Adjustment and adjustment of the plow on a walk.behind tractor
Before we start to understand how to plow a walk.behind tractor with a plow, you need to prepare the same.based tractor for soil plowing:
- one. To get started, move (roll) one.axle tractor to an even place on your site.
- 2. Prepare soil hooks and interchangeable axes.
- 3. Replace the wheels with tires on a walk.behind wheel with soil hooks, which are installed on interchangeable (elongated) axes.
How to plow a plow on a walk.behind tract, recommendations
Motoblocks to many owners of personal plots and gardens facilitate manual labor. The same tractor, with its proper operation, will become an indispensable assistant in your farm. But not everyone knows how to plow a plow on a walk.behind.
Rather, they do not know how to properly prepare a single tractor and a plow for plowing and cultivating the earth. But, it’s not so difficult. Study our recommendations, and you will succeed.
Now that when we have decided on the walk.behind tractor, we will find out how to plow a motor block correctly. Small areas are best processed using a cultivator or cutter. The supply of light and medium.sized walk.as shoes includes with milling.
Soil plowing technology with their help is simple. It is simply a single tractor is placed on the edge of the site, an increased gear is turned on and, holding it, we follow it, turning 180 degrees at the opposite end of the site.
A completely different thing to plow with a plow in a large area. The correct adjustment of the plow is very important here. Suppose it is done correctly.
Then, at low speed, a control pass is made from one to the other edge of the site, on which we unfold one.axle tractor and perform the reverse passage. At the same time, we put the one.based tractor with the right wheel in the middle of the furrow, which remained from the first passage. We carefully observe the plow. Taking into account the inclination of the walk.behind tractor, the plow should stand perpendicular to the plane of the earth. If this is not, then adjust the plow again.
Then the second passage is made and the depth of the furrow is evaluated. If the depth is too large or too small, then adjust the plow. As a rule, with plow plowing, the depth of the grooves should be within 15-20 centimeters.
As the plowing is mastering, when your furrows become even, you can raise the speed of the walk.behind tractor. Then the plow will dump the ground stronger, its surface will be even, without lumps, and the plowing itself will go faster. That’s how they plow with motorcels.
With what kind of attachment equipment the one.axle tractor works
Any experienced farmer knows that with the help of a walk.behind tractor, cultivator or other motor vehicles it is possible to mechanize almost all agricultural work, starting from the cultivation of land to prepare it for crops and ending with transportation of the collected harvest. Universal motor units became due to the possibility of using a variety of attachments. So, for example, for the cultivation of plowing land and cultivation of virgin lands, not only dumpy and other plows are created, but also: also:
The harrows serve in order to plow the virgin lands, as well as for pre-sowing or after-harvest loosening of arable soil to a depth of 7-14 cm. With the help of harrowing by a motor block, a cultivator level the surface, close moisture, destroy weeds. The working bodies of such agricultural guns are metal teeth or spherical disks. On this video you can clearly see how to plow a walk.behind engineer and a home.made harrow.
With the help of the cigarette light, the potato is carried out, cutting the grooves for sowing seeds, filling the planting material, as well as sprinkling weeds directly in the row zone. Fucking devices are single.row and two.row, with a fixed and adjustable capture width, distinguishable both by a constructive solution and in their effectiveness. Here is a video of how the uno-ears tractor Neva MB2 is processed with a hinged two-row cigarette and aquatic manner.
Soilofreza can plow virgin ground, conduct pre.sowing and basic cultivation of plowed land. This agricultural gun allows you to milling, cultivating the Earth and qualitatively prepare it for sowing. It is capable of not only plowing the soil, but also crush large layers, mix with fertilizer, chop the particles of the impact, smooth the sown area. Soils for plowing are of different types, depending on the number of cutting elements. This video shows how to actually plow a walk.behind tract with a mill installed on it.
Ploskorovka plane cuts helps weeds, cleanse and cut the grooves without turning the layer, plow and crush the ground. Flat cutters come with all kinds of capture width and depth of processing, which allows you to choose them for specific conditions for processing agricultural allocations and crops. About how to process the processing with a hinged plane cutter well shows this video on the example of the Dnieper Motoboblock.
