Load The Line Into The Trimmer Spool

Grass Trimmer

How to insert line into the trimmer spool? Instruction

Load The Line Into The Trimmer Spool

The warranty production of the factory trimmer refueling will inevitably require line replacement. Having a very rough idea of ​​how to thread the line into the trimmer reel on their own, beginners are reluctant to take up this business. However, with some skills, mastering this simple teaching does not present any difficulties, and the similar instruction presented below will make this process as easy as possible.

Coil with one working tendril

The simplest option and uncomplicated sequence of actions:

  • The dimensions of the reel and the length of the original factory winding determine the recommended length of the line for winding. 2. 5 m.
  • One end of the line is inserted into the fixing technological hole located inside the spool.
  • The fishing line is wound on the drum in the reverse rotation of the spool in the direction of the trimmer. as a rule, on the inside of the bobbin an arrow indicates in which direction the winding is being carried out.
  • A small section of the fishing line is left free to lead it out. it is fixed in a specialized groove on the inside of the bobbin, designed to hold the winding when assembling the bobbin into working condition.
  • The left end of the line is passed through the hole in the outer part of the reel.
  • The bobbin halves are assembled and put on the trimmer bar.

We wind the fishing line

Slowly completed disassembly of the spool-spool without losing its spare parts allows you to proceed to the main task. winding the fishing line into the reel. Technological features of the spool design and the number of working antennae determine the sequence of actions.

Preliminary preparation

First of all, to wind the fishing line, you need to remove the spool (bobbin, spool) from the trimmer. specific actions will depend on the complexity of the configuration and the type of the product itself:

  • Small electric trimmers with a working position of the motor and the coil in the lower part, as a rule, have side buttons on both sides of the bobbin. When pressed at the same time, the upper part of the spool together with the inner content for winding the line is disconnected, while the lower part remains on the trimmer. It is advisable to disassemble the bobbin on a flat, smooth place so that the spring included in the structure does NOT jump out and does NOT get lost;
  • Electric and gasoline trimmers with a curved bar without the possibility of installing a knife, as a rule, have spools with special lamb: in such designs, hold the spool in a stationary position with one hand, and rotate the wing nut that fixes the Bobbin on the bar with the other hand. After disconnecting the nut, the entire bobbin is removed.
  • Electric and gasoline trimmers with the ability to install a knife on a straight Bar (for example, Stihl trimmers) have a hole under the reel. To keep the rod stationary, a screwdriver or other suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bobbin is fixed. After that, the coil body is scrolled clockwise (with a left-hand thread) and removed from the trimmer.

For the second and third options, the coils, depending on the design, are disassembled in different ways. In the bobbins, a lamb is unscrewed from the lamb, in the coils, the latches are pressed from the latch and one part of the coil is released from the other. If the halves of the bobbin are connected by thread, then it is enough to turn them by hand in opposite directions until they are completely unscrewed.

Coil with two working tendrils

In this type of spools, you should determine the number of grooves for winding the line, lying on the inside of the spool:

  • One groove. both tendrils are wound together in one groove;
  • Two grooves. each antenna is wound on an individual groove.

For both cases, a line with a length of 2-3 m is taken.In single-groove reels, the line is pulled into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the rod side. inside the arrow usually indicates the correct direction of winding. If there are fixing grooves, the ends of the fishing line are threaded through them or held with the fingers of the free hand, they are threaded into the through hole of the outer half of the bobbin, the bobbin is closed and attached to the trimmer bar.

The difference in line winding in two-groove spools is that initially a 2-5 m long line segment is folded in half (to determine the mid-bend), and the bend loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each along its own groove, fixing the antennae and assembling the coil is similar to the above-described option with one groove.

The first execution of this procedure, perhaps, will seem long and rather laborious, but with time and experience this task will be solved much faster and easier.

The following will clearly show how to thread the line into the trimmer spool and wind it correctly. this operation is NOT difficult and with some patience it will certainly be crowned with success:

Automatic line winding to a spool

There is a type of reel in which the automatic mechanism winds itself. from the user it is enough only to correctly fill the line. The fishing line is passed through a hole on the inner part of the body, its antennae without winding are passed through the hole on the outer body, the reel is assembled, and when the winding button is rotated, the fishing line inside is wound independently. It is impossible to make the winding wrong in such a spool: the mechanism itself will determine the correct direction, since it can only spin in one direction.

