How to saw an angle grinder wood with a disc for wood

How to cut wood angle grinder

Support

If we cut wood with a hand-held circular saw, then we rest the tool against the workpiece and simply push it forward along the intended mowing line. The tool disc does not lead to the right or left as the support prevents the disc from beveling. In the case of, for example, a stationary circular machine, it is still easier, the disc is fed across the table and again, resting it on the table, we do not allow the workpiece to tilt to the right or left. In the case of an angle grinder, the disc has no support, except our unsteady hand.

Different speed of rotation

Here one could say about the speed of rotation, but that would not be entirely correct. Let me explain why. Even the angle grinder, large and small, has different rotational speeds. And all because you need to ensure the same linear speed of rotation. That is, the larger the disc, the slower the tool must rotate so that there is the same linear rotation speed. So, for an angle grinder, on average, the linear speed of rotation is 80 meters per second, and for a circular saw, this value is on average 60 meters per second. And if the angle grinder does not have a rotational speed regulator, then it will at least burn wood, as a maximum, read on.

Milling with an angle grinder

Another operation that many experienced craftsmen successfully perform with this tool is milling. Unlike a router, you will not be able to perform really high-quality processing. However, making a groove, as well as cutting a small part. it will turn out to be quite tolerable.

Again, this operation is dangerous. I have already written recommendations for general action using this tool, so follow them. an angle grinder needs a thick and high quality cutter. Immediately dismiss the possibility of using homemade nozzles, give your choice to an old brand, insured against chips and breaks.

Even with all the tips, a beginner alone should not start milling without the supervision of a more experienced craftsman. As mentioned above, accidents constantly occur with the masters of their craft, given the instability of the tool.

And why then you can saw with a hand-held circular saw?

Here the keyword is. support ! If we cut wood with a circular saw, then we rest the tool on the workpiece and simply push it forward along the intended mowing line. The tool disc does not lead to the right or left as the support prevents the disc from beveling. In the case of, for example, a stationary circular machine, it is still easier, the disc is fed across the table and again, resting it on the table, we do not allow the workpiece to tilt to the right or left. In the case of an angle grinder, the disc has no support other than our unsteady hand.

That is, if we are sawing with a circular saw, then we push the tool with our shoulder against the material, if we work with an angle grinder, then we simply hold the tool “in the air” with the force of our brushes (which, in an emergency, most likely will not be enough).

In addition, an angle grinder rotates much faster than a circular grinder, an angle grinder has an average linear rotation speed of 80 meters per second, and a circular saw this value is on average 60 meters per second.

an angle grinder can cut metal, but not wood?

Such a natural question arises in the minds of many. Some of my acquaintances even voiced this question. I’ll try to explain the difference. So, let’s take a look at the metal cutting disc:

In this photo on the left, a cutting disc for metal, the one that is thin. I put a thick disc for contrast, it is used only for grinding metal.

There are several reasons why metal is cut with a thin disc:
  • the thinner the cut, the easier the tool enters the material;
  • the thinner the cut, the less stress on the tool and on the operator;
  • security.

Within the framework of this publication, we are interested in the third point. When you cut, metal, there is always the possibility that the disc will jam. If you are using a thick disc, the tool will rip out of your hands. In the case of a thin disc, it will most likely fly apart, and if a protective casing is installed, and we have protective glasses, or even better a mask (and you also cut with sparks from yourself), then you are not afraid of the fragments by 95%.

Now remember the photo of the disk for the tree from the beginning of the article. It is a steel, thick disc that will not fly apart when the disc is clamped. Therefore, the tool will most likely simply snatch from your hands.

And even if the disc is not clamped, wood is a heterogeneous material. Soft fibers give way to hard ones, and there are bumps between them, and you may simply not hold the tool when it enters the bit.

Grinding: attachments and process

Sanding pads are discs that are produced by layering several different coatings. To improve the abrasion characteristics of the treated surface, the initial layer is made of rubber, sometimes it is replaced with hard plastic. The layer of the second level of the nozzle allows to ensure the adherence of the plane of the working part to the surface to be grinded; it is made of foam rubber. The main, working layer is a sheet of sandpaper.

