Stihl 180 Stalls When Pressed On Gas
Hello, honored subscribers and readers of my blog! Online Andrey Noak. We continue the topic of chainsaws. What is needed, I already said earlier that what should be inspected in a chainsaw in order to know the cause of its malfunction. Now I’ll move on to more valuable instructions so that you do not find the cause of the difficulty for a long time and know approximately how to solve it. A chainsaw is not a very difficult tool, alas, it must be properly looked after. There are various cases when the chainsaw stalls when you press the gas, from time to time in the load, and when it does not work at idle. Let’s look at various situations together and try to find the right solution.
If you find that the tool does not start at all and stalls, then do not rush to the service center right away, of course, try to solve the problem yourself.
We check each system one by one:
- Fuel tank. You don’t have enough fuel there or it’s bad.
- Subsequent testing gets the spark plug and high voltage wire. Pay attention, the clearance of the candle normally does not exceed half mm.
- If the above items are tested and working correctly, we run to the carburetor and fuel filter. If the carburetor breaks down, contact a specialist.
When the saw dies at idle, and a frequent cause of failure is a blockage of the muffler. There is an option to simply clean it without the help of others, for this purpose you do not need the highest special.
In addition to cleaning, there is an option, however, with its help, we handle very carefully so as not to harm the internal parts of the device.
To adjust the carburetor, you need to find two bolts with the signs L and H. The latter must be turned, a little bit, only half a turn. He is responsible for the revolutions of the tool, if necessary, will raise idle.
Massive chainsaws often stall from the load. Most likely you have a clogged fuel filter, and it needs to be replaced. If this did not help, then you need to check the quality of the fuel consistency and prepare the latest.
STIHL MS 180 repair / disassembly and assembly of the carburetor / stalls at idle
Localization of problem areas:
Filters are often clogged, especially when the chainsaw is actually operated once a day. The air filter is an option to disconnect and rinse under a stream of warm water. Before sticking to the place. painstakingly dry.
If, after disconnecting the fuel hose from the carburetor with its use, no liquid flows out, it means it is clogged. It can be cleaned or replaced with a new one.
If the instrument is used frequently, a gasoline pump may fail. Each item has its own expiration date. It should be replaced as it is also called, it will contact a service center.
Horizontally, the fuel tube is located on the bottom of the tank, if the tool is tilted, the fuel will not be able to cover it one hundred percent. Specifically, this is a prerequisite that the chainsaw stops working when tilted, because the tube levitates in the air and the required amount of consistency does not reach it.
If you saw that the chainsaw is easy to start without heating, and stalls after heating. And do not start it until it cools down, then here, maybe a few troubles.
That’s all, in some places you certainly have a hose, stuffing box or gasket suction. If, inspect the muffler for carbon deposits. The third reason is the cylinder-piston group (CPG), whether there are scoring or bumps there.
From time to time, carburetor adjustments are required. Another important cause of the malfunction is the ignition coil. In cases where it burns out, the spark disappears, as it is also called, it becomes very weak, which is not enough to ignite the fuel consistency.
There are cases when the master intensively tries the engine, then to the cool, then to the hot, thereby pumping fuel. Here you need to pull yourself together, transfer the flap to the “hot start” and start the tool evenly. With all this, we slow down the speed to an almost empty level and for 40-45 seconds it warms up.
Chainsaw Stihl. Does it stall on gas? One of the reasons.
Here it is necessary to adjust the carburetor and check if there is a massive air leak.
The most common cases of chainsaw breakdowns we have already considered. It only remains to eat up that your saw will last without breakdowns. Even sturdy models like Stihl and Partner come in variations upon failure.
Do not rush to immediately run to the service center, first use my advice, so you will avoid the huge cost of money.
If the article seemed fascinating. share tips with friends through social networks. I say goodbye to you. Fortune and see you on the blog!
Stihl 180 Stalls At Full Throttle
For what reasons Stihl 180 stalls on Idling as it is also called full throttle
Although any tool is capable of breaking, the Stihl MS 180 chainsaw is no exception. Now let’s try to understand issues such as: why the chainsaw stalls with increasing speed, also on Idling in full. We will examine the options for diagnosing and eliminating defects associated with this behavior of the Stihl 180 chainsaw.
IMPORTANT. An experienced electrician has leaked the secret to the network how to pay half the price of electricity, the legal way. Read more
Why the chainsaw stalls when you press the gas
Suppose a chainsaw normally idles, but with a sharp pressure on the gas stalls. What do you like the reason for? It is immediately clear that it is not a matter of ignition (the absence of a spark), because if there was a malfunction in the ignition and the absence of a spark, the tool would simply not start. Means fuel system remains.
There are enough defects in the fuel complex of accounting programs to determine a clear premise, because of which the Stihl 180 chainsaw stalls when you press the gas, you need to carry out its full diagnosis. We advise you to read about the widespread malfunctions of the Stihl 180 chainsaw and the elimination of these defects.
Filter check
The first thing to check is the fuel filter.
