How to switch your drill to a rotary hammer

Let’s understand the construction and principle of operation of the torch

The following device groups are distinguished by weight and purpose:

Medium (semi-professional) ploughs. 5-8 kg.

Heavy (professional) gaolers. 8-10 kg.

Household peorators

Peorators weighing less than 4 kg are considered to be lightweight. They are bought for occasional repair work in the home or garage. Better known as “household gaolers.

Semi-professional gimbals

To the middle class belong the semi-professional tools with weight from 5 to 8 kg, they are characterized by higher power and force of blow (5-7 J). The tool can even cut through a steel lattice, not to mention a hole in a concrete wall.

Professional gaolers

The heavy class includes gimbals with weight more than 8 kg and impact force more than 8 J. Tool is designed for continuous, nonstop work. Usually used by repair crews, so called professional. The purchase of a heavy torch for domestic use is not a justified investment.

Principle of independent connection of a drill or a gorator

Portable cordless power tools are used to connect corded power tools in the field or in the absence of a fixed power supply. They are lithium batteries, made in a waterproof case with built-in BMS board and charger. The voltage of such batteries is usually 12 or 24 V, but they can also be connected to conventional power equipment with operating voltage of 220 V.

For this portable battery connected to the inverter, which converts the voltage from 12 or 24 V to 220 V of the required capacity. The peorator, drill or other equipment you use is connected to it. Actually portable battery is a large Power Bank for various tasks: repair and construction, household, travel. In addition to power tools, you can connect a kettle, laptop, refrigerator, TV, microwave and other power-consuming devices.

Advantages

Stand-alone connection of a drill or torch provides them with the following advantages:

• Mobility. the ability to use corded tools in the field, in the woods, vegetable garden, field, garage, etc.д.
• Autonomy. independence from the availability of utility power and the proximity of electrical outlets.
• Ease of use in the home and professional sphere. when repairing, building, assembling and disassembling various constructions.
• Expanding the use of power tools.
• Able to carry out planned work without forced outages due to power supply interruptions.

Portable rechargeable batteries give these advantages to cordless power tools. They store electricity while they are charging and give it back to the motor when the drill, torch, or other equipment is connected. Battery must be compatible with the device in terms of power capacity and have sufficient capacity to provide the necessary autonomous work time of the equipment. Its value depends on the power of the appliance and the capacity of the battery pack.

Pluses and minuses of work without a button

When using an electric drill without a power button, there are many more disadvantages than advantages. The only advantage of this connection scheme is that there is no need to replace or repair the breaker. However, in the case of a direct connection of the drill to the network, there are many problems. For example, the functionality of the device suffers.

It is impossible to adjust the rotational speed or switch to reverse without the switch. In addition, this connection will not be available with the soft start function, which is equipped with most modern models of high-power electric drills. Also, before each use of the drill you must plug the power cord into the outlet, and then turn it off after work, which is not very convenient.

When connected directly, without the possibility of independent adjustment of speed, the motor of the device will immediately start working at full power. In addition, the contact groups of the switch, when the power tool is turned on, take on part of the load. If it is absent, both the motor winding and the brushes will be subjected to increased stress. This will cause the motor of your power tool to wear out and fail very quickly.

Reasons for no shock

At first sight it seems that the striking mechanism has a simple design, and there is nothing to break there. Stress, dust and vibration gradually take their toll. The impact force usually diminishes as the mechanism wears and eventually wears out. The sudden disappearance of the striker is due to the deformation or destruction of some parts.

Kick and striker

These parts are made from high strength steel. The striker fails seldom, but the sleeve, in which it moves, absorbs some of the shock energy and is destroyed over time. The splinters jam the striker and the motor stops striking.

The striker (“flying piston”) has a compression ring. When it is worn, some of the air flows into the gap between the cylinder in the barrel and the firing pin. The more wear, the weaker the shock. Fixes the problem by replacing the ring with a new one.

Sometimes the striking part of the “flying piston” breaks on the beater. Usually a result of the drilling pressure on the piston. No increase in drilling speed, but increased stress on the mechanism that accelerates wear. Repair by chamfering with an emery machine or replacing the part.

“Drunken bearing

It is angled on the shaft and drives the piston. If the bearing is worn or fractured, it must be replaced.

Mode Switch

Parts of the mechanism can come out of the guide grooves. This can be the result of deformation, wear and tear or frequent use of the tool when not fully engaged. This can be corrected by re-positioning the parts or replacing them with new ones.

Lubrication

Failure to replace the lubricant promptly may also be the reason for no shock. Work with a torch requires the presence of dust, which does not affect the properties of lubricants. Dust may clog the cylinder openings intended for air circulation during percussion machine operation. The same effect is possible if excessively thick lubricant is used, which is not intended for the pedal.

Button Replacement

You will need a flathead screwdriver, a Phillips screwdriver and an awl for this procedure. If you don’t have the latter, a sack needle or any other thick needle will do. If the model is small, you can also use tweezers for more convenience.

• Loosen a couple of screws that hold the power cable.
• Insert the awl into the stator near the wire and carefully remove the wire.
• Pull out the second cable in the same way.
• If the button is not fixed with clips, unscrew screws and take it out.
• Insert a new key and connect the wires with an awl.
• Put the block on the drill, remembering the reverse.
• Carefully place the strands and tighten them with the screws.
• Close the cover.