The use of sanding pads allows you to work efficiently with already painted surfaces. Rough polishing of the untreated surface is also possible.

Flap-type discs are suitable for the same purposes, only in rough grinding it turns out faster. A disc of this type is sandpaper petals attached to the working surface of the disc.

To remove paint, it is best to take special devices with peeling functions. Steel cup, with fastened steel fibers made of hard wire, excellent abrasion, additionally sanding wood.

The device and capabilities of the angle grinder

Arranged angle grinder (angle grinder) is quite simple. The electric motor, by means of a bevel gear, transmits rotation to the shaft, on which replaceable nozzles are fixed. The area of ​​use of the angle grinder is extremely wide. It is used for cutting, stripping, roughing, grinding and sharpening. The type of work performed is determined by the functionality of the removable disks. Each angle grinder accessory has its own purpose.

Such a tool is used during construction work, in mechanical and repair shops, during rescue work and in other areas of activity. an angle grinder is indispensable both in everyday life and in production. We also recommend it

Sawing firewood angle grinder

Sawing wood with an angle grinder can be relatively safe. It provides for a rigid attachment of the cutting equipment to a bed with guide elements. This will be a stationary sawing equipment in which the angle grinder is securely fixed. The self-made machine works on the principle of circular saws, where the processed material is fed along the guides.

You can cut firewood with an angle grinder, but you need to use the devices necessary to ensure safety. A jigsaw, circular saw, hand tools are more suitable for working with wood.

angle, grinder, wood, disc

Discs for wood on an angle grinder

The angle grinder is used for working with hard materials and is not a specialized tool for processing wood. But you can use it for these purposes, although you will have to comply with some conditions. It is strongly discouraged to use the standard equipment, because it’s not safe.

The industry produces a range of specialized wood discs recommended for the angle grinder:

  • Cut-off discs have specially shaped teeth and reamers located on the cutting part to prevent jamming of the tool.
  • Chain discs are designed for modeling, milling and stripping wood. They are a disc made of high-alloy steel, on the outer edge of which a chain from a chainsaw is installed.
  • Special flap sanding attachments are designed for smoothing irregularities and cleaning. Such a nozzle consists of several layers of sandpaper stacked radially one on top of the other so that they overlap.
  • The disk plane is used for rough processing of wood blanks, for example, in the construction of a log house. This attachment replaces the carpenter’s ax.
  • Wood cutters allow for rough milling work.
  • End discs are used to level the end surface.
  • Sanding disc for wood with interchangeable sanding discs of various grain sizes.
Read more:  How to Check Anchor And Stator Angle Grinder

Can an angle grinder safely cut wood?

There is an angle grinder in almost every home, it is difficult to imagine carrying out many types of repair work without it. This multifunctional tool can cut various materials: brick, concrete, metal, porcelain stoneware, etc. The question of whether an angle grinder can cut wood is a matter of controversy.

Basic safety instructions

Before cutting wood with an angle grinder, read the safety instructions. The main of these rules are as follows:

  • Be sure to use personal protective equipment (protective plastic glasses, fabric gloves), work in overalls.
  • Never use defective discs.
  • It is recommended to hold the angle grinder firmly with 2 hands.
  • Always make sure that the power cord is not close to the rotating disc.
  • Place the angle grinder only after the cutting element has come to a complete stop.
  • Do not remove the protective cover.
  • Not working while intoxicated.

Do not use accessories that are not intended for work with an angle grinder. You should not use cutting equipment for circular saw blades for the following objective reasons:

  • The angle grinder has a higher rotational speed than a circular saw. The disc is designed for lower revolutions, therefore, at high speed, it can crack and fly apart. Flying fragments can be harmful to health.
  • The wood has a more viscous texture and inclusions in the form of knots, because of this, the teeth enter the material unevenly. If the disc gets stuck, the tool could be pulled out of the hand, resulting in serious injury.
  • Due to uneven loads, the equipment overheats and a failure is possible.