Sometimes, a clogged filter is unable to pass through the fuel mixture in sufficient quantities. Accordingly, a lack of fuel appears in the system, which leads to the fact that when you press the gas on the chainsaw, the fuel burns out, and a new one does not have time to arrive under the influence of which the Stihl chainsaw stalls. Also, with a clogged fuel filter, a noticeable drop in the power of the chainsaw at the highest revolutions can be observed, but this is with minor pollution.
KEY-DOP
Air filter
On the pages of the Internet, you can easily find information that the chainsaw Stihl 180 may stall due to severe contamination of the air filter. I would like to refute this incorrect information, and say that the carburetor Stihl The MC 180 is equipped with a compensator that is designed and installed to take the air necessary for the normal operation of the Stihl 180 chainsaw, bypassing the dirty air filter. This power with a clogged air filter will fall slightly, but it certainly will not stall. Still, the power may fall due to piston wear, the Stihl MS 180 piston chainsaw will already need to be repaired.
Related posts
Carburetor
One of the circumstances because of which the chainsaw does not develop momentum when you press the gas, but rather stall, this is a carb fault. Let’s say the Stihl 180 saw worked properly, and then they put it on for a long time and did not use it. After it was started, at the same time it works perfectly at idle, and when it is pressed on the gas, it can stall. Why does it stall? The reason is a stuck carburetor valve nozzle. This, this is not 100%, however, the possibility of such a malfunction is the highest. We advise you to read an article about the device and repair of the Stihl 180 carburetor.
To be able to check the nozzle, you need to remove the carburetor and disassemble it. To remove, you need to unscrew the two nuts securing the air filter and the carburetor, then remove the air filter and the engine control lever, while disconnecting the throttle control rod from the carburetor. Next, you need to slightly pull the carburetor towards yourself, and disconnect the fuel supply hose.
KEY-DOP
It is necessary to very carefully remove the fuel hose, and prepare a plug in advance, since with its use fuel should go.
After removing the carburetor, it must be purged and cleaned of dirt, only after which the carburetor, of course, untwist.
You need to unwind the cover of the main carburetor chamber, this is the one on which the compensator is installed on top. Further when using a bolt of 8 mm and a length of two or more than 50 mm. We knock out the valve.
Stihl 180. Classics of the genre. Does not develop momentum
This is one of the problems why, saw stalls by clicking on gas chainsaw repair.
It is necessary to knock out the valve by installing the carburetor on a wooden stand, this will ensure its protection against damage to the body.
If the nozzle is removed, it can be purged using a compressor. The valve must allow air to flow in only one direction, unless of course the valve is freely blown to both states, which means it is faulty and needs to be replaced with a new one. To assemble the chainsaw when the valve is repaired, it is necessary in compliance with the reverse disassembly sequence.
You can see clearly how the carburetor is being repaired, and more precisely, how to correctly knock the valve-nozzle out of the carburetor body by watching the video.
The next common reason why a saw may stall with increasing speed, air leaks in the carburetor. You only need to check this with a special tool, but it is worth seeing that if preventive work with the carburetor has not been carried out for a long time, then of course install a new set of gaskets in the carburetor. Sometimes this helps to solve the problem with its depressurization.
Stihl 180 stalls at full throttle.
When disassembling a carburetor for replacing gaskets, it is necessary to closely examine its needle-shaped valve, press on the rocker arm and control its lifting. When, in particular, if the Stihl chainsaw has stood for a long period with fuel in the carburetor, the needle may burn to the carburetor body not to do its job. Simply put, the needle valve will not let the fuel mixture through. Under such circumstances, the saw does not work.
Why does it stall Idling
Related posts
The first and most common cause of this malfunction is the incorrect carburetor adjustment. It is possible to adjust the idle speed without the help of others, for this purpose you need to have a Stihl adjustment screwdriver, which is supplied with the unit. The adjustment hole is located on the right side of the Stihl 180 saw on the handle and is indicated by the signs “-” and “”.
If chainsaw Stihl it does not keep revolutions and stalls idling, there is an option to practically 90% doubt that it has a violation in the fuel pump system, usually it is air leaking into the crankcase through the gasket of the sump, or, much more often, through the crankshaft oil seals. Air suction reduces or generally stops the impulse, which is supplied through special channels to the fuel pump of the chainsaw, by one hundred percent. And so this, the Stihl 180 chainsaw does not receive the right amount of fuel and stalls at idle.
Diagnostics can be done using a special device called a vacuum gauge.
KEY-DOP
The second method to check the performance of the oil seals is to pour gasoline into the engine crankcase and look for them if the oil seals allow gasoline to pass through, which means they will provide normal pressure in the crankcase, which will make idling impossible. And while working at high speeds, with leaky seals, there is the possibility of jamming of the crankshaft bearings.
The method for checking the crankcase and Stihl 180 oil seals for density is as follows:
- The top cover is removed.
- The air filter housing and the carburetor are dismantled.
- The handle of the chainsaw is removed.
- The starter is untwisted and removed.
- On the reverse side of the starter, the side cover and drive sprocket are removed.
- A piston stopper is installed in the spark plug hole or a cord is stuffed into the cylinder from an old starter with knots imposed on it.
- The flywheel and clutch are unscrewed, after which the parts are removed. It is worth knowing that the clutch of the chainsaw has a left-hand thread and is unscrewed clockwise.
- The gear wheel of the oil pump drive is removed.
