Into the tree
As for the tree, everything is very simple here. The only restrictions may be imposed by the type of wood used. If it is soft, you do not need to pre-drill the hole. If the workpiece is made of chipboard or fiberboard, then it is better to drill a hole. Moreover, it is recommended to drill a hole in cases where it is necessary to tighten a long self-tapping screw on wood. This applies even to soft wood..
When making a hole, its diameter should be smaller than that of a self-tapping screw. This will ensure reliable fastening of the workpieces..
In addition, the hole should be made even in cases where the wood workpiece is relatively thin and there is a risk of splitting. When screwing the self-tapping screw into such parts, you need to be careful.
When screwing in, the cap should sink into the wood. If this is a finished floor, then all holes must be covered with wood putty..
Into metal
As for screwing the self-tapping screw into metal, only fasteners for metal are used here. The screwing method depends on the thickness of the workpiece. If this is a thin sheet, then it is often possible to tighten it without much effort using a screwdriver or screwdriver. Moreover, there are different types of self-tapping screws. Some have a small drill on the tip with sharpened teeth, as shown in the picture.
Self-tapping screw with a drill in sharpened teeth
But as practice shows, not all such self-tapping screws can be screwed into metal, this is due to the weak sharpening of the drill. So, a screwdriver is used to tighten them. You should not gain high speed, otherwise the self-tapping screw may overheat and quickly become dull. These fasteners can be used for metal up to 7 mm thick..
If the metal is too thick, then the best option would be to pre-drill the hole with a drill / drill, and then screw the fasteners into it. This method is not associated with any problems..
When making a hole, remember that it should be smaller in diameter than a self-tapping screw. When the hole is ready, it can be lubricated with machine oil. This will allow you to tighten the self-tapping screw without much difficulty..
The self-tapping screw used for metal must be made of solid steel, which is harder than the product.
How to screw a self-tapping screw into various materials: important nuances of a seemingly trifling matter
Self-tapping screws are a very common product widely used for various types of fasteners. However, in order for its capabilities to be used to the maximum and in order for the fastening made with its help to have maximum reliability, it is necessary to be able to correctly select and screw the self-tapping screw into the bearing surface. We intend to pay close attention to these issues today..
General screw-in technology
Use an awl to make a small indentation in the place reserved for the self-tapping screw. Install the product “on position”. Use careful but firm movements to rotate the part until it deeply deepens and locks in the material. Then the force can be increased. Towards the end of the “process”, the speed must be reduced again – so as not to damage the screw.
Furniture or confirmation
This type of self-tapping screw requires pre-drilling a hole in the piece of furniture. A hex wrench is used to tighten it..
These are perhaps the most common types of self-tapping screws that are used in various fields of construction. Let’s take a look at the details of how to screw this or that self-tapping screw into different surfaces..
Concrete
Perhaps, the method of installation in concrete is now known to everyone: first you need to install a dowel in it, and then you need to screw the self-tapping screw itself into this already installed dowel. According to many craftsmen, the reliability of fixation increases significantly if the surface of the dowel is lubricated with the appropriate glue..
For drilling holes, it is best to use a hammer drill, the selection rules for which we have already written about. By installing self-tapping screws on dowels, you can use both universal products and wood.
How to properly screw a self-tapping screw into various materials
Self-tapping tools
Fasteners can have caps of different sizes and recesses in them of various shapes and sizes. Therefore, before screwing in the self-tapping screw, make sure that you have a screwdriver or screwdriver with a suitable attachment in your arsenal. In general, it is better to have nozzles for the corresponding tools, as they say, to the maximum. Plus, they should be replaced regularly, since the wear of the devices during operation cannot be avoided..
Note! The best bits are those made of tool steel with hardening additives. Do not stop your choice on the first set that comes across, otherwise after a couple of days of intensive work you will have to go for a new one..