Wood cutting angle grinder

In the absence of special equipment for working with wood, it is allowed to cut wood with an angle grinder. But the thickness of the material cut by the angle grinder should not be more than 4 cm.It is necessary to use special cutting discs and wood cutters recommended for working with an angle grinder.

Hold the cutting tool perpendicular to the work surface. If it is possible to adjust the speed of the angle grinder, then set the minimum value. The recommended maximum values ​​must not be exceeded (the corresponding marking is on the disc). When cutting at high speeds, the wood starts to burn, a large amount of smoke is emitted.

It is not recommended to use the button lock during operation in order to be able to turn off the device and minimize possible damage. In order for the tool not to jerk at the end of the cut, experts advise first to file the workpiece along the edges, and only then cut it.

Grinding and polishing

For grinding and polishing wooden products, a tool is better than an angle grinder. it has good performance and is capable of providing high quality work performed. With an angle grinder, you can perform the entire cycle of processing wood surfaces: from roughing to finishing polishing.

To carry out these works, special grinding attachments are used. The quality of the product depends on how correctly the wheel is selected for the angle grinder. These attachments differ in shape, material and purpose.

For rough processing (roughing), the following types of nozzles are used:

  • a roughing circle. a steel disk on which pieces of metal wire are soldered;
  • cord brush. a disc with a wire pile (there are different hardness);
  • end disc.

For polishing and final grinding of the nozzle, other nozzles are used:

  • petal;
  • grinding;
  • cup. brushes made of special abrasive nylon.

The angle grinder is not suitable for sawing or cutting wood. The use of an angle grinder for these works is not recommended, but under certain conditions, a small amount of work is allowed.

Chain disc or cutter

This version of the nozzle has a device that allows you to rotate it even when biting the chain mechanism, eliminating the possibility of a sudden jerk.

With the help of such a cutter, you can make notches in a log, remove bark, cut out complex relief on the surface.

In principle, it is possible to saw with a chain disk if it has a diameter of 23 cm, only such a nozzle will cost a lot.

Saw blade with few teeth

Please note that on the surface of such a disc, the manufacturer applies information about the maximum number of permissible revolutions.

Large tooth spacing makes woodworking safer

Such discs, in addition to wood, do a good job with aerated concrete blocks.

Tungsten Carbide Discs

Such attachments have appeared relatively recently and have already become very popular. The reason is that they easily deal with small metal inclusions at high revs.

This is perhaps the only option for a nozzle that will definitely cope with sawing, without any unpleasant nuances.

For your information! Rotarex discs are in great demand, which can be used for sawing wood.

In addition to the actual discs for woodworking, there are other attachments for the angle grinder.

What attachments can be used for working with wood

As already mentioned, not every attachment is suitable for this task. Don’t risk using wilds that are not designed for woodworking. Possible attachment options are shown below.

What is the danger of working with an angle grinder

Any power tool is potentially dangerous, especially to those who neglect safety and protection measures during work. What’s dangerous about an angle grinder:

  • angle grinder attachments rotate at a very high speed: more than 10 thousand revolutions per minute;
  • most of the rotating disc is not protected by a cover;
  • when cutting the material, small fragments and sawdust are often formed, which fly away at high speed to the sides;
  • a powerful device is quite difficult to hold in your hands, especially if the material for cutting has a complex structure.

When choosing cutting wheels, remember that they are quite fragile and can crack and fly apart during operation.

Advice! When choosing attachments for an angle grinder, pay attention to their condition: they should not have any defects. The slightest unevenness or chipping can lead to sudden destruction of the material during operation.

The slightest misalignment leads to jamming of the nozzle. Because of this, a powerful jerk occurs during work, which can knock the tool out of the hands.

Advice! If you don’t have experience with an angle grinder, don’t go for a powerful professional model. Better take a household appliance with a disc diameter of up to 125 mm.

What can you do with an angle grinder?

Angle grinder, in common people an angle grinder, is capable of performing many operations.