Having disassembled the Stihl MS 180 chainsaw, we meet oil seals, after which it is necessary to fill the crankcase with gasoline and to check for leaks. It is possible to fill the crankcase through the fuel window in the cylinder, for this purpose the piston must be raised very high. If leaks are found, you need to change the defective oil seals, or re-seal the pallet. You can assemble Stihl 180 following the reverse sequence of the method.
KEY-DOP
Why stalls at full speed
Often we hear the question of why the chainsaw stalls at full speed. You will like a few circumstances. Firstly, it is necessary to consider how exactly the saw stalled. Let’s say the tool worked fine and suddenly, without any obvious circumstances, it suddenly died out and, with all this, the starter does not crank. Under these circumstances, there is an option to be 100% sure that the chainsaw is jammed and it is necessary to begin its serious repair.
The second situation is when the Stihl 180 chainsaw worked normally, then evenly over the course of a short time it lost power and died out, in this case the cylinder overheats. Under such circumstances, most likely the reason is air leakage under the rubber pipe connecting the carburetor to the cylinder or its rupture. The mixture was leaner, and the result was overheating. There is an option to remove the cause by changing the nozzle.
Conclusion
If the Stihl MC 180 chainsaw stalls at idle, does not gain power when you press the gas, or generally stalls at full speed, you need to diagnose the fuel accounting system and inspect the crankcase for density. This is done without the help of others of course, but you need to have certain abilities. If you are practically unfamiliar with push-pull saws, it is better to turn to specialists, because this technique is rather capricious and any mistakes are expensive.
Related posts
Stihl 230 Stalls When You Give Gas
Prerequisites why the chainsaw starts and stalls
A chainsaw has long been not a luxury, but the right equipment for those who have a summer cottage or home ownership. But, just as it doesn’t matter what other technique, this common hearing instrument tends to fail, regardless of a simple device.
Systematization of major defects means:
- complete lack of motor plant
- the engine starts and stalls
- unbalanced tool operation
- work stop at load
- loss of power.
If the chainsaw does not start completely, you will like the reason more in the following:
- Manufacturing defect
- Lack of fuel
- Tasks with starting an accounting ignition system
- No spark from spark plugs
- Bad fuel mixture
- clogged carburetor
- Difficulties with high voltage wire
- Lack of compression.
Why does the chainsaw start and stall, what should I do then? You need to carefully consider the prerequisites for this purpose to you.
Chainsaw starts and stalls: reason, video
The reason that the chainsaw can stall immediately after the factory lies in the problems of a certain part of the equipment.
- The most obvious reason why a chainsaw is wound up and stalled may be a low fuel level in the tank. Proof of this is the halt of the tool when tilted, when the remaining fuel accumulates in a certain place in the fuel tank. With poor fuel, a problem with the service of the chainsaw may also appear, in such circumstances it must be completely changed.
- Clogged breather, which significantly reduces fuel consumption to the engine.
- The missing contact of the wire cap with the candle, which leads to strong heating of the candle insulator. Contact deterioration may occur due to mechanical shear or carbon deposits.
- Damage to spark plugs.
- Muffler clogging, due to which the exhaust gas discharge is aggravated, resulting in engine shutdown. Therefore, a chainsaw can start and stall idling. Sludge in the silencer can also occur due to poor fuel or improper use of the tool.
- Bad carb adjustment.
- Piston group breakdown
- Difficulties with the fuel filter or pump. Here, gas can flow through the pump or flow poorly through the fuel filter to the carburetor. In the end, the chainsaw starts and stalls with increasing speed.
- Air filter is dirty. Difficulties with this element of equipment lead to the fact that, with excessive loads on the engine, it simply does not cope with having it due to clogging and stops. A similar result also occurs with an increase in speed.
- Short circuit due to the lack of a different amount of grease, also a problem with the chain brake.
Related posts
The saw stalls when you press the gas
KEY-DOP
This is one of the problems why, saw stalls by clicking on gas chainsaw repair.
Why the chainsaw starts up badly and stalls
With a bad start of the equipment “on a cold” problem, you will like it without compression, i.e. the rings are worn out due to their long service life; their replacement is required. With the premise that the engine starts poorly in an unheated state, there is a problem with the muffler, and also a bad contact between the spark plug and the wire.
Also, the reasons for the disgusting start will be wear or damage to the gasket, rubber cuff in the carburetor accelerator pump, due to which an additional air flow appears, leading to an increase in saw revolutions.
Troubleshooting
The operation of the equipment is suitable, with repeated inspection of the components to prevent breakage. To remove problems, you need to check what remains to do to our client the components of the equipment for their functioning.
If the chainsaw starts and stalls, the reason you like it is better fixed by your employees. If it is a shortage or improperly prepared fuel consistency, you need to fix it. For prevention at the time of the downtime of the chainsaw, the remaining fuel should always be drained.
It is necessary to carry out a repeated check of spark plugs. For all this, remove carbon deposits that clog the joint gap, and inspect the tips for fuel. The next premise of problems with spark plugs is that you will enjoy wetting them with gasoline. For this purpose you need to remove them, wipe with rags and leave to dry. Defective candles are replaced.
