How To Wind The Line On A Lawn Mower

Safety engineering

To quickly and safely change the line on the reel of the mower, you must observe safety precautions. Before removing the reel to rewind the line on the mower, the technician must be disconnected from the power supply (if the mower is powered by electricity). Here I would like to mention the rating of electric lawn mowers in terms of reliability, which will help you choose a safe helper.

Another important safety rule that must be observed is pressing the lock button. You can find out its location on the vehicle body using the operating manual. For example, you can find the operating instructions for the manual petrol lawn mower here.

Do not forget that the cutting element needs to be adjusted. There is an adjustment button on the body of the unit. If the process does NOT start automatically and the thread tension has been released, then the button is clamped and the fishing line is pulled out of the spool with force.

See instructions.

Mower line device

The device of the element on which the nylon thread is wound is very simple. This element is called a coil. It has two “tracks”. an upper and a lower one. Between these tracks, there is a special partition with a recess. A fishing line is wound on these tracks. It must first be pulled through the recesses.

Features of replacing the fishing line with.

How to fill a line in a lawn mower: how to change and load into a reel, how to change and how much to wind into a trimmer

When spring comes, people often spend their free time at their summer cottage. They try to rid their area of ​​problems such as weeds and grass with the onset of warm days. It is difficult to do this manually, especially if the area is very large, so a lawn mower will help. Thanks to this technique, you can trim the grass and remove weeds. it is a suitable device for mowing unnecessary plants near the fence, at home, between rows in the garden on a flower bed, and so on. Read about how to choose the right lawnmower for your needs here. The cutting element in this device is a fishing line (strong polyethylene thread), which is wound on a special element. a spool. But over time, the line wears out and it becomes necessary to replace it. The article will talk about how to fill the line in a lawn mower.

Replacement instructions. how to insert the line

It should be noted that the reels in mowers can be different:

• For functioning with one tendril;
• For functioning with two tendrils;
• The fishing line must be threaded through the through hole, which is located inside the element.

B do not confuse this part with an extension cord for a lawn mower on a reel, because despite the similar name, these are two completely different elements.

This article will tell you about how much the ZIL 130 dump truck weighs and what this transport is capable of.

Read here //machinspec.com/lesozagotovitelnaya/benzopila/stanok-dlya-zatochki.html how to assemble a machine for sharpening chainsaw chains with your own hands quickly and easily.

In the first option, winding the cutting element is very simple:

• There is a locking tab on the inside of the spool element.
• One whining tendril is inserted into it.
• It is necessary to thread the nylon thread in the direction opposite to the rotation of the spool element.
• You will need only 2 to 4 meters of fishing line. When the winding process is completed, put the small end of this cutting element outward and fix it in the groove, which is necessary for fixing the fishing line so that it does not unwind during the operation of the mower.
• If there is a special groove, then the end should be held by hand so that the cutting element does NOT unwind during further assembly of the element.
• At the last stage, it is necessary to thread the outer end of the thread into a special hole located on the outer part of the element. The spool can then be inserted into the mower.

When the roller is working with both ends of the plastic filament, then the following steps must be taken to thread the line into the mower:

• Inside, on the spool, you will see how many recesses there are for winding (two or one). If the groove is equal, then both ends of the thread will be guided through this groove. If there are two of them, then the antennae are laid out separately. each in its own notch.
• It is necessary to unwind from 2 to 4 meters of polyethylene thread and thread its two ends into the hole.
• Wind both threads in the same direction, opposite the rotation of the drum.
• When all the line is wound, the ends should be fixed in the grooves or held by hand.
• Both ends are threaded into the eyelet from the outside of the roller housing.
• The drum is then collected and inserted into the mower.

Tips and steps for changing the line to.

The spool element or roller may have a completely different design from the previous two options. The line can be threaded through the eyelet, which is through and located inside the spool. In this case, it is not necessary to disassemble the roller drum and manually wind the polyethylene thread.

The polyethylene thread is threaded through the hole and rotated by pressing a special button. This button is located on the body and is intended for the operation of the equipment so that it is possible to release the fishing line as it wears out.

Which line to choose to refuel lawn mowers

The thickness of the polyethylene thread depends on the model of equipment and varies from 1.2 to 4 mm. She may be:

• With a round cross section. this is the most durable material for mowing grassy plants;
• With a curly section. used for mowing soft plants;
• Twisted. used for thin grass;
• Professional type, not suitable for all models of equipment.

To change the line for lawn mowers, you need to purchase a cutting thread that will be ideal for the type of mower.

If you have a summer cottage or a large plot of land near your individual house or cottage, then for the convenience of cleaning grass and weeds, you must use a lawn mower. In case you are thinking of choosing an electric or gasoline lawn mower, then click here and you will find comparative characteristics of different models.

Over time, the line on the mower wears out and needs to be replaced. you can do this yourself. The choice of this polyethylene thread is necessary depending on the model of the mower. It is also worth keeping an eye on the rest of the unit’s details, here, for example, you will find information about Craftsman lawn mower blades, which also wear out and can lead to irreversible consequences.

The device of the reel into which the fishing line is inserted is very simple. But it differs depending on whether the coil works with one or two whine tendrils. It is important to observe safety precautions when changing the line in the reel.

How to insert line into the trimmer spool? Instruction

The warranty production of the factory trimmer refueling will inevitably require line replacement. Having a very rough idea of ​​how to thread the line into the trimmer reel on their own, beginners are reluctant to take up this business. However, with some skills, mastering this simple teaching does not present any difficulties, and the similar instruction presented below will make this process as easy as possible.

How to tuck a string into a lawn mower. Preparation. remove and disassemble the spool

On most electric and petrol trims, you will need to remove the spool to replace the line. The FUBAG tool lets you skip this step. To make the instruction universal, we will still consider it in detail:

Lock the shaft. Insert the locking element into the corresponding hole. It can be a thin screwdriver or a metal rod.

Unscrew the bobbin case. In our example. strictly clockwise.

Unscrew the cover in accordance with the direction indicated on the body.

Take out the winding spool.

The preparatory stage has been passed. You can go to winding the fishing line.

How to choose a fishing line. length, diameter, restrictions

IMPORTANT Remember! Do not use fishing line or metal cables for the trimmer. This substitution is ineffective and dangerous. The rope can injure Not only the mower itself, but also those around.
As for the length, you should count on the estimated frequency of use of the trimmer. The more often, the more it costs to stock up the expense.

Information about the possible line diameter can be found on the body trimmer spools. Most likely, the range will be indicated there. The thickness varies from 1.2 to 4 mm. Choose the appropriate option, taking into account the peculiarities of the cultivated area. The larger the diameter, the easier it is to mow tough grass.

Trimmer head types

The main elements of the trigger is the mowing head, which is a cylindrical body with a spool (bobbin) inserted inside. The fishing line (cord) is tucked into it. The heads differ from each other in the way of feeding and threading the cord. There are three types of heads in total:

• Automatic. The line is then fed as the user decreases the engine speed. Automatic cord feeding is very convenient when there is a lot of work to be done. The disadvantage of such a head is the high consumption of whining.
• Semi-automatic. The use of such a head does not require the user to perform any complex manipulations. The principle of its operation is designed so that the line begins to automatically lengthen while the trimmer is operating at full speed. You just need to lightly hit the ground with the head of the machine (this will release the blocking of the chain), and the cord will be pulled out of the bobbin due to centrifugal force. Then the line is cut to the required length with a knife, which is located on the protective casing.
• Manual. To lengthen the cord, the machine must be stopped. After that, the line will need to be pulled out manually.

Trimmer coil types

Studying the trimmer passport.

The passport contains the technical characteristics of the trimmer: motor power, equipment, mowing head device, type of line feed, purpose.

