How To Start A Husqvarna Gasoline Lawn Mower

older above
new higher
by rating

lady v

If you look at how the electric trimmer is arranged, then note that its engine, all parts of the device that are energized, are at a height on the part of the mower opposite the mowing head. Relatively speaking, the engine of the electric trimmer does not fall below the chest of the person working with it.

So there is no danger for a person who decides to mow wet grass with such a trimmer. I admit that I had to mow the wet grass with an electric trimmer on the lawn behind the house and nothing bad happened.

Here in the rain, of course, mowing with an electric trimmer should not be, but honestly, it’s hard for me to imagine such a gambling mowing that would mow the grass right in the pouring rain.

The only thing is if you have some kind of wire connection, extension cord. It is better not to put it in wet grass.

By the way, the usual scythe was always mowed in the mornings, along the dew, that is, it was wet grass. It is probably easier to mow.

With an electric lawnmower it’s more complicated, it has an engine below, so it’s better to wait here for a while, let the grass dry. Also, if you have a trimmer model with a lower engine position, they also should not mow wet grass.

How To Start A Husqvarna Gasoline Lawn Mower

Hello! Honestly, I am very far from mowing grass. But two mutually exclusive words in your question caught my attention. These are the words “wet” and “electric”.

From school knowledge of physics, it was remembered that water is a conductor of electric current.

Therefore, it will be logical to assume that mowing wet grass with an electric mower that is powered by electric current is very dangerous.

I don’t know what the experts on this matter will say, but personally, with the mower turned on, I’m even close to wet things and, especially, to wet grass, I will not come up solely for safety reasons. In my opinion, a technical amateur, the words “wet” and “electric” are a priori incompatible.

and an electric washing machine is a terrifying thing for you, not to mention an electric kettle! )))
– 1 week ago

Each owner of a country house or a gardener who has planted a lawn for the first time on his plot faces the question: when do you need to mow a lawn for the first time and how to do it right? The first haircut of young seedlings should be done no earlier than 25-30 days after planting. Sometimes the haircut is postponed due to the fact that fresh shoots of grass look weak and are afraid to trample them. This is mistake. The fact is that from being trampled, the lawn grass begins to grow stronger, forming a dense sod.

Regular grass mowing

Mowing an adult lawn is usually done once or twice a week, depending on the intensity of grass growth under various weather conditions. Regular and proper mowing strengthens the grass, makes it more magnificent and does not allow weeds to flourish. There are norms that establish the height of the stand based on their biological characteristics. The mowing height of thin-leaved grass of the lawn is not lower than 3 cm, for broad-leaved 5 cm.

The most common lawn mowing tools: lawn mower, trimmer, cordless grass shears.

You need to mow in dry cloudy weather. The rule "mow braid while dew" with modern lawn mowers can play a bad joke. The fact is that the wet grass sticks together, sticks to the plastic, which leads to blockage and does not allow the grass to freely get into the grass catcher. However, mowing the grass in the scorching sun also negatively affects the green coating, the grass turns yellow, the tips dry out. In sunny weather, the best time to mow the lawn is evening. With prolonged drought, do not mow the lawn too short, try to maintain a grass stand of about 5 cm. This mowing height will protect the soil from drought, and the lawn will look well-groomed.

Proper mowing

Some useful tips on how to mow grass:

  • Make sure the same height is set on all sides of the mower;
  • Remove any excess from the lawn before mowing. It can be branches, apples, fallen from trees and other objects;
  • If it was raining the day before, or the grass died from strong dew, comb it and let it dry;
  • Fans of striped lawns should know that the stripes appear when changing the direction of mowing, or from changing the speed of mowing, when it comes to a mower of a cylindrical type;
  • For uniform mowing, you need to move in a spiral, starting with a large radius. First, mow the perimeter, then the spiral begins to converge to the center;
  • Never run a mower over a wire;
  • After hearing the strange sound of the mower, stop operation immediately and make sure that no solid objects get into the mower;
  • If the grass remains on the lawn and does not fall into the grass catcher during mowing with a rotary mower. This can happen for two reasons: wet grass gets lumpy and clogs access to the grass collection box or the grass collection box is full;
  • Mounds and bumps inevitably arise on each lawn. In order not to leave bald spots on them after cutting, you can just slightly raise the mower by the handle;
  • The ragged edges of the grass stand are a reminder that it is time to sharpen the mower’s knives;
  • The appearance of the lawn will be better if you alternate the direction of mowing. For example, today mowed the lawn clockwise, and the next time counterclockwise.

