How to replace line in any trimmer
Technological progress provides us with a lot of opportunities to get rid of manual labor. This includes, among other things, mowing grass, which required a lot of physical energy when using a conventional scythe. In modern conditions, this process is much easier, because the applied technique minimizes all costs. Devices such as electric and petrol trimmers have firmly taken the place of irreplaceable assistants in gardening. Mowing grass with their help has become more fun than hard and exhausting work.
Structurally, the trimmer consists of an engine, a rod and a working body, which, depending on the vegetation being cut, is either a mowing head or a disc milling cutter. And if everything is more or less clear with the cutter, then sometimes questions arise with the nozzle. As a rule, they appear when the line ends.
How to properly wind the line on the reel? Understanding.
So, first unscrew the nozzle. This should be done by rotating the drum to the right. Here we have a drum with the remnants of an old fishing line in our hands. We open it. Most often, the lid is closed with latches that can be opened with a screwdriver, threading it through the holes and slightly pressing. Or you need to squeeze the latch and turn the cover in the direction of the arrow. In this case, the lid itself must be held, since reels with automatic line feed have a spring that, when straightened, can throw out all the inner parts of the drum. Gently pulling out the reel, remove the scraps of fishing line from it.
Now you need to take 5 meters of new line and fold it in half (to find the middle). In the middle part of the reel there is a notch (in some designs. a hole), for which we need to hook our fishing line. There is also an arrow on the spool showing the direction of winding. An important detail. if the reel has two compartments, then one half of the line should be wound in one direction, and the other in the other. When finishing winding, you need to leave 15-20 cm of line free. There are also two notches on the top ring of the coil, through which these free ends need to be passed. We dealt with the winding itself.
The last step in the line replacement process is to assemble the drum. First you need to install the spring and washers in their place. Then, holding the reel with one hand, with the other you need to thread the ends of the line into the corresponding holes on the sides of the nozzle. After that, install the coil in its place, tightening the line and being careful not to dislodge the spring. When all the internal elements of the nozzle take their places, you can close the drum with a lid. You just need to make some effort to ensure that the latches fall into place. Voila! The mowing head is ready for use!
How to thread the line into the trimmer spool video
The warranty production of the factory trimmer refueling will inevitably require line replacement. Having a very rough idea of how to thread the line into the trimmer reel on their own, beginners are reluctant to take up this business. However, with some skills, mastering this simple science does not present any difficulties, and the similar instruction presented below will make this process as easy as possible.
Method 2. two segments
Two coiled line lengths
fundamentally no different from the method The only difference is two wound pieces of fishing line, instead of one.
The end of each segment is folded
The end of each segment is folded.
Two special fixing sockets
There are two special fixing sockets on the coil (see picture above).
We start winding the line
They hook it with a hook formed earlier on the fishing line, and begin to wind the fishing line.
Winding is carried out in a special order
The winding must be carried out in the following order: first the lower line, i.e. the one that is closer to the fixing holes at the bottom of the coil, and only then the top one, i.e. the one that will overlap the bottom section.
The bottom line is reeling
The tips are cut into the holes in the trimmer spool body. They are pulled up until they click, which means that the line has come out of the latches.
The tips are threaded into the holes in the trimmer spool body
The coil is fastened into the body. The line in the spool has been replaced.
The line in the spool has been replaced
Preparing for replacement
We disassemble the trimmer spool
For clarity, the mowing head (spool) was removed from the lawn mower. To replace the fishing line, you do not need to remove it, everything is done locally. It doesn’t take long.
We disassemble the trimmer spool. it rests on the latches. Remove the cover by pressing on the latches. If you do not have enough effort to do this with your hands, then use a screwdriver.
The spool consists of the following:
- Spring case
- Cover with locking latches
- Button coil
The principle of operation is as follows. By pressing the button, the spool presses on the spring and comes out of the locking grooves in the spool cap. Holding in this state, the reel can be twisted, thereby adjusting the length of the line. When the button is released, the body spring returns the coil to its original fixed state.
Disassembled trimmer spool
On the bottom of the reel there are several holes for different diameters of the lines. They may differ from trimmer manufacturer. In some cases (like here) they are signed, in others they are not.