If you plan to screw one or two self-tapping screws into an unstable surface, then you can work with a screwdriver. If it is more, you cannot do without a screwdriver. Tightening fasteners with a screwdriver is not as easy as it might seem at first glance, and requires some skill. A screwdriver will do everything quickly and efficiently.
How to replace a screwdriver with a conventional drill: 3 useful tips
Ingenuity helps to get out of difficult situations associated with a lack of tools. A drill can replace a screwdriver. Knowledge and adherence to safety rules is the first condition for working with this tool. Therefore, to the question “is it possible to make a screwdriver out of a drill?” there will be a positive answer. We will talk about the intricacies and secrets of the process in the article.
Which is better a drill or screwdriver?
The principle of operation of a drill and a screwdriver is similar. The devices differ from each other in that the first tool is equipped with a limiter for the rotation of the chuck when the resistance reaches its highest point. If you tighten the screws with a drill, it is important not to miss this moment. then the surface will not be damaged, and the corners of the bolt will not be smoothed (this will significantly reduce the adhesion of the surfaces).
The drill is designed for drilling holes, and the screwdriver is for screwing in self-tapping screws, but they can be replaced with one another. There are drill bits that turn it into a screwdriver. Nozzles are:
- simple;
- with limiter.
The stop does not allow the self-tapping screw to enter too deep into the surface. This effect is provided by the restrictive rim present on the nozzle..
It is impossible to say which is preferable – a drill or screwdriver – since the two tools perform different functions.
Using a drill as a screwdriver
In the absence of attachments (and the ability to purchase them), it is recommended to use the following strategy. There is no splitting sleeve in the drill, which leads to unpleasant consequences. Using this tool as a screwdriver without the necessary attachment can be fraught with:
- breakage of the screw head;
- broken bit;
- by the combustion of the drill.
Tighten screws or bolts with a drill not to the bitter end, but leave at least half a centimeter outside the surface. It is generally optimal to screw the rest of the screw into the surface by hand. Yes, you will waste time, but keep the drill safe.
The drill can also be used for its intended purpose (drilling surfaces). Drill a hole in the surface of the material to be used, then carefully screw in the screw. This will be much faster than screwing in the screw by hand. In addition, you will definitely not damage the surface, creating a more delicate mount without delamination of the material. Useful if you need to drive a screw into wood.
Is it realistic to tighten screws with a drill? You can, but do not lose sight of one feature of the screwdriver. This is a kind of symbiosis of a Phillips screwdriver and a drill. A tool with speed control will be especially appropriate. The slower it runs, the less risk of failure. With skill and a good reaction, furniture assembly (and other construction work) will go even faster with a drill..
Based on the above information, it can be concluded that there are three ways to get a high-quality result when using a drill instead of a screwdriver:
Use special nozzles with a limiting rim;
Do not screw the screws into the surface completely, making the last few turns by hand;
Drill the surface in advance, and then screw the bolts into the hole made.
Just always be careful and follow safety precautions when working with tools..
Watch the video: How to use a drill instead of a screwdriver?
How to plant drywall on self-tapping screws
- How to plant drywall on self-tapping screws
- How to fix drywall
- How to fix drywall
In the process of fixing drywall, the choice of quality hardware and certain tools takes an important place. As a rule, special self-tapping screws are used, which are tightened with screwdrivers, a drill or a screwdriver.
It is very important to correctly select drywall fasteners before starting work. Certain rules will help here, among which two main ones can be distinguished. The length of the hardware should be about 10 mm more than the profile thickness. In other words, if the work is done with the material of the parameter 12 mm, the self-tapping screw will need to be taken at least 20-25 mm in length. If the installation of two layers of material is carried out, the fasteners are selected in 35 mm. When answering the question of how to use self-tapping screws when working with drywall, it can be noted that it is very important to select such devices that will correspond to the material.