The more powerful the engine, the higher the professional class of the device. For ease of use, high-quality models are equipped with handles that allow you to securely fix the tool during operation. Household models operate on a regular network. A professional tool requires a three-phase power supply at 380 V.

What operations does an angle grinder perform:

  • cutting;
  • polishing;
  • grinding;
  • sharpening.

angle grinder can work with different materials: concrete, metal, wood, brick and ceramics, stone, plastics.

The versatility of this tool is due to the use of a variety of attachments, each of which is designed for its own type of operation.

For the convenience of work, the angle grinder can be permanently mounted with special fasteners on the working surface. Some models are equipped with adjustable disc rotation speed.

Why is an angle grinder difficult to process wood?

First of all, it should be noted that the high speed of rotation of the disc distinguishes the angle grinder from the circular saw. And even the presence of a compensating ring that comes with the disc does not completely solve the problem. But if your angle grinder has a speed control, then this partly makes the task easier.

You can adjust the tool so that its speed matches the speed of the circular, this will also reduce the risk of injury to the process

But the main difficulty lies not in this, but in the structure of the wood itself, which is often heterogeneous and knotty. In addition to multidirectional fibers, there is resin in the tree, there may be pellets or ingrown wire, which you will not immediately notice. In general, wood is an unpredictable material. During work, you may encounter an unexpected obstacle, and, as a result, a jerk that can knock the tool out of your hands and direct it along a dangerous vector.

If the disc meets a piece of metal, a tooth can fly out of it, which, like a bullet, can also rush in an unpredictable direction. You are lucky if it comes across a protective cover on the way.

If you are thinking of sawing a wood angle grinder in the area, you will have to keep it in a horizontal position. This will make the grip uncomfortable and increase the risk of injury.

Important! It is strongly not recommended to cut wood with a tool that does not have a speed control and attachments that are not intended for this purpose.

Things to remember when working with an angle grinder for wood

The most important thing that many people sin is, in no case should you remove the protective cover, no matter how much you would like to see the cut point. The destruction of the disc can occur at any moment, and the fragments will fly not only at the operator, but also at those around him, and at such an incredible speed that no one has time to react.

  • you need to check the strength of the fastening of the protective cover;
  • the integrity of the disks should be checked, excluding those that have chips or cracks;
  • The angle grinder must be held so that the protective cover is on the operator’s side;
  • when starting work, it is necessary to check the tool at idle speed at different speeds. The tool should be vibration-free;
  • before work, it is worth inspecting the tree for the presence of knots;
  • hold the angle grinder firmly with both hands;
  • take a break from time to time looking at the disc;
  • if the angle grinder is stuck, turn it off immediately;
  • choose a stable body position during work;
  • make sure that the cord does not get under the disc;
  • only move with the tool switched off.
Read more:  How To Unscrew A Disc On An Angle Grinder With A Wrench

Remember, you need to work with such a tool only in a concentrated, adequate state. Use protective gloves, mask and goggles

Wood cutting, is it worth starting?

Young craftsmen are always interested in whether it is possible to saw boards with an angle grinder? I will answer immediately. No! Although such an operation is permissible for many, it should be carried out very carefully, because any violation of caution, disregard of the safety rules, can lead to a disc break, with the subsequent flight of particles in an unpredictable direction.

Why can’t a beginner do this? Naturally, following the law of meanness, this direction can be directly your face, or other parts of the body. The speed generated by the rotation of the disc of the angle grinder can accelerate the flying shard.

Let’s take a look at the most common and fraught beginner mistakes:

  • Using an angle grinder without a casing, removal allows you to better control the direction of the cut, but completely removes all the insurance against disc breakage or flying chips;
  • Using a non-standard disc for an angle grinder, most often beginners try to use a heavy circular one, which is also dangerous and can lead to irreversible consequences;
  • Gripping a tool in the wrong place can cause the angle grinder to slip out of your hands.

Shocking photos on the Internet and equally creepy eyewitness accounts on the forums confirm the dangers of using an angle grinder to cut wood. These are people whom non-compliance with TB has led to amputations, severe trauma and even death.

The following information contains comprehensive tips to avoid accidents like those inexperienced guys.

I also recommend reading my books on woodworking to know all the intricacies of the work. details about the book in the “Books” section of the top menu of the site.

It is for the angle grinder that there is a special disc for wood, designed for sawing wood at high speed. Such a circle is not so common on sale.

Do not remove the protective cover! He is the only obstacle between your skin and a spinning circle at high speed.

Large angle grinders will not cut well. Due to sawing hard wood, they can break out of the hands, since at the speed of an angle grinder, the tooth of the wheel clinging to tightly pressed wood fibers is unlikely.

Gloves for work are a must. The best way to get hold of the saw is a fixture. This will turn the angle grinder into a full-fledged machine, protecting you completely from being pulled out, in the case of high-quality installation of the structure.

Do not use cut-off wheels with large teeth, with them the likelihood of clinging the angle grinder, especially to the wood, becomes even lower. The possibility of pulling out grows exponentially.

With an adjustable number of revolutions on the device, set the minimum value. Unfortunately, most angle grinders are simply not equipped with this capability.

The tool should be placed at a right angle, you can cut the workpiece, relative to the plane being cut. Any misalignment can be dangerous. Tilting the device is also highly discouraged.

If there is a button lock, do not use it. In a critical situation, you will not be able to turn off the device in an attempt to minimize damage.

Despite all the tips and rules, the process of sawing wood with an angle grinder can be so random that observing all the precautions given will not be able to guarantee the safety of the master. This is because the angle grinder is not the target tool for such tasks.

Therefore, if you have any alternative opportunity to abandon the use of this tool in favor of a stationary machine, immediately make a decision to use it, even if its transportation will take a lot of time and effort. In any case, health, as well as your own life, is more valuable.

The advice of many experts is a categorical rejection of this tool for this purpose. If there is a large amount of work to be done, then the choice should fall on a jigsaw, which will never be superfluous on the farm.

Devices required for stripping

When using the attachments already described, remember that the angle grinder wheel can leave irregularities that are not visible after processing, but can appear after applying paint. To avoid this effect, use a vibrating machine to level out the effect of unevenness due to the circle.

Grinding operation is the simplest and safest operation that an angle grinder can perform. In any case, follow the safety rules.

Safe cutting wood angle grinder (angle grinder). But can an angle grinder cut wood? You can cut wood with a chain disc with an angle grinder with. And not just wood. Bosch Carbide Multi Wheel

Saw blade for wood for angle grinder (angle grinder). But can an angle grinder cut wood? Saw wood like an angle grinder if you need a bevel cut. Bosch Carbide Multi Wheel. How to properly saw an angle grinder produced by a disc, additionally sanding wood. Two 608 six hundred twenty three 013. Small test.

This, by setting the number of revolutions of the output shaft of the angle grinder, corresponding to that indicated on the marking of the saw blade, they significantly reduce the risk of injury during operation, but do not eliminate it completely. This is mainly due to the material itself, or rather, its structure is not heterogeneity.

Even in different places in the textbook of the trunk, the tree has different hardness, we are not talking about the inclusions of viscous resin, the possible presence of metal trapped in the thickness of the wood: from pellets not bullets that fell into the tree during the time of hunting, to the wire ingrown there, which requires tied up the branches. Remember not about knots, which are present in almost all types of wood.

Having met with the listed obstacles, the saw blade is sharply decelerated not the angle grinder automatically simply pulls it out of the hands, but when passing through a hard area, it rushes forward like oil with a vengeance.

Having met with the metal, there is a high probability of chipping of the carbide tooth, which you like best is captured next, not with the movement of the bullet, is thrown out. It is good if in the coverage area of ​​the protective casing.

A person who decides to cut a tree is even more in danger, because here the angle grinder needs to be put on its side, from what factors the usual uncomfortable grip changes, which means that the grip weakens.

We strongly advise against sawing wood with an angle grinder that does not have speed control with circular saw blades. However, there are now special discs for the angle grinder designed for working with wood.

