Makita’s engine replacement on the lawn mower.

How to make repair of the lawn mower with your own hands?

Those who have land are very familiar with what struggle is weed.

Especially when it often rains and the grass grows not by the day, but by the hour. Earlier, and sometimes even now, this issue was resolved with the help of a good old braid for grass.

But technologies are not standing still and now in this case, assistants such as electric and gasoline lawn mowers help.

makita, engine, replacement, lawn

Electric Strimmer Repair. Makita DUR181 Electric Motor Replacement. Whipper Snipper, Trimmer, Repair

The gasoline mower has several significant advantages over electric, such as mobility and lack of danger of electric shock. But there are many drawbacks, for example: high price, a lot of noise, expensive fuel and significant weight.

Electric mowers are cheaper, easier, work on inexpensive energy, and are not difficult to maintain and repair. These advantages become the main reason for their great popularity among buyers of this type of technique.

But despite the pretty good quality, improper operation and a lot of load, they can disable the device. In such cases, you should not immediately carry the device to the repair shop, but try to find and eliminate the cause of the breakdown yourself. over, as mentioned above, electric lawnmands do not have as many nodes and details as gasoline.

The main thing is to have some tools and faith in yourself. In this article, I will just show you how I did my own repair.

AL-KO, the lawn mower of the company, has serious problems in work, namely: the engine stop without load and its strong overheating, was taken as an example. The motor stops, buzzes and start it again, only repeated pressing the Start button helps. The button has to restart almost every 30 seconds, and with further work and more often.

Of course, you can work, but it is very annoying and gives the feeling that somewhere the problem is. Therefore, I wanted to figure out where?

After the mower was working within an hour, the engine temperature was measured. It was impossible to touch him with a finger. He directly radiated heat. If you continue to pay attention and continue to work on such a mower, an electric motor will inevitably fail.

It is necessary to determine the cause of the motor overheating. To do this, remove the top cover of the case, under which the engine is located and its power chains.

The lid is held on six screws with a hat under a cross screwdriver.

Unscrew these screws and remove the lid. upward.

Having removed it, you can see the impeller, the capacitor, two connectors and the engine itself.

makita, engine, replacement, lawn

At first glance, no special problems are invisible. The engine winding darkened slightly from the temperature, but so far it is not critical.

To more carefully inspect the capacitor, it is necessary to unscrew the mount and pull it out.

The capacitor of some external damage did not show.

To check it, you need to disconnect the capacitor and feed the engine for a short time. If he did not start and began to buzz, then the capacitor is intact, because the engine was launched with him. Disconnect the power and connect the container connector back to the engine circuit.

Next, try to twist the impeller. It is mounted on the axis of the rotor and rotates rather tight.

And the reason for such severe rotation is a mechanical brake, which for safety stops the engine rotation when the power is turned off.

It looks like a sleeve that moves freely from top to bottom, along the rotor axis.

Когда напряжение на двигатель не подано, эта втулка прижимается верхней частью о крышку, на которой приклеено две резиновые полосы. Thus, the knife is inhibited on the rotor shaft.

When feeding, the brake sleeve under the influence of the magnetic field is drawn to the center of the rotor and provides free move.

With a careful examination, this sleeve with the brake noticed that at the time of turning on the engine, the brake is retracted and gives the shaft free rotation, but after 2-3 seconds it is released again and begins to slow down the motor. This should not be. Hence the stop of the knife during operation and overheating of the engine.

To find out what is the reason for this work, you need to remove and disassemble the engine.

To do this, disconnect the connectors and put the device on the side to get to the clamping screws. Access to them closes a knife with mounting elements.

To remove it, first you need to unscrew the knife bolt (cm. Figure below).

Direction of rotation, like a regular bolt, and not with left thread. That is, unscrew it counterclockwise, and tighten the clock.

The head of the bolt is plastic, so using the key, it must be well planted so as not to “lick” the edge.