In addition to the listed removable tools created to plow virgin lands and process arable land, rakes, laborers, seeders, grinders, cultivators, rotor and segmented, sprayers, sprayers, brushes, snow.offers, snow.offers, etc. are used with a motor unit. Having the main set of attached agricultural guns, you can perform all kinds of economic tasks with a motor block or a powerful cultivator, in particular, pre.sowing plowing of the earth, sowing and planting crops, introducing fertilizers, inter.row processing of crops, cleaning root crops, seasonal preparation of green feeds.
one.axle tractor for plowing earth
Experienced farmers are well aware of how important it is to carry out high.quality cultivation of land before landing, as well as autumn. The productivity largely depends on this
If earlier it was necessary to spend whole days on such work, now you can use the same.based tractor that will cope with the task in an hour. When choosing a high.quality and productive device, you can process in two hours the area on which it would be spent all day with manual plowing.
When choosing an assistant for working on a farm, many are wondering whether it is possible to process the Earth with the Neva by the Neva motornote or another model or a motor.cultivator is better. In fact, there are no significant differences between these types of technology. Many farmers use both one and the second name to designate ordinary motoblocks.
Cultivator handling during work
While working with the cultivator, be sure to follow your limbs so that they are not close to the moving parts of the cultivator. It’s better to work in closed shoes: high boots, and even better. in boots. Schoolpanians or vietnamese reserve for other purposes, here they increase the risk of injuries. It is advisable to plow the earth with glasses and gloves.
After turning on, the cultivator does not need to push, it is simply set in the right direction. Когда агрегат застопорится в земле, слегка покачайте его с одной стороны в другую, с вашей малой помощью он продолжит движение. In order not to trample the land just processed, turn the handle and go next to the plowed strip.
When working as a cultivator on wet land, large clods are obtained. The soil is then difficult to loosen, and the earth sticks to cutters. When the earth is very dry, the depth of processing is sharply reduced. In this case, they pass the strip first at a low depth, repeating its passage to the necessary. Therefore, it is best to work with moderately wet soil. The low speed of the cultivator at high turns of the cutter allows you to more carefully process the soil.
Когда земля мягкая, для рыхления почвы лучше всего подойдет насадка в виде якоря. It is more convenient to move in rows or zigzags with a cultivator.
Some tips on how to handle the cultivator correctly
If there are many small pebbles on the site, work at lower speeds. The same.based tractor will serve for a long time provided that the maintenance of the maintenance. Oil replacement, cleaning the unit, sharpening milling. the key to the “health” of your cultivator. Cannot be saved in oil. When pouring non.suitable oil in the process, a solid sediment is formed, which clogs the unit nodes. As a result, the cultivator may fail. And then the costs of its repair will significantly exceed the savings that you managed to achieve on the change of oil
Important: you can fill in fuel only with a stopped and cooled engine. After refueling, check the tightness of the fuel tank. All settings should also be carried out with the engine turned off. If you feel the vibration during work, this is a signal about the problems that have begun
It is worth stopping the engine, finding the cause (most likely weakened the mounting of the parts) and eliminate it. A row in the garden is not always perfect. In order not to damage plants, you can reduce the cultivation strip, removing external mills. Powerful motor cultivators can move not only forward, but also backward. If necessary, change the direction of movement, withstand the pause until the milling stops. The cultivator must move smoothly and evenly. If it buries into the ground, then it is necessary to adjust the position of the wheels or change the mills in places. After using the unit, wipe all its metal parts with a rag. If necessary, rinse the mills followed by wiping dry. Security measures while working with a cultivator
- Do not trust children with a cultivator management.
- Do not allow people who are not familiar with the rules of handling him.
- Make sure that there are no other people or animals near a working unit.
- Follow the safe distance to rotating elements.
- Use special strong clothes, shoes and gloves. Laces, ribbons, floors of clothing. nothing should hang out when moving.
Pachot of a motor block with a plow
Experienced experts advise novice gardeners their work on plowing to start with stretching the cord along the first row. Such a simple procedure will make the furrow even.
By plowing other rows, the wheel of a motor block will pass along the finished furrow of the first row. For this reason, all other furrows will turn out to be even, additional measures are not required.
In order to plow the garden was convenient, the procedure must be carried out along a long row. This will help get rid of additional efforts.