It is not possible to mow the lawn evenly with a regular grass scythe, therefore the lawn mower is the main tool for even mowing. Lawn mowers are different: self-propelled, with steering, with a handle for control. The principle of operation of lawn mowers is also different: cylindrical, rotary, riders, robotic mowers, hovercraft mowers, manual lawn mowers (trimmers). Not only the principles of operation are different, but also the ways of powering the devices: electricity, batteries, gasoline.

Why mow grass

Weed grass has good adaptability to any growing conditions and grows everywhere. If weeds are not destroyed, then in a couple of years they will turn any site into a wild field. Weeds propagate not only by seeds, but also by rhizome. Thus, to remove some types of vegetation will have to spend a lot of time.

One of the most important items to care for your garden or garden is weed removal. Learn more about the most common weeds, as well as how to deal with them folk remedies, special tools and herbicides.

Growing weeds quickly develop the useful area of ​​the site, intensively use nutrients and moisture from the soil. It is impossible to destroy the unsolicited flora, which grows next to useful plants, by chemical means.

This will lead to the death of all vegetation. For these reasons, grass mowing is a must. For the rational use of their time, it is necessary to choose the right tool for mowing:

  • mowing with a lawn mower is necessary on an even large area. a lawn or rest area;
  • it is convenient to work with a trimmer in any areas if the height of the grass is 5 to 10 cm.
  • oblique mow tall grass or vegetation in an uneven area.

When choosing a tool, you must remember that the older the braid, the better the metal used to make it. Modern braids significantly lose in the quality of the Soviet. The size of the tool is indicated by a number from 3 to 9. The number determines the length of the blade: the larger the number, the longer the braid.

Important! It is forbidden to work with braids and other cutting tools barefoot or in open shoes. Before work, it is necessary to check the reliability of the fastenings of the cutting parts.

How to mow grass: technique

Good mowing is ensured by a well-chosen working tool and its preparation for work.

Did you know? The name of the inventor of the braid is not preserved in history. But you can understand that the tool appeared at a time when iron was expensive. This is evidenced by the technology of riveting braids. with it there is minimal metal wear.

Instructions for preparing for mowing:

  • The tool must be sharp and not dull while you mow. Sharpen it on an abrasive wheel. The width of the circle is 1.5-2 cm, the blade is wetted during sharpening so that it is wet. Sharpened the bottom.
  • Blasting is performed using a special hammer. The purpose of beating is to prevent the blade from blunting quickly when mowing.
  • Both planes of the braid sharpen bar. If you have no experience sharpening such a tool, then it is advisable to find a professional.

Read more about how to use and care for a hand scythe.

  • mowing starting position: take tool; in work, the body will bend slightly, following the movement of the hands; supporting leg is slightly in front; the body is slightly turned to the left.
  • the mowing wave will consist of two parts: first the tool goes in one direction, then in the other.
  • the swings are not wide; hands move like pendulums. from right to left and then a second swing from right to left.
  • smooth waves. there should be no tension in your hands, otherwise you will quickly get tired.
  • to make it easy to mow, the handle should be located at the level of the belt.
  • when the mowers mow, the heel of the braid rakes the mowed plants and folds them to the side of the mowing. It turns out a grass roll.

The mowing should be straight, its width should not change. Video: how to mow grass with a manual scythe

Did you know? The ancestor of the braid is a sickle. His images can be found in all civilizations of the ancient world. This agricultural tool was widely used in the XVII-XVIII centuries.