KEY-DOP
If there is no spark between the spark plug and the high-voltage wire, alas, if they have a good connection, you need to change the ignition unit.
Muffler clogging is a common cause of failure, when busy> The chainsaw starts up and stalls immediately. To eliminate the malfunction, it is necessary to dismantle the muffler, clean it from soot using sandpaper, in other words, a special chemical solution. If the chainsaw model is non-separable, chemical substances are poured into the system and the watch is there, then it is blown.
Related posts
The carburetor needs to be adjusted if the chainsaw stalls idling. Fine-tuning is a fairly time-consuming process, because usually it is done in service centers. However, on some models there are elements for its option, it is enough to turn the bolt half a turn to increase the speed of the chainsaw, the problems will be eliminated. If clogged nozzles, nozzles, channels and filters need to disassemble and clean the entire carburetor. If the seals, gaskets, cuffs are worn, they need to be changed, preventing the "suction" of air.
If there are problems with the fuel or air filter, you need to change the fuel pump to clean the air filter differently.
If the breather is clogged, clean it with an ordinary needle.
When the chainsaw starts up and stalls right away, the reason may lie in the incorrect operation of the chain. To eliminate troubles, the presence of oil in the tank for lubricating the chain is checked, in addition, the oil drain pipe for breaks or clogging.
Stihl 230 stalls when you give gas.
When inspecting the piston group, pay attention to the cylinder; if necessary, change it or the piston. A cylinder is bored to fit the dimensions of the new piston. If the piston with the cylinder is normal, pay attention to the shortcomings of the piston rings and the need to replace them.
over, it is necessary to keep under control the life of the parts indicated in the product passport, which include the drive sprocket, tire, chain, part of the anti-vibration accounting system, it is just right to create a substitution for them.
Video: Saw Stihl Gas Stalls
With a long conventional tool it is worth checking the condition of the fuel line. If the tube is cracked, you will have to change it to the latest.
Related posts
Saw Stihl Gas Stalls
What to do if a chainsaw dies
Hello, dear subscribers are not readers of my blog! Online Andrew Noack. We continue the topic of chainsaws. What is needed, I already said about 30 years about what should be checked in a chainsaw in order to know the cause of its malfunction. Today, I’ll move on to more valuable instructions so that you don’t look for the cause of the problem for a long time and don’t know how to solve it. A chainsaw is not a tool of any complexity, but you need to properly care for it. There are different cases with a chainsaw stalls when you press the gas, when in the load, and when it does not work at idle. If the chainsaw stalls under load, the saw may stall when gas is added. So. Let’s look at different situations together; we will not try to find the right solution.
If you find that the tool does not start at all, stalls, it’s not necessary to rush right into service center, Of course, try to solve the problem yourself.
Checking the main chainsaw system
We consistently check each system:
- Fuel tank. There is not enough fuel for you, as it is also called low-quality.
- The next tested spark plug is not a high-voltage wire. The saw stalls afterwards, but even sturdy models like Stihl and Partner can sometimes give. Take into account that the clearance of a candle normally does not exceed half a millimeter.
- If the above items are checked do not work correctly, go to the carburetor not the fuel filter. If a carburetor breaks down, contact a specialist.
Stalls at idle
At saw stalls at idle, a muffler is not a common cause of failure. It is easy to clean it yourself, for this purpose you do not need a high specialist.
In addition to cleaning, there is an option, but we treat it very carefully so as not to harm the internal parts of the device.
To adjust the carburetor, you need to find two bolts with the letters L not H. The latter must be turned, a little, only half a turn. Stihl lawnmower give gas to what it stalls give gas saw to stall. Why does the Stihl 180 stall when I press the gas or. He is responsible for the revolutions of the tool if necessary, will raise the idle speed.
Turns off when loaded
Chainsaw stalls When pressing gas. ADJUST THE CARBURETOR.
In the video, a fairly frequent malfunction of chainsaws is considered not a 100% carb setting method. How is this done.
Often powerful chainsaws stall from the load. Most likely you have a clogged fuel filter, it does not need to be replaced. If this does not help, then you need to check the quality of the fuel mixture and not prepare a new one.
Saw stops working when increasing speed
Localization of problem areas:
Filters are often clogged, especially when the chainsaw runs almost daily. The air filter is an option to disconnect do not wash under a stream of warm water. Dry before inserting into place.
If, after disconnecting the fuel hose from the carburetor with its use, no liquid escapes, then it has clogged. It can be cleaned or replaced with a new one.
With frequent use of the tool, a gasoline pump may fail. Each item has its own expiration date. It should be replaced in other words, contact a service center.
Saw turns off when turning
Horizontally, the fuel tube is at the bottom of the tank, if you tilt the tool, the fuel will not be able to completely cover it. Stihl 180 at full throttle. When loaded, the chain stops, while sawing. Why does the Stihl 180 stall when I press the gas or. This is the reason that the chainsaw stops working when tilted, since the tube levitates in the air and does not reach it <the right amount of mixture.
Hot issues
If you notice that the chainsaw starts without effort without warming up, and stalls after warming up. Do not start it until it cools, then here, you have several problems.
Everything, you somewhere of course the suction of a hose, stuffing box or gasket. If, inspect the muffler for carbon deposits. The third reason is the cylinder-piston group (CPG), whether there are burrs on another unevenness.