Plug adjustment
The quality of plowing will not be worthy if the plow is adjusted incorrectly. To ensure normal work, it is necessary:
- The mini.tractor needs to be raised a little above the ground. You can achieve this by choosing small stands 15 cm high (boards or bricks). The greater the necessary depth of soil plowing, the higher the stands should be: if the operation is carried out in the fall, the height of the stands is made 20-25 cm. In spring, the height is left less-10-20 cm.
- Install the hitch without deviating from the instructions of equipment manufacturers. The edge of the Lemech should be in contact with the ground completely, while the plow rack must be installed vertically, and the riddle should be horizontally.
- Turning the handle at the base of the walk.behind tractor to the left, you can process the not yet plowed strip. This will also help to avoid the migration of the car. When turning the unit, it is necessary to try to ensure that its right wheel remains opposite the finished furrow.
The depth of plowing
To achieve the desired depth of a plow, you need to pay attention to the weight of the walk.behind tractor. It is better to choose the one that is harder
You can add weights on your own by clinging additional goods to the wheels.
The first furrow is made with a depth of no more than 10 cm. You need to plow it in a hurry and without pressing on the car. If it happened that the equipment has overheated, it is turned off for half an hour.
With relatively soft soil, a metal knife goes into the ground at a distance of a shovel bayonet. If the earth is more solid, it is difficult to achieve such a depth the first time. Therefore, the operation of plowing is carried out in two or even several receptions, each time lowering the plow deeper.
Very hard soil is easier to plow with a motor block in a wet state.
Plowing plow
The main plow should begin only after the trial option is completed and all the shortcomings are taken into account.
Two neighboring plowed stripes should be obtained with an interval not exceeding 10 cm from each other. Neighboring furrows should not fall asleep with the soil one another. The right wheel of the car should pass in the middle of the dump of the already finished furrow, and not on its basis.
Slightly increasing speed, it can be achieved that the surface of the plowing will become smoother, without lumps. The plow makes it possible to make the depth of the furrows 15-20 cm.
With qualitatively, plowed the soil with a motor block thanks to the speed mode. It is best when the one.axle tractor has several programs so that the owner can choose the most convenient for himself.
Instructions: how to plow a motor block with a plow
Now that the unoic tractor is ready for soil plowing, soil hooks on the spot, we move on to installing a hinged plow on a single tractor:
We fasten the plow with the clutch device, while the fasteners do not tighten completely so that you can subsequently adjust the plow.
We fasten the clutch with the plow and the mounting earring of the walk.behind tractor using two pins. Everything, the plow is installed on a single tractor and now you can proceed to its adjustment (photo).
In contrast to preparing a motor block and installing the plow, adjusting the plow is slightly more complicated and should be performed efficiently, since if the plow is improperly adjusting the plow of the earth will take a lot of effort and time from you, and, unfortunately, the quality of the plow will leave the best.
Adjustment of the motoroblock plow
- one. First, substitute for the uniform tractor stands, which should be specially prepared for this.
- Put the ground hooks of the walk.behind tractor on the stands, and bring the same stand under the supporting leg of the walk.behind tractor so that it does not lean towards the plow, that is, you need to balance the uniform tractor with a plow on the stands.
- 2. The height of the stands for soil hooks is determined by the soil plowing with the depth of the soil: if plowing before winter, then the height of the stands should be up to 20-25 cm, if you are going to plow in the spring, then the height of the stands is smaller-10-20 cm.
- 3. After the uniform tractor from balanced, using the adjusting bolts, set the plow body so that its heel is parallel to the earth.
- Photo 4 shows a properly adjusted plow with a heel parallel to the surface of the earth.
- four. Next, remove the one.axle tractor from the stands, put the drive so that the control handles are at the level of the belt.This position drove a motor block during operation does not load her hands and they do not get tired for a long time when. When all the plug adjustment operations are performed, you can proceed to the plow.
Before the start of the main soil plowing, perform a control plow and evaluate whether the plow is correctly adjusted, what is the quality of the soil dump and what is the depth of the furrow.
The comb of the subsequent furrow should lie close to the crest of the previous furrow, that is, between them (crests) should not be more than 10 cm of distance.Also, the subsequent groove should not lie on the previous groove with soil bulk. In order for this to work out, the right wheel of the walk.behind tractor needs to go not at the base of the previous furrow, but in the middle of its dump (the previous furrow).