Network user reviews

I do not agree. it’s very difficult to mow, it’s hard and long (for me). I could not get used to it. Kosh herself only by hand, for a long time mowed poorly beaten and stupid scythe. Nevertheless, a trailer of 750 kg with an impressive mountain I cough up for 20-30 minutes with smoke breaks. Depends on the grass and mood. Laying time is not considered. Koshu only in the afternoon, at another time does not work. Kosh where you have to. that’s why the grass is different. By the way, two-way koshu, roll, it seems called. I do with ease. Only the third year I mow itself and constantly. the whole grass season. The husband generally mowed the trailer in 10 minutes. I was just thrilled &# 128518; But man mows his whole life. Yes, and normally did the scythe, so much to compare with me. But, these are two extremes, so I started a topic to find out, so to speak, average indicators. strength is needed, how much dexterity. IMHO. How many times I observed in the village. the old grandfather mowed better than the young and strong. I never learned to mow with a manual scythe, apparently I don’t have enough patience, but a lawn mow is very much. Again, plus, manual only dew is good, and benzo at any time. For 1.5 hours with a lawn mowing I will lay and lay a full car trailer (750 kg). Usually mowing together, then one mows, one collects and leaves for less than an hour. With a lawn mowing it is easier to stack 2 rows in one swath, then assemble 2 times faster. Now lawn mowers are not expensive, even with 1-2 horses it will pay off in 2 seasons, that’s for sure, and saving your strength is also worth something.

Lawn mower

Before starting a gas mower, a visual inspection should be made for visible damage. The process of starting the unit is conditionally divided into several stages.

Fuel mixture preparation, refueling

If the mower is started after winter, the contents of the tank are checked: if there is unused fuel, it should be drained. Then you can start refueling equipment. It is important to know some nuances here.

To fuel two-stroke engines, it is necessary to use a fuel mixture. It can be purchased ready-made or prepared yourself. There is nothing complicated in the preparation of the mixture, but you need to adhere to the necessary proportions.

Lawn mower gasoline Oleo-Mac

When using synthetic oils, a proportion of 1:50 is used. for 5 liters of gasoline 100 g of oil.

When using mineral oils, the proportion is 1:35. 100 g. Of oil per 3.5 liters of gasoline.

Refueling a four-stroke engine does not require preparation of the fuel mixture. A special oil sump is provided here, gasoline is poured separately. It is important to remember that the oil also needs to be replaced, depending on the intensity of use of the mower. Basically, you need to change the oil every 50 hours or at least once a year.

Important! Lawn mowers work well when using oils with a viscosity index of SAE-30. In addition, if the engine was run in with synthetic oil, then it cannot be replaced with mineral oil and vice versa.

As for gasoline, Chinese, Japanese and American lawn mowers work well with A-92 fuel, for European models it is better to use gasoline with a large octane rating.

When refueling the mower, make sure that the level of gasoline is 2-3 cm below the edge of the fuel tank.

Starting a cold engine

Before starting an unheated lawnmower, the transmission, ignition system are turned off, and the motor shaft is scrolled by the starter or starter cord.

Then a series of actions is performed:

  • The ignition turns on;
  • The choke closes;
  • The engine is starting up.

Petrol lawn mower STIGA Collector

If the mower does not start, you will have to carry out a number of manipulations:

  • The damper remains closed, the ignition is on;
  • The fuel pump (suction) button is pressed about 5 times;
  • An attempt is made to start the engine.

In case of repeated failure, the following should be done:

  • open the shutter to prevent the filling of candles;
  • scroll the shaft with a starter;
  • blow through the combustion chamber;
  • start the engine.

Sometimes for the first start of the motor about 15 jerks may be needed. this is quite normal for this technique.

When the engine starts, the throttle lever is squeezed once to use idle. Further, the lever is set to a position corresponding to low revs. In this position, the engine should run for about 5 minutes to warm up. If necessary, its operation can be stopped by pressing the “Stop” button.

Attention! It is not recommended to work with an unheated engine. this affects its performance and durability.

Warm engine start

Starting a pre-warmed motor is much simpler and does not require such efforts:

  • the control knob is set to the "maximum fuel supply" position;
  • engine starts;
  • the desired speed is selected.

You can get to work.