We wind the fishing line

Sluggishly completed disassembly of the spool-spool without losing its spare parts allows you to proceed to the main task. winding the fishing line into the spool. Technological features of the spool design and the number of working antennae determine the sequence of actions.

How to put line in the Stihl.FS-38 mower

Took the mower out of the barn, but there was NO line in it, I had to put the line and on the occasion took off a small

Preliminary preparation

First of all, to wind the fishing line, you need to remove the spool (bobbin, spool) from the trimmer. specific actions will depend on the complexity of the configuration and the type of the product itself:

  • Small electric trimmers with a working position of the motor and coil in the lower part, as a rule, have side buttons on both sides of the bobbin. When pressed at the same time, the upper part of the spool together with the inner content for winding the line is disconnected, while the lower part remains on the trimmer. It is advisable to disassemble the bobbin on a flat, smooth place so that the spring included in the structure does NOT jump out and is NOT lost;
  • Electric and gasoline trimmers with a curved bar without the possibility of installing a knife, as a rule, have spools with special lamb: in such designs, hold the spool in a stationary position with one hand, and rotate the wing nut that fixes the Bobbin on the bar with the other hand. After disconnecting the nut, the entire bobbin is removed.
  • Electric and gasoline trimmers with the ability to install a knife on a straight Bar (for example, Stihl trimmers) have a hole under the reel. To keep the rod stationary, a screwdriver or other suitable object is inserted into this hole and, with slow rotation, such a mutual arrangement is achieved when the screwdriver enters the hole and the bobbin is fixed. After that, the coil body is scrolled clockwise (with a left-hand thread) and removed from the trimmer.

For the second and third options, the coils, depending on the design, are disassembled in different ways. In the bobbins, a lamb is unscrewed from the lamb, in the coils, the latches are pressed from the latch and one part of the coil is released from the other. If the halves of the bobbin are connected by thread, then it is enough to turn them by hand in opposite directions until they are completely unscrewed.

Automatic line winding to a spool

There is a type of reel in which the automatic mechanism winds without the help of others. that’s enough for the user to just fill the line correctly. How to insert line into the trimmer spool? Instruction. How to remove the spool from the trimmer? How to wind the line in order to fill the line. The fishing line is passed through a hole on the inside of the body, its antennae without winding are passed through the hole on the outer body, the reel is assembled, and when the winding button is rotated, the fishing line is wound from the inside without the help of others. In such a spool, it is impossible to make the winding by mistake: the mechanism itself will determine the correct direction, since it can only rotate in one direction.

The warranty production of the factory trimmer refueling will inevitably require line replacement. Having a very rough idea of ​​how to thread the line into the trimmer reel on their own, beginners are reluctant to take up this business. However, with some skills, mastering this simple teaching does not present any difficulties, and the similar instruction presented below will make this process as easy as possible.

Coil with two working tendrils

In this type of spools, you should determine the number of grooves for winding the line, lying on the inside of the spool:

  • One groove. both tendrils are wound together in one groove;
  • Two grooves. each antenna is wound on an individual groove.

For both cases, a line with a length of 2-3 m is taken.In single-groove reels, the line is pulled into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the rod side. inside the arrow usually indicates the correct direction of winding. If there are fixing grooves, the ends of the fishing line are threaded through them or held with the fingers of the free hand, they are threaded into the through hole of the outer half of the bobbin, the bobbin is closed and attached to the trimmer bar.

The difference in line winding in two-groove spools is that initially a 2-5 m long line segment is folded in half (to determine the mid-bend), and the bend loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each along its own groove, fixing the antennae and assembling the coil is similar to the above-described option with one groove.

The first execution of this procedure, perhaps, will seem long and rather laborious, but with time and experience this task will be solved much faster and easier.