How to plow a plow on a walk.behind tract, recommendations
Motoblocks to many owners of personal plots and gardens facilitate manual labor. The same tractor, with its proper operation, will become an indispensable assistant in your farm. But not everyone knows how to plow a plow on a walk.behind.
Rather, they do not know how to properly prepare a single tractor and a plow for plowing and cultivating the earth. But, it’s not so difficult. Study our recommendations, and you will succeed.
First of all, depending on the size of the processed area, you need to choose the appropriate one.axle tractor and a plowing gun. All motoblocks are divided into three types:
- one. Light motoblocks or motor.cultivators with a weight usually not exceeding fifty kilograms. The power of the motor.cultivator is from three to five horsepower. Intended for cultivation of land using a cultivator or cutter. The area of the processed site is up to six acres.
- 2. Medium motoblocks with a capacity of up to twelve horsepower and weighing up to one hundred kilograms. Processing areas up to twenty acres using a cultivator or light plow.
- 3. Heavy motoblocks with a capacity of up to thirty horsepower and processing area up to two hectares, usually using a hinged plow.
Now that when we have decided on the walk.behind tractor, we will find out how to plow a motor block correctly. Small areas are best processed using a cultivator or cutter. The supply of light and medium.sized walk.as shoes includes with milling.
Soil plowing technology with their help is simple. It is simply a single tractor is placed on the edge of the site, an increased gear is turned on and, holding it, we follow it, turning 180 degrees at the opposite end of the site.
A completely different thing to plow with a plow in a large area. The correct adjustment of the plow is very important here. Suppose it is done correctly.
Then, at low speed, a control pass is made from one to the other edge of the site, on which we unfold one.axle tractor and perform the reverse passage. At the same time, we put the one.based tractor with the right wheel in the middle of the furrow, which remained from the first passage. We carefully observe the plow. Taking into account the inclination of the walk.behind tractor, the plow should stand perpendicular to the plane of the earth. If this is not, then adjust the plow again.
Then the second passage is made and the depth of the furrow is evaluated. If the depth is too large or too small, then adjust the plow. As a rule, with plow plowing, the depth of the grooves should be within 15-20 centimeters.
As the plowing is mastering, when your furrows become even, you can raise the speed of the walk.behind tractor. Then the plow will dump the ground stronger, its surface will be even, without lumps, and the plowing itself will go faster. That’s how they plow with motorcels.
In order for the work with the walk.behind tractor to be easy, and soil processing is effective, it is necessary to follow a number of simple recommendations.
- Areas up to 6 acres in size is best processed using cultivators. But if it is decided to use the one.axle tractor, then instead of a plow, saber.shaped or noodles should be placed.
- It is recommended to use a hinged plow for plowing fields with an area of more than 1 ha. However, the edges of the sites and places with complex geometry are also better to treat with milling.
- In the process, it is necessary to carefully monitor the condition of the equipment and prevent oil from the transmission. Otherwise, the harmful fluid will fall into the treated soil and cause its partial pollution.
- When plowing virgin lands, as well as in the processing of rocky and clay soils, it is necessary to use weighting. Otherwise, the risk of the one.based tractor will begin to jump along the virgin lands and a deep plow will require great effort.
- When using milling plants, it is recommended to equip their ends with protective disks. This will reduce the likelihood of cultivating adjacent lands and will allow plowing strictly along the boundaries of the site.
- To reduce the load on the ear, it is necessary to use special headphones or berushi, and for partial neutralization of vibration, mittens should be put on. In addition, when performing plowing, it is necessary to move from the leeward side, which will reduce the harmful effects of the exhaust gases. If you have to plow in a large greenhouse, then good ventilation of the room should be ensured. To do this, open all windows and doors, as well as periodically jerk off the engine and ventilate the greenhouse.
1950’s Ferguson TO-30 Tractor Movie The Ferguson System Works For You
- The refueling of the fuel tank, as well as the replacement of the engine oil, should be carried out only with a broken engine. At the same time, it is advisable to pass fuel through a funnel with a special filter.
- It is strictly forbidden to operate a single.axle tractor near open fire and wipe it with a rag moistened in gasoline.