In the process of fastening, it is very important not to overdo it and not to twist the self-tapping screw, as there may be a risk of rupture of the drywall layer. This can cause a not tight connection of sheets, therefore, the rigidity of the frame cannot be achieved, and in fact, this is the main function of any structure. Incomplete twisting is also highly undesirable, since bumps can be found during the filling process. If you clean these errors with a piece of sandpaper, all this will lead to the formation of red spots over time. The best option would be to screw the self-tapping screws to a depth of 1 mm from the top of the material surface to the fasteners. It is this distance that will provide an opportunity to maintain the integrity of the drywall, and the layers will ideally be attracted to each other..
In a situation where it is required to fix several sheets of material at once, the step of fasteners in the process of joining the first layer can be allowed to be 60 or 70 cm, when attaching the very last layer, it should be equal to 30-40 cm.In case the sheets of material stand side by side , the hardware is screwed in with a slight offset, the distance is maintained at 5-7 cm.It is important to pay attention to this parameter from the edge of the material, here it is worth keeping 10 mm, not closer.
In the process of installing drywall, it is important to carefully ensure that its sheets are arranged strictly in a checkerboard pattern. This will give the entire structure as a whole optimal rigidity, and will also reduce the likelihood of destructive cracks. If you follow all of the above tips, you can have no doubt about the quality of the resulting structure..
Types of self-tapping screws
There are two main types of self-tapping screws used for self-repair – for wood and universal. Their main difference is in the thread pitch – “screws” for wood are characterized by a large pitch (less frequent threading).
There is a misconception that universal parts are just as good for wood, plywood and chipboard as specialized ones. No, of course, it will not be difficult to screw them into these materials, but how well they will stick there is a big question. The fact is that the “raw material” into which the self-tapping screw is “immersed” must reliably lie in the grooves of the thread, and the structure of the wood will not allow it to fit qualitatively in the narrow “grooves” of the universal self-tapping screw.
General screw-in technology
Use an awl to make a small indentation in the place reserved for the self-tapping screw. Install the product “on position”. Use careful but firm movements to rotate the part until it deeply deepens and locks in the material. Then the force can be increased. Towards the end of the “process”, the speed must be reduced again – so as not to damage the screw.
Table of contents
- Types of self-tapping screws
- Self-tapping tools
- General screw-in technology
- How to screw screws into different materials?
- How to properly tighten the unscrewed self-tapping screw?
Tools
The thing is that home craftsmen often do not know how to screw in a self-tapping screw correctly and how to choose it correctly in general..
Self-tapping tools
Fasteners can have caps of different sizes and recesses in them of various shapes and sizes. Therefore, before screwing in the self-tapping screw, make sure that you have a screwdriver or screwdriver with a suitable attachment in your arsenal. In general, it is better to have nozzles for the corresponding tools, as they say, to the maximum. Plus, they should be replaced regularly, since the wear of the devices during operation cannot be avoided..
Note! The best bits are those made of tool steel with hardening additives. Do not stop your choice on the first set that comes across, otherwise after a couple of days of intensive work you will have to go for a new one..
If you plan to screw one or two self-tapping screws into an unstable surface, then you can work with a screwdriver. If it is more, you cannot do without a screwdriver. Tightening fasteners with a screwdriver is not as easy as it might seem at first glance, and requires some skill. A screwdriver will do everything quickly and efficiently.
How to screw screws into different materials?
Many men, not knowing how to screw a self-tapping screw into concrete, spoil a sufficient number of purchased parts. In fact, everything is quite simple: self-tapping screws are “integrated” into concrete with the help of dowels – strong plastic “tubes”. First, a hole is made in the material, a dowel is installed there, which “receives” the fastener.
Worth knowing! Craftsmen advise to grease the dowels with glue before installing. This, in their opinion, strengthens the connections..
Drilling holes in concrete should be done exclusively with a hammer drill – even a hammer drill may not withstand, let alone a conventional one. Self-tapping screws are suitable for both wood and universal.