These holes are needed to fix the line when replacing it. After winding the fishing line on the bobbin, the ends of the latter are inserted into them. This is necessary so that the scaffold does not unwind when the coil is installed in the trimmer body. In other words, it makes it easier to change the line.
Holes for fixing the line
There are models without specifying the diameter of the consumable. Then, in order to find out what the maximum diameter of the scaffold can be used, it is tried on along the holes for removing the fishing line from the trimmer spool body (see figure below).
Fitting on the holes of the line output
The reel has two line sections separated by a baffle. They may not exist. They are needed only to delimit and facilitate the winding of the consumable.
Two sections for fishing line
First, they are determined with the required length of the loess. The latter is wound into one of the sections of the coil so that it does not go beyond its limits. In this case, 3 mm was wound, the length turned out to be about 2 meters. Those. for two sections you need a 4-meter segment. this is for the 1st method. For the second method, you need two segments of 2 meters each.
Determining the required line length
Now you need to figure out which way you need to wind it. To do this, many trimmer manufacturers apply special designations to the spools, such as in the figure below.
Special designation on the reel
If no such designations were found, then you need to pay attention to the spool body. There is necessarily an arrow that indicates the movement of the mowing head. The line is wound in the opposite direction.
Bobbin case designation
Trimmer head with two antennae
Head with two flutes
After removing the spool from the spool body, we determine the number of strands for winding the fishing line (1 or 2). There is no fundamental difference between bobbins with one and two grooves, but if carelessly threading into the twin groove, there will be operational problems. Due to the likelihood of interlacing adjacent lines of the tool, a situation may arise when, after wear of the working antennae, it is impossible to remove new ones.
Regardless of the number of streams, a fishing line with a length of 1.5 to 3 meters is taken for refueling. Winding must be done in the opposite direction to the rotation of the head, since winding in the direction of travel will lead to the fact that the line will not be removed from the reel. After the fishing line is tucked into the trimmer coil, thread the free ends (15-30 cm) into special holes. Next, we assemble the head in the reverse order of disassembly and check the operability. Do not worry if the ends of the two antennae are very different in size, because when you start the trimmer, the knife installed on the protection will cut off the excess.
Single-barbed trimmer spool
Single-barb lawn mowers reel
Many owners and specialists note the ease of use and ease of refueling the bobbin with one mustache. Depending on the manufacturer, the length of the threaded line can vary from 2 to 5 meters. The end of the line is inserted into the head into a special technological groove or hole, and the winding is carried out in the direction opposite to the working rotation of the bobbin. Most reels have arrow marks on the outside of the body that indicate the direction of travel of the trimmer reel.
How To Put Fishing Line On A Spincast Reel Ft. KastKing Cadet Spincasting Reels
After winding, you need to leave a free end of 15-30 cm to increase the centrifugal force, which is decisive when removing the trimmer line in automatic and semi-automatic spools. We pass the left end through the working hole of the coil and assemble the head.
How to wind the line around the trimmer cutter head or lawn mowers
Changing the line in the trimmer: 2 easy ways
Feedback from our readers is very important for us. Leave your rating in the comments with the reasoning for your choice. Your opinion will be useful to other users.
A gasoline or electric trimmer is an indispensable tool in the arsenal of a modern summer resident or owner of his own home.
Thanks to these garden tools, even a large garden plot can be mowed with ease. After purchasing this tool and performing several mows, many people think about how to properly wind the line on the trimmer reel. For an inexperienced user, the first operation to replace it will seem problematic and time-consuming, since the developers often do not fully reflect the instructions for replacing the fishing line in the operating manual.
Coil with two working tendrils
In this type of spool, you should determine the number of grooves for winding the line, lying on the inside of the spool:
- one groove. both antennae are wound together in one groove;
- two grooves. each antenna is wound on an individual groove.
For both cases, a line with a length of 2-3 m is taken.In single-groove reels, the line is pulled into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the rod side. inside the arrow usually indicates the correct direction of winding. If there are fixing grooves, the ends of the fishing line are threaded through them or held with the fingers of the free hand, they are threaded into the through hole of the outer half of the bobbin, the spool is closed and attached to the trimmer bar.
The difference between the line winding in two-groove spools is that initially a 2-5 m long line segment is folded in half (to determine the middle bend), and the bend loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each along its own groove, fixing the antennae and assembling the coil is similar to the above option with one groove.