The plowing of the site with a walk.behind tractor helps to greatly facilitate the process of soil processing, improves the general condition of the soil, increases productivity and significantly reduces the time of work.
About the plow of the earth with a motor block, watch in the video below.
Correct plowing of the Earth with a motorcycle unit
Before plowing, wheels are hung with a diameter of 50-60 cm and 18-20 cm wide. It is important to observe these parameters if the wheels are too narrow, there is a chance that the tool will wind from side to side. Not enough diameter will create a small distance between the soil and the gearbox. If the rim is continuous, the likelihood increases that the Earth will gather in the ribs-groups.
For hinging equipment you will need a partner. It will help raise the equipment and put it on stands, to the recommended height of 15-20 cm. At the same time, the edge of the lime should touch the earth. The plow stand is located vertically, and the riddle is installed in a horizontal position. The right edge is installed on the line with the inner edge of the right wheel. This provides an even pruning of the earth, a light dump and a smooth course of the walk.behind tractor. Before conducting operations, you should cheer with the manufacturer’s instructions.
Preparation of soil
A cord is pulled along the ground, which serves as a guideline for further movement. Usually it is installed on the first row. These rules help in inexperienced plowmen to observe the guideline, since the plow takes aside. On the second row, the cord is removed. As a rule, a person who has already engaged in such types of work has no problems with maintaining the necessary distances and makes all rows even.
Working with a land plot
After preliminary preparation, plowing begins. For a smaller number of unnecessary movements, the one.axic tractor goes along the side that is larger. This allows you to make fewer turns, which saves both the employee’s forces and the time spent on overwriting the direction of the block. The handle turns to the left for simplicity. It is important to observe the moderate pace of movement of the block in order to prevent the motor. In case of overheating, the work is suspended until the moment the block cooled. It is also not recommended to push the plow.
Each field is unique and has different soil hardness. Loogging is considered normal to the quality of the soil, in which the earth is easily pierced with a metal stick to a depth of 50 cm. The solid ground makes it difficult to move the plowing machine and negatively affects the serviceability and further performance of the tool. In this case, the soil is moistened with ordinary water or special solutions, and the plot is held twice. The first is preparatory, and the second is used for plowing to full depth. In some cases, you should fix the result and go through the third time.
How to plow a motor block with milling cutters correctly
The appearance of milling plants for motoblocks has greatly simplified the procedure for cultivating land for many gardeners. Instead of traditional works, such as plowing and harrowing, a comprehensive operation has appeared, which allows you to get a loose soil structure 1 time suitable for sowing work. This significantly reduced labor costs and gave a significant winning time.
Attention! The essence of the method of milling of the soil is to use special metal mills as a working body and movement. Each milling cutter consists of several metal blades fixed on the rotation axis of the wheelchass wheel.
How to adjust the depth of plowing with a motor block with milling
The maximum depth of cultivation by a motorcycle unit (it is more correct to call the process of plowing with cutters) to the greatest extent depends on the diameter of the cutter and usually half of this value. Attempts to plow to a great depth will lead to the fact that the cultivator will simply be overwhelmed. Adjust the deepening to the soil within the required limits using a coupon.
Important! If even on a small deepening, the cultivator is drowning (buries into the ground), it is recommended to increase the amount of milling.
How to dig a garden with a motor block with milling
The standard process of cultivation of the Earth by a motor block is usually carried out in 2 stages.
- Install a couch on a small deepening. They process the plot throughout the area, bypassing it in a circle and gradually shifting to the center. At the same time, the cultivator works at small speeds or in the first gear.
- Set a couch to the required depth of cultivation. The site is processed over the entire area at high speeds or at 2 speeds.
As a rule, to dig a previously processed area by a motor block, 2 passes are enough.
Warning! For heavy soil, an intermediate passage may be required, while the couch is installed by half the required depth.
How to plow the virgin soil with a motoblock with milling
The virgin soil plowing with cutters with cutters is carried out in several techniques. The first passage at low speed with minimal deepening violates the integrity of the turf, destroys the strongest surface layer. On the second and subsequent passages, the deepening is increased, gradually increase the engine speed. In total, 3-4 processing may be required, it is highly dependent on the density and structure of the soil.