Brick, ceramic tile, screed
Self-tapping screws are screwed into these environments in the same way as into concrete. The only thing is, for working with tiles, it is better to take an ordinary drill, since it can crack from the excessive power of the hammer drill..
Copper, bronze, aluminum
Measure the shank diameter of the fastener excluding threads. This manipulation must be performed with a caliper. Install pointed jaws perpendicular to the self-tapping screw and clamp the product so that they completely penetrate into the thread groove; determine the diameter. With a drill with a diameter of one and a half millimeters smaller than the obtained value, make a hole in the material. Screw the self-tapping screw into the hole – and the job is done. Use parts with a universal thread..
Note! Before “piercing” the main structure, it is recommended to check the drill on a small unnecessary piece of similar material. Drill a hole and try to screw the product there. The drill is considered correctly selected if the self-tapping screw goes into the hole tight enough, but does not jam. In the event that the screw fails to “break through”, you should work with a thicker drill. Too light twisting of the part symbolizes that you need to take a thinner drill – otherwise the self-tapping screw may pop out at any time.
The hole in the material must be equal to or slightly larger than the unthreaded bar diameter. Self-tapping screws will not be able to cope with a number of hard metals – in particular, it is almost impossible to screw these fasteners into cast iron.
Not every plastic is ready to accept a self-tapping screw, so it will not be superfluous to make sure before starting work that the material exactly fits. The technology for screwing a self-tapping screw into plastic is the same as for soft metals – copper, aluminum, bronze. Featured Products – Wood Carved.
Wood, fiberboard and chipboard
Don’t know how to screw a self-tapping screw into the board? Believe me, nothing is easier. The basic rule is to use only wood screws. For hard types of wood, thin boards, chipboard, fiberboard, preliminary drilling of a hole for the product is mandatory, since there is a risk of splitting the material with a self-tapping screw. For thick softwood boards, this manipulation can be dispensed with..
If you are working:
- with hard wood. choose a drill with a diameter equal to the diameter of the self-tapping rod (naturally, no thread);
- with fiberboard – 1 millimeter less;
- with chipboard or softwood – 2-3 millimeters less.
Mark points on the sheet with a pencil. The optimal pitch between the screws is up to 70 centimeters, depending on the expected loads on the structure. If you are using a screwdriver, you can start screwing the product at maximum speed. After the self-tapping screw enters the surface by ½ it is recommended to gradually reduce the speed to the minimum. When tightening with an ordinary screwdriver, all movements should be smooth. It is very important to tighten the self-tapping screw correctly – ideally, it should be 1 millimeter below the level of the cardboard, not gypsum! This will ensure the maximum strength of the future structure. If you suddenly did not follow the technology and broke through the cardboard, the “ill-fated” place needs to be putty, and a new fastener should be placed at a distance of 5-9 centimeters from it.
The type of self-tapping screws for drywall must be selected depending on the material used in the construction of the sheathing. For the metal frame, universal or metal self-tapping screws are required, for wooden lathing – wood products.
How to properly tighten the unscrewed self-tapping screw?
The unscrewed part must be re-tightened exactly as it stood before. It is very important that the screw goes into the same groove, at the same angle. If the product “draws” a “new path” for itself, the reliability of the fastening will be significantly reduced. How to get into an existing cut? Just insert the part into the hole and turn it by hand without pressure. As soon as everything falls into place, you will feel it – the process will go like clockwork. You do not need to press on a tight self-tapping screw, you just need to remove it and try again. A little effort is required only at the very end of screwing.
Now you know how to screw a self-tapping screw into drywall, concrete, brick, wood and metals correctly and what to do in case of “work hitches”.
Battery Charging Procedure
It is necessary to insert the battery into the device, observing the polarity (the corresponding signs “” and “-” are affixed on the battery and on the device), i.e. plus is combined with plus, and minus – with minus.
A glowing red diode on the device panel indicates that the charging process is in progress. This procedure lasts from 3 to 5 hours.