The following will clearly show how to thread the line into the trimmer spool and wind it correctly. this operation is NOT difficult and with some patience it will certainly be crowned with success:

Preliminary preparation

First, to wind the fishing line, you need to remove the spool (bobbin, spool) from the trimmer. certain actions will depend on the complexity of the configuration and the type of the product itself:

  • Small electronic trimmers with a working position of the motor and coil at the bottom, usually have side buttons on both sides of the bobbin. When pressed at the same time, the upper part of the reel, together with the inner content for winding the line, is detached, while the lower part remains on the trimmer. It is better to parse the bobbin on an evenly smooth place so that the spring included in the structure does NOT jump out and is NOT lost;
  • Electronic and gasoline trimmers with a curved bar without the ability to install a knife, usually have spools with a special lamb: in such designs, you should hold the spool in a stationary position with one hand, and turn the wing nut counterclockwise to fix the Bobbin on the bar. How do I fit the line into the trimmer? How to thread the line into the trimmer spool. It is clear how to load the line on the trimmer. After disconnecting the nut, the entire bobbin is removed.
  • Electronic and gasoline trimmers with the ability to install a knife on a straight Bar (for example, Stihl trimmers) have a hole under the reel. To keep the rod stationary, a screwdriver or other suitable object is inserted into this hole, and with a leisurely rotation, such mutual placement is achieved when the screwdriver goes inside the hole and the bobbin is fixed. Then the coil body is scrolled clockwise (with left-hand thread) and removed from the trimmer.

For the second and third version of the coil, the suspension from the structure is disassembled by different methods. In the bobbins, the lamb is turned out from the lamb, in the coils, the latches are pressed from the latch, and one part of the coil is released from the other. How to tuck the fishing line into how to properly cheap fishing line. 2. On your site. If the halves of the spool are threaded, then it is enough to turn them by hand in the opposite directions until they are completely unscrewed.

Coil with one working tendril

The most common option and easy sequence of actions:

  • The dimensions of the spool and the length of the unique factory winding determine the recommended length of the line for winding. 2. 5 m.
  • One end of the line is inserted into the fixing technological hole located inside the spool.
  • The fishing line is wound on the drum in the reverse rotation of the spool on the trimmer product direction. usually, on the inner side of the bobbin, an arrow indicates in which direction the winding is being carried out.
  • A small section of the line is left free to bring it out. it is fixed in a special groove on the inner side of the bobbin, created to hold the winding when assembling the bobbin into working condition.
  • The left end of the line is passed through the hole on the outside of the reel.
  • The bobbin halves are assembled and put on the trimmer bar.

Coil with two working tendrils

In this type of spools, you should find the number of grooves for winding the line, lying on the inside of the reel:

  • One groove. both tendrils are wound together along one groove;
  • Two grooves. each tendril is wound on a personal groove.

For both cases, a line with a length of 2-3 m is taken.In single-groove reels, the line is pulled into a through hole, its ends (antennae) are folded together and aligned, after which they are wound in the opposite direction of rotation of the bobbin on the rod side. inside the arrow usually indicates the correct direction of winding. If there are fixing grooves, the ends of the fishing line are threaded into them or held with the fingers of the free hand, they are threaded into the through hole of the outer half of the bobbin, the spool is locked and attached to the trimmer bar.

The difference in line winding in two-groove spools is that initially a 2-5 m long line segment is folded in half (to determine the mid-bend), and the bend loop is inserted into a special groove between the grooves. Both antennae of the fishing line are wound each along its own groove, fixation of the antennae and assembly of the coil is similar to the one-groove option discussed above.

The first execution of this procedure, perhaps, will seem long and rather labor-intensive, but over time and experience this task will be solved much faster and easier.

The following will clearly show how to thread the line into the trimmer spool and wind it correctly. this operation is NOT difficult and with some patience it will certainly be crowned with success:

How to correctly replace the line in the mowing head, reel of STIHL FS 55 lawn mowers

Single Barbed Trimmer Spool

Reel for single-barb lawn mowers

Many owners and experts note the ease of use and ease of refueling the bobbin with one mustache. Depending on the manufacturer, the length of the threaded line can vary from 2 to 5 meters. The end of the line is inserted into the head into a special technological groove or hole, and the winding is carried out in the direction opposite to the working rotation of the bobbin. Most reels have arrow marks on the outside of the body that indicate the direction of the trimmer reel movement.

After winding, you need to leave a free end of 15-30 cm to enhance the centrifugal force, which is decisive when removing the trimmer line in automatic and semi-automatic spools. Passing the left end through the working hole of the coil and assembling the head.