How to wind the line correctly on the trimmer reel. Step by step guide

Preliminary preparation

First of all, to wind the fishing line, you need to remove the spool (bobbin, spool) from the trimmer. specific actions will depend on the complexity of the configuration and the type of the product itself:

• Small electric trimmers with a working position of the motor and the coil in the lower part, as a rule, have side buttons on both sides of the bobbin. When pressed at the same time, the upper part of the spool together with the inner content for winding the line is disconnected, while the lower part remains on the trimmer. It is advisable to disassemble the bobbin on a flat, smooth place so that the spring included in the structure does NOT jump out and does NOT get lost;
• Electric and gasoline trimmers with a curved bar without the possibility of installing a knife, as a rule, have spools with special lamb: in such designs, hold the spool in a stationary position with one hand, and rotate the wing nut that fixes the Bobbin on the bar with the other hand. After disconnecting the nut, the entire bobbin is removed.
• Electric and gasoline trimmers with the ability to install a knife on a straight Bar (for example, Stihl trimmers) have a hole under the reel. To keep the rod stationary, a screwdriver or other suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bobbin is fixed. After that, the coil body is scrolled clockwise (with a left-hand thread) and removed from the trimmer.

For the second and third options, the coils, depending on the design, are disassembled in different ways. In the bobbins, a lamb is unscrewed from the lamb, in the coils, the latches are pressed from the latch and one part of the coil is released from the other. If the halves of the bobbin are connected by thread, then it is enough to turn them by hand in opposite directions until they are completely unscrewed.

Step-by-step instructions for threading the line into the trimmer.

1.Push the clips inward until they click and remove the cover from the mowing head.

2.Check the spool carefully, it will free itself from the holder, and now remove it.

Coil with one working tendril

The simplest option and uncomplicated sequence of actions:

• The dimensions of the reel and the length of the original factory winding determine the recommended length of the line for winding. 2. 5 m.
• One end of the line is inserted into the fixing technological hole located inside the spool.
• The fishing line is wound on the drum in the reverse rotation of the spool in the direction of the trimmer. as a rule, on the inside of the bobbin an arrow indicates in which direction the winding is being carried out.
• A small section of the fishing line is left free to lead it out. it is fixed in a specialized groove on the inside of the bobbin, designed to hold the winding when assembling the bobbin into working condition.
• The left end of the line is passed through the hole in the outer part of the reel.
• The bobbin halves are assembled and put on the trimmer bar.

Trimmer head with automatic line threading

Types of trimmer heads

Some models on the market are fitted with a reel with an automatic winding mechanism. It is enough for the owner to properly thread and fix the ends in the head, and the winding operation will be performed by the tool itself when it is turned on. It is almost impossible to wind the line incorrectly into a trimmer with such a head, since the coil independently determines the position of the antennae. The advantages of the automatic trimmer head include the ease of threading the line, and the disadvantages are frequent breakdowns of the mechanism due to the complexity of the design and the high cost.

Removing the coil from the trimmer

On small electric trimmers with a bottom-mounted motor (when it is in the ground while working), the reels usually have two keys on the sides. Click on them and disconnect one half of the coil body from the second, which remains on the trimmer. Together with the first half, the inner part is also taken out, on which the fishing line is directly wound. When disassembling, be careful: there is a spring inside that can fly out and get lost.

On electric and gasoline trimmers with a curved bar (there is still no way to put a knife on such trimmers), you need to grab the coil body itself with one hand, and with the other hand you need to start rotating the lamb on it counterclockwise. It is he who attaches the coil to the Trimmer Bar. Having unscrewed the lamb, carefully remove the entire coil, trying NOT to lose the spring inside.

On electric and gasoline trimmers with a straight bar and a gearbox at its end (on such trimmers, in addition to fishing line, you can also install a knife), we look for a hole under the coil, insert, for example, a screwdriver into it, quietly rotate the coil until the screwdriver does NOT crawl even deeper and the coil will lock. Now steep the whole coil clockwise (since the thread is left-hand) and remove it from the trimmer. Then we disassemble the coil. It can be assembled using snaps or a twisted lamb. If the coil is on latches, then press on the sides on the base of the latches so that they bend and release one half of the coil body from the other. We just unscrew the lamb. There may also be a third type of connection between the two halves of such a coil: with it, you need to grab the lower part with one hand, and the upper part with the other, and start turning them in opposite directions. When disassembling such a coil, you also need to make sure that the spring inside is not lost.