The rechargeable battery is protected against overcharging, so it can be left in the device for longer, but not more than 24 hours..
Self-tapping vs Self-drilling Screws
During the charging process, the battery and the device itself may heat up, which is not an indicator of a malfunction..
Bits – nozzles
The screwdriver comes with several types of bits with different shapes of the working edge.
Bits with a straight edge are designed to work with fasteners that have one slot (slot). A suitable bit is selected depending on its length and depth.
Similarly, the shape of the cross-shaped bit is selected – here the width of the slot and the dimensions of the fastener head itself are taken into account. For reliable operation, the edge of the bit must fit tightly into the slots, otherwise there is a possibility of “licking” the edges of the slots.
To attach the bit to the cartridge, a special attachment with a magnetized holder is used, which prevents the structure from disintegrating and reliably holds the bit in a variety of positions.
To fix the bit with the bat, you need to unscrew the movable part of the chuck.
Insert the nozzle and screw in the chuck as far as it will go.
There are also very convenient double-sided bits that can be fixed in a chuck without a nozzle.
Is it possible to tighten self-tapping screws with a drill
Difficult, but possible. I built a dacha – all the fasteners – self-tapping screws – twisted with an ordinary domestic drill – 400 watts monost, with speed control. the largest self-tapping screws are 6×150. Only the recoil tortured, but pumped up the hands!
I also twisted small screws up to the smallest, here the skill and adjustment of the drill is already important – so that when the trigger is pulled, it slowly turns.
And use the screwdriver as a drill! The drill is very good. big cr. moment. So it tears off, cuts and scrolls. It is better to spend skill on the quality of the result than on the struggle with the obvious.
Sergey
Shl The tool must be used for its intended purpose.
You can screw a self-tapping screw into a tree in three ways, with a screwdriver, screwdriver or drill. The easiest and practically cost-free way to tighten the self-tapping screw with a screwdriver. Wood material is soft and pliable, which allows you to screw a sufficient number of self-tapping screws into it with a screwdriver without much fatigue. In order to tighten a large number of self-tapping screws, you will have to resort to the help of a screwdriver, he will do all the power part of the work for you. It will also not be difficult to screw the self-tapping screw into the wood with a drill, but for this the drill must have a function of smooth adjustment of the rotational speed.
Setting the torque
The drill has an adjusting ring for setting the torque, on which its values are applied.
This is necessary in order to set the most appropriate value when working with materials with different hardness..
For example, for screwing self-tapping screws into drywall (with little effort), a range of values of 2-4 is suitable, and for hard wood, the torque can be set to the maximum figure on the ring.
This adjustment helps to avoid quick damage to the fastener splines..
During operation, you can change the frequency of revolutions by increasing or decreasing the pressure on the trigger of the tool.
This allows you to stop the operation of the tool in time when the self-tapping screw or screw is fully tightened.
How to screw a self-tapping screw into a tree with a screwdriver.
In most cases, you have to twist self-tapping screws into the wood with two types of slot, flat and cruciform. For tightening such self-tapping screws, appropriate screwdrivers with a flat (marking SL) or cross-shaped (marking PH) tip are selected. Also on sale you can find cross-shaped bits with the PZ marking. PZ bits have additional edges and are used for self-tapping screws with a recessed slot. Sometimes flat-tipped screwdrivers are called minus, and Phillips are called plus or curly. In addition to the letter index, their markings also contain digital indexing, which indicates the width of the flat tip or the group to which the cruciform tip belongs. When making furniture with your own hands, most often you have to tighten self-tapping screws with a screwdriver, the diameter of which is from 2.2 to 4.2 millimeters. Therefore, for screwing self-tapping screws with a flat slot into a tree, the designation of a screwdriver must be SL from 4 to 8, and for screwing self-tapping screws with a Phillips slot into a tree, the designation of a screwdriver must be PH or PZ 1 or 2.
Tool set
Usually, such a tool is sold in special cases, where each part has its own place..