Trimmer head with two tendrils

Double flute head

After removing the spool from the spool body, we determine the number of strands for winding the line (1 or 2). In principle, there is no difference between bobbins with one and two grooves, but with careless threading into the paired groove, there will be operational problems. Due to the likelihood of interlacing the adjacent line of the tool, a situation may arise when, after wear of the working antennae, it is impossible to remove new ones.

Regardless of the number of streams, a fishing line with a length of 1.5 to 3 meters is taken for refueling. Winding must be done in the opposite direction of rotation of the head, since winding in the direction of travel will lead to the fact that the line will not be removed from the reel. After the fishing line is tucked into the trimmer coil, the free ends (15-30 cm) are threaded into special holes. Next, we assemble the head in the reverse order of disassembly and check the operability. Do NOT worry if the ends of the two antennae are very different in size, because when you start the trimmer, the knife installed on the protection will cut off excess.

Winding the line to the trimmer

Measured and accurate dismantling of the spool from the spit coil makes it possible to go directly to winding the line. The design features of the head, the number and location of the fixing holes dictate the sequence of actions when performing this operation, and also determine the methods used. Today there are several types of reels, depending on the number of line antennae and the methods of threading it:

  • Trimmer head with one working Mustache;
  • Bobbin with two tendril fishing lines;
  • Auto winding reel.

How to wind line on a trimmer reel: key points

A gasoline or electric trimmer is an indispensable tool in the arsenal of a modern summer resident or owner of his own home.

Thanks to these garden devices, even a large garden plot can be mowed with ease. After purchasing this tool and performing several mows, many people think about how to properly wind the line on the trimmer reel. For an inexperienced user, the first operation to replace it will seem problematic and time-consuming, since the developers often do not fully reflect the instructions for replacing the fishing line in the operating manual.

Preparation for winding the line

Before the winding process, it is necessary to remove the spool with line from the body. Depending on the manufacturer, power and type (electric or gasoline), there are three design types of trimmers:

    Compact Electric Trimmers.

Straight bar trimmer

This model provides the ability to install a knife. Removing the coil in such models is done by means of two keys recessed into the coil body. To mount the trimmer knife, it is necessary to align the hole of the reel and the rod, and then insert the device in the form of a steel pin (screwdriver, iron bar). After fixing the coil, the body can be easily unscrewed by hand clockwise.

Trimmer head with automatic line threading

Types of trimmer heads

Some models on the market are fitted with a reel with an automatic winding mechanism. It is enough for the owner to properly thread and fix the ends in the head, and the winding operation will be performed by the tool itself when it is turned on. It is almost impossible to wind the line incorrectly into a trimmer with such a head, since the coil independently determines the position of the antennae. The advantages of the automatic trimmer head include the ease of threading the line, and the disadvantages are frequent breakdowns of the mechanism due to the complexity of the design and the high cost.

No cord feed, coil does NOT spin

An automatic or semi-automatic head should feed the line without stopping the machine. But if She does not come out, then the reasons may be as follows:

  • The line is not wound correctly in the spool, because of which the latter does NOT spin;
  • The cord is wound unevenly, and the thread can get stuck between the turns (the thread should be wound neatly, turn to turn, without distortion)
  • Too short thread ends come out of the holes, as a result of which there is not enough centrifugal force to extract them, and the line is NOT fed (it is recommended to always adjust the length of the cord by pulling it slightly before starting the unit)
  • The fishing line is stuck together (will be discussed later).

Types of trimmer heads

The grass mowing head is a cylindrical body in which a spool (bobbin) is inserted with a fishing line (cord) tucked in it. This design can be installed on both gasoline and electric trimmers. The heads differ in the way of threading and feeding the cord and are of 3 types.

  • Automatic. Cord feed is performed after the user Decreases engine RPM. Although the automatic line feed is convenient if large volumes of work are performed, there is one drawback in such bobbins. a high whine consumption.
  • Semi-automatic. The use of this type of heads does not require the user to perform complex manipulations. The principle of their operation is designed in such a way that the cord lengthens automatically while the apparatus is operating at full speed. It is enough to lightly hit the ground with the trimmer head (this removes the blocking of the cord), and the line is pulled out of the bobbin due to centrifugal force, after which it is cut to the required length with a knife located on the protective cover.
  • Manual. To lengthen the cord, the device must be stopped, after which the line is pulled manually.

Based on the above, semi-automatic bobbins are the most optimal option. It should also be borne in mind that the coils for the trimmer are single-string (used only for trimming the grass) and two-string, which are used for mowing tall grass and small, thin-stemmed bushes.

Second way

Some reels have a second method of securing the cord: you can charge 2 pieces of yarn instead of one folded in half. The line is replaced according to the following algorithm.

  • Before you change or load a new thread into the spool, determine how many meters it will take using the method described above.
  • One end of the cord Fold into a hook.
  • Find the hole at the bottom of the bobbin for fixing the line, and insert the end of the thread bent in a loop into it.
  • It is required to wind the cord according to the direction of the arrow to the required level, and not exceeding the coil diameter.
  • Do the same for the second bobbin compartment.
  • The assembly of the head does not differ in any way from the method that was given when it was considered threading the bobbin with a piece of line folded in half.

For Shtil lawn mowers, there is a very simple and quick way to change the line without disassembling the mowing head, which you can get acquainted with by looking at this.

The ends of the cord protruding from the holes in the casing can be cut to the desired length when the part is installed in the trimmer. This can be done in two ways:

  • Turned on the trimmer (when rotating, the ends of the fishing line will be cut into a knife, fixed for THESE purposes on the protective cover)
  • Cutting off the excess ends with scissors so that they DO NOT touch the casing body.

The second method is used if a large diameter cord had to be supplied, and the edging knife cannot shorten it.

If a charge was made to whine into the mowing head, but the length of the protruding ends of the cord is insufficient, then they must be lengthened before starting the machine. this applies to the head with manual adjustment. However, there are cases when using a semi-automatic mowing head, when, due to the insufficient length of the protruding ends of the cord, they do NOT automatically lengthen. In this case, it is necessary to turn off the unit (on electrical apparatus, it is imperative to unplug the plug from the socket), manually press the button located at the bottom of the part, and pull out a little line. After this procedure, the cord can again be extended due to centrifugal force, if you set the maximum spindle speed.

Line problems

Users of trimmers, both gasoline and electric, sometimes have problems with the cord. “Advanced” owners of mowers easily cope with difficulties in automotive products, understanding why this happens, and for beginners. these are problems that have no rational explanation. But in fact, everything is solved quite simply. The most common problems that happen with the line are as follows.

How to remove and disassemble a coil

Before starting the process of changing the cord, it becomes necessary for trimmer users to remove and disassemble the coil. Let’s see how to do it.

The trimmer mowing head consists of several parts: a cover, a spring (not on all models), a spool with a cord and a cover.

In trimmers, 2 options for mounting the mowing head are most often used.

Option number 2

In this embodiment, the head is screwed onto the gearbox shaft. To remove it, you need to fix this shaft. To do this, in such trimmers, for example, in the Huter and Champion devices, a hole is provided through which you can insert either a thin screwdriver or a metal rod.

So, to remove the bobbin, follow 2 easy steps.

  • Insert a screwdriver into the hole and lock the shaft.
  • Grasp the head body and start turning it clockwise. Torque in this direction follows because the thread cut on the shaft is left.

Changing the line to a disc or knife

When ennobling a personal plot, park areas and other places where it is required to mow various kinds of plants, it is often necessary to change the cutting tool to trimmers. This is dictated by the fact that the standard pipe installed in the mowing head can only handle grasses. But when a bush or young growth of trees appears on the path of the worker, the fishing line cannot cope with such a task, and it needs to be changed to a more efficient cutting tool.

Trimmer manufacturers have foreseen such situations, and supplemented their products with a mass of attachments in the form of knives with several “petals” or in the form of discs, similar to circular saws.

If you replace the fishing line with a knife with several “petals”, then this tool can mow both Tall grass and plants with thick and dry stems. And by changing the fishing line to a disk, the lawn mowers user becomes able to cut shrubs or small trees.

Knives and discs are installed according to the following algorithm.

  • The first step is to remove, lock the shaft, the mowing head (turns clockwise) or the boot nut, if the unit has NOT been used yet.
  • Place the dust or cutting knife so that it fits over the small protrusion (bushing).
  • Install the attachment cover on top of the knife and screw the nut onto the shaft (counterclockwise).
  • Tighten the nut (counterclockwise) with a pipe wrench.

    • For a better understanding of the tool changing process, see this.

    How to change the line to the trimmer

    The trimmer is the most common machine used for cutting grass and small bushes. This device is distinguished by its simplicity in service, simple operation during operation, and due to its low weight, even women can handle it. It is no secret that the correct selection of cutting tools is required for high-quality performance of work on mowing grass. As the latter, special cutting attachments (discs, knives) or trimmer heads with a fishing line inside are used in trimmers. Nozzles and line are expendable tools, but if the knives can be sharpened, then when the line is used up, it must be replaced. In this article, we will tell you in as much detail as possible how to properly replace the fishing line.

    Line winding algorithm

    Depending on which trimmer model is used, the type, thickness and length of the line are selected. The diameter of the cord can be from 1.2 to 4 mm. It is not difficult to guess that the thicker you fill the cord, the harder and thicker grass it is able to cut.

    There are 3 ways to find out which line diameter you can use on your mower.

    • View information on the thickness of the cord in the instructions for the device.
    • Look at the bobbin itself. It can contain information about the possible diameters of the line.
    • Insert the line into the outlet. If it easily passes into it, then a cord of this diameter can be used.

    The line is wound on a reel in the mowing head. Therefore, you first need to open it (this was discussed above). There are 2 ways to wind the cord.

    How to wind the line correctly on the trimmer spool?

    Despite the fact that gardening equipment has been used for quite some time, it is still a novelty for some owners of private houses. That is why there are often questions about how to properly wind the line on an electric or gasoline trimmer.

    This is essentially a simple operation, but all its stages must be performed correctly in order to achieve the desired result. over, in the operating instructions, only a few manufacturers provide an answer to this sore question. Explore the article and find out how the line winds around the trimmer reel.

    The procedure for winding the line on the trimmer spool

    First of all, you should know that trimmers have different working attachments. The reel can be designed for different lengths and thicknesses of the line. this point should be taken into account when purchasing consumables.

    So how does the line load into the trimmer reel? All work is divided into several stages:

    • First you need to disassemble the trimmer head.
    • Unscrew the nozzle by rotating the drum to the right.
    • Press with your fingers on the two latches located on different sides of the tap holes and remove the top cover of the nozzle. You can pry off the cover with a screwdriver. This should be done carefully: reels with automatic line feed have a spring that can forcefully throw the cover along with all the contents of the reel.
    • Remove scraps of old fishing line.
    • Now you need to find the middle of the line. To do this, unwind it to the required length (for example, 10 m), cut and fold in half.
    • Hook the middle of the line into the existing groove or insert it into the hole specially designed for this. And start winding. The direction is indicated by the arrow, which is usually marked on the trimmer reel body (usually against the rotation of the drum). Some models have a double-sided reel: in this case, the line should be wound in different directions: one end in one direction, the other in the other, while the loop of the line must be inserted into the dividing slot in the middle.
    • Leave loose ends of the line about 20cm each. Later they will need to be fixed in the recess.
    • And finally, the last step is to assemble the drum. Reinstall the washers and spring. On the top ring of the reel there are two notches where you need to tuck the antennae of the fishing line. Thread them through the holes and place the spool in the drum, trying to tighten the line without displacing the spring.
    • Place the drum cover on top and close it with your fingers. The latches will snap into place with a distinctive click.

    When you turn on the trimmer, the excess line will be cut off by the trimming blade.

    As you can see, winding the line on the trimmer reel is not difficult: the main thing is to do everything right. And here are some more tips that will come in handy when choosing a fishing line, winding it and subsequent work:

    • Fishing line comes in different thicknesses and with different sections. The best option for winding is the “native” line for this model;
    • Under no circumstances use fishing line or metal cables for the trimmer. This replacement may seem effective, but it is very dangerous. Jumping off a working trimmer, the cable can seriously injure Not only the lawnmower himself, but also those around him;
    • The line is cut when the trimmer is in contact with hard objects. Try not to allow this, otherwise you will have to stop each time, turn off the device and rewind the line on the reel;
    • Use regular line for lawn mowing and pigtail line for coarse weeds. It is more durable and will not constantly cut.