Difficulties when working with Angle Grinder

We mentioned the inconsistency of the revolutions of the angle grinder of a non-circular saw, alas, users who have an angle grinder with adjustable revolutions will say that this common rumor factor has been taken into account, and any saw blade for wood is also suitable for their tool.

Angle grinder discs for cutting wood

How to cut wood like an angle grinder, how to cut wood into planks with a chainsaw. How to properly saw wood with an angle grinder so that there is no damage and injury, which saw blades are better to use and how to make them. Chain discs and cutters based on them.

In order to enhance the picture. click on its surface.

Many argue that it is possible and that they themselves did this, and some categorically prohibit doing it. Let’s get into the essence, or at least try to get it in order to put a fat point on this issue.

Let’s start without intrigue: our answer for everyone and everyone who reads this article is no, in no case! angle grinder to cut wood, boards, timber is categorically impossible. Rather, it is possible, but the consequences can be sad and very. Look for a picture on the Internet, how terrible the consequences are, and we will explain the theory:

  • During the cut, the angle grinder, if the disc is on the wood, the teeth can grab more wood and then you will have to catch the tool either a few meters away or on yourself. It depends on how the disc stands and in which direction it rotates. Let’s not forget that after the finger stops pressing on the switch, the disc continues to rotate for some time. And here there is already a chance and luck. during such a jerk, the instrument will fall on the hand, finger, leg, chest, stomach, or it will break out of the hands to the side.
  • During cutting, the disc heats up and becomes more fragile. Even a slight bias. and the disc can fly to pieces. And again luck or good luck. you will “catch” such a piece with your eye or your finger, or maybe you will snatch it in the forehead. The chances, of course, are equal. perhaps such a piece of sharp iron will fly off to the side.
  • A disc with victorious soldering can bring a surprise in the form of the very soldering under the skin. We witnessed how a small piece flew under the skin of the thigh and in order to get it, we had to cut the skin a little with a knife. It’s just that the person did not want to go to the hospital for personal reasons, but this is his right. It was science to him anyway.
Read more:  We disassemble the gearbox angle grinder Bosch 125

So, dear ones, remember and pass on further along the line: you can’t cut wood with an angle grinder and no “Is it possible?” But if you really want to, then write a will, kiss the children, make sure that you are quickly found and, after praying, proceed. But we warned.

And just think: why did they come up with a chainsaw and a circular saw, a jigsaw and a band saw?

Greetings, my dear readers of Andrey Noak’s blog. Many people ask on the forums the question, is it possible to saw boards with an angle grinder? Therefore, I decided to fully understand this issue together with you.

The angle grinder is a versatile tool. The angle grinder is suitable for a whole range of jobs, replacing a range of metal tools, often doing the job even better and more precisely. This can boast of all processes produced by a disc for metal. But what about wood and chipboard? Is it safe? Today I want to figure out how to do it correctly at my own peril and risk.

Can I cut wood with an angle grinder

Application of angle grinder for cutting various materials, cutting not sanding wood

If you are trying to understand how an angle grinder can cut wood, then the answer to the myth question is unambiguous: there is an option. How to properly cut an angle grinder wood firewood sawing an angle grinder showed a little how. But probably they will not do this, tk. people get too many injuries precisely from using an angle grinder as a saw for wood, which is correctly called an angle grinder.

Initially, this is caused by the unlimited speed of its rotation, for which most saw blades are simply not designed. Who pays attention to this matter, when it is necessary to do the work, not at hand, of course, an essentially suitable tool, but, in addition, a compensator ring of the required size is applied to the saw blade for wood. Can an angle grinder cut wood, how to do it. In addition, the non-protective casing is removed for convenience of work, which is absolutely impossible to do.

However, we will not talk about injuries here, but let’s talk about how not to process (including sawing) a tree using an angle grinder, alas, before. about the complexities of working with an angle grinder with wood.

Grinding: attachments and process

Sanding pads are discs that are produced by layering several different coatings. To improve the abrasion characteristics of the treated surface, the initial layer is made of rubber, sometimes it is replaced with hard plastic. The layer of the second level of the nozzle allows to ensure the adherence of the plane of the working part to the surface to be grinded; it is made of foam rubber. The main, working layer is a sheet of sandpaper.

Cutting wood with an Makita angle grinder and saw blade

The use of sanding pads allows you to work efficiently with already painted surfaces. Rough polishing of the untreated surface is also possible.

Flap-type discs are suitable for the same purposes, only in rough grinding it turns out faster. A disc of this type is sandpaper petals attached to the working surface of the disc.

To remove paint, it is best to take special devices with peeling functions. Steel cup, with fastened steel fibers made of hard wire, excellent abrasion, additionally sanding wood.

Milling with an angle grinder

Another operation that many experienced craftsmen successfully perform with this tool is milling. Unlike a router, you will not be able to perform really high-quality processing. However, making a groove, as well as cutting a small part. it will turn out to be quite tolerable.

Again, this operation is dangerous. I have already written recommendations for general action using this tool, so follow them. an angle grinder needs a thick and high quality cutter. Immediately dismiss the possibility of using homemade nozzles, give your choice to an old brand, insured against chips and breaks.

Even with all the tips, a beginner alone should not start milling without the supervision of a more experienced craftsman. As mentioned above, accidents constantly occur with the masters of their craft, given the instability of the tool.

Sawing firewood angle grinder

From the administration:
The post was posted in the user’s personal journal.
His experience is not an advertisement for a method of work or a call to follow suit.
This is just a story about how and with what he worked.
The administration encourages readers to use the tools only for their intended purpose and according to the instructions!

From the author of the post:
Rich reaction of readers =)
Well done, that you react to this approach to work, in such a tone. Each instrument has its own place. In this case, I completely agree with you. Thanks to my luck. Sawing wood with an angle grinder did not lead to a sad outcome.
And the answer for the most critical =) You made this post)

Post itself:
Hello dear friends. At our summer cottage, a grandiose construction is underway, which you could read about from my previous entries. You need a building site to build, right? Very often in our life, the environment is littered and it is necessary to carry out general cleaning of the entire territory. Such a time has come at our summer cottage. For more than 20 years, we have been collecting wood material after cutting down obsolete or dry trees. Gathered a huge amount! This can be seen in the images below:

In the summer of this year, we purchased a Makita angle grinder.

This is a versatile tool and with it you can cut anything you want, selecting the necessary discs. To cut wood beams, a serrated disc is required. You can see the appearance of such a disk in the photo above.

I want to focus on the technique of sawing wood using an angle grinder. The block must be tightly clamped with a vise so that it does not move, otherwise it can break the disc. It is very fragile and must be handled with care. I sawed for the first time, and I managed not to damage it. But this is all thanks to the advice of my grandfather, who oversaw my work.

Be sure to use plastic glasses. They will protect your eyes and you will feel more confident with them. Also, I would recommend earplugs because loud noise adversely affects the ear membranes. The volume of work was great and I worked for over 5 hours. After that, the whole evening there was an unpleasant noise and headache in my ears.

Having prepared the workplace, I proceeded to action:

I started with small volumes of wood. Small bars are ideal for firing coal.

Gradually, stacks of bars gather under the table. We sort them by size. Something will go for the heating of a bath, something for cooking in the hearth.

I proceed to the larger bars. The diameter of the disc will not allow cutting wood in one stroke. You have to rotate the log around its axis in order to cut the required diameter.

In the video clip you can see how easy it is to saw wood with an angle grinder. But consider! The angle grinder is a very tricky tool. Always be on the alert. If you are tired, leave work the next day. You need strength to dominate this device.

As a result of painstaking work, by the end of the day, I had finished sawing all the bars. A huge area has been freed up, on which we will continue to build the pool:

In conclusion, I would like to wish you cleanliness and order in your environment. Chaos is a generator of depression and discomfort. Try to make time for something as enjoyable as cleaning. May 2014 be the year of cleanliness and order.