Startup Errors

The most common errors when starting a gas mower are:

  • Inadequate or complete lack of gasoline. A commonplace, but fairly common reason why a lawn mower does not start. The tank is checked, gasoline is added to the desired volume.
  • Poor fuel or improperly prepared fuel mixture. In this case, it is very important to study the recommendations and instructions on the issue of the required fuel quality, regarding the model of the mower used.
  • Incorrect air damper position. If the shutter is closed and the number of jerks is more than 5, there is a risk that the fuel will flood the candles.
  • Ignition off during startup. Ignition should be switched on immediately after closing the air damper.

Video: How To Start A Husqvarna Gasoline Lawn Mower


Lawn mower gasoline Intertool LM-4545

The main breakdown of lawn mowers

Despite the large selection of manufacturers and the variety of models, the reasons why the Makita, Honda, Husqvarna or other lawn mowers do not start are the same for everyone.

The main reasons why a gas mower does not start or starts, but immediately stalls, there may be problems with the ignition, carburetor, filters.

If the filled fuel and fuel mixture are of good quality and in the right quantity, the air damper is closed, the mower starts up and stalls immediately, the cause may lie in the following malfunctions:

  • Defective or filled spark plug. In this case, you should unscrew the candle, dry well and thoroughly clean it with a nail file or file. Excess fuel is drained, the candle hole is dried. A clearance of 1 mm is set, and the candle is screwed in again.

Important! Drying the channel requires at least half an hour.

  • Dry threaded connection. It should be lubricated with gas so that the spark could flare up.
  • Lack of spark from a candle. In this situation, the contact of the candle and the high-voltage wire is first checked. If the contact is normal, and the lawnmower makes a clap and stalls, there is a problem with the ignition, and you cannot do without a service center.

These breakdowns are common reasons why the Husqvarna Lawn Mower will not start.

Fairly common causes of garden equipment breakdowns, including why the Honda lawnmower does not start, are problems with the air and fuel filters:

  • Clogged air filter. If the first possible reasons are not confirmed, and the mower still stalls, you can remove the air filter and try to start the device without it. If the stalled engine starts, the reason is in it. The filter should be cleaned or replaced with a new one.
  • Dirty fuel filter. Another possible diagnostic option. The filter element is inspected and replaced if necessary.

Important! Running a lawn mower without a filter element is highly discouraged.

  • Breather pollution. With its help, the pressure in the gas tank is regulated. If the breather is blocked, a vacuum is created and the fuel supply stops.

The following breakdowns are more serious and without certain skills, it is not easy to cope with them. There are problems with carburetor malfunctions:

  • Contamination of nozzles and channels. They are washed with special liquids, blown with a stream of air from the carburetor.
  • Worn gasket. It is being replaced with a new gasket.
  • Leakage damage. Diagnostics is carried out using a tonometer. If the pressure is stable, everything is fine, it falls. you need to find and replace the damaged element.

Another failure option is a piston group problem. Worn or damaged pistons should be replaced.

Lawn-mower gasoline Knight of BG-4900

Petrol Lawn Mower Operating Rules

Like any equipment, the mower needs some care features and the basic principles of use. These rules are simple, but will help maintain the health of the unit for a long time.

General operating rules:

  • Read the instructions for use and care of the lawn mower, learn the basic rules of operation, storage and safety.
  • After each use, clean the housing, channels, grass catcher, knives, preferably using special fluids.
  • Do not clean the hot engine mower.
  • During operation, monitor the condition of the engine, prevent it from overheating, take breaks.
  • At large intervals in the operation of the lawn mower (about a month), drain the fuel. At the same time, at the end of work, the device is given the opportunity to idle and stall.

Rules for preparing equipment for winter:

  • A visual inspection of the mower is carried out, the main parts are removed, cleaned, dried, damaged.
  • Fuel drains.
  • The air filter is cleaned.
  • Oil is poured into the gearbox.
  • All moving parts of the engine are cleaned and lubricated.
  • The motor is wrapped in oiled cloth.

Lawn mower petrol MTD Smart 51 BO

  • Before starting work, the work area is checked for foreign objects: stones, branches.
  • Outsiders must not be present at a distance of at least 5 m from the mower.
  • Work is carried out in special glasses.
  • A visual inspection of the lawn mower for damage, loose parts. Malfunctions are eliminated.
  • You can mow grass, not higher than 20 cm, no more than a third part at a time.
  • When working on slopes, you should move along the slope, and not up and down.
  • Before changing the bevel height, the engine stops.
  • If foreign elements get into the knife of the mower, the work stops, the knife is cleaned.