Important clarifications
The plowing plowing by the motor block occurs vertically, when it begins to deviate, the farmer with the help of its own forces redirects in the right direction and further monitors the correct movement of the tool. To facilitate this task in the adjusting groove, nuts are weakened, and at the end they are tightened again. Often, motoblocks are used to hill potatoes, for which another attachment equipment is clinging to. cupcach. He cuts the ground to the same depth as the plow. There are two types: ordinary and disk. convenient to use. discs, but it is much more expensive.
The same.based tractor is known as a convenient harvesting tool. Instead of the cigarette lights or plow, an object is hung, which is a mixture of right paws and grilles. His work lies in the fact that he lifts the ground, takes the root crops and back the soil in such a way that the harvested crop remains on the surface.
How to plow a plow on a walk.behind tract, recommendations
Motoblocks to many owners of personal plots and gardens facilitate manual labor. The same tractor, with its proper operation, will become an indispensable assistant in your farm. But not everyone knows how to plow a plow on a walk.behind.
Rather, they do not know how to properly prepare a single tractor and a plow for plowing and cultivating the earth. But, it’s not so difficult. Study our recommendations, and you will succeed.
First of all, depending on the size of the processed area, you need to choose the appropriate one.axle tractor and a plowing gun. All motoblocks are divided into three types:
- one. Light motoblocks or motor.cultivators with a weight usually not exceeding fifty kilograms. The power of the motor.cultivator is from three to five horsepower. Intended for cultivation of land using a cultivator or cutter. The area of the processed site is up to six acres.
- 2. Medium motoblocks with a capacity of up to twelve horsepower and weighing up to one hundred kilograms. They process areas up to twenty hundredths using a cultivator or light plow.
- 3. Heavy motoblocks with a capacity of up to thirty horsepower and processing area up to two hectares, usually using a hinged plow.
Now that when we have decided on the walk.behind tractor, we will find out how to plow a motor block correctly. Small areas are best processed using a cultivator or cutter. The supply of light and medium.sized walk.as shoes includes with milling.
Soil plowing technology with their help is simple. It is simply a single tractor is placed on the edge of the site, an increased gear is turned on and, holding it, we follow it, turning 180 degrees at the opposite end of the site.
A completely different thing to plow with a plow in a large area. The correct adjustment of the plow is very important here. Suppose it is done correctly.
Then, at low speed, a control pass is made from one to the other edge of the site, on which we unfold one.axle tractor and perform the reverse passage. At the same time, we put the one.based tractor with the right wheel in the middle of the furrow, which remained from the first passage. We carefully observe the plow. Taking into account the inclination of the walk.behind tractor, the plow should stand perpendicular to the plane of the earth. If this is not, then adjust the plow again.
Then the second passage is made and the depth of the furrow is evaluated. If the depth is too large or too small, then adjust the plow. As a rule, with plow plowing, the depth of the grooves should be within 15-20 centimeters.
HOW TO MAKE A CULTIVATE ROTARY TILLER WEEDER
As the plowing is mastering, when your furrows become even, you can raise the speed of the walk.behind tractor. Then the plow will dump the ground stronger, its surface will be even, without lumps, and the plowing itself will go faster. That’s how they plow with motorcels.
Earth plowing with a motor block with an adapter
The quality of plowing and its convenience can be increased if you turn the plow into a transport and frontal module. To do this, it is attached to the adapter frame, not a walk.behind tractor. This type of plowing is lighter and safer, but less maneuverable. The speed of work can be increased from 5 to 10 km/h.
Adapter. a trailer for a walk.behind tractor or mini.cutter from a walk.behind tractor. The functionality of such an unit can be compared with the capabilities of the tractor. The range of tasks increases depending on the attachment equipment.
Some models have a lever used to rise. This makes control of the mechanism more simple and makes it possible to move it around the site.
Alignment of the site using a motor block and cultivator
This type of equipment is suitable not only for agricultural needs. Cultivator or Unine tractor can be used for landscape work. You can align the summer cottage with improvised means, shovel and rakes, as well as with the help of utility equipment, but if the area is hilly or replete with stumps and a developed root system, a more heavy equipment may be required.
The alignment of the site with a cultivator is possible only if there are minor irregularities that can be eliminated without resorting to additional technical means (a tractor with a bucket, etc.D.). The same-based tractor is capable of immersing a little deeper, but on average, the immersion area reaches 15-17 cm. Further leveling of the site occurs with the help of a rake. Loosened soil should be evenly distributed throughout the site.