The first execution of this procedure, perhaps, will seem long and rather laborious, but with time and experience this task will be solved much faster and easier.
The video below will clearly show how to thread the line into the trimmer spool and wind it correctly. this operation is not difficult and with some patience it will certainly be crowned with success:
How do I load the line into the trimmer spool? Video instruction
The warranty production of the factory trimmer refueling will inevitably require line replacement. Having a very rough idea of how to thread the line into the trimmer reel on their own, beginners are reluctant to take up this business. However, with some skills, mastering this simple science does not present any difficulties, and the similar instruction presented below will make this process as easy as possible.
Restring a 2 sided spool on a string trimmer weed eater EASY!!
Coil with one working tendril
The simplest option and uncomplicated sequence of actions:
- The dimensions of the reel and the length of the original factory winding determine the recommended length of the line for winding. 2. 5 m.
- One end of the line is inserted into the fixing technological hole located inside the spool.
- The fishing line is wound on the drum in the opposite direction of the spool rotation on the trimmer product. as a rule, on the inner side of the reel, an arrow indicates in which direction the winding is carried out.
- A small section of the line is left free to lead it out. it is fixed in a specialized groove on the inside of the bobbin, designed to hold the winding when assembling the bobbin into working condition.
- The left end of the line is passed through the hole in the outer part of the reel.
- The bobbin halves are assembled and put on the trimmer bar.
Preliminary preparation
First of all, to wind the fishing line, you need to remove the spool (bobbin, spool) from the trimmer. specific actions will depend on the complexity of the configuration and the type of the product itself:
- small electric trimmers with a working position of the engine and spools at the bottom, as a rule, have side buttons on both sides of the bobbin. When pressed at the same time, the upper part of the spool together with the inner content for winding the line is detached, while the lower part remains on the trimmer. It is advisable to disassemble the bobbin on a flat, smooth place so that the spring included in the structure does not jump out and is not lost;
- electric and gasoline trimmers with a curved bar without the possibility of installing a knife, as a rule, have spools with a special wing: in such designs, hold the spool in a stationary position with one hand, and rotate the locking reel on the bar with the wing nut counterclockwise with the other. After disconnecting the nut, the entire bobbin is removed.
- electric and gasoline trimmers with the ability to install a knife on a straight bar (for example, Stihl trimmers) have a hole under the reel. To keep the rod stationary, a screwdriver or other suitable object is inserted into this hole and, with slow rotation, such a mutual position is achieved when the screwdriver enters the hole and the bobbin is fixed. After that, the coil body is scrolled clockwise (with a left-hand thread) and removed from the trimmer.
For the second and third cases, the coils, depending on the design, are disassembled in different ways. In bobbins with a lamb, a lamb is unscrewed, in coils with latches, the latches are pressed and one part of the coil is released from the other. If the halves of the bobbin are connected by thread, then it is enough to turn them by hand in opposite directions until they are completely unscrewed.
Coil with two working tendrils
In this type of spool, you should determine the number of grooves for winding the line, lying on the inside of the spool:
- one groove. both antennae are wound together in one groove;
- two grooves. each antenna is wound on an individual groove.
For both cases, a line with a length of 2-3 m is taken.In single-groove reels, the line is pulled into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the rod side. inside the arrow usually indicates the correct direction of winding. If there are fixing grooves, the ends of the fishing line are threaded through them or held with the fingers of the free hand, they are threaded into the through hole of the outer half of the bobbin, the spool is closed and attached to the trimmer bar.
The difference between the line winding in two-groove spools is that initially a 2-5 m long line segment is folded in half (to determine the middle bend), and the bend loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each along its own groove, fixing the antennae and assembling the coil is similar to the above option with one groove.
The first execution of this procedure, perhaps, will seem long and rather laborious, but with time and experience this task will be solved much faster and easier.
The video below will clearly show how to thread the line into the trimmer spool and wind it correctly. this operation is not difficult and with some patience it will certainly be crowned with success:
We carry out the winding of the fishing line
Slowly completed disassembly of the spool-spool without losing its spare parts allows you to proceed to the main task. winding the fishing line into the reel. Technological features of the spool design and the number of working antennae determine the sequence of actions.
