own groove..
In the first case, the required amount of cutting thread is passed into the hole so that the result is threads of the same length. Then you need to turn the bobbin on the arrow. Then they begin to assemble the tool, holding the threads with your finger..
If the reel is equipped with a semi-automatic mechanism, then the line is wound as follows:
- The thread is threaded through the hole that is inside;
- Fix the ends of the thread in the grooves on the body.
- The coil is assembled and a special button is pressed;
- After which the line itself begins to dangle in the right direction..
It must always be remembered that the cutting thread must be protected from hard things. This will extend its lifespan..
If you do not adhere to this rule, you will often have to stop work, remove the spool and change the thread to a new one..
Threading the spools with thread of different types of bobbins
With two-string automatic heads:
- First you need to press the clamp until you hear a click. remove the cover.
- Rotate the spool carefully so that it can detach from the holder. Extract her.
- Measure out two lengths of cutting thread of the same length. To make further work easier, the ends of the line must be cut off at an angle. Take one end and push it into the special hole in the coil. It can also be slots, grooves, clamps, etc..
- Further, in the direction of the arrow, you need to wind the fishing line, and quite tightly and evenly. It is necessary to fix the end of the fishing line in a special eyelet on the reel..
- Subject the other half of the line to the same operation, only on the other half of the reel..
- Next, install the coil into the trimmer head. And thread the rest of the line through the hole in the head.
- Then carefully straighten the thread and close the lid. If the line turns out to be long, then it is better to cut off the excess. There should be about fifteen centimeters left on each side..
On the semi-automatic head:
- The thread is threaded through the hole that is inside;
- Fix the ends of the thread in the grooves on the body.
- The coil is assembled and a special button is pressed;
- After which the line itself begins to dangle in the right direction..
Makita Nylon Cord Movie 3_BUNP&FEED
It is necessary to very carefully and carefully thread the cutting thread into the unit, because not only the cleanliness of the garden area, but also personal safety depends on the correct winding of it..
A few tips for properly threading the string into the trimmer
- If the coil allows you to wind fifteen meters of thread, then you should not wind so much, ten is enough, that is, if you fold it in two layers, you get five meters. With a different line capacity, you should use the same rule.
- In the case when an ordinary round thread is used, it is better that it be 3.3 mm in diameter. If this is a curly fishing line, then its thickness should be less, for example, 3 mm.
- It is better to wind both segments of the fishing line on the spool at once, and it is necessary to start from its bend. It is important not to overlap in the direction of the arrow. It is also important to be able to pull the thread perfectly. If the thread is over-tightened, then it can overlap. If not enough, it can twist. In order not to cut your hands on the curly thread yourself, you should wind it with gloves.
- No need to leave the ends of the line long. This can cause it to curl..
Now only I bite!
I caught this pike with a bite activator. No more fishing without a catch and looking for excuses for your bad luck! It’s time to change everything. The best bite activator of the year! Made in Italy.
Googled the Forum, there is an old topic, but very little specifics. It may be possible to collect material useful for members of the forum.
lawn mower Stihl FS55, is in operation for the second season. When buying under the action, the set included a Stihl AutoCut 25-2 mowing head with an orange 2.4 mm line. Line with a spiral groove. proved to be great. Enough for the season. Mow 6 acres 6 times and pass through the forest to the stream. 30 x 1.5 m.
When the “native” line ended, in Leroy Merlin for 117 rubles. bought an acid orange translucent line with a spiral groove 2.4 mm x 15 m McCulloch NL0014 (blister). The fishing line is soft, cuts well, but it is consumed several times faster, often breaks off “to zero”. for one mowing of six acres of young grass, almost complete winding was left. 15 meters was not enough for 2 mows.
I bought a Chinese round crimson fishing line 2.4 mm x 15 m Crazy Stone for 67 rubles. noisier than both previous ones, but cuts well, breaks on the ground and roots. The consumption is still the greatest. mowed her only once. less than half of the spool left.
Now aimed at the Oregon line.
Registration: 20.04.2010 Ekaterinburg Posts: 450
06/18/2015 at 15:00
levian wrote.
often breaks off “under zero”
read advice somewhere, it is recommended to soak in water before use.
lawn mower Stihl FS 90 I use a reel into which plastic knives and 0.5 meter line are inserted.
I did not like the young, not tall grass stroking, but already cuts a large one.
I use echo 2.5mm titanium ok.
”
I compared P.I.T 2.4mm line and 2.5mm echo for about the same flow rate.
I didn’t like twisted 3mm line echo, I didn’t like the young, tall grass, but cuts the big one
“
Instructions for refueling the gas trimmer line. 150 cm?