The drill itself consists of a main tool and a removable battery, which is recharged from the household electrical network..
A special charger is used for charging, which is included in the kit..
How to tighten a self-tapping screw without a screwdriver and without a screwdriver.
This method of screwing the screws is, of course, an exception to the rule, but in some cases when it is very necessary and only a drill and screws are at hand, there is nothing else to do but to clamp the screw head directly into the cartridge and slowly tighten it. To prevent the screw from scrolling in the chuck, you can hit the edge of the screw head several times with a hammer so that it becomes not round but slightly deformed.
How to screw a self-tapping screw into a tree with a drill.
To screw the screws into a tree, the drill must have an electronic speed control function. In other words, the rotational speed of the drill chuck should gradually increase as the button is pressed. It is also worth remembering that most drills do not have the function of adjusting the maximum force like a screwdriver, and therefore you need to independently control the depth of screwing of the screw and remove your finger from the button in time. An ordinary drill has enough strength to screw the self-tapping screw deep into the tree or even tear off the head of the self-tapping screw..
Work principles
It should always be borne in mind that you are going to use the tool not for its intended purpose, respectively, this is associated with some difficulties and limitations..
Basic rules for safe and efficient work with a drill as a screwdriver:
- Follow safety requirements. Handle the instrument with care.
- It is not necessary to tighten the screws to the end – this is fraught with breakage of the tool, bit or screwing object. Experienced craftsmen advise to underscrew the screws a little, and then finish by hand with a screwdriver.
- For a secure attachment of the bit, it is recommended to use extended bits or a specialized bit holder.
- For wood material, in order to avoid splitting the wood, it is recommended to first drill the holes, and only then tighten the screws..
Of course, it is better to use a screwdriver for such purposes, but a drill will also cope with such types of work..
How to use a drill as a screwdriver?
First of all, you need to select the appropriate tool model for your purposes and by the type of screws / bolts nozzles – bits. They should be installed in place of the drill in the spindle chuck..
Further, if possible, it is recommended to reduce the rotational speed of the mechanism – this will make the work safer, as well as keep the tool and attachments in working condition – at low speeds they wear out less. Some models have speed controllers, while others you can manually adjust the speed by changing the mechanism or electrical circuit.
For experienced craftsmen, it will not be a serious problem to work with a drill as a screwdriver and at high speeds, but there is always a risk of damaging the bit or screw, cutting off the screw head, “screwing” the material through, etc..
It is also worth considering that drilling tools do not have a splitting sleeve (it is responsible for preventing breakage of the tool mechanism when the engine stops suddenly), so the necessary work should be done carefully. It is recommended to use more durable bits than for a screwdriver.
Comparison of screwdriver and drill
To begin with, it is worth understanding the distinctive features of these tools, because, although they both perform a rotational movement, their purpose is different..
The main difference is the rotational speed of the working spindle – the screwdriver rotates much slower than the drill. Also, it has no inertia – the tool stops at the same time when the mechanism is turned off. The spindle, while drilling, continues to rotate for some time after turning off.
A drill is a potentially more dangerous tool than a screwdriver, therefore, when working with it, special safety precautions must be observed – safety glasses, in addition to the usual care, accuracy and caution.
The choice of the operating mode is another difference between the considered instruments. The drill, in addition to the main one, also has an impact mode, while the screwdriver is regulated only by the spindle rotation speed.
As you can see from the comparison, the drill is less suitable for working with screws and bolts, however, it can be adapted for this case..
Is it possible to tighten screws with a drill
Typically, a drill is used to drill holes in a wide variety of materials – it can be wood, plastic, and even metal. There are also grinding and cutting attachments for this tool..
There are several types of drills:
The principle of operation of the tool is to transfer rotation to a drill or other attachment, due to which it is possible to perform various types of work – construction, locksmith, finishing, etc. “If I use a drill for such a large number of tasks, can I find another use for it? ” – so many people would probably think. And the answer is yes, you can expand the list of works for this tool and add screwing screws, screws to it.