Automatic line winding on a spool
There is a type of reel in which the automatic mechanism winds on its own. from the user it is enough only to correctly fill the line. The fishing line is passed through a hole on the inner part of the body, its antennae without winding are passed through the hole on the outer body, the reel is assembled, and when the winding button is rotated, the fishing line inside is wound independently. In such a spool, it is impossible to make the winding wrong: the mechanism itself will determine the correct direction, since it can only turn in one direction.
How the trimmer works?
The principle of operation of such a device is that the grass is cut by a special fishing line installed on a fast-rotating head. The number of revolutions per minute can reach 8000. For a short time, the line becomes unusable, more precisely, it is erased. Then summer residents have a question: “How to thread the line into the trimmer spool”?
How to thread the line into the trimmer spool and which one is better to use for this?
Very often, those people who personally own dachas and vegetable gardens are faced with the need to care for the lawn on the site. In such cases, you simply cannot do without the usual manual braid or trimmer. The first is slowly fading into the background, and the number of people who use it is getting smaller and smaller. The trimmer works automatically and does not require a lot of effort. over, you do not need to have a special skill to use it.
Types of trimmer lines
First of all, in order not to resort to frequent replacements, it is better to use a denser line. The number of its types and manufacturing firms is simply amazing. The main parameter of the trimmer line is its diameter. It varies from 1.6 to 3.2 mm. The most common type is 2mm line. However, its selection must be made depending on the type of trimmer you have.
There are several options for the section of the line. So, it can be round, square, in the form of an asterisk with sharp edges. The last option is the most effective. However, it should only be used on powerful braids and at the same time you need to know how to thread the line into the trimmer spool. Therefore, we can conclude that the more powerful your lawn mower, the thicker the line should be.
A process such as winding a fishing line on a trimmer is not difficult, but it has its own characteristics. First, you need to choose the right fishing line, the diameter of which is prescribed in the device’s passport.
First, unscrew the spool cap. Be careful, as the thread can be left or right. The left-hand thread is necessary so that the head of the scythe does not unwind during operation.
Threading the line into the trimmer
Before threading the line into the trimmer spool, measure 5 m from the skein (this is the average amount of line installed on trimmers). Then fold it in half to find the middle. The resulting center must be inserted into a special slot located on the spool. After that, wind the line in the direction of the arrow on the head.
From the above it follows that the process of replacing the fishing line itself is not difficult. Having carried out such a manipulation as winding a fishing line on a trimmer reel several times, you will bring this process to automatism. The only thing is that you need to constantly monitor the condition of the fishing line in order to avoid breaking it at the time of work on the site, when there may not be a spare coil at hand.
Now you know how to thread the line into the trimmer spool, and you can do it yourself without much effort.!
How to reel fishing line
Fishing is really exciting and exciting business. Beginner spinning players, of course, want to quickly join it and finally get a sensible result. The reservoir where you are going to fish has been selected, all the necessary accessories have been bought. There are rods, reels with lures and lines. too. However. even a slight, but still tangible nuisance can wait right on the shore, which sometimes completely disrupts the whole fishing.
Her name is the winding of a fishing line on a reel. Each coil seems to be equipped with an instruction with a basic diagram. But the fact is that with such an attitude, it will not be possible to catch a lot for sure. If the loop is wound incorrectly, the loop may be thrown off, and instead of removing the fish from the hook, then you will have to bother with untangling a lump from the fishing line with your own hands.
They start using spinning most often with tackles that are shorter (both reels and rods). The caliber of the bobbin in them is two to three thousand (that is, a hundred-meter line is not more than a third of a millimeter thick in this case, the limit). The winding structures can also be very different: this is a chaotic winding in a chaotic arrangement of Chinese samples (more or less suitable for monofilament, but completely inappropriate with a braided line), and such more professional formats as a straight cylinder, straight and inverted cone. And from the very beginning it is better to get used to those types of styling that are more serious, because this is not a whim, but a higher efficiency. Having saved a few hundred rubles in passing, you will then begin to curse everything in the world, when, instead of casting and biting (well, or just casting and waiting), fishing turns into a continuous struggle with “beards” and other overlaps of the line. Such a catch has never brought joy to anyone.