Gas mowers have earned the respect of users for their power and quality. In order to prolong the durability and performance of the unit, you need to study all the intricacies of the care and maintenance of the lawn mower, comply with safety rules, adhere to the operating instructions for this equipment.

Why you can not mow wet grass with a trimmer

What trimmers can mow wet grass

To understand which trimmers you can mow wet grass, and which not, you should deal with their device. Today, the consumer has two main types of lawn mowers:

trimmers, depending on the location of the motor, can be:

  • With the top location of the electric motor;
  • With the bottom location of the electric motor.

Based on safety considerations, mowing grass that is wet from rain or dew can only be done with a gas trimmer or a “lithuania”. The introduction of electronic lawn mowers is very unnecessary. Especially when it comes to devices with a lower motor, because they are in the area of ​​water. As a result, Kutzey Closure may occur.

It is not recommended to mow the grass during the rain and trimmers with the top of the motor. In the case of penetration of water to the unit can not only shorten, but also hit the current with mowing.

Wet grass also cannot be mowed with electric lawn mowers. The reason is the same as with trimmers with a lower arrangement of the unit. the possibility of a short circuit is great. In addition, there is a danger that, by vigilance, you can accidentally cut off the power wire that feeds the unit.

If you still need to mow the grass in wet weather or in dew, then better use carburetor lawn mowers and lawn mowers. It will be even safer for life and health.

Why you should not mow wet grass with a trimmer

There are indirect prerequisites for why it is impossible to mow grass wet from dew or rain on a personal plot. These include:

  • Early trimmer wear;
  • Damage to the lawn.

How can a lawn mow be disabled by mowing moist vegetation? Everything is simple. It is displayed as a result of a short circuit when water enters the power compartment. In addition, even if everything is very well sealed, there is a great possibility that the engine will not withstand the large load created on the flexible shaft of the trimmer. Well, the shaft itself can crank. Such loads in most cases appear from the sticking of wet grass on the knives and on the spindle to which they are attached.

In trimmers with a gasoline engine, mowing grass in wet weather, due to enormous loads, increases the degree of wear of the main components and assemblies. Is it possible to mow grass in mow wet grass with an electric trimmer. Here we can note the early failure of the piston pair, as well as other moving parts. In most cases, the piston pair fails due to overheating of the motor. In our case, the motor will overheat from the load created by wet grass during mowing.

If you mow wet grass with a gas trimmer, to prevent the motor from overheating, let it idle for 30 seconds without load. This method will remove excess heat and keep the piston pair.

About the dangers to lawn grass

Many probably noticed that if you trim the wet grass with a trimmer, the cut comes out torn. In the coming years it dries up, and the grass itself begins to turn yellow. This can happen for several reasons:

  • The wet grass is very elastic and pulls to the ground;
  • The trimmer line is either very thick, or a round line is used.

In the first case, you should wait until the vegetation dries. When drying, the grass always becomes stiffer. In the 2nd case, it is worth changing the line to a narrower one or with a different profile. As practice indicates, a flat section on wet grass can be obtained using profiled woods with a square or star section.

Those who at least once tried to mow the grass in dew or in drizzling rain noticed that the vegetation adhering to the knife and the spindle was scattered in heaps on the lawn. If they are not fit to be removed, then in the places where wet grass falls on the lawn, spills occur. Mowed heaps begin to rot, and the lawn begins to hurt. So there are unsightly bald spots.

So, dear readers, decide for yourself whether it is possible to mow wet grass with a trimmer and a lawn mower, if you still want to clean the lawn before the onset of cold weather.

Preparing the trimmer for work

Preparation of the trimmer for work begins with checking the status of all parts and assemblies according to the annotation. With all this, you need to make sure that there is grease in the gearbox, and that there is enough oil in the crankcase of the four-stroke gasoline trimmer. The fuel, depending on what type of engine, two- or four-stroke, is a mixture of gasoline with special oil in a ratio of 40-50: 1 or, accordingly, stained gasoline. After the fuel tank is full, it remains only to open the faucet and you can try to start the trimmer, without forgetting that before mowing it is necessary that it runs at idle for 2-3 minutes.

With electric battery equipment, everything is simple. after checking for lubrication, it is enough to insert a charged battery into the appropriate socket so that it is ready for use. If the tool is powered by the mains, then an extension cord will be needed to the intended place of cutting. The wire must be located outside the zone of probable action of the trimmer knives.

The site should be very freed from third-party objects: glass, pebbles, wire, snags, etc. The presence of people closer than 15 meters is also not necessary. Depending on the abilities of a particular trimmer and the intended work, it is necessary to choose a suitable cutting nozzle. You can use a mowing head with a fishing line for grass, iron knives for weeds, or harvesting hay or a saw for a bush. Mowing should be planned in such a way as to advance, moving away from buildings and people.

How to mow with a trimmer

The trimmer should perfectly "lie" in the hand. Many people prefer a rather light tool that can be used "on weight". In an unpleasant case, it should be perfectly balanced, on a comfortable belt or a backpack suspension, because it is impossible to mow with a trimmer correctly. The tool is very comfort with a bicycle handle, which allows you to simply hold the mowing head at approximately the same height when mowing, and the tip of the cutting tool at a suitable distance from the ground. In order for the fishing line to serve longer, you do not need to bring it close to fences, borders, brickwork and other solid objects. In addition, it should not be necessary to touch the head of the earth.

How to choose a trimmer for a summer residence? Which is better: gasoline or electronic? Find out here.

Common Weed Trimmer Mechanisms

Usually, the cutting tool rotates counterclockwise, so you can work with the trimmer in the same way as an oblique lithuania, making 1-2 swings from right to left with a gradual advance of 15-30 cm. Then the mowed grass remains on the treated surface on the left. Since the fishing line cuts perfectly with the very tip, the sweep speed and grip are selected empirically. Is it possible to mow grass in the rain, wet grass. With frisky wiring, the cut occurs with the entire length of the cutting tool, in this case the motor is overloaded too much, and the grass is often wound around the head.

Rivnekaya glade

If the platform is large and even, and the grass is quite soft, then it is more convenient to mow along imaginary squares, at the level of thoughts, breaking them into their entire area. For previously mowing the grass around the perimeter of the first, continue to work along the tapering square spiral clockwise until the site is completely mowed. Then proceed to the next square. Mowed grass with this method always remains on the treated surface on the left side. In order to mow vegetation to the very root, you need to keep the cutting plane at an angle of 30 °, with the tip of the fishing line almost touching the ground.

How to mow hard grass with lawn mowing. life hack

We combine the nozzle with knives and the spool with fishing line for mowing the stiff grass of the lawn mowing.

Naturally, even glades are better to be mowed with a lawnmower-cart, which allows you to make a more even cut and collects the cut grass in a special grass catcher. About the choice of such a lawn mower is described in this article.

Highest grass

In this case, it is more convenient to mow in both directions. 1st pass. from left to right, cutting the tops of the grass, and then, lowering the tool to a suitable level, the lower part is cut off by reverse movement. Mowed grass also remains on the treated surface on the left side. If the thickets of weeds are very high, then in order to reduce the possibility of winding grass on the drum, you have to mow a couple of times from top to bottom, but this is fraught with excessive consumption of fishing line.

Slope processing

The slope is also treated according to the principle of “mowed grass to the left”, choosing the direction so that its top is on the right. Having reached the end of the plot, they turn to the starting point, rise higher by the width of the swing and mow the next strip.

Trees and bushes

On a site where there are many similar obstacles, the trimmer is simply irreplaceable, because mowing the grass with an ordinary scythe is not enough scope, and the lawn mower is very large. For this, the fishing line is ideal. Before you begin to process the site, you need to cut each tree or bush from all sides. In order not to destroy them, it is necessary to hold the trimmer with a protective casing practically against them, tilting the head slightly to the ground and going around from left to right.

Pruning

It is comfortable to trim the flower beds, lawns and paths on the sides with a trimmer with a lower engine, because its cutting plane can be set vertically. For even greater effect, it is useful to dig a groove of approximately 4×4 cm along the cutting strip. Then the fishing line will cut the grass, below ground level without touching its surface. The result is a very spotless, flawless vertical haircut.

Wet weather work

If there is a need to mow with a trimmer in any weather, then it certainly must be gasoline, as it tolerates wet weather well. Although, according to the annotation, work in the rain or on wet grass by some manufacturers of similar gasoline equipment is also prohibited. When choosing a trimmer, it is also worth paying attention to.

The electric motor is the most vulnerable place for battery trimmers in water. Accordingly, if it is placed on top, then there is less chance of getting water from the grass, but in rainy weather they can’t work either.

sensitive to moisture trimmers powered by the mains.

Typically, water from wet grass enters the extension cords, where an electronic arc may appear that could ignite the insulating plastic or cause a short circuit. This drawback is “corrected” by buying a new extension cord or replacing the plug, but water entering the engine or control circuit leads to an irreversible trimmer failure. In addition, working with such equipment in the rain is simply unsafe, since there is a great possibility of electric shock.

Storage and care of the trimmer

Particularly painstaking care requires gasoline trimmers. In addition to cleaning and lubricating cutting and rubbing surfaces from plant sap and dirt, you must also take care of the engine. Faster than all, he clogs the air filter. The frequency of cleaning is approximately 10 hours. In addition, from time to time the fins of the radiator of the cooling engine become dirty, which is why it quickly overheats, and this can lead to its jamming. How to clean the radiator and air filter is described in the annotation for a specific gas trimmer.

Before throwing the trimmer for long storage at the end of the season, all fuel should be drained from it, then start the engine and wait for it to stop. This ensures a complete lack of fuel in the tank and carburetor. After the motor cools down, it is necessary to unscrew the spark plug, add 30–40 ml of two-stroke oil to the cylinder, slowly crank the crankshaft with a starter cable so that it spreads over all the cavities inside the motor, then tighten the spark plug into place. After that, it is necessary to disassemble the rod, if it is disassembled, cover with a preservative lubricant all iron parts that may rust and further store the trimmer in a place protected from water.

After completing work, it is necessary to wipe and curl the wires and extension cords with electric trimmers, and put the battery in the battery for charging, because it is not recommended to keep the trimmer even a very short time with a discharged battery. this leads to a quick failure. After that, the head should be removed, because you will have to clean both the protective cover and the inside of the drum itself. If this is not done, the grass juice may dry on them and cause the bobbin with the mechanism that fixes the fishing line to finish working normally the next time it starts.

Preparing electronic trimmers for long-term storage is much easier. The main thing is to protect them from water getting inside the control circuit and the motor, as well as from rust on unprotected iron elements with the help of preserving lubricant. It is imperative to charge the battery before storage, then your spring trimmer will be like new.

Procedure

1. Make sure the mower is set to the correct mowing height. Different types of grass require different mowing heights. Is it possible to mow wet grass with a trimmer? Living permanently in a personal house, it is easy to observe the periodic schedule of lawn care. Determine the type of grass on your lawn before setting the cutting height on the lawn mower.

2. Keep the mower in good condition. Even if you don’t use a lawn mower, it’s important to keep it in good condition throughout the year. Just like in a car, you must be sure that all the nodes of your lawn mower are working correctly, before starting to mow the lawn. Koshu trimmer, if time is short, Grass can be mowed at any time of the day. If the knives of the lawn mower are not ground, this can destroy the lawn for you, leaving part of the grass not mowed and susceptible to disease. Rule weed mow.

3. Try to mow the lawn when the street is not very hot. It is better to mow when there is morning dew on the grass. High temperatures can be very unsafe and this should always be taken into account.

4. Check for debris on the lawn. Before mowing the lawn, it is important to check whether there is debris in the grass, at least some debris can destroy the lawn mower. It is necessary to make two passes along the edge of the lawn. Do not forget to block passageways.

5. We must try to mow the same area every time in the opposite direction. If this is not done, the lawn can be very worn out or damaged in some places.

6. Cut the grass around the flower beds, trees, and in all places where the lawn mower is not reached, to a height similar to a lawn mower (the trimmer can also be called a lawn mowing, lawn mowing, brush cutting or electric cutting). Grass mow. When mowing with a trimmer, you need to be careful not to destroy the bark of trees and not to cling the ground with a trimmer.

7. It is necessary to alternate the mowing direction along and across, up and down, in various cross directions of the lawn. But you need to keep in mind that you can mow a lawn mower only by pushing it forward and under no circumstances can you pull a lawn mower toward you. It may be dangerous.

Tips (mow grass)

Try to keep the mower constant and speed with the throttle. This will provide a more even haircut, extend the life of the engine and reduce fuel consumption.

After you trim the weed in hard-to-reach places for the mower with a trimmer, you need to put the Kromkorez nozzle on the trimmer and cut off all the edges of the flower beds and paths; you also need to remove the grass growing from the cracks in the paths.

Do not exceed speed when operating the mower. At the highest pushing speed of the lawn mower, you may not have time to react and run into a stump, wire or stone in the grass.

Check that the mowing height of the grass on the lawn mower is set to the recommended height for the type of grass on your lawn.

Mowing the lawn is possible only when it dries. If your lawn is wet after rain or watering, then the lawn mower may become clogged with wet grass or soil. In addition, the movement of a lawn mower on a wet lawn can lead to compaction of the earth and lawn diseases. This can ruin the entire lawn.

Procedure:

1. Can I Mow Grass with a Trimmer After Rain Prepare your own trimmer for work. If you have a gas trimmer, check if there is fuel in the tank. If you have an electronic trimmer, plug the plug into the electronic network and check if there is enough extension cord to the farthest corners of the area to be mowed. If you have a battery trimmer. check if the battery is charged.

2. Hold the trimmer as close to the ground as possible to find the best position before you even move.

3. Turn on the trimmer (press the throttle button) and start mowing, moderately moving the trimmer from side to side and taking a small step forward, thereby cutting grass and moving forward. How to mow weed.

4. If there are pebbles in the path of the trimmer, this greatly accelerates the wear of the trimmer line, which will require more frequent substitution of the line. How to use a trimmer.

5. If you see that the grass has become smaller and cut badly when you mow it, the fishing line has worn out, it has become shorter and it needs to be released more from the trimmer head.

6. Stop for a couple of minutes if there is even a slight lethargy. Although mowing with a trimmer is not the hardest work, but if you work hard, your back and arms will hurt for a number of days. If you have obstacles with your back, wear a brace so that it is not difficult to mow with a trimmer.

7. Do not try to trim the grass to the ground with a trimmer. If you mow grass like this, the trimmer head will become clogged with soil, there will be a large consumption of fishing line, and the lawn, yard or plot will look very uncomfortable. It is necessary to mow so that the stubble has a height of about 5 cm, and the surface is very even. Then you can turn off the trimmer and finish the job.

You will need things

Pants. Durable work jeans without holes are desirable. You can mow the grass anywhere, because if the legs are not protected, soon you will feel how several thousand ants crawl along your legs and bite you. Is it possible to mow wet grass with a trimmer? Living permanently in a personal house, it is easy to observe the periodic schedule of lawn care. From time to time, the weed can scratch up to the blood or very quilted, thrown back by the trimmer back to the mowing. Gloves are fingerless, leather, it does not matter. If you mow the grass without gloves, then by the end of mowing you cannot move even your little finger without pain. The weight of the grass through the trimmer presses on the hands and on the hands will appear abrasions and scuffs, if they were not in protective gloves. Safety glasses. you cannot mow with your eyes closed, as small pieces of grass fly into your face. One not bad eye contact will assure you that safety glasses are imperishable. This refers to one of the basic rules on how to use the trimmer. Have enough drinking water under your arm. Even if you think it won’t be hot, think again. For you, how to mow the grass with a vibrating trimmer is quite long. Have a spare fishing line or a trimmed trimmer head to change if completed. If you have an electronic trimmer, you need to have an extra extension cord. If you have a gas trimmer, you need to have a supply of fuel. Rake to rake grass or weeds. A hat if you work in the sun. The highest shoes (trousers are better to fill in shoes). If you plan to work at dusk or later, clap so that you have an insect spray and a lantern.