Replacing the rotor on REBIR electric saw. How to sharpen a chain yourself

Repair of the main malfunctions of the chain electric saw

Electric chain saw is an indispensable tool for owners of private houses and cottages. It can be cut off the branches in the garden, cut down trees, cut boards and other materials on wood.based. But no matter how expensive and reliable this unit was, the moment will come when small or large malfunctions will appear in it. Of course, serious breakdowns should be eliminated only in the service center. But minor repair of a chain electric saw can most often be performed with your own hand.

The device of the chain electric saw differs from the device of the chainsaw only with the type of drive, namely the presence of an electric motor instead of a gasoline engine. The unit is made of an electric motor placed in a plastic case, a lubricant tank, an oil pump, as well as from a tire and a chain that has cutting elements (teeth). How the electric chain saw is arranged, you can consider in the figure below.

Electric saws can be either with the transverse location of the engine (shown in the figure above) and with longitudinal (see. photo below).

In an electric saw with a transverse location of the engine, the rotational movement from it to the leading star is transmitted directly. In an apparatus with a longitudinally located electric motor, this process is carried out through a gearbox.

Asterisk installed in the same plane with the unit bus, rotating, pulls the chain. The latter installed on the tire of the unit glides over it at high speed. Due to the presence of cutting elements on the chain, the wood is sawing. Since the canvas from the electric saw has a large width than the tire, the tool does not jam in the material, and the sawing process occurs quickly.

To reduce the wear of the saw chain and tires on the electric saws, a lubricant system is installed, which supplies oil to the saw headset.

The lubricant system includes an oil tank with a volume of about 500 ml and an oil pump. The latter during the operation of the electric saw continuously supplies lubrication on the tire. Further, the lubricant spreads with the help of the chain over the entire surface of the tire and falls on both the lead and the guide stars.

The main malfunctions of electric saw

Breakdown of an electric chain saw do not occur from scratch. Most often, they can appear due to voltage jumps in the network, improper operation of the unit, poor quality assembly quality of the device. The main malfunctions of chain electric saws can be attributed to the following.

• When pressing the button for starting the unit, the saw is not started. Perhaps the network cable or electric fork of the device has failed. If everything is in order with the cable, then the reason for the failure of the unit may be a faulty start button, burning out the engine windings or complete wear of the brushes.
• During operation, brushes on the electric saw are burning, and there is a circular fire on the engine manifold. The malfunction can be caused by worn.out brushes or closing the anchor winding.
• The chain does not enter the lubricant. This happens if the oil ended in the tank, the tube or hole responsible for the supply of lubrication was closed, or the oil pump was out of order.
• The unit cannot develop full power. The possible reasons are as follows: brushes have worn out; Interpreter closure or breakage of the anchor winding; low voltage in the network; The start button failed; jamming in the gearbox occurred; Brake system malfunction.
• The engine engine stops during operation. This behavior of the unit can be caused by jamming the gearbox or wear of the brushes.
• The electric motor of the device quickly overheats. The reasons that the saw heats up can be several: high ambient temperature; poor engine ventilation when working at low speeds; holes intended for ventilation are blocked or clogged; prolonged operation of the unit under a large load; increased pace of work by the device without breaks to rest; gearal malfunction; lubrication failure; Damage to the motor windings.
• The unit makes an uneven drink. The reason for this may be the dull cuts of the chain or uneven wear of the tire.
• When operating the motor, the chain remains motionless. Most often breakdown occurs due to the failure of the clutch. Also, this malfunction can occur during a breakdown of the gear of the gearbox and a drive asterisk.

Rebir drank circular Rebir IE 5107G2 IE 5107G2

Pros: you can fix the saw up the disk to the table, the bench to the workbench is mounted in the kit.

Comment: good Internet, survived the winter in the garage. It works without complaints.

