Advantages and disadvantages
There is little to say about the strengths of the petrol trimmers mentioned by the manufacturer. The main ones are the following:
- The presence of a two-stroke engine with a capacity of just over 3 horsepower, which is air-cooled and electric ignition;
- The tank is made of translucent plastic, which allows you to know exactly how much fuel was consumed during operation;
- The ability for a person to work comfortably. This is achieved due to the presence of an ergonomic bicycle-type handle and a special mechanism for damping various kinds of vibrations;
- It uses a high-quality cutting set in the form of a cutting knife and a high strength fishing line;
- Here, too, a wide delight applies to mowing. 25.5 centimeters, which makes it possible to effectively and quickly mow grass, shoots and other greenery
- A protective casing that protects a person from falling grass, stones and various debris;
- Shoulder strap, which allows the operator to work for a long time and NOT feel tired;
- Ease of maintenance and operation. The principle of operation and the device of models from Huter are very simple, which will make it easy to deal with their implementation even for an ignorant person;
- Reliability. Such a gasoline trimmer can work for a long period of time without stopping, while it does not heat up due to the peculiarities of the air cooling system;
- The ability to move freely around the site. Considering that petrol trimmers, unlike electric ones, do NOT depend at all on the presence of an outlet, which guarantees a person freedom of movement.
At the same time, there are a number of disadvantages, in which it is impossible not to mention, namely:
- Noise during operation. Gasoline trimmers Not only from Huter, but in general they vibrate quite a lot and make a lot of noise, which creates uncomfortable working conditions;
- Pollution of nature. Fuel-powered models generate various types of exhaust gases during operation, which are harmful to the environment;
- High price. Trimmers of the described type have a high cost due to the fact that they have high performance and good technical characteristics.
If we talk about the features of the models of this manufacturer, then first it should be said that this company from Germany was founded in 1979. All equipment produced under this trademark is created by qualified engineers and developers and is tested at every stage of creation. In general, the lawn mowers of this German company are powerful and quite productive models. Their use makes it possible to shear the grass literally in any conditions. Very often the best models of this company are used for professional purposes. One of the main features common to all models of the manufacturer is that Huter lawn mowers are equipped with an air-cooled two-stroke engine and electronic ignition. This option makes it possible to provide high power of the device and high-quality performance of the task.
If we talk about the most popular models of this German company, then you should first call the GGT 2500S. This equipment is considered one of the most productive models and has excellent technical characteristics. Its use makes it possible to process large areas and use it both in everyday life and for professional purposes. Its features are as follows:
- Air-cooled two-stroke engine;
- Electronic ignition;
- Power. 2.5 kW;
- Has a vibration suppression mechanism;
- Can bevel 25.5 centimeters wide.
Another interesting model that may be of interest to many. GGT 1000S. It can be used for professional purposes. It has such main features as:
- Two-stroke motor, as in the previous model;
- Electronic ignition;
- Performance. About 1000 W
- Can bevel 25.5 cm wide;
- Her turnovers. Up to 9.5 thousand per minute.
The GGT 1300S will also be of interest to many as it is a powerful and productive trimmer that can handle all types of vegetation. It is equipped with a vibration damping mechanism, as well as a lock key and a lock for the gas pressure handle. It has the same features as the previous models, except that the power is higher here. 1300 Wt.
Another petrol trimmer from Huter that deserves attention. GGT 1500T. The high power allows you to carry out almost any task. The model operates on one of the most powerful engine models, which allows for simple cutting of literally any thickets, young growth of trees, as well as thick weeds. It has an anti-vibration mechanism, a convenient shoulder strap, and a manual start mechanism. This model differs from the previous ones by the presence of a more efficient 1500 W motor model, as well as by the fact that it emits less noise.
The last model I want to say. GGT 1900S. It is the second most powerful in the line of this manufacturer with an indicator of 1900 watts. The engine installed here was specially designed for the GGT 1900S. Its other features are the presence of an anti-vibration mechanism, as well as the ability to adjust the position of the handle for a more comfortable grip. In addition, a special protective cover is included in the package.
Before using the petrol trimmer, owners must ensure that the gearbox is lubricated. In addition, in order to use this device correctly, you should read all the norms that the instruction manual contains. It also contains safety standards, advice on skills and techniques for effective work, as well as the correct maintenance of lawn mowers.
When the user is familiar with all this, he can start the lawn mower and start running in the device. It should be carried out within the first 3-4 hours of operation. The lawnmower should be used very carefully during this time. This is best done sparingly on soft grass. In no case should it be used in idle mode for more than 10 minutes. These periods should be necessarily alternated with breaks and a blow-by of 20-30 seconds. During this period, the adjustment and adjustment of the operating modes of the gasoline trimmer is also carried out. It will not be superfluous to have a spare line, so that in case of damage or unsatisfactory work of the standard line, you can change the line to a better one.