How to quickly wind a line on a spinning reel
The basic, fundamental rule is that the equipped line must be flat, like a ruler. For cylindrical winding, a straight line is optimal, and if a cone is chosen, then an inclined one. But in any case, remember firmly, only the line without bends.
How can this leveling be ensured in practice? First of all, we attach the bobbin to a fixedly placed rod-shaped object, on which it should scroll easily and freely. Pencils and knitting needles, fountain pens and screwdrivers, small metal tubes without sharp edges, and even a smooth and well-polished stick can act as a rod. As a last resort, find someone who agrees to hold.
Pull the line through every single rod ring. Tie a knot at the extended end. Now you can start threading the line to the surface of the reel. First, we fasten it on top of the bobbin in a circle, having previously lifted up the arc of the line stacker, and when another knot of the “Arbor” type is tied and tightened, the arc can be lowered.
Braided line loves to slip very much. This can be avoided by prying a piece of rubber under the attachment point (for example, cut from an unusable fingertip or worn-out glove), in extreme cases. support it with adhesive plaster, if there is no rubber.
And now comes the turn of the line winding. Turn the handle on the reel neatly and evenly. Make sure the line is tight all the time. It is imperative to support it, but only in tight gloves.
When winding up, avoid, as much as possible, ending it at the level of the bobbin collars. If you do not follow this rule, then self-resetting of loops or their eerie entanglement becomes very likely. To avoid such an outcome, pay attention that at least a millimeter or two of the fishing line remain unwound up to the side. On the other hand, exceeding the gap of five millimeters can make long-range casting impossible. Backing is a preventive measure (in fact, winding up the bottom of the main line of the auxiliary line, no thicker than three tenths of a millimeter, otherwise an even laying will become unattainable). Please note that almost all threads work well in backing, except for long-drying cotton and nylon.
See useful how to properly wind the line to the reel
It is possible to determine how much fishing line to throw on backing, it is possible only by experiments, there are no ready-made formulas and theoretical provisions on this score. Another bobbin is required. We wind the main forest on it, then backing (do not forget about the gap from the side). Next, we attach the main mount, to which we are already introducing the fishing lines in the reverse order. Visit our website and read more useful tips for fishermen.
Preliminary preparation
First of all, to wind the fishing line, you need to remove the spool (bobbin, spool) from the trimmer. specific actions will depend on the complexity of the configuration and the type of the product itself:
- small electric trimmers with a working position of the engine and spools at the bottom, as a rule, have side buttons on both sides of the bobbin. When pressed at the same time, the upper part of the spool together with the inner content for winding the line is detached, while the lower part remains on the trimmer. It is advisable to disassemble the bobbin on a flat, smooth place so that the spring included in the structure does not jump out and is not lost;
- electric and gasoline trimmers with a curved bar without the possibility of installing a knife, as a rule, have spools with a special wing: in such designs, hold the spool in a stationary position with one hand, and rotate the locking reel on the bar with the wing nut counterclockwise with the other. After disconnecting the nut, the entire bobbin is removed.
- electric and gasoline trimmers with the ability to install a knife on a straight bar (for example, Stihl trimmers) have a hole under the reel. To keep the rod stationary, a screwdriver or other suitable object is inserted into this hole and, with slow rotation, such a mutual position is achieved when the screwdriver enters the hole and the bobbin is fixed. After that, the coil body is scrolled clockwise (with a left-hand thread) and removed from the trimmer.
For the second and third cases, the coils, depending on the design, are disassembled in different ways. In bobbins with a lamb, a lamb is unscrewed, in coils with latches, the latches are pressed and one part of the coil is released from the other. If the halves of the bobbin are connected by thread, then it is enough to turn them by hand in opposite directions until they are completely unscrewed.
Want to see? Rating of the best lawn mowers!
How to wind the line onto the trimmer spool
Unplug the trimmer before changing the line (switch off the engine for lawn mowers). The procedure is as follows:
- On a curved bar trimmer, unscrew the thumbscrew and remove the mowing head.
- On a straight bar trimmer. insert a screwdriver or hex key into the hole under the spool. Lock the key and unscrew the coil.
There is a type of reel in which the automatic mechanism winds on its own. from the user it is enough only to correctly fill the line. The fishing line is passed through a hole on the inner part of the body, its antennae without winding are passed through the hole on the outer body, the reel is assembled, and when the winding button is rotated, the fishing line inside is wound independently. In such a spool, it is impossible to make the winding wrong: the mechanism itself will determine the correct direction, since it can only turn in one direction.