Single Barbed Trimmer Spool

Reel for single-barb lawn mowers

Many owners and experts note the ease of use and ease of refueling the bobbin with one mustache. Depending on the manufacturer, the length of the threaded line can vary from 2 to 5 meters. The end of the line is inserted into the head into a special technological groove or hole, and the winding is carried out in the direction opposite to the working rotation of the bobbin. Most reels have arrow marks on the outside of the body that indicate the direction of the trimmer reel movement.

After winding, you need to leave a free end of 15-30 cm to enhance the centrifugal force, which is decisive when removing the trimmer line in automatic and semi-automatic spools. Passing the left end through the working hole of the coil and assembling the head.

How to wind line on a trimmer reel: key points

A gasoline or electric trimmer is an indispensable tool in the arsenal of a modern summer resident or owner of his own home.

Thanks to these garden devices, even a large garden plot can be mowed with ease. After purchasing this tool and performing several mows, many people think about how to properly wind the line on the trimmer reel. For an inexperienced user, the first operation to replace it will seem problematic and time-consuming, since the developers often do not fully reflect the instructions for replacing the fishing line in the operating manual.

How to wind the line on a lawn mower. How to wind the line correctly on the trimmer spool

Many, having worked out the factory line on the recently purchased trimmers, are trying to wind a new one, but they cannot, because they do not know how to properly wind the line on the spool (bobbin) of the trimmer. It seems that there is an instruction, but it still does not work. Let’s try in this article to deal with this issue.

So, in order to wind the line, you first need to remove the coil from the trimmer. this will be more convenient. The removal method will depend on the type of trimmer.

Winding process

If your coil is designed to work with only one tendril, then it’s simple. You need to unwind 2-4 m of fishing line (depending on the size of the reel), find a hole on the inside of the reel for the fixing line, insert one end of the line there and start winding the line in the direction opposite to the direction of rotation of the reel on the trimmer. On the inside of the reel, they usually indicate with an arrow in which direction to wind the line. I wound the fishing line, we leave a small piece of it unwound to put it out. We fix this piece in a specially groove located on the inner part of the reel and designed so that at the time of collecting the reel, the line does NOT unwind. If there is such a groove, then you will have to hold the fishing line with your finger to prevent it from unwinding during the further collection of the coil. Next, we take the outer part of the coil and threading the outer piece of fishing line into the existing hole, collect and put the coil back on the trimmer.

If the coil is designed to work with two tendrils, then do the following. On the inside of the reel, we look at how many grooves there are for winding the fishing line. There may be one or two of them. If there is only one groove, then both tendrils are wound along this one groove. If there are two grooves, then each antenna is wound along its own groove. Reels with one groove should have a through hole through which the fishing line is threaded. We rewind 2-4 m of fishing line, threading it through this hole so that the fishing line sticks out equally on each side. And we simultaneously wind both tendrils of the fishing line in one direction, opposite to the direction of rotation of the coil to the trim tabs and coinciding with the direction indicated by the arrow on the inside of the coil. We leave a little of the fishing line unwound, the resulting ends We fix in the Special grooves, and if they are not there, we hold them with our fingers. Threading both ends into the existing holes on the outer casing of the coil. We collect the coil and fasten it to the trimmers.

If there are two grooves, fold a piece of fishing line 2-4 m long in half. Insert the loop obtained at the place of the fold into the groove between the two grooves, and simultaneously wind both ends of the fishing line along its own groove. Further actions are similar to the previous option.

There are also spools in which the fishing line is threaded through a through hole on the inside. After that, the ends of the line, and not winding, are threaded completely through the holes on the outer body of the reel, assemble the reel and begin to rotate the button, which is usually pressed, in order to release the line during operation as it wears out. Turning the button. the line itself is wound inside. In this case, twisting it in the “wrong” direction will NOT work, since it can only rotate in one direction. If you get used to it, you can wind fishing line on such a reel without even disassembling it. you just need to combine the through hole of the inner drum with the holes on the outer body of the reel, and then thread the fishing line through them.

That’s all on this issue. Happy winding!

Trimmer head with two tendrils

Double flute head

After removing the spool from the spool body, we determine the number of strands for winding the line (1 or 2). In principle, there is no difference between bobbins with one and two grooves, but with careless threading into the paired groove, there will be operational problems. Due to the likelihood of interlacing the adjacent line of the tool, a situation may arise when, after wear of the working antennae, it is impossible to remove new ones.

Regardless of the number of streams, a fishing line with a length of 1.5 to 3 meters is taken for refueling. Winding must be done in the opposite direction of rotation of the head, since winding in the direction of travel will lead to the fact that the line will not be removed from the reel. After the fishing line is tucked into the trimmer coil, the free ends (15-30 cm) are threaded into special holes. Next, we assemble the head in the reverse order of disassembly and check the operability. Do NOT worry if the ends of the two antennae are very different in size, because when you start the trimmer, the knife installed on the protection will cut off excess.

In the model with one groove

The line must be pulled through the hole, and its mustache must be folded together and aligned.

Then winding is performed in the opposite direction to the rotation of the bobbin on the mower. Often there is an arrow inside the spool indicating how to put on the line correctly.

The ends of the string are fixed in special grooves or simply temporarily held by hands and pulled into the hole located on the outside of the bobbin.

After that, the spool is closed and attached to the rod, after which the mower is ready to work.

Mower device

In trimmers, the element on which the string is pulled is very simple. It is called the “coil”. Usually it consists of an upper and a lower part (grooves), between which the partition passes from the recess. It is on these grooves that the fishing line should be wound. However, first it is pulled through the recess.

Before pulling out the coil, Unscrew the special button located directly on the mower body. Remove the reel from the mower before changing the line.

It is not difficult to do this, but there are some peculiarities depending on the trimmer configuration and the coil itself.

In small electronic mowers, the motor and reel are at the bottom, and buttons are located on the sides of the reel. If you press them, you get the upper groove of the reel and the part where you need to wind the fishing line.

In a mower with a curved bar, which does not have a knife, the spools have special two-horned nuts. In such tools, it is necessary to hold the bobbin so that it does not move, and at the same time it does not turn the nut clockwise. It is she who holds the entire bobbins, which is then easy to remove.

Straight boom mowers that can be fitted with a knife have a hole just below the reel. To remove the coil, a screwdriver is inserted into this hole, while the bobbin is fixed. After that, the coil must be turned clockwise and removed from the unit.

Sometimes there may be latches on the coil. They must be pressed to Disconnect the coil parts. It is also possible that the top and bottom of the bobbin are connected by a thread. In this case, it is enough to grasp the top and bottom with your hands, and then twist in different directions until they do not unscrew.

How to choose the right line?

Nylon lines are suitable for both electric and gas powered trimmers. This consumable can be used for both hand tools and a wheeled lawnmower. It is important to choose the right line, as this directly affects both the result of the work and the service life of the unit. Of course, it is very easy to get confused in the offered assortment of lines, especially for beginners. However, there is a lot of advice from experts and those who have already tried various options.

For an electric trimmer less than 500 W, a thin line with a diameter of 1 to 1.6 mm is suitable. She will perfectly cut lawns with low grass. If the power of the tool is in the range from 0.5 to 1 kW, then it is better to give preference to a line with a diameter of 2 mm or slightly more.

For petrol trimmers and lawn mowers, line less than 3 mm must not be taken. This thickness will allow you to easily cope with any weeds, dry stems, dense grass. Diameter over 4 mm is only suitable for high power lawn mowers. It turns out that thick line is necessary for powerful technique. It is not recommended for use with low power trimmers, otherwise it will not work well, constantly winding around the reel and creating additional load on the engine.

Typically, a standard package contains up to 15 meters of line. However, to replace the string on a reel, a length of about 7 meters is sufficient. It also happens that the line is produced in bays of 250-500 meters. When choosing a string, it is imperative to specify the date when it was produced. Too old nylon can dry out and the floor is too brittle. If this happens, then you can soak the fishing line for a couple of hours in water, but it will not be completely the same.