After extracting the bolt, the knife and its plastic disk are removed.

Under it is a height sleeve. With its help, you can slightly lower the knife.

makita, engine, replacement, lawn

Adjustment is carried out by the washers put under the sleeve (see. drawings below).

We remove everything, only the engine shaft and the hexagonal screws of its fasteners remain.

The key for these bolts has a distance between faces of 6 mm. Unscrew them counterclockwise. Removing the last screw, with one hand, hold the engine.

Next, put the mower on the wheels, and clasping the engine with our hands. we raise it.

To disassemble the motor, you need to free tightening studs. We unscrew them all.

Remove the impeller with two screwdrivers.

We proceed to the removal of the back cover. A wooden block and a hammer will help this.

But first you need to mark the position of the covers with something sharp to the engine body.

Put the engine on the side and hit with a hammer, through a wooden gasket, on the rear shaft.

The motor at that moment should hold another person.

We hit until the axis comes out of the bearing to the end.

The engine replacement on the lawn mower with a more powerful.

About five years ago I got an old lawn mower from a neighbor. He complained about problems with the motor, and the fact that he developed his resource. I plunged it a little and after which he worked for four years lifting oil. And last summer the engine ordered to live long. The attempt to repair it has ended in failure. There were no spare parts. Buying a new lawn mower for 25000r was strangled by a toad. And I decided to change the engine for a new.In one of the stores, I saw a similar engine, but the seller replied that there were many problems with the replacement, besides, the price was bitten by their price. I climbed the Internet. On the pages of the Sadovaya-Mototehnika site.ru/ found many offers of engines with a vertical shaft. I began to select the motor and contacted the seller Sergey Anatolyevich, who patiently listened to my wishes and gave some tips, which are as follows: 1. Determine the power of the motor (working volume of the cylinder). I came to the conclusion that my engine is 0.156l2. Determine the type of engine. For the lawn mower, it differs in that there is a brake, and the ignition switch associated with it. On engines for walkways, control is different. You can put it, but with a “collective farm”.3. Determine the length, diameter and shaft shape.

Determine the size of the Carter flange. (As a rule, they are the same for engines 0.140-0.170l, but I neglected it) 5. Determine the shape and distance from the gas tank to the box. (here I took a chance, there is the opportunity to file and feed) unfortunately the 0.156l engine was not on sale, and I did not want to buy less power, t.to. You have to mow in a large area, where not only grass, but also a shrub. Therefore, we stopped at the Champion G170-1VK engine Vertical shaft (5.5 liters.With.). In the option for the lawn mower. Sergei Anatolyevich checked everything, the goods were paid and sent to the Code of TC “SDEK” and three days later I received it in complete completeness at the terminal of SDEK. 7400r. per engine (a discount was operating); 500r. delivery to the NECK; 581p. TC for delivery to the terminal.

The installation of the installation had to be removed from the box and adjusted it by Richtezing (dented everything that interfered), in the area of ​​the oil neck

and in the area of ​​the throttle control mechanism

After that, the engine was screwed to the box with 4 M8 bolts, while 3 holes in the box coincided without problems, and the 4th had to be drilled.And after painting and drying the box, a new motor was installed on it.

The lawn mower was covered by three kilograms, so I had to strengthen the handle, welding the lining at the place of attaching it to the box. I also had to make a new hole to shorten the handle, since the “brake” cable turned out to be short.

makita, engine, replacement, lawn

I had to transfer the stop of the cable shell.

The knife was attached by a bolt of M8, the veneer used the old one, undermining it by about 0.5mm

Successful tests were successful, but then I found fuel flow. Turned out to be weak Chinese spring clamp. I had to replace with a simple.Well, such a mower turned out.

Problems with the mechanical part

The mechanical system in lawn mowers with different drives consists of the following structural elements and nodes:

  • knife (rotary or cylindrical type) or fishing line;
  • transmission mechanism;
  • grass collector and grass emission devices;
  • wheels, handles and housings.