When carburetor adjustment is required. The next important cause of the malfunction is the ignition coil. In cases when the oil breaks down, the spark is lost otherwise it becomes very weak, which is not enough to ignite the fuel mixture.
There are cases when the master is trying hard the engine, then cold, then hot, thereby pumping fuel. Here you need to pull yourself together, transfer the flap to the "hot start", do not gradually start the tool. At the same time, we slow down the speed to an almost idle level of not 40-45 seconds as the oil warms up.
Saw stalls after letting go of the "gas"
Here you need to adjust the carburetor to check if there is a powerful air leak.
The most common cases of chainsaw breakdowns we have already seen. It only remains to be full that your saw will serve without breakdowns. Let’s say the Stihl saw 180 trimmer Stihl stalls when stihl stalls at full throttle. But such strong models as Stihl Non-Partner there are variations upon fail.
Do not rush to immediately run into service center, First, take my advice, so you will avoid the high cost of money.
If the article seemed interesting. share tips with friends through social networks. I say goodbye to you. Good luck not until new meetings in the blog!
Saw Stihl Give The Gas Stall
What to do if a chainsaw dies
Hello, dear subscribers are not readers of my blog! Online Andrey Noak. We continue the topic of chainsaws. What is needed, I have already said for 30 years that what should be checked in a chainsaw in order to know the cause of its malfunction. Today, I’ll move on to more valuable instructions so that you don’t look for the cause of the problem for a long time and don’t know how to solve it. A chainsaw is not a tool of any complexity, but you need to properly care for it. We also recommend that you familiarize yourself with the Stihl chainsaw Champion saw and let the gas stall. There are different cases, when a chainsaw stalls when you press the gas, when in a load, and when it does not work at idle. Let’s look at different situations together; we will not try to find the right solution.
If you find that the tool does not start at all and does not stall, then you will not rush to the service center right away, there is an option to try to solve the problem yourself.
Checking the main chainsaw system
We consistently check each system:
- Fuel tank. There is not enough fuel for you; in other words, it is of poor quality.
- The next tested spark plug is not a high-voltage wire. Take into account that the clearance of a candle normally does not exceed half a millimeter.
- If the above items are checked do not work correctly, go to the carburetor not the fuel filter. If a carburetor breaks down, contact a specialist.
Stalls at idle
At saw stalls at idle, a muffler is not a common cause of failure. Saw husqwarna 142 give gas saw husqwarna 142 give gas, stalls. Stihl recommends his. It can be easily cleaned independently; for this purpose a high specialist is not needed.
In addition to cleaning, there are options, but we treat the child very carefully so as not to harm the internal parts of the device.
To adjust the carburetor, you need to find two bolts with the letters L not H. The latter must be turned, a little, only half a turn. He is responsible for the revolutions of the tool if necessary, will raise the idle speed.
Turns off when loaded
Chainsaw stalls when pressing on gas. The chainsaw stalls when you press the gas.
In the video, a fairly frequent malfunction of chainsaws is considered not a 100% carb setting method. How is this done.
Often powerful chainsaws stall from the load. Mostly your fuel filter is clogged; it does not need to be replaced. If this does not help, then you need to check the quality of the fuel mixture and not prepare a new one.
Saw stops working when increasing speed
Localization of problem areas:
Filters are often clogged, especially when the chainsaw runs almost daily. Of course, disconnect the air filter and do not wash it under a stream of warm water. Prior to sticking to the place. thoroughly dry.
If, after disconnecting the fuel hose from the carburetor with its use, no liquid escapes, then it has clogged. Why does the Partner, Stihl and other models stall if the saw starts and stalls? There is an option to clean it, or replace it with a new one.
With frequent use of the tool, a gasoline pump may fail. Each item has its own expiration date. Answer: Stihl 180 chainsaw. Repair and treatment of childhood diseases. The saw starts and stalls after 10-20 seconds, start the test with the fuel filter. It should be replaced by another contact service center.
Saw turns off when turning
Horizontally, the fuel tube is at the bottom of the tank, if you tilt the tool, the fuel will not be able to completely cover it. This is the reason that the chainsaw stops working when tilted, since the tube levitates in the air, the required> image is the amount of the mixture.
Hot issues
If you notice that the chainsaw is easy to start without heating, and stalls after heating. Do not start it until it cools, then here, you have several problems.
Everything, somewhere you happen to have a suction hose, gland or gasket. If, inspect the muffler for carbon deposits. Lawnmower Stihl give gas it stalls. The third reason is the cylinder-piston group (CPG), whether there are burrs in other words, roughnesses.
When carburetor adjustment is required. An additional important cause of the malfunction is the ignition coil. In cases where the oil breaks down, the spark is lost; in other words, it becomes very weak, which is not enough to ignite the fuel mixture.
There are cases when the master is trying hard the engine, then cold, then hot, thereby pumping fuel. Here you need to pull yourself together, transfer the flap to the "hot start", do not gradually start the tool. In this case, we turn down the speed to an almost idle level of not 40-45 seconds, like oil warms up.
Saw stalls after releasing the "gas"
Here you need to adjust the carburetor to check if there is a powerful air leak.