Gasoline trimmers Huter: types and subtleties of operation
Cleaning a personal plot or adjoining territory is a very important component, which gives a certain place, be it a summer cottage or the territory of a multi-storey building, a pleasant appearance and flavor. For a long time now, classic braids are NOT considered effective. They were replaced by such a thing as a lawn mower or as it is also called a lawn mower. Such a petrol trimmer. An efficient device that allows you to mow the grass quickly and easily. If we talk about the best solutions for grass, then the models produced by the manufacturer Huter are considered by consumers to be of the highest quality.
Petrol trimmer. A technically complex device. Before implementation, you should read the instruction manual very carefully. But this is often neglected, due to which the product can quickly fail. As a result, it stalls, heats up too much and fails. Or it simply does not start due to the fact that a person has NOT read the operating rules, and fills it with low-quality gasoline.
For an overview of the Huter GGT 1900T petrol trimmer, see the following.
Petrol Trimmer Won’t Start? Elitech T750 Reasons and Solutions
In general, such a conversation should start with the fact that after buying a garden gasoline tool, it would be better to first familiarize yourself with the instructions attached to it. Then many problems could be avoided. But since this happened, the gasoline trimmer does not start, then you need to look for sources of inoperability. And in this article we will consider the main reasons why the trimmer does not start on the example of the Elitech T750 model, as well as we will tell you general recommendations for using such a tool.
You should start with the banal! Let’s figure out how to properly start a gasoline trimmer. It may be that the reason lies precisely here.
First you need to bring the red toggle switch on the trim bar to the “I” position. This means turning on the power. Then you need to switch the fuel supply lever to the carburetor and use the fuel “suction” button (similar to a pipette, located in the carburetor). This is necessary to supply gasoline to the engine. Return the fuel delivery lever to its original position. Finally, pull the starter handle sharply towards you. The trimmer should work. Try it several times if it doesn’t work the first time. If, after such manipulations, the situation has risen and the gasoline trimmer does NOT start, then you should first inspect it yourself before you take it to the service center. There are two main reasons your garden trimmer won’t start:
- Power circuit breakdown.
- Sun fuel.
- Let’s start with the ignition problems. In most cases, it is caused by the need to change the spark plug in the engine. This is done like this:
- First of all, we have to take care of the safety measures, making sure the trimmer is disabled. We bring the above toggle switch to the “STOP” position.
- Then we remove the rubber protection from the candle and the wiring terminals. Using a special spark plug wrench, we unscrew the spark plug and replace it.
- After that, we assemble the device and carry out the above procedure for starting the trimmer.
The second reason a garden tool doesn’t work. Out of fuel. On the Elinech T750, the fuel tank is located near the engine, but on most trimmers it is located there. We unscrew the cap from the tank and fill it with gasoline (the most optimal version is AI-92, it is inexpensive and does NOT clog the carburetor like the AI-76). Do not forget to add special oil for engines to the tank, 50 grams is enough for the gas tank, without it the engine will start to “sneeze” and will quickly become unusable. Then we close the tank with a cap, wipe the trimmer surface and our hands with a dry cloth. We also do the above manipulations to turn on the garden tool.
If the petrol trimmer does not start as before, then it makes sense to have it repaired. And the reason for this decision is simple. If you DO NOT have the appropriate skills, it is almost impossible to repair equipment.
In order for the tool to serve as long as possible and NOT to have such problems, you should first of all read the instruction manual for the trimmer. Also pay special attention to the engine running time in the trim tab. Take a short break every 15 minutes of work and, finally, take proper care of the tool, wipe it after work, grease it with graphite grease. Observing such simple rules, you can significantly increase the service life of the tool and it is quite possible that you DO NOT have to look for reasons why the gasoline trimmer does not start.
36,743 total views, 3 views today
Breather. This is a check valve designed to equalize the pressure in the gas tank. If it is clogged and does NOT allow air to pass towards the tank, then a vacuum will form inside the fuel container and the fuel will no longer flow into the carburetor. To check if the valve is working, remove the hose that goes from the reservoir to the carburetor. If gas does NOT flow out of the tank, then the breather is clogged.
Trimmer users often ask themselves: Where is the breather? This valve is usually located in the gas cap and looks like the following figure.
Cleaning the breather is very simple: Let’s disassemble the valve and rinse all its components. On some lawn mowers, this valve may be located directly on the fuel tank. You will NOT be able to find it right away, since it is hidden from view under the starter housing. Such a breather is cleaned with a regular needle.
Fuel tank (fuel quality)
Remember that it is always necessary to check the availability and quality of fuel before starting the unit. In this case, you should not be greedy and save, and also “be smart” about the amount of added oil. Everything must be done according to the manual attached to the device, since if the piston group fails, its replacement will cost about 70% of the total cost of the trimmer. Fill up with fuel assuming that you completely use it up when performing work. Gasoline remaining in the tank loses its properties after a while and can harm the engine. Therefore, the mixture is not ready for future use and in large quantities. If the lawn mower does not start well, try draining “old” fuel from the tank, and fill it with a freshly prepared mixture.
Breakage of petrol trimmers
Typical breakdowns of a gasoline trimmer, which the owners of this unit most often encounter, are as follows:
- Engine breakdown;
- Carburetor problems;
- Fuel supply problems;
- Muffler malfunction;
- Gearbox breakage;
- The starter has broken;
- Air filter problems;
- Gas tank breather clogged.