When choosing, an important parameter is the section of the string, which can be of several types.

The round section is versatile. It is used for mowing grass of medium thickness and density. May make excessive noise during operation, but is NOT used too quickly.

A square or polygonal section is more efficient than a round one. Sharp corners cut plant stems faster and with better quality.

Ribbed, Vito and Star-shaped are the most effective. Such a fishing line manages to mow the grass very quickly. And its main disadvantage is its rapid wear.

The trimmer line is made of nylon, which is durable, lightweight, low cost and durable. To make the cost of the material even cheaper, polyethylene is added to it, but then the line overheats faster. Thick strings have a graphite or steel rod. Sometimes they are reinforced, which increases strength and service life.

Version with two grooves

The line is first folded in half to determine where the middle of the fold is.

Further, the loop formed on the bend is threaded into the groove, which is formed between two grooves.

After that, you can wind both bars of the line in a separate groove.

You can fix the mustache and assemble the coil completely in the same way as described above.

Opening a reel for the first time and winding a new line is not always easy. Over time, this procedure becomes almost automatic and will NOT take much time. Some reels have an automatic system that spins the line by itself. In total, it remains only to correctly set the end of the line, and everything is ready. In such models, the string must be put in the hole that is on the outside of the body. Next, the bobbin is assembled, and when the winding rotates, the fishing line is put on it.

Lawnmower fishing line: how to choose and wind?

With the arrival of spring, summer cottages become the main residence of many of our compatriots. However, with the arrival of warm days, there is such a problem as fast-growing grass. It is inconvenient to constantly mow it with a hand scythe, and not all types of grass lend themselves to this old working tool. It is much more convenient to use modern lawn mowers for THESE purposes. Particularly popular among them are devices with a line, which is easy to change if necessary.

How to reel?

Knowing how the reel is disassembled can speed up the line change process. It all depends on what design the coil has and how many antennae. Threading a spool with only one working mustache is quite easy, especially if you stick to a consistent plan.

Depending on the parameters of the reel and the length of the line set initially, it is recommended to choose a string from 2 to 5 meters.

First you need to remove the bobbin from the tool, and then open it.

One of the ends of the line must be installed in the hole inside the spool.

Next, the string should be screwed onto the drum. And this is done in the opposite direction from the normal rotation of the spool. Usually there is an arrow on the trimmer on the inside of the bobbin, which shows in which direction to wind.

Part of the line must be pulled out and fixed in a special groove located on the inside of the reel. Its purpose is to hold the winding while bringing the bobbin into working condition.

The end of the string must be passed through the hole on the outside of the bobbin.

At the last stage, you need to collect the parts of the bobbin and put it on the mower bar.

Installing the fishing line on a reel with two mustaches occurs in a somewhat second way. First, you need to determine how many grooves go along the inside of the reel on which the line is put. There are options with one groove, and then both mustaches must be wound together. There are also models with two grooves, when each of the mustache goes separately.

Safety engineering

Compliance with safety precautions will allow you to quickly and safely insert new line into the reel on the mower. It is imperative that before the replacement begins and the coil is removed, the device must be turned off, especially for electric lawn mowers. It is important to constantly remind yourself to press the special lock button. On each mower, it can be located in different places, but this must be indicated in the operating manual.

Remember to adjust the cutting element. Otherwise, the work will be unstable and of poor quality. Most often, there is a button on the unit itself that allows you to configure this. If nothing happens when you press it, or the string has loosened its tension, then you need to hold down the button and pull the line out of the reel with effort.

Line winding is a very demanding process. It is important to follow all the steps correctly in order to pull the line well. Materials other than special nylon strings should not be used. It is worth remembering that you cannot put a metal wire, a rod or an iron cable instead of a fishing line. This is dangerous, as the rig can very easily cut through shoes made of even coarse material and injure the wearer. Before putting on a new line, it is important to carefully read the operating instructions for the device, since some models of lawn mowers may have their own structural features, which are important to take into account when replacing.

You can find out how to replace the line with a trimmer from below.