The most common cases of chainsaw breakdowns we have already seen. It only remains to be full that your saw will serve without breakdowns. Even sturdy models like Stihl Non-Partner there are variations upon fail.
Do not rush to immediately run into service center, First, take my advice, so you will avoid the high cost of money.
If the article seemed interesting. share tips with friends through social networks. I say goodbye to you. Good luck not until new meetings in the blog!
Saw Stihl Stalls At Idle
For what reasons Stihl 180 stalls idling or full throttle
At least some tools can break and the Stihl MS 180 chainsaw is no exception. Now let’s try to understand issues such as: why the chainsaw stalls with an increase in speed, also at idle at full speed. We will examine the options for diagnosing and eliminating defects associated with this behavior of the Stihl 180 chainsaw.
IMPORTANT. An experienced electrician has leaked the secret to the network how to pay half the price of electricity, the legal way. Read more
Why the chainsaw stalls when you press the gas
Suppose a chainsaw normally idles, but with a sharp pressure on the gas stalls. What is the possible reason? It is immediately clear that it is not a matter of ignition (the absence of a spark), because if there was a malfunction in the ignition and the absence of a spark, the tool would simply not start. Means fuel system remains.
There are many defects in the fuel accounting system to determine a clear premise, which is why the chainsaw Stihl 180 stalls when you press the gas, you need to carry out its full diagnosis. We advise you to read about the widespread malfunctions of the Stihl 180 chainsaw and the elimination of these defects.
Filter check
The first thing to check is the fuel filter.
Sometimes, a clogged filter is unable to pass through the fuel mixture in sufficient quantities. Accordingly, a lack of fuel appears in the system, which leads to the fact that when you press the gas on the chainsaw, the fuel burns out, and a new one does not have time to arrive under the influence of which the Stihl chainsaw stalls. Also, with a clogged fuel filter, a noticeable drop in the power of the chainsaw at the highest revolutions can be observed, but this is with insignificant pollution.
KEY-DOP
Air filter
On the pages of the Internet, you can easily find information that the chainsaw Stihl 180 may stall due to severe contamination of the air filter. I would like to refute this incorrect information and say that the Stihl MC 180 carburetor is equipped with a compensator, which is designed and installed with the aim of taking the air necessary for the normal operation of the chainsaw Stihl 180, bypassing the dirty air filter. This power with a clogged air filter will fall a little, alas, it certainly will not stall. Still, the power may fall due to piston wear, the Stihl MS 180 piston chainsaw will already need to be repaired.
Related posts
Carburetor
One of the circumstances because of which the chainsaw does not develop momentum when you press the gas, but rather stall, this is a carb fault. Let’s say the Stihl 180 saw worked properly, but at the end it was set for a long time and did not even use it. After it was started, at the same time it works perfectly at idle, and when it is pressed on the gas, it can stall. Why does it stall? The reason is a stuck carburetor valve nozzle. This, this is not 100%, however, the possibility of such a malfunction is the highest. We advise you to read an article about the device and repair of the Stihl 180 carburetor.
To check the nozzle, you need to remove the carburetor and disassemble it. To remove, you need to unscrew the two nuts securing the air filter and the carburetor, then remove the air filter and the engine control lever, while disconnecting the throttle control rod from the carburetor. Further, you need to pull the carburetor slightly yourself, and disconnect the fuel supply hose.
Saw Stihl stalls at idle.
It is necessary to very carefully remove the fuel hose, and prepare a plug in advance, since fuel should go with its use.
After removing the carburetor, it must be purged and cleaned of dirt, only after which the carburetor, of course, untwist.
You need to untwist the cover of the main carburetor chamber, this one is busy> a compensator is installed on top. Then with a bolt of 8 mm and a length of more than 50 mm. We knock out the valve.
STIHL MS 180 repair / disassembly and assembly of the carburetor / stalls at idle
Chainsaw Stihl MS 180 has certain aspects that make owners worry, and is wasted on expensive.
It is necessary to knock out the valve by installing the carburetor on a wooden stand, this will ensure its protection against damage to the body.
If the nozzle is removed, of course blow it off using a compressor. The valve must allow air to flow in only one direction, if there is an option to freely blow the valve in both states, it means it is faulty and needs to be replaced with a new one. To assemble the chainsaw when the valve is repaired, it is necessary in compliance with the reverse disassembly sequence.
You can see clearly how the carburetor is being repaired, and more precisely, how to correctly knock the valve-nozzle out of the carburetor body by watching the video.
The next common reason why a saw may stall with increasing speed, air leaks in the carburetor. You only need to check this with a special tool, alas, you should see that if preventive work with the carburetor has not been carried out for a long time, then a new set of gaskets can be installed in the carburetor. Sometimes this helps to solve the problem with its depressurization.
KEY-DOP
When disassembling a carburetor for replacing gaskets, it is necessary to closely examine its needle-shaped valve, press on the rocker arm and control its lifting. When, in particular, if the Stihl chainsaw has stood for a long period with fuel in the carburetor, the needle may burn to the carburetor body not to do its job. Simply put, the needle valve will not let the fuel mixture through. Then, the saw doesn’t work.