The failure of the cutting element

The most commonly damaged (for example, bend) or knives are blunt, the fishing line for the trimmer ends. This is easily detected with a simple visual inspection.

The fact that the cutting nozzles have become swept away is evidenced by uneven cutting of herbal stems when the lawn mowed.

Over time, knife fastening can weaken. Their balancing during rotation is disturbed, and vibration, whistle, rattling appear. If the knives are damaged, then during operation the mechanism will begin to perform unguided, sudden, sudden movements. To eliminate the malfunctions of this kind, the cutting elements are set to the right position, replaced with new ones or repaired. If possible, then the blades are pulled again.

Sounds and vibration during work

Uncharacteristic sounds, vibration, rattling appear during the operation of the unit, when the fasteners of its structural elements are weakened: body, engine. These phenomena are more often found in gasoline models, because their motor fluctuates more strongly than the electric motor. To eliminate these phenomena, check all the connections, pulling up the bolts if necessary. It happens that the whistle during the operation of the unit arises due to the entry into an outsider that blocks the video in the aerator. In this case, it is enough just to get it so that the sound stops.

Cutting nozzles do not rotate

Often, when mowing a high herbal cover or hard herbal, cutting nozzles cease to rotate due to grass clogging. This problem in most cases (if it has not led to more significant negative consequences) is easy to solve with your own hands, just picking out a stick with a stick.

Damage to constructive details

Damage to the wheels, handles and housing rarely happen. If they are significant, then they change these structural elements. Methods of repair, with its possibility, in each case, depend on the material of broken parts. they can be plastic, aluminum, steel.

Brand break

With prolonged operation, the braids wear out, stretches, and then the belt breaks off. At the same time, the device’s gasoline engine works, but the knives do not rotate. Self.propelled models can also break off the wheel drive belt: then they stop and do not go. Sometimes the clutch cable simply stretches and it needs to be adjusted.

The most common breakdowns

Any technique sooner or later fails. It is important to know how to repair mowers, because not in all cases you need to contact the service center.

The braid does not cut the grass

In most cases, the cause is dumb or severely damaged knives. To achieve the best results, just change the knife every year. Choose a knife suitable for your model. When the knife is swept away, you can sharpen using electrofig or file. When sharpening, be sure to use goggles and gloves. Angle of sharpening on both sides. about 30 degrees.

Simple sharpening devices can be purchased in stores. Before installing them, it is necessary to turn off the mower from the network and adjust the cylinder positions in such a way as to highlight the maximum cutting gap.

In cylindrical braids, the gap between the knife and the cylinder should be less than the thickness of the sheet of paper. Some of the most modern models have built.in regulators with notches. In other cases, you will have to use keys and screwdrivers to carry out the necessary adjustments. Follow the uniformity of the gap along the entire length of the cylinder. To check the adjustment, insert a sheet of paper between the cylinder and a knife, slowly rotating with your hand. Gradually adjust on both sides until the paper begins to cut purely at each point of a motionless knife.

It is difficult to move the mower

  • When the mower hardly moves along the lawn, you may try to remove too high grass and you will have to adjust the level of mowing. When seizing rollers or wheels, they need to be inspected to make sure that there are no scraps of grass and garbage. Most likely, they need to be removed and cleaned.
  • If an interference for air is formed, then the lifting force will decrease on the mowing air pillow, and it will become difficult to move it. Air lack leads to overheating of the engine. Disconnect the power and remove the remaining grass from the air intake grilles.

The technique does not turn on at all

Long and wet grass can easily block the knives. Pull the fork from the mains and with the help of a wooden object rotate the cylinder to the other side of the knife until the movement becomes free. For gasoline mowers, this technique cannot be used.