If the soil on the site is too hard, rocky, or if there are undecuted stumps and t.D., It will be better to resort to the service of the tractor. Solid items, such as a large stone, deepened into the soil for a considerable distance, or an overgrown rosehip bush, deeply rooted on the site, it will be better to dig in advance using a conventional bayonet shovel. Only by removing the parts interfering with loosening and removing large garbage, you can start work with a walk.behind tractor.
It is important to remember that the operation of a motor block and a cultivator on hilly terrain and other irregularities are associated with increased risk.
Mowing grass with a walk.behind tractor
The same.based tractor can help when harvesting hay. To do this, it is not necessary to get an old tool from the barn and go to the haymaking, it is enough to use the appropriate nozzles. Most often, a mower is a basic nozzle that comes with. The mowing process itself should not cause complaints, it is enough to carefully study the instructions and properly prepare the device for operation.
The main problems when working with a mowing are the dull blades-noles and a belt-drive scroll. It will be enough to remove the knives, clean and sharpen. The belt must be examined visually and, if the weakening is noticeable to the eye, just slightly tighten to normal, using the “native” hexagon. Since the unoic tractor during operation works at high speeds, some bolts may weaken. Because of this, hum and vibrations may occur. To solve this problem, it will be enough just to draw all the mounts “in a circle”.
The better to mow, a walk.behind engineer or a lawn mower, the user decides. The gasoline trimmer for the grass is mobile, but makes a lot of noise, in addition, it requires constant valve of fuel and control of combustible materials. The trimmer is an ethletric for grass is ineffective in the field where there is nowhere to stick out the outlet, and it is where, most often, haymaking is carried out. The same.based tractor may be completely useless in conditions of limited space.
Tips and recommendations
The first and most importantly, what should be noted. observe safety precautions.
In general, the device of the walk.behind tractor is understandable and simple. But in any case, as well as for any other equipment, it needs care and timely maintenance and replacement of consumables. Use only high.quality spare parts recommended by manufacturers.
To prevent mixing of the fertile layer and what is under it, change the direction of plowing every season. In this case, you will reduce the likelihood of crop failure.
If your plow is not provided for height adjustment, you can independently drill an additional hole in the rack. But make sure that the design does not lose its rigidity.
The device of the revolutionary plow to the walk.behind tractor
Consider the device of the revolutionary plow to the walk.behind tractor on a specific example. The plow is designed for cringing and turning the arable layer, and is recommended for use on soils that have already been processed.
The main characteristics of the plow
- Plowing depth 20cm;
- Lemech width (capture) 22 cm;
- 3 holes are made in the rack to configure the depth of plowing in the rack;
- Height 76 cm;
- Width 32 cm;
- Length 48 cm;
The plow joins the walk.behind tractor using the appropriate adhesion. The plow should be adjusted so that the side line of the field board during operation is located in parallel to the direction of movement, t.E along the wall of the furrow. And the supporting triangle formed by the cutting edge of the bowl, the heel and the lower facet of the field board, should be in the horizontal plane.
In order to configure the depth of plowing, you need to adjust the angle of inclination of the plow body in the vertical-proper plane. To do this, use additional holes in the staple of the miniseter and the plow rack, or the adjustment screw of the clutch.
During operation, you can adjust the correct installation of the plow. The design of this revolutionary plow allows you to fall off the soil layer in one direction, both with direct and in the reverse course. To change the housing of the revolutionary plow, it is enough to turn it 180 ° around the axis, and fix it in the working position. Before you start working with a plow, you need to equip it with soil.bearing, to ensure a reliable adhesion of the assembly of the unit with processed soil.
Safety precautions when working with a revolutionary plow
Before starting work, check whether all threaded connections are tightened. Delete all extraneous objects from the processed territory. During the maneuvering of the unit with a plow installed, as well as when moving in reverse, observe special caution. In order to avoid injuries that can be obtained from protruding sharp corners and edges, follow a safe distance to the gun during operation.
Use protective gloves when servicing the gun. If you finished work, you need to clean the plow. All details and threaded joints that do not have a paintwork must be treated with grease. Store the plow must be in a closed room.