Pros: simple and reliable design. Good equipment

Pros: excellent disk saw worked for me, it has changed the anchor still works as well as

Comment: I want to buy Bosch 1400 watts 190 circle I really like it

Rebir reviews of the circular saw Rebir IE 5107G2 IE 5107G2

Information in the description of the model is reference character. Always specify the characteristics and completion of the product from the manager of your chosen online store before buying.

General characteristics

The husband appreciated the saw “excellent”. Made a special table for her. Working disk of good quality, saws both wood and OSB, plywood, laminated wood-piece plate

Review: I did not like that everything is some kind of flimsy.When buying on the site in the description, a country of production of Latvia was written.Price 7900.How everything was designed the next day in the description of the country of production China price 10990.When ordering I knew that it was China.But probably Chinese goods are better than produced in Latvia.))) in the photo of the factory marriage of a plastic handle

Sufficient power for most homework, the depth of drank, including at an angle. The delivery kit includes everything that is necessary for work “out of the box”: saw disk, clamps, keys, stops (stands).

-: Flimsy stamped sawing platform in circular saw mode. Generally noisy and vibrating machine. A flimsy longitudinal guide, which during the first installation on the saw must be stipulated to the required geometry. Regarding the plane of the disk, non.parallelism both along the drink and in the vertical plane. When installing plastic racks included in the kit (which the manufacturer involves screw with self.tapping screws to the table), the main basic surface of the casing is obtained with a gap relative to the table. It is impossible to fasten the existing clamps without distortion, or without “footcloths”. The clamps themselves compared to old whole.lit ones (from Rebira approximately 2006) are uncomfortable. The bar closing the hole in the table and the fixing protective casing of the curve, and its board constantly touches and sticks right at the entrance in front of the saw. I had to finalize a pair of hammer blows. The complete key for replacing the disk did not understand how to use it, t.to. Two pins on the key are much already located than the openings on the puck. It is how to use the key to a small corner grinder on a large. You catch to one tooth and to the edge of the washer. Maybe it’s just unlucky.

Review: for work as a portable parquet is heavy. It was bought in August 2020 precisely as a decision “to the table” and, if necessary, transferred anywhere and cut the epaulets in the version of the circular. A similar car was already on the farm, so I did not hesitate for a long time. In this case, you can forgive everything only because it works, works, works. Therefore, 4 stars. I will work-full.

Dismantling of the tool

Almost all malfunctions of electrical disk saws cannot be eliminated without disassembling the device partially or completely. Full disassembly of a hand.based electrical saw using the Interskol unit is performed in the following order.

On this, the full disassembly of the disk saw ends.

Do.it.yourself disk saw repair

When starting to repair the unit with your own hands, it is not necessary to disassemble it completely to clarify the reasons for the breakdown. Some malfunctions are characterized by specific symptoms by which you can determine the problem and already purposefully disassemble this or that part of the device.

The saw does not turn on

If when you press the start button, the engine of the unit “is silent”, then the first thing to focus on is the network cable, provided that there is electricity in the outlet (connect the device to another outlet for verification).

Advice! Before checking the cable, you need to disassemble the electric fork and make sure that the cord conductors are connected to its pins.

To check the electric cable, you need to disconnect the handle. This will help to get to the contacts to which the wires of the network cord are soldered. Further, with the help of a tester, call each wire, pressing one probe to the soldered contact, and the second. to the pin of the fork.

If the network cable is intact, then in search of a malfunction do the following.

• Blind the entire chain by the tester, starting from the cable entrance to the unit to the launch button. You should also check the contacts of the button at its input and output with the key pressed. In normal condition, the torn chain should be closed. Call all the wires after the button going to the engine brushes.
• If everything is in order with the conductors, check how much the electrodes of the brushes have worn out. After wear of the electrode 2/3 of the initial size, it should be replaced. Brushes, regardless of how much each of them has worn out, change in pairs.
• If the brushes are in good condition, then, most likely, the engine has failed. In his windings, a cliff or inter.flip.circuit could occur. In this case, it is better to entrust the engine repair to specialists who will rewind the stator coils or anchor.

