How To Start A Stihl 180 Chainsaw Cold • CIMFLOK.COM

What happens at the moment of priming fuel with a primer, and how it helps to make dust more efficiently?

At the moment of starting the saw without a primer, several movements of the starter are carried out only so that the fuel pump, under the influence of an impulse from the saw crankcase, pump fuel into the carburetor.

A pump installed in the fuel line allows you to manually pump gasoline into the carburetor without unnecessary movements with the starter. The effect of this action is obvious, the saw will start much faster.

It is necessary to use a primer on a hot chainsaw, because there is enough fuel in the carburetor to start.

How to start a Stihl chainsaw

All Stihl chainsaws are equipped with two-stroke engines, the cold start of which has a similar algorithm. But there are models on which additional equipment is installed that allows you to bring in dust without excessive efforts. For this reason, the algorithm for starting them may differ slightly.

Let’s take a look at how to start regular dust and how the process differs from starting a modified model.

How to get dust after long periods of inactivity

I can’t start the chainsaw after a long period of inactivity. Such comments can be found on the forums dedicated to the repair and maintenance of dust. Let’s figure out how to start a chainsaw after a long downtime.

The fact is that a successful start after downtime must be taken care of in advance and the dust must be properly prepared for storage. According to the manufacturer’s instructions, before storing, it is necessary to drain the fuel from the tank, then start the engine and burn off the fuel in the fuel system.

Preparation is necessary so that during storage, the carburetor membranes do NOT stick together. Performing this simple operation will allow you to successfully add dust after long-term storage.

It is much easier to start the chainsaw six months after idle time, if just before starting, through the spark plug hole, add 1. 2 ml of the fuel mixture to the cylinder. This can be done with a syringe.

How to start a chain saw with a decompression valve

Before starting a Stihl chainsaw on which a decompression valve is installed, you must turn it on. It should be noted that there is no decompression valve on the Stihl 250 saw.

After the first flash has passed, the valve will return to normal operation, respectively, after the engine control lever is set to the open position and starting continues, the decompression valve must be pressed again.

The valve operation is shown schematically in the figure below.

In fact, the valve does not make starting faster, it just simplifies the process and makes it more comfortable, because for during launch a person will have to Apply significantly less effort.

We start Stihl MS 211 C-BE

The fuel supply system to the Stihl MS 211 C-BE Chainsaw is additionally equipped with a manual fuel pump, which makes it easier to start the chainsaw on a cold.

The instruction for starting this model of the Stihl chainsaw contains one additional point, which is that before starting the chainsaw on a cold one, it is necessary to pump fuel into the carburetor using a pump. Further, the instruction does NOT differ from starting Stihl 180 and follows the same algorithm.

We start Stihl MS 180 C

The device of this model, in comparison with the previous one, has some differences in the trigger mechanism, but it does NOT carry any changes in the triggering algorithm. The fact is that the ErgoStart system is installed in the Stihl 180 C, which, due to an additional spring installed in the chainsaw starter, reduces the engine resistance when starting.

We start Stihl 180

In order to start the Stihl 180 chainsaw on a cold one, you must follow the algorithm specified by the manufacturer in the instructions for the Stihl 180 chainsaw, namely:

Turn on the ignition and set the engine control lever to the lowest position (in this position, the air damper of the Stihl 180 carburetor blocks air from the air filter, and the throttle valve is fully open, thus the fuel mixture is enriched)
Pull the starter handle several times until the first flash passes (the flash signals that the fuel mixture has entered the cylinder and the saw is ready to start)
Move the control lever one position up from fully lowering (in this position, the choke opens, and the throttle remains in the same position as before)
Pull the starter and start. The saw will start and run at higher rpm due to the fact that the throttle valve is open as much as possible. To set the damper to idle, you must press the gas trigger and immediately release, the tool immediately normalizes the speed.

The Stihl MS 180 Chainsaw is not equipped with any additional devices that can facilitate starting as standard.

Below you can see how to start Stihl 180. It reflects in detail all the main points, and the author’s comments allow you to understand the whole process to the smallest detail.

Starting a Stihl chainsaw almost always follows the same algorithm, with the exception of those cases when a decompression valve and a fuel primer are additionally installed on the chainsaw. These gadgets are designed to facilitate the startup process and do an excellent job of their functions.

If you cannot turn on and start the chainsaw

When all actions are performed according to the established order, and the chainsaw starts to work, then there are malfunctions in its mechanism. Typically, this phenomenon is caused by common and easily fixable problems, such as the absence of a spark, shut off the fuel supply, clogged filter that allows air to pass through. In order to start the chainsaw, you will have to find the reason and take the necessary steps to eliminate it.

Only correct actions should be taken. If a person does NOT know what to do, it is not necessary to commit rash acts. It is forbidden to disassemble the device, you need to be especially careful with the carburetor. You cannot unscrew any screws on it, since if its device became a prerequisite for a breakdown, then it is impossible to repair a chainsaw without professional equipment.

The actions that need to be performed in a strict order are listed. Only when moving from one measure to the second can you determine the exact cause of the malfunction and quickly eliminate it, and not damage other parts. Algorithm of actions performed in case of failures in the establishment of a chainsaw:

At first it is enough to let the device rest. This is especially true for saws that have recently been in operation. It is enough to wait NOT more than 10 minutes, since during this time the mechanism will cool down and in the absence of other breakdowns it will easily start. Sometimes it happens that a candle is poured into the appliance during the institution. If this unpleasant property has occurred, then it is enough to wait a very short pause and repeat all the steps again to start the engine.
The housing cover is unscrewed from the device to remove the air filter. The process of starting up the device is performed if it is absent. Sometimes the reason for the lack of ignition is that the filter is dirty. If ignition occurred without it, then the reason lies precisely in this. To eliminate THESE troubles, it is enough to wash the filter under running, warm water and soap, then Dry. You can also replace the old element with a new one.
The spark plug is removed. The spark is checked. If it does not appear, you need to replace the old candle with a new one. Usually this helps and a spark appears, however in some cases and when replacing the mixture there is a spark.

When a spark appears when it is impossible to make the device work, you must continue to perform the steps described below.

There are times when a spark appears, but the candle itself is moist. This is possible if gasoline gets on it. To get rid of it, it is enough to turn the device over so that the cylinder is facing downwards. Then all the excess liquid will pour out. Next, you should check the combustion chamber, for which you need to pull the starter more than 10 times. A candle damaged by moisture can be replaced with a subsequent check of its effectiveness. If it becomes faulty, you can replace this element with a new one. After THESE actions, you need to try again to activate the device.

Sometimes the candle remains dry. In this case, it is necessary to draw the gas mixture into the syringe and pass it into the cylinder. After that, you should immediately try to start the device. If debris trapped in the carburetor is a prerequisite for a long lack of response to starting attempts, then when removing it, there should be no obstacle to the flow of fuel into the combustion chamber. The mechanism of successful garbage collection is determined by the flow of liquid when filling the gas mixture, so you need to pour fuel with force, and then almost immediately try to start the device.

The muffler is removed. To do this, it is unscrewed and carefully removed so as not to deform the gasket that delimits it from the engine. You need to try to start the mechanism without using an air filter and a muffler, which helps to eliminate breakdowns in THESE structural elements.

Briefly about the launcher

The chainsaw is powered by an internal combustion engine. This is a simple device, the design of which has no special bells and whistles. It usually works properly even under difficult conditions.

Operation is provided by Structural elements:

Carburetor engine (see Carburetor Adjustment).
Centrifugal clutches.
Ignition system, in almost all devices contactless.
Carburetor, which adds air to the fuel mixture.
Fuel system. Its standard device consists of a hose, filter and gas tank, but sometimes it has additional parts.
Starter.
Tire.
Chain (see Chain Oil).
Chain tensioner and brake (see How to sharpen a chain).

1 diagram of a standard mechanism

Before starting the benzoil, it is necessary to move the flap, which acts as an adjustment lever, downwards, in comparison with the optimal position. First, you need to press the button responsible for the gas supply. Only if this condition is met is it possible for the damper to move normally to the bottom end stop. It is necessary to simultaneously move the damper and hold down the gas button. The gas is set to the standard position and the choke closes the carburetor, preparing the unit for correct operation.

The starter handle should be pulled, and this is done with a jerk, and not with soft movements. This action requires the use of moderate force. The jerk data should be continued until the start of ignition of the chainsaw is definitely heard, which ends very quickly (dies down). After the implementation of this event, the position of the damper must be moved one step up.

The starter handle twitches again until the system starts. When the device starts to actively work, a high speed is immediately noticeable, since the throttle stick is at a high level. It must be remembered that sometimes chainsaws are supplied without a starter, then all actions with this element are released.

The gas button is pressed once and then released, then the position of the damper will immediately become optimal. The speed drops, that is, the intensity of the chain revolutions.

An already warmed-up chainsaw starts up when the lever is set to the “1” position, and then actions are taken to turn on the device.

To turn off the engine of the device, you must set the damper to the highest position.

It will also help to make your choice in favor of this or that brand of chainsaw, our other article.

In Russian-made chainsaws. Low price with sufficiently high quality.

Step-by-step instruction

When the brakes are activated, the assembly process is much slower, so everything is also safe and more comfortable, you can turn on the mechanism without the use of braking equipment.

2 diagram of a standard mechanism. how to properly start dust

The ignition is switched on. To do this, move the toggle switch to the desired location or move the switch.
The swap primer usually has to be pressed more than two times. Gasoline is poured into it, after which you will have to press the device more than three times. Sometimes the chainsaw is not equipped with a primer, then you can skip this step.

The adjustment lever, which is responsible for the location of the damper, must be pulled out as far as it will go. Many chainsaws have the ability to block this element. Then it can only be moved while pressing and holding the throttle button. Some chainsaws do not have this lock, which makes them more comfortable to use. For these models, gas may NOT be fixed or retained when using automatic technologies.

You need to take the starter handle and pull it sharply until the ignition is heard. It is celebrated by the institution and by the almost instant engine shutdown. After that, the shutter must be pushed into its original position, checking it until it stops. Then the starter handle jerks again to start the device. Before carrying out this event, you need to make sure that this is the method that will help the chainsaw start. Some devices have a different ignition system. In order for the motor to work in them, you need to move the damper only 50%, and only when the motor starts to actively work, move it completely.

If you have purchased a fixed gas model, you need to prepare in advance for the Highest engine speed immediately after activating the device. When there is no fixation, the initial power is very low, so in most cases it must be increased. If you do not take any action, then in the latter case, the saw runs for a short period of time, and then automatically stalls. If such a situation occurs, you need to start the chainsaw again.

For more details, look at:

How to start a Stihl chainsaw (Stihl MS-180). the first start and start without a starter

Chainsaws differ slightly in design features, but in most cases the assembly principle is carried out according to two standard schemes. In many devices, the instructions contain information on the need to activate the emergency set brake before starting the activation procedure. You should first master the device of the plant and study the main ways of correcting breakdowns, then a person will have the opportunity to fully operate the device. The article will talk about how to start a chainsaw.

The chainsaw should be started by following the standard instructions. If there are any problems with the operation of the device, for example, the chainsaw does not start, it is necessary to quickly eliminate them or take the device for repair, and in order to identify malfunctions and correct operation of the chainsaw, you need to know the features of its design. To learn how to quickly turn on the device and fix breakdowns, it is enough to study the basic range of necessary actions and follow it.
Read on how to properly run your chainsaw before starting it for the first time.

Chainsaw Husqvarna-137: DIY Husqvarna-137 starter repair manual, valve malfunction, sparks

Stihl-180 Will not start: reasons and remedies, why the chainsaw fills the candle, and gasoline does not flow to the cold

How to adjust the carburetor on a Husqvarna chainsaw (Husqvarna). tuning and adjusting the saw

Makita (Makita) 4610 chainsaw DCS461 and saw 4610. user manual

We start Stihl MS 211 C-BE

The fuel supply system to the Stihl MS 211 C-BE Chainsaw is additionally equipped with a manual fuel pump, which makes it easier to start the chainsaw on a cold.

How to turn the Stihl 180 on cold

Country house mirrors

What happens at the moment of priming fuel with a primer, and how it helps to make dust more efficiently?

It is necessary to use a primer on a hot chainsaw, because there is enough fuel in the carburetor to start.

Stihl 180 saw setting algorithm

If you have a question about how to start a Stihl chainsaw, then there is an option to see such a process on the example of model 180. To be able to perform work on a cool one, you need to turn on the ignition and set the engine control lever to the lower position. With all this, the carburetor flap will block the air from the filter, and the throttle will be open, so the fuel mixture will be enriched.

The starter handle needs to be pulled a couple of times until the 1st flash occurs. This will indicate that the mixture has entered the cylinder and the equipment is ready for institution. Before starting the Stihl chainsaw, you need to set the control lever one position up. With all this, the air damper will open, while the throttle remains about the same position.

The starter must be pulled and started. The tool runs at high revs, the throttle valve will be open. To set the latter to idle, use the gas trigger and release it. With all this, the tool should start working normally. On the described model of the chainsaw, comments on additional devices that would make it easier to start.

How to Start a Stihl 180 Chainsaw Correctly

How to start a Stihl chainsaw: starting process and overview

What remains to be done for our client Stihl branded chainsaws have two-stroke engines. Their cool start is carried out using a similar method. But on the market we meet models on the pages of which there is additional equipment, when using it, of course, add dust, and do not make any special efforts. Therefore, the starting method may differ.

We start Stihl MS 180 C

We start Stihl 180

In order to start the Stihl 180 chainsaw on a cold one, you must follow the algorithm specified by the manufacturer in the instructions for the Stihl 180 chainsaw, namely:

Turn on the ignition and set the engine control lever to the lowest position (in this position, the air damper of the Stihl 180 carburetor blocks air from the air filter, and the throttle valve is fully open, thus the fuel mixture is enriched)
Pull the starter handle several times until the first flash passes (the flash signals that the fuel mixture has entered the cylinder and the saw is ready to start)
Move the control lever one position up from fully lowering (in this position, the choke opens, and the throttle remains in the same position as before)
Pull the starter and start. The saw will start and run at higher rpm due to the fact that the throttle valve is open as much as possible. To set the damper to idle, you must press the gas trigger and immediately release, the tool immediately normalizes the speed.

The Stihl MS 180 Chainsaw is not equipped with any additional devices that can facilitate starting as standard.

Below you can see how to start Stihl 180. It reflects in detail all the main points, and the author’s comments allow you to understand the whole process to the smallest detail.

Tips for starting a saw MS 180 C

This device, comparable to the previous one, has some difference in the trigger mechanism. But there will be no configurations in the start method. In the described version of the equipment there is a system that, using a spring in the saw starter, reduces the resistance of the motor.

Let’s take a look at how to start regular dust and how the process differs from starting a modified model.

Faulty plug: troubleshooting methods

Sometimes during the check it is possible to find out that the problem lies in a faulty spark plug. In this case, it is removed, then allowed to dry. Some owners may try to ignite it, but this should not be done, because otherwise this element will be damaged and after that it will only have to be thrown away. During troubleshooting, you will have to remove excess fuel by draining it through a special hole.
You also need to keep in mind that the drying time should be at least half an hour. After completing a similar operation, you can return it to its place, and then test it in action.
In some cases, the candle may fail due to the depletion of its resource. Usually, when this is confirmed, the only option is to find a replacement for it. In this case, it does NOT hurt to have a spare candle, or even better, when you have a whole set of such elements at hand. In this case, you can always put a new candle instead of the existing one and make sure whether a broken candle is a prerequisite for a breakdown.
At the same time, the inability to start the chainsaw can be caused by a weak contact provided by the high-voltage wire and the end of the candle. The problem with starting the chainsaw may be due to the failure of the ignition unit. In such situations, the only solution to the problem is to replace the faulty unit, since it is not repairable.

Saw won’t start: reasons and solutions

Speaking of dust 180, it must be said that this tool has many advantages. At the same time, NOT only this unit and disadvantages. Attention will be paid to them.
It is a common situation that many owners find themselves in when the Stihl chainsaw does not start and fills in a candle. This is usually attributed to the theca formation of the oil used to lubricate the chain. The same happens for the reason that over time, the area where the hose of the oil pump and the oil tank joins loses its former tightness.
In principle, this problem is solvable, but in order to do everything correctly, you need to take into account the design of the chainsaw in question. By itself, this process provides for certain nuances, first of all, it is necessary to disassemble the unit, and without this it will be impossible to get to the right place.
For many owners of this saw, the question is, why does the Stihl 180 chainsaw not start? Experts give the following recommendation on this matter: the first thing to do for those who have encountered a similar problem is to open and then close the lid located on the gas tank. There is another solution. you need to remove the candle and let it dry. You can also create the effect of artificial ventilation for the combustion chamber. Most often, these recommendations are enough to bring the device back to working condition. However, this does not always help to restore the operation of the Stihl chainsaw.
If there is a spark, but attempts to start the chainsaw lead to nothing, then in this case you need to check the supply of gasoline, the air filter, and then make sure that the spark plug is working. Such manipulations must be done for the reason that most often this kind of malfunction is caused by contamination of the breather. And if a plug forms in it, then, naturally, a vacuum environment will be created in the gas tank, due to which the fuel will not flow. A similar problem can be solved quite simply, for which it is enough to remove the dirt using a needle.
Some owners face this problem when the saw itself starts, but immediately starts to stall. Look for the reason that the saw does not start, you should go to the carburetor. Most likely, he managed to get clogged and afterwards does not allow the tool to work correctly.
To make sure that the breather is NOT the cause of the malfunction, and it is in working order, you must first disconnect the fuel hose from the carburetor, and then find out if this or fuel is generated.
Keep in mind that it is natural for your chainsaw to have a strong and stable jet of gasoline. In addition, it is often possible to observe a situation when the Stihl 180 chainsaw does not start hot and immediately stalls at the same moment or after a while. Usually a similar malfunction is associated with a muffler. Most likely, it has accumulated a lot of deposits associated with long-term operation of the tool, which is usually accompanied by the formation of exhaust.
At the same time, the saw may stop starting if the tool chain is poorly lubricated. This can be facilitated by channels that have a plug, or the reason should be looked for in an oil line that has a leak.
Theca in the connecting pipes or in the place where the oil pump fittings are installed can become a serious problem.
There are cases when the Stihl 180 chainsaw begins to stall due to a failed cylinder. To make sure if this is really so, it is enough to conduct an inspection. If, as a result of the examination, you find irregularities and chips, then this is a clear sign of breakage.