In order for the trimmer to work “like a clock”, it is necessary to choose the right line, that is, choose it taking into account the trimmer model and the type of work. There are two important parameters in this matter. this is the diameter and section.
The diameter of the fishing line must correspond to that recommended for this model (it must be specified in the product passport).
The cross-section of the fishing line is round, square, with sharp edges (pentahedron). A round line is designed for mowing young grass and lawn, square and pentagonal line will come in handy if the grass is coarse and weeds have grown on the lawns.
Trimmer head modification
Trimmer mowing heads can be of various modifications: single-line for trimming the lawn (mows with one line of fishing line); two-string for mowing grass and land clearing with automatic line feed or manual string length adjustment.
Makita – How To: Replace Nylon Line Cord
Modern growers are increasingly offering gardeners universal trimmers with two-line automatic mowing heads..
Step-by-step instructions for threading the line into the trimmer
- Press the clips inward until they click and remove the cover from the mowing head..
- Turn the spool carefully, it will free itself from the holder, and now remove it.
- Cut two identical pieces of line (the edge of the line should be cut at an angle. This will make the job easier). Take one of them and insert the end of the line into a special pocket on the reel (there may be hooks, ears, clips). Then wind the string in the direction of the arrows. Spread the line evenly, tightly. Attach the end of the string to the specially provided hole in the reel..
- Do the same operation with the second part of the line, only thread the end on the spool from the opposite side.
- Return the line spool to the mowing head. Pull out the ends of the line through the holes in the spool and thread them into the special connector of the head.
- Spread out the line carefully and close the lid. Cut the excess fishing line, leaving 12-15 cm at each edge.
All is ready. The trimmer is loaded with line and ready to go. Now you can happily start mowing your favorite meadow, summer cottage, local area.
It is only important to remember that not only the quality of the work performed, but also your safety will depend on how you load the cutting line into the trimmer.
Video instruction for refueling the gas trimmer line (lawn mowers)
Similar posts
instructions for winding lawn mowers:
lego airplane assembly instructions
lawn mower line winding instructions
How to thread the line into the trimmer spool and which one is better to use for this?
January 24, 2014
Very often, those people who personally own dachas and vegetable gardens are faced with the need to care for the lawn on the site. In such cases, you simply cannot do without the usual manual braid or trimmer. The first is slowly fading into the background, and the number of people who use it is getting smaller and smaller. The trimmer works automatically and does not require a lot of effort. Moreover, you do not need to have a special skill to use it..
How the trimmer works?
The principle of operation of such a device is that the grass is cut by a special fishing line installed on a fast-rotating head. The number of revolutions per minute can reach 8000. In a short time, the line becomes unusable, more precisely, it is erased. Then summer residents have a question: “How to fill the line in the trimmer coil”?
Types of trimmer lines
First of all, in order not to resort to frequent replacements, it is better to use a denser line. The number of its types and manufacturing firms is simply amazing. The main parameter of the trimmer line is its diameter. It varies from 1.6 to 3.2 mm. The most common type is 2mm line. However, its selection must be made depending on the type of trimmer you have..
There are several options for the section of the line. So, it can be round, square, in the form of an asterisk with sharp edges. The last option is the most effective. However, it should be used only on powerful braids and at the same time you need to know how to thread the line into the trimmer spool. Therefore, we can conclude that the more powerful your lawn mower, the thicker the line should be..
A process such as winding a fishing line on a trimmer is not difficult, but it has its own characteristics. First, you need to choose the right fishing line, the diameter of which is prescribed in the device’s passport.
First, unscrew the spool cap. Be careful, as the thread can be left or right. The left-hand thread is necessary so that the head of the scythe does not unwind during operation.
Threading the line into the trimmer
Before threading the line into the trimmer spool, measure 5 m from the skein (this is the average amount of line installed on trimmers). Then fold it in half to find the middle. The resulting center must be inserted into a special slot located on the spool. After that, wind the line in the direction of the arrow on the head.
There are such models in which the winding place is divided into two halves. Therefore, one is often wound clockwise, and the other. vs. Having reeled the fishing line completely, the ends are threaded through special holes. A cap is put on top of the head.
From the above it follows that the process of replacing the fishing line itself is not difficult. Having carried out such a manipulation as winding a fishing line on a trimmer reel several times, you will bring this process to automaticity. The only thing is that you need to constantly monitor the condition of the fishing line in order to avoid breaking it at the time of work on the site, when a spare coil may not be at hand.
Now you know how to thread the line into the trimmer spool, and you can do it yourself without much effort.!