How to wind the line correctly on the trimmer spool? Video review
We carry out the winding of the fishing line
Slowly completed disassembly of the spool-spool without losing its spare parts allows you to proceed to the main task. winding the fishing line into the reel. Technological features of the spool design and the number of working antennae determine the sequence of actions.
The simplest option and uncomplicated sequence of actions:
- The dimensions of the reel and the length of the original factory winding determine the recommended length of the line for winding. 2. 5 m.
- One end of the line is inserted into the fixing technological hole located inside the spool.
- The fishing line is wound on the drum in the opposite direction of the spool rotation on the trimmer product. as a rule, on the inner side of the reel, an arrow indicates in which direction the winding is carried out.
- A small section of the line is left free to lead it out. it is fixed in a specialized groove on the inside of the bobbin, designed to hold the winding when assembling the bobbin into working condition.
- The left end of the line is passed through the hole in the outer part of the reel.
- The bobbin halves are assembled and put on the trimmer bar.
In this type of spool, you should determine the number of grooves for winding the line, lying on the inside of the spool:
- one groove. both antennae are wound together in one groove;
- two grooves. each antenna is wound on an individual groove.
For both cases, a line with a length of 2-3 m is taken.In single-groove reels, the line is pulled into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the rod side. inside the arrow usually indicates the correct direction of winding.
The difference between the line winding in two-groove spools is that initially a 2-5 m long line segment is folded in half (to determine the middle bend), and the bend loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each along its own groove, fixing the antennae and assembling the coil is similar to the above option with one groove.
The first execution of this procedure, perhaps, will seem long and rather laborious, but with time and experience this task will be solved much faster and easier.
How to wind the line onto the trimmer spool
How to choose a fishing line. length, diameter, restrictions
IMPORTANT TO REMEMBER! Do not use fishing line or metal cables for the trimmer. This replacement is ineffective and dangerous. The rope can injure not only the mower himself, but also those around him.
As for the length, you should rely on the estimated frequency of use of the trimmer. The more often, the more it costs to stock up expenses.
Information about the possible line diameter can be found on the body trimmer spools. Most likely, the range will be indicated there. The thickness varies from 1.2 to 4 mm. Choose the appropriate option, taking into account the characteristics of the cultivated area. The larger the diameter, the easier it is to mow tough grass.
Winding Algorithm
Insert the resulting loop into the groove.
Lay the line in the direction indicated on the element body.
Insert the short end into the slot on the side of the spool.
Secure the long end in the opposite groove.
Place the spool of coiled line into the spool body.
Pull the line out of the locking grooves.
Put on the cover and fix.
Trim the ends of the line, leaving 10 to 15 centimeters.
The replacement of the line is completed and now all that remains is to screw the bobbin onto the trimmer and you can work.
Preparation. remove and disassemble the spool
On most electric and petrol trims, you will need to remove the spool to replace the line. The FUBAG tool lets you skip this step. To make the instruction universal, we will still consider it in detail:
Secure the shaft. Insert the locking element into the corresponding hole. It can be a thin screwdriver or a metal rod.
Unscrew the bobbin case. In our example. strictly clockwise.
Unscrew the cover according to the direction indicated on the body.
Remove the coil for winding.
The preparatory stage has been passed. You can proceed to winding the fishing line.
How to properly wind the line on the trimmer reel. Step-by-step guide VIDEO
ATTENTION! Typical line problems
No wonder they say: “Forewarned is forearmed“. Knowing about possible problems and the causes of their occurrence, you can prevent them in time. We recommend to remember or leave a memo.
| Problem | Cause | Decision |
| Line break | Stones, branches and solid objects in the grass | Avoid collision |
| Poor cord quality | Replace with a quality analogue | |
| Head outlet wear | Complete replacement of part required | |
| The line is unwound | The spring in the coil is weakened | Check spring and replace if damaged |
| The line is sticking | Poor line quality, due to which it can melt under the influence of temperature from the heating head | Reel in less line or replace with a better line |
For a better understanding of the mechanism of the process of changing the line in the spool with a video guide prepared by FUBAG specialists: