How to replace the line in the Stihl trimmer spool

How to put line in the Stihl.FS-38 mower

took out the mower from the barn, but there was no line in it, I had to put the line and on the occasion took off a small

How to correctly replace the line in the mowing head, reel of Stihl FS 55 lawn mowers

Coil with two working tendrils

In this type of spool, you should determine the number of grooves for winding the line, lying on the inside of the spool:

  • one groove. both antennae are wound together in one groove;
  • two grooves. each antenna is wound on an individual groove.

For both cases, a line with a length of 2-3 m is taken.In single-groove reels, the line is pulled into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the rod side. inside the arrow usually indicates the correct direction of winding. If there are fixing grooves, the ends of the fishing line are threaded through them or held with the fingers of the free hand, they are threaded into the through hole of the outer half of the bobbin, the spool is closed and attached to the trimmer bar.

The difference between the line winding in two-groove spools is that initially a 2-5 m long line segment is folded in half (to determine the middle bend), and the bend loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each along its own groove, fixing the antennae and assembling the coil is similar to the above option with one groove.

The first execution of this procedure, perhaps, will seem long and rather laborious, but with time and experience this task will be solved much faster and easier.

The video below will clearly show how to thread the line into the trimmer spool and wind it correctly. this operation is not difficult and with some patience it will certainly be crowned with success:

Coil with one working tendril

The simplest option and uncomplicated sequence of actions:

  • The dimensions of the reel and the length of the original factory winding determine the recommended length of the line for winding. 2. 5 m.
  • One end of the line is inserted into the fixing technological hole located inside the spool.
  • The fishing line is wound on the drum in the opposite direction of the spool rotation on the trimmer product. as a rule, on the inside of the reel, an arrow indicates in which direction the winding is carried out.
  • A small section of the line is left free to lead it out. it is fixed in a specialized groove on the inside of the bobbin, designed to hold the winding when assembling the bobbin into working condition.
  • The left end of the line is passed through the hole in the outer part of the reel.
  • The bobbin halves are assembled and put on the trimmer bar.

replace, line, stihl, trimmer, spool

Automatic line winding on a spool

There is a type of reel in which the automatic mechanism winds without the help of others. from the user it is enough to just fill the line correctly. How do I load the line into the trimmer spool? Video instruction. How to remove the spool from the trimmer? How to wind the line in order to tuck the line. The fishing line is passed through a hole on the inside of the body, its antennae without winding are passed through the hole on the outer body, the reel is assembled, and when the winding button is rotated, the fishing line is wound from the inside without the help of others. In such a spool, it is unrealistic to make the winding wrong: the mechanism itself will determine the correct direction, since it can only rotate in one direction.

The warranty production of the factory trimmer refueling will inevitably require line replacement. Having a very rough idea of ​​how to thread the line into the trimmer reel on their own, beginners are reluctant to take up this business. However, with some skills, mastering this simple science does not present any difficulties, and the similar instruction presented below will make this process as easy as possible.

We carry out the winding of the fishing line

Sluggishly completed disassembly of the spool-spool without losing its spare parts allows you to proceed to the main task. winding the fishing line into the spool. Technological features of the spool design and the number of working antennae determine the sequence of actions.

Preliminary preparation

First, to wind the fishing line, you need to remove the spool (bobbin, spool) from the trimmer. certain actions will depend on the complexity of the configuration and the type of the product itself:

  • small electronic trimmers with a working position of the motor and coil at the bottom usually have side buttons on both sides of the bobbin. When pressed at the same time, the upper part of the reel, together with the inner content for winding the line, is disconnected, while the lower part remains on the trimmer. It is better to parse the bobbin on a flat, smooth place so that the spring included in the structure does not jump out and is not lost;
  • Electronic and gasoline trimmers with a curved bar without the ability to install a knife, usually have spools with a special wing: in similar designs, hold the spool in a fixed position with one hand, and turn the locking reel on the rod with the other counterclockwise with the wing nut. How do I fit the line into the trimmer? How to thread the line into the trimmer spool. It is clear how to load the line on the trimmer. After disconnecting the nut, the entire bobbin is removed.
  • electronic and gasoline trimmers with the ability to install a knife on a straight bar (for example, Stihl trimmers) have a hole under the reel. For the rod to remain stationary, a screwdriver or other suitable object is inserted into this hole, and with unhurried rotation, such mutual placement is achieved when the screwdriver goes inside the hole, and the bobbin is fixed. After that, the coil body is scrolled clockwise (with left-hand thread) and removed from the trimmer.

For the second and third options, the coils, depending on the design, are disassembled by different methods. In bobbins with a lamb, a lamb is turned inside out, in coils with latches, the latches are pressed and one part of the coil is released from the other. How to fill the line in how to properly cheap line. 2. On your site. If the halves of the spool are connected by thread, then it is enough to turn them by hand in the opposite directions until they are completely unscrewed.

Automatic line winding on a spool

There is a type of reel in which the automatic mechanism winds without the help of others. from the user it is enough to just fill the line correctly. How do I load the line into the trimmer spool? Video instruction. How do I remove the spool from the trimmer? How to wind the line in order to tuck the line. The fishing line is passed through a hole on the inside of the body, its antennae without winding are passed through the hole on the outer body, the reel is assembled, and when the winding button is rotated, the fishing line is wound from the inside without the help of others. In such a spool, it is unrealistic to make the winding wrong: the mechanism itself will determine the correct direction, since it can only rotate in one direction.

The warranty production of the factory trimmer refueling will inevitably require line replacement. Having a very rough idea of ​​how to thread the line into the trimmer reel on their own, beginners are reluctant to take up this business. However, with some skills, mastering this simple science does not present any difficulties, and the similar instruction presented below will make this process as easy as possible.

Coil with two working tendrils

In this type of spool, you should determine the number of grooves for winding the line, lying on the inside of the spool:

  • one groove. both antennae are wound together in one groove;
  • two grooves. each antenna is wound on an individual groove.

For both cases, a line with a length of 2-3 m is taken.In single-groove reels, the line is pulled into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the rod side. inside the arrow usually indicates the correct direction of winding. If there are fixing grooves, the ends of the fishing line are threaded through them or held with the fingers of the free hand, they are threaded into the through hole of the outer half of the bobbin, the spool is closed and attached to the trimmer bar.

The difference between the line winding in two-groove spools is that initially a 2-5 m long line segment is folded in half (to determine the middle bend), and the bend loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each along its own groove, fixing the antennae and assembling the coil is similar to the above option with one groove.

The first execution of this procedure, perhaps, will seem long and rather laborious, but with time and experience this task will be solved much faster and easier.

The video below will clearly show how to thread the line into the trimmer spool and wind it correctly. this operation is not difficult and with some patience it will certainly be crowned with success:

Preliminary preparation

First, to wind the fishing line, you need to remove the spool (bobbin, spool) from the trimmer. certain actions will depend on the complexity of the configuration and the type of the product itself:

  • small electronic trimmers with a working position of the motor and coil at the bottom usually have side buttons on both sides of the bobbin. When pressed at the same time, the upper part of the reel, together with the inner content for winding the line, is disconnected, while the lower part remains on the trimmer. It is better to parse the bobbin on a flat, smooth place so that the spring included in the structure does not jump out and is not lost;
  • Electronic and gasoline trimmers with a curved bar without the ability to install a knife, usually have spools with a special wing: in similar designs, hold the spool in a fixed position with one hand, and turn the locking reel on the rod with the other counterclockwise with the wing nut. How do I fit the line into the trimmer? How to thread the line into the trimmer spool. It is clear how to load the line on the trimmer. After disconnecting the nut, the entire bobbin is removed.
  • electronic and gasoline trimmers with the ability to install a knife on a straight bar (for example, Stihl trimmers) have a hole under the reel. For the rod to remain stationary, a screwdriver or other suitable object is inserted into this hole, and with unhurried rotation, such mutual placement is achieved when the screwdriver goes inside the hole, and the bobbin is fixed. After that, the coil body is scrolled clockwise (with a left-hand thread) and removed from the trimmer.

For the second and third options, the coils, depending on the design, are disassembled by different methods. In bobbins with a lamb, a lamb is turned inside out, in coils with latches, the latches are pressed and one part of the coil is released from the other. How to fill the line in how to properly cheap line. 2. On your site. If the halves of the spool are connected by thread, then it is enough to turn them by hand in the opposite directions until they are completely unscrewed.

How to put line in the Stihl.FS-38 mower

took out the mower from the barn, but there was no line in it, I had to put the line and on the occasion took off a small

We carry out the winding of the fishing line

Slowly completed disassembly of the spool-spool without losing its spare parts allows you to proceed to the main task. winding the fishing line into the reel. Technological features of the spool design and the number of working antennae determine the sequence of actions.

How to correctly replace the line in the mowing head, reel of Stihl FS 55 lawn mowers

Coil with one working tendril

The most common option and easy sequence of actions:

  • The dimensions of the reel and the length of the unique factory winding determine the recommended length of the line for winding. 2. 5 m.
  • One end of the line is inserted into the fixing technological hole located on the inside of the spool.
  • The fishing line is wound on the drum in the reverse rotation of the spool on the trimmer product direction. usually, on the inner side of the bobbin, an arrow indicates in which direction the winding is being carried out.
  • A small section of the fishing line is left free to bring it out. it is fixed in a special groove on the inner side of the bobbin, created to hold the winding when assembling the bobbin into working condition.
  • The left end of the line is passed through the hole on the outside of the bobbin.
  • The bobbin halves are assembled and put on the trimmer bar.

Preliminary preparation

First of all, to wind the fishing line, you need to remove the spool (bobbin, spool) from the trimmer. specific actions will depend on the complexity of the configuration and the type of the product itself:

  • small electric trimmers with a working position of the engine and spools at the bottom, as a rule, have side buttons on both sides of the bobbin. When pressed at the same time, the upper part of the spool together with the inner content for winding the line is detached, while the lower part remains on the trimmer. It is advisable to disassemble the bobbin on a flat, smooth place so that the spring included in the structure does not jump out and is not lost;
  • electric and gasoline trimmers with a curved bar without the possibility of installing a knife, as a rule, have spools with a special wing: in such designs, hold the spool in a stationary position with one hand, and rotate the locking reel on the bar with the wing nut counterclockwise with the other. After disconnecting the nut, the entire bobbin is removed.
  • electric and gasoline trimmers with the ability to install a knife on a straight bar (for example, Stihl trimmers) have a hole under the reel. To keep the rod stationary, a screwdriver or other suitable object is inserted into this hole and, with slow rotation, such a mutual position is achieved when the screwdriver enters the hole and the bobbin is fixed. After that, the coil body is scrolled clockwise (with a left-hand thread) and removed from the trimmer.

For the second and third cases, the coils, depending on the design, are disassembled in different ways. In bobbins with a lamb, a lamb is unscrewed, in coils with latches, the latches are pressed and one part of the coil is released from the other. If the halves of the bobbin are connected by thread, then it is enough to turn them by hand in opposite directions until they are completely unscrewed.

How to change the line in the trimmer and which one is better to choose

Since we considered the choice of a trimmer in the previous article, today we will tell you how to properly fill the trimmer with fishing line, and which one is better to choose based on the working conditions.

After you bought a trimmer and began to actively use it, sooner or later the question of replacing the fishing line will arise, since this is the most wearing element in the tool, intensive use of the trimmer will lead to frequent replacement of consumables.

HOW-TO. Stihl String Trimmer Head Replacement

What types of woods are there

The most common type of line that fits almost all reel types is round cord. This is an ordinary fishing line, suitable for mowing succulent grass, but it will be much more difficult to mow dead wood with it, and even more so it will not cope with bush.

As a rule, the diameter that can be used to cut young grass does not exceed 1.6 mm. The thicker the thread, the more coarse grass it is able to overcome.

There are fishing lines with sharp edges in the form of an asterisk or a square, this option is more adapted to mowing dry grass precisely due to the existing sharp edges, but its disadvantage is greater wear and tear and it is inferior in strength to a round cord.

There are fishing lines with improved aerodynamics with characteristic dents, scales and notches, such a product makes less noise, but it is used only on lawn mowers, since the exit of such a thread from the spool is difficult, it is used most often with discs into which segments are inserted. The disadvantage of such a product is its fragility.

Most often in gasoline trimmers with an engine with an output of more than 1.5 hp. use cords with a metal cable inside.

This thread is ideal for cutting dry grass and small bushes. The presence of a core has a positive effect on the wear resistance of this material.

The disadvantage of such a cord is its price, which is significantly higher than the listed opponents.

How to remove or tuck the line into the trimmer

In order to wind the line, it will take about 10-15 minutes. What is a trimmer coil? Plastic body with a cassette inside, on which there is a special hook for easy winding of the fishing line.

How To Change Your String On A Stihl String Trimmer Bump Feed

Almost all trimmer reels have a similar fastening principle, this is a central screw-button, when pressed, it becomes possible to pull out the line of the required length. The photo below shows a few examples of different trimmer spools.

The bobbins of the trimmers, the motor of which is located at the very ground, have a different attachment to the axis of rotation, they have two buttons on the spool located on the sides that need to be wrung out, otherwise the replacement of the thread is no different from other cassettes.

The principle of correct winding of the fishing line is similar in all of the above cases, therefore, for example, consider the standard version with two antennae.

To remove the spool with the fishing line, you need to unscrew the centrally located screw, but note that the thread is left there, so you will have to turn it clockwise, this was done on purpose so that during operation it does not open under the influence of centrifugal force.

Next, using a screwdriver, disassemble the head and remove the spool onto which the fishing line is directly wound.

Having measured the required length and folded in half, you need to tuck the fishing line into the spool, eventually bringing its ends opposite each other (for this there are special slots for fixing).

After that, it is necessary to assemble the head in the reverse order, threading the ends of the cord into two corresponding holes.

If you have doubts or it is not entirely clear how to load the line on the trimmer, we recommend that you look at how to properly wind the line into the lawn mower.

In this video, in detail, step by step, the instructor will open the trimmer head, measure the required amount of line, usually from two to four meters, and demonstrate assembly and installation on the trimmer.

Electric version of the scythe

The self-propelled form of these units can be used anywhere, but only next to the power supply. Quiet, they are often used near schools, kindergartens, as well as hospitals and clinics. They are used quite actively on private territory.

The models are easy to operate, have a low noise level, high reliability, and also an affordable price.

Trimmer coil device

Trimmer mowing heads come in a variety of designs, both simple and complex. The picture below shows an exploded view of the semi-automatic trimmer head from a Husqvarna (Husqvarna) lawn mower.

This type of head is found on most lawn mowers and trimmers such as Stihl (Stihl), Patriot (Patriot), Champion (Champion), Bosch (Bosch), Huter (Huter) and others. The device of the mowing head is quite simple. It includes the following details:

  • mowing head base;
  • button for semi-automatic cord feed;
  • bobbin (spool) into which the fishing line is tucked;
  • spring;
  • eyes. through them the line comes out;
  • trimmer head cover;
  • line (cord).

There are also simpler trim heads shown in the following photo.

All these attachments do not allow you to change the length of the line in a semi-automatic mode (after pressing a button). If the cord breaks, you have to stop the mower and change it manually.

How to remove the spool from the Stihl trimmer

Stihl’s garden equipment has long established itself on the agricultural market. Electric trimmers of this company are distinguished by quality, reliability, stable operation even under high load. The Stihl electric kos lineup is easy to use and easy to maintain. This gives an excellent opportunity to use the technique even for a beginner.

FSE 52

The mechanism is hinged, due to which the device tilts in different directions. The cutter spool can be positioned perpendicular to the ground. There are no ventilation slots, which protects the device from water ingress, so the grass can be mowed in the early morning (when there is dew) or immediately after rain.

Cordless lawn mower

Ideal for those who do not want to breathe gasoline exhaust, and also depend on electricity. The machine consists of a sturdy polymer body and a compact grass catcher. The volume of the grass catcher depends on the model.

Such devices are silent, reliable and safe to use.

FSA 65

The length of the device is 154 cm. The current is 5.5 A. The lightest of the other mowers. This tool can be used over large spaces.

FSA 85

The length is 165 cm. The current is 8 A. Ideal for mowing in a small area.

Convenient device for mowing a lawn, a flower bed, a fence, etc. The engine is quiet enough, there is no exhaust gas.