The engine heats up

The unit can heat up excessively, for example, with its intensive use, as well as when sawing hard wood or the use of a saw disk with a large number of teeth, when the load on the engine increases significantly. Also caused by overheating of the malfunctioning motor associated with the windows of the stator and anchor, which are eliminated only in the service center.

Brushes are burning

Strong sparking from under the brushes is caused by excessive wear, when the spring can no longer press the electrodes to the collector with the required force. To replace the brushes, you need to disconnect the engine cover or remove them through special holes in the engine housing (depending on the power plant model).

Jammed the shaft during operation

This malfunction may happen when for any reason, a stopper is pressed during the tool. It is designed to fix the shaft when replacing equipment and should be used after a complete stop of the engine. Otherwise, the Stop Stop rod breaks down, and its debris fall into the engine, causing jamming. There are frequent cases when this leads to deformation of the anchor shaft. Also, the consequence of pressing on the stopper can be the split of the gearbox body, the fragments of which can damage the gears and provoke their jamming. To solve the problem, you will need to replace the anchor, a stopper leading (large) gear of the gearbox and its body.

In some cases, the gearbox can jam with the complete destruction of the bearing.

The saw stops in the process

The engine stops in most cases cause a cavity worn electrical brushes. Когда контакт между электродом щетки и ламелями коллектора нарушается, происходит выключение агрегата.

Often, when buying brushes for a given apparatus, products with a short conductor connecting the electrode to the plate come across. This conductor is located inside the spring and does not allow it to be completely imprisoned. Когда электрод изнашивается до определенной длины, то прижим его к коллектору прекращается, поскольку этому препятствует короткий проводник. If you, examining the brush, find that it is not yet worn out and the spring is not unclenched, then the part should be replaced.

The gearbox body is very hot

The rapid heating of the gearbox occurs if the shaft bearing is unusable, on which the gear is fixed and the equipment is attached. In this case, in addition to heating, you can replace the appearance of extraneous noises in this unit node. It is necessary to disassemble the gearbox and change the bearing. The gearbox will also heat up if it is not enough lubricant or it is completely absent.

Advice! Periodically, you should disassemble the gearbox and check the presence of lubrication. If necessary, refill with lubrication the internal space of the node. For these purposes, you can use a special lubricant for gearboxes of corner grinder.

The saw does not gain power

If during the use of the unit you noticed a drop in its power, then it is first recommended to check the voltage level in the network. Sometimes even a slight drop can negatively affect the power of the power tool.

Also, loss of power can be observed with wear of the bearings of the anchor or gearbox bearing. In this case, extraneous noises will be heard, previously not characteristic of this unit. By their localization, you can determine where the problem bearing is located. in the gearbox or engine. To replace bearings, you will need to disassemble the disk saw. How to do this was described above.

If during the operation of the unit is not heard, the engine still poorly develops momentum and power, then pay attention to its collector. Usually on it you can see a circular spark (fire ring). This can happen due to the inter-flip closing of the anchor coil or the accumulation of dirt between the collector lamps.

Expand the engine housing and carefully inspect the collector (the place where the electrodes of the brushes glide). It consists of parallel stripes (lamellas). There is a small gap between them. When this gap is clogged with conductive graphite dust formed during the wear of the brushes, a short circuit occurs between the lamels, and a burning ring around them appears.

How to identify a malfunction of the brush node

Brushes that are a consumable element come out of the system. The brushes are made of graphite, and with their help the current is transferred to the rotor through the collector node. In the process, the brushes abrupt, burn out, wear out and require replacement. The resource of the brushes depends on different factors:

You can identify a fault of brushes according to such a basis as excessive sparking. If, before the drill has ceased to be launched, its excessive sparking with signs of soot was observed, then with a high degree of probability it is necessary to replace coal brushes. To replace it, it is necessary to extract elements from the brush holders, pull out the worn.out parts and establish new.