In a good half of the cases, the wires coming from the stator are different in color. If they are the same, then they must be labeled so as not to be confused when connecting them.

SDS chucks and adapters

Useful information

In this section you can find all the necessary accessories for working with the pen. cartridges and adapters for the pen. Chuck for the orator is one of its most important parts because it is used to fasten the working tool, which later performs the operation.

Constructively the chuck is a hollow cylinder, which at one end is attached to the shaft of the tool, and to the other end of which the drill, drill bit, etc. is attached. д. Chucks for rotary table saws, drills, etc. д. To fix the tooling in these chucks it is necessary to use special wrenches and quick-chuck (this is more convenient in use, when no additional devices are required for fixation of the tooling, it is replaced in a few seconds by hand).

All accessories, which can be purchased, should be divided into several groups:

• SDS chuck. this type of chuck allows to use drills and core bits with certain type of SDS shank. There are SDS-plus and SDS-max chucks, which enable to use tools with SDS-plus and SDS-max shank respectively. SDS-plus shanks are most common and used in lightweight construction machines, respectively SDS-plus chucks are most often used for household purposes.
• Adaptors for rotary tool are inserted into a chuck of rotary tool and allow the use of accessories with one type of shank for working with rotary tool with another type of chuck. For example, an adapter from SDS-max to SDS-plus allows you to use tools with an SDS-plus shank, even if the chuck is designed for SDS-max. Conversely, the SDS-plus adapter allows the use of drills and drills with the same shank, even if the chuck of the torch is designed for another type.
• Peorator adapter chucks. this type of SDS adapters are especially useful when you need to use one peorator and several drills and drills with different types of shank. The difference lies in the design of the adapter. on one side there is a shank of the required type, and on the other side. a chuck. For example, SDS-plus chuck allows you to work with small SDS-plus tools with large SDS-max construction tools.

In our webshop you can find a wide range of drill bits and different types of adapters. To buy them is very simple. you need to call the toll free number 8-800-333-83-28. Our polite and experienced manager will give you all the information about delivery terms and prices.

Reviews on sDS Peorator Chucks and Adapters

SDS Peorator Chucks and Adapters

Useful information

In this section you can find the necessary accessories for working with the torch. chucks and adapters for the torch. Chuck for a rotary tool is one of its most important parts, because it is in this chuck that the working tool with which the operation is subsequently performed, is fixed.

Structurally the chuck is a hollow cylinder, which is secured to the rotary shaft of the tool at one end, and a drill, drill bit, etc. is attached to the other end. д. Chucks for torches, drills, etc. д. chucks are of fist type (for fastening of accessories in them special keys must be used) and quick-clamping type (more convenient in use chucks, when no additional devices are required for fastening of accessories, and the change takes place manually in a few seconds).

All the tooling that you can buy should be divided into several groups:

• SDS chuck. this type of tooling allows the use of drills and drills with a specific type of SDS shank. There are SDS-plus and SDS-max chucks that allow you to use tools with SDS-plus and SDS-max shank respectively. SDS-plus chucks are most common and used in lightweight construction machines, respectively SDS-plus chucks are most common in household appliances.
• The grip adapters are inserted into the grip chuck and allow you to use tools with one type of shank to work with a grip with another type of chuck. For example, the adapter from SDS-max to SDS-plus lets you use accessories with an SDS-plus shank even if the gator chuck is designed for SDS-max. Conversely, the SDS-plus adapter also makes it possible to use drills and core bits with the same shank even if the lever chuck was not designed for this type of chuck.
• Drill chucks. this type of SDS tool drive is especially useful in case of necessity to use one drill bit and several drills with different types of shank. The difference lies in the design of the adapter. on one side there is a shank of the required type, and on the other side. a chuck. For example, SDS-plus chuck allows you to work with small SDS-plus tools with large SDS-max construction tools.

In our online store you can find a wide range of cartridges for the hole punch, as well as different types of adapters. It is very easy to buy them. you just need to call the toll-free number 8-800-333-83-28. A courteous and experienced manager will provide all information on delivery times and costs.

Reviews on sDS punches and adapters

GBC 3230ST Electric hole punch / stapler for 2-3 holes

Features electric hole punch GBC 3230ST

• GBC 3230ST is a double-function electric stapler punch
• Punches and staples up to 24 sheets at a time
• Provides convenient push-button control for user convenience
• Has standard peorating patterns with 2 or 3 holes that can be customized as desired
• Equipped with alignment guide for precise and delicate penmanship
• Offers a staple guide that provides staple alignment.
• Extra-large throat for large format paper
• Comes with wide chip drawer with clear window
• Features a jam reverse knob to prevent any obstructions in the process
• Automatic document detection for timely filling of pin compartment and trouble-free stapling.
• With a one year limited warranty

Overview of the GBC 3230ST electric hole punch stapler

The GBC 3230ST electric hole punch stapler is a unique tool that allows you to perform peorating and stapling tasks with one device.It is designed to fit in any environment without any compromise in quality. With this amazing tool, users can work with 24 sheets for faster reeling and stapling. This GBC hole punch system has 2 and 3 hole modes, each of which has its own characteristics for different levels of piecing and stitching.