Why stalls idling
Related posts
The first and most common cause of this malfunction is the incorrect carburetor adjustment. To adjust the idle speed there is an option without the help of others, for this purpose you need to have a Stihl adjustment screwdriver, which is supplied with the unit. The adjustment hole is located on the right side of the Stihl 180 saw on the handle and is indicated by the signs “-” and “”.
If the Stihl chainsaw does not maintain speed and stalls idling, there is of course no doubt 90% that it has a violation in the fuel pump system, usually it is air leaking into the crankcase through the pan gasket, or, much more often, through the crankshaft oil seals. Air suction reduces or, in general, completely stops the impulse, which is supplied through special channels to the fuel pump of the chainsaw. Upon completion of this, the Stihl 180 chainsaw does not receive the required amount of fuel and stalls at idle.
Diagnosis is possible using a special device called a vacuum gauge.
KEY-DOP
The second method to check the performance of the oil seals is to pour gasoline into the engine crankcase and look at them if the oil seals pass gasoline, which means they will provide normal pressure in the crankcase, which will make idling impossible. And while working at high speeds, with leaky seals, there is the possibility of jamming of the crankshaft bearings.
The method of checking the crankcase and oil seals Stihl 180 for density subsequent:
- The top cover is removed.
- The air filter housing and the carburetor are dismantled.
- The handle of the chainsaw is removed.
- The starter is untwisted and removed.
- On the reverse side of the starter, the side cover and drive sprocket are removed.
- A piston stop is installed in the spark plug hole; otherwise, a cord from an old starter with knots imposed on it is packed into the cylinder.
- The flywheel and clutch are unscrewed, then the parts are removed. It is worth knowing that the clutch of the chainsaw has a left-hand thread and is unscrewed clockwise.
- The gear wheel of the oil pump drive is removed.
Having disassembled the Stihl MS 180 chainsaw, you can meet the oil seals, after which you need to fill the crankcase with gasoline and check for leaks. Fill the crankcase, there is an option through the fuel window in the cylinder, for this purpose the piston must be raised very high. If leaks are found, you need to change the defective oil seals, or re-seal the pallet. To assemble Stihl 180 there is an option observing the reverse sequence of the method.
KEY-DOP
Why stalls at full speed
Often we hear the question of why the chainsaw stalls at full speed. There may be several circumstances. Everything, it is necessary to consider how exactly the saw stalled. Let’s say the tool worked fine and suddenly, without any obvious circumstances, it suddenly died out and at the same time the starter does not crank. Under these circumstances, there is an option to be 100% sure that the chainsaw is jammed and it is necessary to begin its serious repair.
The second situation is when the Stihl 180 chainsaw was working normally, then evenly over the course of a short time it lost power and died out, with all this, the cylinder overheats. Then, most likely the reason is air leaks under the rubber pipe connecting the carburetor to the cylinder or its rupture. The mixture was leaner, and the result was overheating. There is an option to remove the cause by changing the nozzle.
Conclusion
If the Stihl MC 180 chainsaw stalls at idle, does not gain power when you press the gas or generally stalls at full speed, you need to carry out fuel diagnostics allowing accounting (software) and inspecting the crankcase for density. This is done without the help of others of course, but you need to have certain abilities. If you are not much familiar with push-pull saws, it is better to turn to specialists, because this technique is rather capricious and any mistakes are expensive.
Related posts
Gaza Give Stoh Stihl 180
Why does the chainsaw stall when I press the gas: background and solution
There are frequent cases when owners of chainsaws encounter their breakdowns, it does not matter which model of this kind of equipment is, because the nature of breakdowns is practically the same for everyone. And then the chainsaw stalled and then what? Of course, you can add the equipment to special services that will fix your “iron friend” for a fee. Alas, as they say: why is it not easy to pay?
After all, there is an option to personally disassemble the tool and repair it, because breakage is possibly insignificant, in the service you will pay a lot. But than in order to repair the tool yourself, you need to be able to understand the causes of its breakdown and methods for eliminating defects. So let’s learn! Here it is possible to find answers to questions regarding situations when the instrument simply stalls after a specific pressure on the gas. What we need, let’s get started.
The main elements of chainsaws
Before you begin to delve into the issues of breakdowns and repair of the tool, for a start, let’s figure out what a chainsaw actually consists of. At first, I would like to note that this tool belongs to the category of technology in which the work required is directly dependent on the gasoline engine.
It is also important that chainsaws are equipped with a single cylinder engine, and whose work is done on such a fuel as gasoline. It should be noted that, not paying attention to the similarity with other tools, it does not have a gearbox. And it is replaced by a typical single-stage chain transmission, a means in which the movement of the chain itself (saw) is required.
You give gas to stoh Stihl 180.
In fact, a chainsaw is a fairly common design, however, this does not prevent it from being reliable, convenient and able to fully provide a concrete uninterrupted and cyclic operation even in fairly complex criteria. This tool consists of a huge range of certain “vital” parts for its correct and productive work. This is a carburetor, a device for a specific chain tension, a tire equipped with a chain and other elements.
Before buying a chainsaw, be sure to explore what remains to do for our client options, and choose the brand of chainsaw suitable for you.
To simplify the choice for you, we have compiled a rating of chainsaws for your company for reliability.
If you have a limited budget, then read the article about Russian manufacturers of chainsaws.
Description and possible causes of failure. Do-it-yourself troubleshooting
Read the same
Chainsaws are quite reliable and lightweight designs. If it is true to take care of them and handle it based on the advice of the manufacturer, then they become unusable and very rarely and quite quickly various failures are eliminated. If you are faced with this situation and would like to repair your own tool yourself without resorting to expert help, then delve into the information below.
As a matter of fact, it is impossible to determine unambiguously and precisely the reason why the tool does not start or stalls when you press the gas, because there are enough reasons for this. Alas, remember that starting from the right studio selection that a chainsaw is equipped with a conventional two-stroke engine, conditions such as lubrication, fuel, spark and air are important for its effective performance.
Chainsaw Fuel Tank
As it follows, the carburetor is specifically engaged in the production of the fuel-air consistency, the filter purifies the air from dust, the ignition unit and the spark make a spark, there is lubricant in gasoline.
That is why the search for the circumstances of this kind of failure is necessary in alternate order, starting particularly from light and evenly moving to the complex. And such actions is a fundamental factor in proper repair, because the person who, without thinking, begins to deal with the analysis of the carburetor, brings it to risk. Because of that kind the unit must be repaired or adjusted directly in special workshops (read about carb adjustment).
-
The important fact is that for trouble-free operation of the tool, it is necessary to be quite careful about fuel directly. Since if this kind of mixture is not prepared correctly, then most chainsaws simply will not start. Therefore, not every owner will guess the reason for the breakdown in the fuel. That is why in order for your tool to always work correctly, you need to use exclusively high-quality gasoline for the mixture.
Stihl 180. Classics of the genre. Does not develop momentum
This is one of the problems why, saw stalls by clicking on gas chainsaw repair.
And also use only the oil that is made by the manufacturer of your tool. In addition, it is important to prepare this kind of mixture in the amount that you accurately use in one or two weeks, but no more (see the proportion of gasoline and chainsaw oil).
Since in another case, overexposure of the mixture directly in the canister will lead to the fact that it will lose all its octane properties and this will lead to significant problems with the tool.
Read the same
Do not forget that by inspecting the candles you can get significant information regarding the breakdown of the chainsaw. Since if its surface is dry, the reason for this is the cylinder, which does not directly supply fuel. That is why you will have to step by step check the entire spectrum of its submission. If the candle is all in black soot, this means that the carburetor is not working properly, that is, it either supplies a lot of fuel or pours oil directly into gasoline.
Since, for example, the Stihl chainsaw stalls when you press the gas for a simple reason, namely a simple clogging of the direct breather.
In order to solve this kind of problem, all you have to do is disconnect the hose (fuel) from the carburetor and pay attention to whether fuel is leaking from it. Since if the mixture flows in a full stream, this means that the breather is not dirty, but if it is the other way around, then the cause of the breakdown was found.
But if after inspection you find that there is no damage to either the piston or the cylinder, in this case the cause may lie directly in the rings (piston). For this kind of check, it is necessary to insert a piston into the cylinder and gently begin to swing it by means of a connecting rod. If suddenly you feel a backlash then the rings need to be replaced, as they have already worn out.
Many people ask the question: why does the chainsaw stall when I press the gas? The answer may also lie in insufficient chain lubrication (see oil for the chainsaw chain), as the oil pipe may leak or the direct channels may be clogged. That is why pay attention to the chain, because if it is dry, without delay, start cleaning the channels that supply oil directly to the tool bar. After that, examine in detail the parts where the oil pump fittings are connected to the pipes. But if you notice that the oil is leaking at the joints, or if there are cracks on the pipes themselves, then in the first case, seal the leakage points with sealant, and the pipes will have to be replaced.
Additional tips
First of all, what you should remember when acquiring this kind of tool is that certain parts of the saw must be replaced with new ones after their useful life has expired (passport). It is for this reason that the instruction should always be at your fingertips, since everything is described in detail there.
These details include: asterisk (leading), bus, part of the system (anti-vibration), as well as a chain. Since we should not forget that if this “stuffing” is not replaced with a new one at the right time, then these worn-out spare parts will negatively affect the rest of the chainsaw. For this reason, often enough do a check of the depth of the direct tooth extraction. Remember that it should not be higher than a week of 0.5 mm.
To summarize.
Definitely, every thing we have purchased has its own expiration date and sooner or later it breaks and how insulting it is when the degree of breakdown is so great that it cannot be repaired. But you must admit that quite often we simply neglect the technique (see about proper operation and how to cut down a tree correctly so that it falls in the right direction), and when it stops working, then we try to find ways to fix the breakdowns, turning to a huge number of services.
But remember that even though the equipment breaks, we can extend its “life”. All that is needed is to simply look after her, run in after replacing parts (see how chains are run in here) and keep her spare parts clean and tidy. And then, undoubtedly, it will serve for many more years. It is also important to use exclusively high-quality spare parts and “additives” (see nozzles for chainsaws). Then your equipment will run smoothly, and you simply forget what repair is.
We also recommend that you familiarize yourself with the Stihl ms 180 chainsaw.