It is interesting! If the wear of the brushes is more than 60% of the initial length, then they must be replaced.

In addition to a malfunction of the brushes, it is necessary to pay attention to the condition of the copper lamella of the collector. If there are signs of soot on a copper basis, as well as chips and other defects, then all this should be eliminated

If you cannot eliminate it yourself, then the anchor should be replaced. The causes of soot on copper plates are excessive sparking of the power tool. In addition, with a strong wear of the collector, a connection (closure) of the plates arises among themselves, which is also unacceptable.

Visual examination of the tool

There are often situations when the tool still works, but not as it should be. And in 30 % of cases the fault of the burnt anchor. This can be identified visually, even before the opening of the body.

The indirect signs of the “tired” anchor of the electric motor are such problems:

When the electric motor is visible, a very strong sparking on the collector is visible.

When trying to launch a corner grinder (drill, disc saw, etc.) There is a rigid voltage subsidence (lighting blinks).

The launch of the electric motor is accompanied by sharp jerks.

A characteristic smell of burning wiring is heard from the body.

The tool does not gain the same power.

Please note that most of these signs can also indicate the banal wear of the electric motor brushes. If they were erased or crushed, then the anchor, most likely, had nothing to do with

We change it to new ones, clean the collector from the graphite raid, and calmly work on. If the brushes look intact, and the above symptoms are observed, with a 80 percent probability, it can be argued that the problem is in the anchor of the electric motor.

If the power tool does not show signs of life at all, there may be much more reasons, and not only an anchor check will be needed.

Visual examination of the tool

There are often situations when the tool still works, but not as it should be. And in 30 % of cases the fault of the burnt anchor. This can be identified visually, even before the opening of the body.

The indirect signs of the “tired” anchor of the electric motor are such problems:

When the electric motor is visible, a very strong sparking on the collector is visible.

When trying to launch a corner grinder (drill, disc saw, etc.) There is a rigid voltage subsidence (lighting blinks).

The launch of the electric motor is accompanied by sharp jerks.

A characteristic smell of burning wiring is heard from the body.

The tool does not gain the same power.

Please note that most of these signs can also indicate the banal wear of the electric motor brushes. If they were erased or crushed, then the anchor, most likely, had nothing to do with

We change it to new ones, clean the collector from the graphite raid, and calmly work on. If the brushes look intact, and the above symptoms are observed, with a 80 percent probability, it can be argued that the problem is in the anchor of the electric motor.

If the power tool does not show signs of life at all, there may be much more reasons, and not only an anchor check will be needed.

Possible reasons

Factors causing the stator failure:

Signs by which you can understand that the stator is faulty:

• The smell of burning insulation appears.
• The case overheats.
• Smoke appears.
• The rotation of the shaft slows down or stops.
• The shaft spontaneously spontaneously spaces, the tool is dramatically gaining maximum speed.

The wires of the winding are covered with a protective layer of insulating varnish. When overheating, it burns out and destroys. This causes a short circuit of the turns. The varnish at the same time makes a specific smell. The closure of only one of the wires completely disables the corner grinder.

Rules that will help to avoid overheating of the engine angular grinder:

• Turn off the device after working at low speeds not immediately, but after about one minute.
• When working under load at low speeds, make frequent breaks.

Often you can avoid replacing a faulty stator by rewinding its winding. The rewinding of a spoiled coil of the stator of the corner grinding stator can be done with your own hands, but it is recommended to entrust this work to a specialist.

Security measures

When repairing the tool, we must not forget about security measures. First of all, you need to turn it off from the mains and do not include it on the network until the final assembly.

Work with a chain and tire is recommended to be carried out in gloves, this will protect the hands from cuts. When disassembling the screw connections, if the screw cannot be unscrewed, you need to stop making efforts and use aerosol lubricant like WD-40 this will remove the voltage and in a few minutes just unscrew the screw.

It is also worth remembering about electrical safety, it is possible to repair the parts of electrical equipment using only the face value of the parts that were originally installed.

It is optimal to use a machine sharpening of the circuit. But if there is no way to use an electric machine, then you can use the manual sharpening method using a special file and guide conductor.

The chain is put on the tire and fixed in the saw. After that, the chain stretch is made. After it is stretched, sharpening is done:

As you can see, the process of repairing a chain electric saw is not a big problem, and even those who have never been repairing power tools are quite able to. Another thing is that before starting disassembly, you need to carefully study the device of the tool and imagine all the operations that will need to be performed during repair.

Device and principle of operation of the chain electric saw

The device of the chain electric saw differs from the device of the chainsaw only with the type of drive, namely the presence of an electric motor instead of a gasoline engine. The unit is made of an electric motor placed in a plastic case, a lubricant tank, an oil pump, as well as from a tire and a chain that has cutting elements (teeth). How the electric chain saw is arranged, you can consider in the figure below.

Electric saws can be either with the transverse location of the engine (shown in the figure above) and with longitudinal (see. photo below).

In an electric saw with a transverse location of the engine, the rotational movement from it to the leading star is transmitted directly. In an apparatus with a longitudinally located electric motor, this process is carried out through a gearbox.

Asterisk installed in the same plane with the unit bus, rotating, pulls the chain. The latter installed on the tire of the unit glides over it at high speed. Due to the presence of cutting elements on the chain, the wood is sawing. Since the canvas from the electric saw has a large width than the tire, the tool does not jam in the material, and the sawing process occurs quickly.

To reduce the wear of the saw chain and tires on the electric saws, a lubricant system is installed, which supplies oil to the saw headset.

The lubricant system includes an oil tank with a volume of about 500 ml and an oil pump. The latter during operation of the electric saw continuously supplies lubrication on the tire. Further, the lubricant spreads with the help of the chain over the entire surface of the tire and falls on both the lead and the guide stars.

Recent Rebir repairs

Repaired

Repair of disk saws

Rebir RZ1-70-2

Repaired

Repair of disk saws

Rebir Rz 1 70 2

Repaired

Repair of disk saws

Rebir 5107g2

Problem: does not turn on. smooth start.

Repaired

Repair of disk saws

Rebir RZ1-70-2

repair chain of power, replacing the anchor, stator, bearings, reducer lubricants

Repaired

Repair of construction mixers

Rebir EM-1450E

Cleaning, lubricant, replacement of bearings, brushes, switch

Repaired

Repair of disk saws

Rebir IE-5107G2

Problem: stopped working, dismantled, corrected the button. I earned. now. Closes.

Replacing the electronic unit “smooth start”.

Repaired

Repair of corner grinders

Rebir LSM2-230

Repaired

Repair of electric rhubones

Rebir IE-5709B1

Repaired

Repair of electric saws

Rebir KZ1-0350

Food fixing, replacing a micro.plane.

Repaired

Repair of disk saws

Rebir IE-5107G2

Repaired

Repair of disk saws

Rebir RZ1-70-1

Problem: does not turn on. does not work.

repair buttons on, cable replacement

Repaired

Repair of electric saws

Rebir KZ1-300/350

Problem: does not work, check everything.

repair circuit of power, replacing forks, wires, repairing the power button, cleaning the brush unit.

Repaired

Repair of electric saws

Rebir KZ1-300/350

Repaired

Repair of electric rhubones

Rebir IE-5708M

Problem: When working, it is very noisy and knocks. Make it.

Cleaning, replacement of bearings, brushes, wire amplifier, food wire

Repaired

Addresses of Rebir service centers in St. Petersburg

Komendantsky pr., 4k2

On Lesnoy: Ul. Kharchenko, 12

Kupchino

Bolsheviks

Primorskaya

Civil Prospect

Kirov Plant

Lakes

Academic

Comenstatsky Prospekt

Bolsheviks

Leninsky Prospekt

Kolpino

International

On international: st. Bely Kuna, 24k1

Anchors for circulars

Anchor for the disk saw Makita 5903R DongCheng Armature length 183 mm packet diameter 54 mm collector diameter 36.5 mm Package height 50 mm Diameter of the rear bearing of 9 mm Landing the front beep of 15 mm 15 mm type Sagot 7 teeth left direction weight.

Original anchor for the Interskol DP-165/1200 Disco Rail, high quality of the goods, enhanced packet insulation, balancing

Anchor/ rotor with a fan on the Interskol DP-165/1200 disco

Replace the anchor of Makita LS1040 when: does not give the required number of revolutions;- rotation of the rotor slows down sharply; characteristic sparking and crackling is observed. If you have one of the above, then you should buy a new Makita LS1040 rotor. Danny.

Anchor (rotor) for the saw Makita (Makita) LS1040

Rotor for the circular disk saw Rebir IE-5107. The dimensions of the rotor l ~ 190 mm. D-54 mm, d collector 39.3 mm number of drive teeth 8 pieces of inclination to the right. The price is indicated for the purchase of goods on the Internet.store. In the retail store, differ from the price on the site. AT.

Anchor for the disco saw Rebir IE-5107 (8 tooth

Makita anchor for mounting detachment saw 2414NB 510240-7

Anchor (rotor) 5704R for saw Makita 5704R

Appearance, color scheme, technical characteristics of the goods and completeness may differ from real ones, check the information at the time of purchase and payment

Hitachi C 7 Mfa anchor for circular saw

Rotor (anchor) 230V for the DeWalt D25103K TYPE 10, DWEN102K TYPE 1

Anchor for angular grinder Bosch Gws 7-125, GWS 7-115, iron diameter 35mm. Iron length 42.5mm. Colenutor 24.5mm. Winged 55mm. Rear dreaming 7mm planting. Front 8mm, total rotor length 160mm

Rotor– anchor for angular grinder Bosch Bosch Gws7-125. GWS7-115

Rotor (anchor) for angular grinder (corner grinding) Metabo 7-125 IK-125

The length of the rotor, l mm159 diameter of the package (frame) of iron, d mm41 shaft (shank) 9 teeth, tilt to the right of the front bearing, d1 mm10 planting of the rear bearing, d2 mm8 distance between bearings (inside), l1 mm 128.5 length of iron package (plates)

Rotor (anchor) for disk saw Makita (Makita) 5704 R

Parameter: rotor length, l mm177 diameter of the package (frame) of iron, d mm35 shaft (shank) thread M6.5 (Step 1.25 mm) Planting the front bearing, D1 MM8 Planting the rear bearing, D2 mm7 Distance between bearings (inside), L1 mm 138 The length of the iron package (layer.

Rotor (anchor) for angular grinder (corner grinder) Bosch Gws 14-125

Anchor for the Bosch GBH 2-24 (5 teeth) anchor for Bosch GBH 2-24 (5 teeth) appearance, color scheme and completeness may differ from real ones, clarify the information at the time of purchase and payment is suitable for the Bosch GBH 2- Peorator 24 character.

Rotor (anchor) for the Bosch GBH 2-24 DSR 5 teeth

Rotor (anchor) for the Bosch GBH 2-24 DSR 6 teeth (DongCheng)

Original rotor anchor on the saw E-541A. Rotor length 215 mm iron diameter 46 mm shaft (shank) 10 mm. 8.5mm planting the front bearing, D1 9 mm Planting the rear bearing, D2 10 mm distance between the bearings (inside), 176 mm the length of the iron package (plates.

Original rotor (anchor) Baikal on the saw E-541A.

Appearance, color scheme, technical characteristics of the goods and completeness may differ from real ones, check the information at the time of purchase and payment

Replace the anchor Makita 9555NB/9554NB should be:. does not give the required number of revolutions. The rotor rotation slows down sharply. characteristic sparking and crackling is observed. If you have one of the above, then you should buy a new Makita 9 rotor 9.

Anchors for electric saw

Anchor for the disk saw Makita 5903R DongCheng Armature length 183 mm packet diameter 54 mm collector diameter 36.5 mm Package height 50 mm Diameter of the rear bearing of 9 mm Landing the front beep of 15 mm 15 mm type Sagot 7 teeth left direction weight.

Anchor Makita 9556 9557 9558 (515613-9) Original

Rotor for the circular disk saw Rebir IE-5107. The dimensions of the rotor l ~ 190 mm. D-54 mm, d collector 39.3 mm number of drive teeth 8 pieces of inclination to the right. The price is indicated for the purchase of goods on the Internet.store. In the retail store, differ from the price on the site. AT.

Anchor for the disco saw Rebir IE-5107 (8 tooth

Original anchor for the Interskol DP-165/1200 Disco Rail, high quality of the goods, enhanced packet insulation, balancing

Anchor/ rotor with a fan on the Interskol DP-165/1200 disco

Rotor (anchor) 230V for the DeWalt D25103K TYPE 10, DWEN102K TYPE 1

Replace the anchor of Makita LS1040 when: does not give the required number of revolutions;- rotation of the rotor slows down sharply; characteristic sparking and crackling is observed. If you have one of the above, then you should buy a new Makita LS1040 rotor. Danny.

Anchor (rotor) for the saw Makita (Makita) LS1040

Description L MM152 DECUMETAR PACKE (frame) of iron, d mm41av (shank) 9 teeth, tilt to the right of the front bearing, d1 mm10 the rear bearing planting, D2 mm8 distance between the bearings (inside), L1 mm 124 Length of the iron (plates) bag (plates)

Anchor for the circular saw Makita 5604R

The length of the rotor, l mm159 diameter of the package (frame) of iron, d mm41 shaft (shank) 9 teeth, tilt to the right of the front bearing, d1 mm10 planting of the rear bearing, d2 mm8 distance between bearings (inside), l1 mm 128.5 length of iron package (plates)

Rotor (anchor) for disk saw Makita (Makita) 5704 R

Anchor (rotor) 5704R for saw Makita 5704R

Appearance, color scheme, technical characteristics of the goods and completeness may differ from real ones, check the information at the time of purchase and payment

Appearance, color scheme, technical characteristics of the goods and completeness may differ from real ones, check the information at the time of purchase and payment

Appearance, color scheme, technical characteristics of the goods and completeness may differ from real ones, check the information at the time of purchase and payment

Appearance, color scheme, technical characteristics of the goods and completeness may differ from real ones, check the information at the time of purchase and payment

Anchor for chain electric saw Parma M4 Parma

Appearance, color scheme, technical characteristics of the goods and completeness may differ from real ones, check the information at the time of purchase and payment

Anchor for chain electric saw Parma M3 65 Parma

Rotor (anchor) for the disk saw Makita 5604R IK-5604

The length of the rotor is 190 mm iron diameter 54 mm shaft (shank) 7 teeth Planting the front bearing, D1 12 mm Planting of the rear bearing, D2 12 mm Distance between the bearings (inside), 143 mm Length of iron (plates)

Anchor for the disco saw Rebir IE-5107 (7 tooth

Anchor (rotor) for Interskol Electric Pilas: 1 pcs. Compatible with models: Interskol PTs16-01 length: 170 mm. Collector diameter: 28.5 mm. Collector plates length: 15 mm. Package diameter (magnetic circuit): 46 mm. Package length (magnetic circuit): 52mm. VAL diameter: 1.

Anchor Rotor for Interskol PC-16-01 Chain Electric saw AEZ

Characteristics: 7 teeth Direction: Left shaft length: 190 Planting at the collector: 10 Planting at the impeller: 12 Diameter of the collector: 36 Collector plates (working): 16 diameter of the magnetic circuit: 54 magnetic circuit length: 35 presented information about the goods, their service station.

Anchor for chain electric saw Parma Marma