Pros and cons of using a drill as a screwdriver
Despite the rather forced use of the tool in an unusual area, such a solution also has some advantages:
- Due to the a priori higher number of revolutions and increased speed, the drill copes with the tasks set faster than a screwdriver;
- Due to the greater effort, it is possible to screw screws into harder and harder materials (some metals, etc.);
- The ability to use one tool for a whole range of diverse work.
There are also disadvantages:
- Drills, as a rule, are heavier and cumbersome – it is not always possible to get to hard-to-reach places;
- To use them as a screwdriver, you need a certain skill;
- The drill is not applicable for thin and fragile materials (plastic, drywall, planks less than 20 mm, etc.), as well as furniture;
- Observance of special safety precautions is required – safety glasses, underscrewing screws, exclusion of shocks during operation, etc.;
- Heavy tool wear (bits and bits) and a significant risk of damage to screws.
It can be concluded that a drill can occasionally be used as a screwdriver, but you should not abuse such inappropriate use..
Ask your question on our forum without registration
and you will quickly receive an answer and advice from our specialists and forum visitors!
Why are we so sure of this? Because we pay them for it!
Why use a screwdriver to screw in screws (in fact, both are drills):
The screwdriver is lighter, therefore it is more convenient for them to work.
2. The shape and weight make it possible to hold it in one hand for a long time.
3. The screwdriver has a reverse, which allows you to unscrew the screws.
4. Smaller size – you can crawl into different places.
As you can see, this is mainly a matter of convenience and comfort of work, you can use an ordinary drill to screw in screws – it does not harm the drill.
Why use a screwdriver to screw in screws (in fact, both drill):
The screwdriver is lighter, therefore it is more convenient for them to work.
2. The shape and weight make it possible to hold it in one hand for a long time.
3. The screwdriver has a reverse, which allows you to unscrew the screws.
4. Smaller size – you can crawl into different places.
As you can see, this is mainly a matter of convenience and comfort of work, you can use an ordinary drill to screw in screws – it does not harm the drill.
Why use a screwdriver to screw in screws (in fact, both are drills):
The screwdriver is lighter, therefore it is more convenient for them to work.
2. The shape and weight make it possible to hold it in one hand for a long time.
3. The screwdriver has a reverse, which allows you to unscrew the screws.
4. Smaller size – you can crawl into different places.
As you can see, this is mainly a matter of convenience and comfort of work, you can use an ordinary drill to screw in screws – it does not harm the drill.
Yes, there is, you just don’t need it, it’s one thing when you have some kind of urgent case and you just need to take and work with what you now have at hand, and another thing for regular work. For her, in any case, you need a normal tool, if we talk about a screwdriver – then this is a cassette version of Bosch or Hilti.
Yes, there is, you just don’t need it, it’s one thing when you have some kind of urgent case and you just need to take and work with what you now have at hand, and another thing for regular work. For her, in any case, you need a normal tool, if we talk about a screwdriver – then this is a cassette version of Bosch or Hilti.
Already many people earn just talking on our forum!
For example, like this. Or like this.
You can start chatting on the forum now. Just log in through Vkontakte or register, it will take one minute.
Don’t Screw Yourself! 3 Tips for Self Tapping Screws
Difficult, but possible. I built a dacha – all the fasteners – self-tapping screws – twisted with an ordinary domestic drill – 400 watts monost, with speed control. the largest self-tapping screws are 6×150. Only the recoil tortured, but pumped up the hands!
I also twisted small screws up to the smallest, here the skill and adjustment of the drill is already important – so that when the trigger is pulled, it slowly turns.
And use the screwdriver as a drill! The drill is very good. big cr. moment. So it tears off, cuts and scrolls. It is better to spend skill on the quality of the result than on the struggle with the obvious.
Sergey
Shl The tool must be used for its intended purpose.