Clockwork device

As with other saws, the carburetor acts as the main starting device. Considering in more detail the carburetor, which the Stihl 180 chainsaw is equipped with, it should be noted that it has a single tuning screw. In other words, it is a kind of idle speed adjustment screw. In this case, the nozzle, which has a full load, is stationary all the time.

In other words, the regulation is not applicable to it. In turn, there is no way to influence the full load in any way. You also need to pay attention to the factory settings, because of which the air / fuel mixture is supplied directly to the engine. over, this principle remains regardless of the operating conditions of the tool.

Stihl 180 chainsaw does not start: main reasons

Today, many manufacturers are engaged in the production of units for agricultural and construction work, among which the most demanded is the equipment manufactured by Stihl. The high level of quality is not the only reason why the products of this manufacturer are popular in the market. This was also facilitated by the democratic price and optimal power that the models of this brand have.

It seems that many have had to use a chainsaw of a similar brand. And not just use, but regularly perform a wide variety of work and make sure of the high performance characteristics of this tool. Such distribution of THESE products is no coincidence, considering that in addition to power, this instrument stands out for its graceful design. However, one must remember that this is still a technique in which the resource of work is limited. Therefore, each owner of such a unit at some point is faced with the need for repair. Next, we will talk about the features of repairing the Stihl 180 chainsaw.

Main characteristics

The dust in question can be considered a compact option, because its weight is only 3.9 kg. At the same time, it has a large oil and fuel tank. A two-stroke engine helps the device to perform its working functions, the power of which is sufficient for solving simple tasks. In addition, this instrument does NOT generate a lot of noise during operation, the level of which does NOT exceed 98 dB. For ease of understanding, it is enough to say that human speech creates noise at a level of 76 dB.

The Stihl 180 chainsaw has a power of 2.6 watts. In principle, this is enough, remember that we are talking about a tool for household use.
The capacity of the oil tank is 0.145 l, the fuel tank is 0.25 l.
Designed tire measures 350mm with 0.325 ” pitch.

General information

The characteristics of this saw are a reason for the pride of the German manufacturer. In this case, the unit is a tool, which is designed to perform a small amount of work. The tool is positioned for domestic use, which confirms the intensity of its use, which does not have to exceed 20 hours per month. Having at your disposal such a unit, it will not be difficult to maintain order in your garden, to prepare firewood for the winter, as well as to clear areas. At the same time, he will be able to help you in solving other problems where there is no need to perform complex manipulations.

Other malfunctions

For many owners, the question of the correct idle speed after emptying the fuel from the gasoline tanks is relevant for many owners. According to experts, there is no need to worry too much about this. However, if you have to deal with a similar problem often, then it is enough to manipulate the carburetor by reducing the engine speed in order to restore the normal operation of the tool.
In some cases, the owner may need to clean the muffler as this part may be the cause of the malfunction. This operation is easy enough. It must be remembered that many owners are faced with problematic chainsaw operation due to a faulty carburetor.
Although in SEPARATE cases it can be quite simple to eliminate the malfunction, it is most preferable if specialists will repair this equipment. After all, not every one of us has the necessary knowledge and skills, and this is fraught with the fact that during self-troubleshooting there is a risk of completely disabling the tool.

The chainsaw simplifies many operations. However, for a long time she cannot demonstrate her original level of work. Therefore, at some point, problems may arise. Naturally, the owner can eliminate some malfunctions on his own, but in any case there is a risk that he will incorrectly determine them, and this is fraught with the fact that by his actions he can completely disable the tool. Therefore, it is advisable NOT to take the initiative, but to entrust this work to a specialist.

Sources:

http://machinspec.com/lesozagotovitelnaya/benzopila/kak-zavesti.html http://crast.ru/instrumenty/kak-zavodit-shtil-180-na-holodnuju http://nashgazon.com/instrument/pily/ne-zavoditsya-benzopila-shtil-180-osnovnye-prichiny.html