A belt that provides the operation of cylindrical lawn mowers, wears out, stretches and can break through. Remove the belt cover and check, there was a gap or belt just jumped off. Unscrew the mounting screws and move the small leading pulley to a large cylinder pulley. Put on a new belt on a small pulley and slowly rotate the big one, gradually putting a belt on it. Push the pulley to the side to stretch the belt, then tighten the screws.

Before installing the lid, be sure to check the belt tension. the degree of bending should not exceed 4 mm (the indicator may fluctuate slightly depending on the model, detailed information is contained in the user guide).

Gap in the cord

With every use, you unfold, move and turn the cord. This can lead to a break in the internal conductors. For many models, the cord is connected to the screw terminals, which makes it possible to quickly check it and replace it. If double isolation, a two.core cord is connected.

Other models use clamping contacts that facilitate the replacement. Disconnect the power, separate the plastic cover. When you unscrew the clamping bar, pay attention to the connection of the cord to the switch to comply with the polarity of the connection (wire color).

In order to disconnect the cord, insert the hexagonal key into each of the holes in which the conductors are placed. to free the clamp and the conductor. Check where the gap has formed.

If necessary, connect a new cord: twist together all individual wiring of each core, then insert the twisted ends into the corresponding terminals. Pull slightly to check the connection. Then install the clamping bar, the cord bushing and the circuit breaker cover.

Toro recycler Honda engine swap

Typical breakdowns of gas mowers Makita

According to Servy statistics, the main malfunctions when working with the Makita lawn mower are:

  • Makita gasoline lawn mower is not started, there is no spark formation of the cause: the spark plug is faulty, the ignition coil (magneto) is faulty, damage to the parts of the manual starter, the fuel system, wear of the cylinder-piston group;
  • Makita’s lawn mower stalls, possible reasons: blockage of the fuel system (no fuel supply), wear of the cylinder-piston group, a carburetor, blocking of an air filter;
  • The Makita self.propelled lawn mower does not go, the main reasons: the drive belt is worn out or torn, the drive gearbox, the wear of the drive gears of the drive wheels, the tension of the drive belt, was not adjusted, and the progress control cable was not adjusted.
  • Makita electric gas.beam does not turn on. Reasons: the electric cable is damaged, the switch is not in good condition, the electric motor is not in good condition;
  • The Makita electric lawn mower does not spin the knife, the possible causes of the breakdown: the adapter (impeller) of the knife is damaged, the electric motor is not serviceable;
  • The self.propelled lawn mower does not go, the main reasons: the drive belt is worn out or torn, the drive gearbox, the wear of the drive gears of the drive wheels, the tension of the drive belt, was not adjusted, and the progress cable was not adjusted.

These defects are typical in Makita lawn mowers: some are more common, others less often. And not rarely occur due to the simplest reasons: improper operation (no maintenance is carried out), the use of non-high-quality benzo-mixture (oil and gasoline) or changes and jumps in the power of the electric network, many hours of uninterrupted operation of the lawn mower, many hours of uninterrupted operation of the gas mall Board of the gas mowing housing on the side or wheels up. However, all breakdowns with a proper and professional approach are easily repaired by specialists of the Servy service center.

Just leave a request for repairing the Makita lawn mowers on the site or call us by phone. our specialists SC Service will answer any of your questions.

Notes

The exact repairs are always indicated only after diagnosis. The cost of “Service” services is introductory in nature and can be changed after the diagnosis of your technique. With each client, we work individually and a detailed calculation of the repair price is made in accordance with the level of complexity of the breakdown of a particular type of equipment. Spare parts that we use in the repair are paid separately. Calculation based on data from the Servy client base.

The main malfunctions of the lawn mower

Рассмотрим основные виды неисправностей газонокосилок Makita, причины их возникновения, а также способы устранения.

  • The device is rattling and issues an unusual roar to it. These sounds, as a rule, indicate that the electric motor bolts are weakened, or the device case is poorly fixed. To fix this breakdown, you need to check the bolts. Revealing the backlash, just tighten the bolt denser. Due to the substantial vibration of the electric motor and corps with these problems, the owners of the lawn mowers often face.
  • In the process, a strong vibration of the device is felt. The most common causes of this are the weak mowing mechanism located on the shaft of the electric motor, or the breakdown of the mowing knife. The repair is limited to tightening the bolts. In case of damage to the knives, they need to be replaced or sharpened.
  • The device unevenly cuts grass. The reason for this may turn out to be that the knives are dull. Knives should be sharpened or replaced.
  • During the operation of the device, the front wheel drive stops. The reason is in the strong deterioration of a drive belt, which must be replaced. Perhaps the clutch cable is stretched: then it is necessary to adjust it.
  • During the operation of the device, its engine stops immediately after turning on. This happens when the crankshaft or piston is seized. Sometimes the reason is that there is no oil in the crankcase. Check if there are oil, or give the cornering parts manually, but the best solution is to contact the service center.
  • The engine engine does not turn on. This malfunction can have many different reasons, more of them will require qualified assistance to the service center specialists. The most common of them are a cable break (in electrical devices), the refusal of the power supply or the discharge of batteries (in battery lawn mowers). Often the spark plug is unusable or the fuel ends. Such problems are corrected elementary. If the problems are in the engine, you will have to go to the service center.

The cost of repairing the lawn mower

How much does the repair of an electric gas? The cost depends on the technical and functional parameters, as well as on the complexity of repair work and the of spare parts. By the way, we put only original spare parts. Where to repair the gas mowers Makita? We have all types of repairs (warranty, post.warranty) in our workshop). In addition to eliminating malfunctions in the lawnmands, we will repair a different equipment, including repairing the Makita jigsaw.

For all you are interested in the tools for repairing the tool, call: 7 (495) 530-70-07 Koor: 120

Stationary and outgoing repair of the Makita lawn mower and the basement of the lawn mower to be in the country and you do not want to drag it to call a specialist. By calling or leaving a request on the site. Our experts will arrive and repair the Makita lawn mower right before your eyes. For a more accurate order, check the model of your mower and symptoms of a malfunction. If the malfunction cannot be eliminated on the spot, we will deliver it to the service center for free.

Repair of Makita lawn mowers is one of the specialized activities of our workshop. Having decided to become our client, you will receive excellent service at an affordable price.

We practice an integrated approach to solving the tasks. In many cases, repair and replacement of nodes are not required. Our experts will conduct full diagnostics of equipment taking into account your complaints regarding the problems that arise. We will tighten the weakened fasteners, put the knives in a proper position, clean the filter. Our goal is to increase the performance of the device without replacing nodes.

Always in stock running consumables and spare parts for mowels Makita!

We will provide operational assistance, if any detail is damaged, failed or spent its working resource. Our experts have access to the reserve of original structural elements and nodes. They will restore the efficiency of the device in the shortest possible time.Our masters will provide comprehensive recommendations for the operation and maintenance of Makita lawn mowers. This information will help extend the life of the machines and avoid frequent visits to service centers.

We are proud of the reputation of a reliable performer. Our masters undergo regular trainings and improve their own qualifications in Makita. Fundamental knowledge about the device and the principles of the operation of the lawn mowers of world brands help them identify the cause of the breakdown for half an hour. Turn the support of competent specialists. Entrust the maintenance and repair of Makita lawn mowers to professionals!

Repair of the lawn mower makita

Our price is compiled on the basis of average market prices, because we buy spare parts directly from manufacturers.

Repair for 1 day

Even if after diagnosis you decide to postpone the repair or abandon it at all, in any case, the service will be provided free of charge!

Free departure of the master

The specialist will arrive for a call within 40 minutes, after applying for an application. The exit will be free, even if you refuse repairs!