Why Petrol Trimmer Won’t Start
The reasons why the petrol trimmer stopped starting may be different, so a step-by-step diagnosis of the device is required.
This filter cleans the fuel from possible contamination. If it is clogged, then gasoline does NOT enter the cylinder, and, accordingly, the unit does not work or stalls after starting. The fuel filter is located at the end of the intake hose inside the fuel tank. To get to the filter, you need to remove the plug with the tubes coming out of it.
When removing the plug, the suction hose may come off and remain in the reservoir. It is removed with tweezers.
Next, remove the old fuel filter from the hose and replace it with a new one purchased in advance. You can also clean the fuel filter if you have a new one. The filter must be secured to the hose with a spring clip.
Install the intake tube on the plug and insert the last into the tank.
Candle and candle channel
So, you changed the fuel, but nothing has changed, and the trimmer will still Won’t start. In this case, it is worth checking the candle channel to see if it is throwing a combustible mixture over it. Often, users move the air damper to position “OFF” when starting, and when the engine is started, and do not move it to the position “ON”, after which it stalls. Further, an attempt to restart the internal combustion engine leads to the fact that gasoline fills the candle, and the start becomes impossible. To diagnose and fix a possible problem in this node, do the following.
- It is necessary to Unscrew the spark plug, wipe it well and dry it. When installing the spark plug into the internal combustion engine cylinder, it must be dry.
- Drain the accumulated fuel from the combustion chamber. This is done through the hole from which you unscrewed the candle.
- If there is soot on the electrode of the candle, it must be removed either with a thin file or with a nail file.
- Do not forget to set the gap between its electrodes before installing the part. The gap on the spark plug should be 1 mm. You can use a coin as a probe to check the gap.
- Next, Assemble the unit, read the starting instructions and try to start the engine again.
If the GIS does not start, then you need to check the Spark. For this:
- Unscrew the candle;
- Put a cap of a high-voltage wire on it;
- Touch its metal part to the cylinder body (to ensure contact, you can insert a pipe wrench) as shown in the figure below;
- Pull the starter cord so that several engine revolutions occur.
Normally, with each piston weft, a spark should slip between the electrodes of the plug. If there is a spark, then the reason that the GIS does not start should be looked for in other nodes of the device.
For a better understanding of the process, how to test a candle for the presence of a spark, you can use this, where the test is shown using the example of a lawn mower. “Union”.
If there is no spark, then first check the cable connecting the spark plug to the coil. Perhaps the reason is in him. You can call him using a tester. If an open circuit is detected, the high-voltage wire will need to be replaced.
Also, a prerequisite for the missing spark may be a malfunction of the ignition coil (Magneto). The picture below shows what the coil (magneto) looks like from a Patriot petrol trimmer (Patriot).
To exclude a malfunction, you will need to check the trimmer magneto with a tester, namely, its primary and secondary windings. On the primary winding, the resistance should be between 0.4 and 2.0 ohms. If the device shows 0. This means that a short circuit has occurred in the winding, and if infinity. This is a clear sign of an open circuit. The resistance on the secondary winding must be between 6 and 8 kΩ.
Model operating instructions
The above-described petrol “bellows” trimmer should be used taking into account the safety rules, which are spelled out in the instructions. From them you will be able to find out that it is unacceptable to use the equipment by persons who are under the influence of AL-Kogol or physically tired. Before starting work, you must equip yourself with special protective equipment, among them appropriate clothing, goggles, mittens or gloves, a helmet and headphones should be distinguished. The equipment must not be used in the vicinity of flammable and explosive substances. This also applies to conditions under which high humidity remains.
The cost of spare parts for a trimmer
Regardless of the quality of the tool, you may need spare parts for the “bellows” trimmer. Some of them will be discussed below. For example, a clutch drum with a housing will cost the consumer 860 rubles, while the clutch housing mounting bolt costs only 5 rubles. A flexible shaft for a trimmer costs 600 rubles, but a container for preparing a fuel mixture will cost a symbolic amount. 50 rbl.
Need a trimmer
Reviews of electric trimmers brand GET 1200SL
If you want to buy an electric fur trimmer, then you can pay attention to the model that was mentioned in the subheadings. Its cost is NOT so high and amounts to 5000 rubles. The equipment, according to buyers, can be used for treating a lawn in a personal plot, as well as treating small areas. You can use the tool to cut grass even in hard-to-reach places such as along a fence or under a bench.
The power of the unit is sufficient to perform tasks in everyday life and is 1.2 kW. The bar is collapsible, this, as buyers emphasize, simplifies not only storage, but also transportation. This example is an ideal solution for women and elderly people, because the equipment is lightweight. Weight is 4.5 kg.
A lawn is quite an attractive element of the site today. However, it will look good if you take care of it. To do this, water the area regularly, feed it with fertilizers and cut the grass weekly. If you neglect the last condition, then rather quickly the territory will turn into dense thickets.