Why is the lawn mower out of order

Repair of Makita lawn mowers is better to trust professionals. To eliminate malfunctions, knowledge, experience and appropriate equipment are needed. Self.repair of the engine of the lawn mower can lead to serious breakdowns, which will significantly increase the cost of service.

  • The equipment is stored in violation of the conditions recommended by the manufacturer;
  • Sudden voltage drops;
  • Untimely oil replacement;
  • Use of low.quality fuel;
  • Installation of incompatible cutting tools;
  • Mechanical damage;
  • Incorrect valve adjustment.

Our craftsmen will carry out professional repair of the Makita gasoline lawn mower, eliminate any problems in the operation of equipment.

Advantages of contacting our service center

We are professionals with 10-year work experience that will repair electric lawn mower and gasoline models on the day of circulation, set up equipment for the optimal operating mode. Up to 80% of malfunctions is eliminated on the day of circulation or repair is carried out at the expense of the service center. We have our own warehouse with an assortment of original spare parts and duplicates, so customers independently choose which parts to install.

Repair of the lawn mower makita

It is convenient to have a specialization in the repair of Makita lawn mowers for our service center, as this allows you to delve deeper into the problem and perform all the work quickly and efficiently. As a rule, if you get a job, a person comes to work, who claims that it can repair the technique of any brands and models. you can’t call him a professional. Each master has a certain specialization with which he copes best. And we have masters who work best with the technique of this company.

Service center Makita Club

The Makitaclub service center offers the Club Service service for all our customers. Having its own delivery service, the Makitaclub service center offers the Club Service service are ready to cause failed Makita to the service center and back to the client to the client.

  • This is convenient. our service is delivered and a tool fence from the office, house, warehouse, construction site and from any other place.
  • This saves your time. no need to go anywhere.
  • This saves your road costs. our delivery is absolutely free within the MKAD for tools purchased in our company.
  • This is profitable. the cost of repair does not increase! We take the tool for warranty and the post of warranty repair!
  • The cost of all spare parts for the price of the manufacturer!

Service maintenance

  • Warranty repair is a certified authorized service center Makita. We carry out warranty repair of the entire assortment: power tools, battery tools, gasoline tools and measuring equipment. Diagnostics for free.
  • Paid repair of the end of the warranty period or non.warranty cases we carry out any paid repair. After the diagnosis of the tool, with the consent of the repair, the cost of the diagnosis is not paid.
  • Sale of spare comps of specialists will help when selecting parts, send the tool circuit if necessary.
  • Delivery to a service center and back to a customer.operational call of a car for free for our buyers inside the Moscow Ring Road. Club Service Service.
  • A operational deferment of payment to corporate clients of repairs acceleration for corporate clients is possible, it is possible to coordinate the deferral of payments. Thus, the repair time is significantly reduced. no need to wait for the receipt of payment to start repairs.
  • Personal manager for corporate clients, each corporate client, is assigned a personal manager who will advise on goods, the availability of parts in the warehouse, prepare an account, organize a tool to take a tool for the service and repair of the park of your tools, provide reconciliation acts and originals of shipping documents.

Advantages

  • Fast and professional repairs
  • Special branded equipment for diagnosing the Makita Club tooling center is equipped with specialized branded equipment for diagnosis and repair. A special washing camera is used to clean the tool inside from metal and concrete dust, removing old lubricant.
  • Large warehouse of spare parts for spare parts in their own warehouse. Daily replenishment and supply of missing parts.
  • Only the original spare parts of MakitaS use the original spare parts allows you to give a guarantee for the repairs performed.
  • Certified craftsmen of the service center of the master who have passed qualified training. Work experience for more than 10 years.
  • Competent consultants consultants are always ready to help you and advise by phone, email or WhatsApp.
  • Experience with large clients are ready to help companies that want to reduce their costs for the purchase and maintenance of power tools when switching from European brands to Makita equipment

Order form “Club Service”.-

Contact information schedule: