Briefly about the line
Taking into account the models of the tool, the thickness of the line is 1.2-4 mm. There are such configurations:
- Round. the most durable;
- Curly. for soft grass;
- Twisted or notched. for thin grass;
- Professional, suitable NOT for all instrument models.
When changing the cutting thread, you need to choose the one that suits your trimmer type. Preference should be given to Specialized. Before tucking the line into the trimmer spool, it is best to soak it in water for half an hour. Then it will become more elastic and stronger.
How to fill the line in the trimmer so that working with it does not get tired
Many summer residents use a trimmer to combat weeds. a scythe with an electric or gasoline engine. It is convenient when working in hard-to-reach places for a lawn mower: in fences, flower beds, houses, in a garden on narrow aisles, and can cut small branches. The main element of this miracle technique is an ordinary fishing line, wound on a reel. The device is simple, but the cutting part wears out quickly and requires replacement. And the question of how to fill the line in the trimmer worries many owners of summer cottages.
How to quickly remove the coil from the tool
Before the thread is wound on a bobbin, it must be removed. over, the methods of removal depend on the characteristics of the instrument. On a trimmer with a motor in the very ground, the coil has two side buttons, when pressed, part of the body is separated along with the thread winding devices.
On tools with a bent barbell, the lamb on the fixture is moved counterclockwise; having disconnected it, they remove both the bobbins and the spring inside it. On a trimmer with a straight bar, fix it with a screwdriver, rotate it clockwise and remove it. Then the device is disassembled either with the help of latches or by moving its parts in different directions. Take out the spring from the coil.
Threading the line into the trimmer
The main question is how to properly wind the line on the trimmer reel, securely fix it there?
In the case of a device with one tendril, up to four meters of fishing line is unwound, one end is inserted into the hole inside it, fixing the fishing line, and moved in the direction indicated by the arrow. The end of the thread is fixed in a groove inside the bobbin so that it does not unwind when it is assembled. If the groove has comments, then this free end is fixed with a finger. Then the coil is assembled.
How to refuel the trimmer coil if it has two tendrils? In this case, they check how many grooves there are. one or two. In the first case, both tendrils are directed into a common groove, if there are two of them, then each of them. into its own. 2-4 meters of thread are passed through the hole in such a way that the free edges of the thread are of the same length, and twist the bobbin in the direction of the arrow-pointer. The ends of the thread are inserted into the grooves or held with your finger, the device is assembled and attached to the trimmers.
In a spool with two grooves, the same piece of thread is folded in the form of a loop, sent to the groove between them and the ends are wound simultaneously. Then repeat the previous assembly. With semi-automatic winding, the bobbins operate as follows. The fishing line is passed through a hole inside, its ends are fixed in the holes on the body, collect it and press the button. The thread can be easily wound in the correct direction.
It is important to remember that the cutting surface must be protected from solid objects so that it does not wear out. Otherwise, it will be necessary to constantly stop and, having removed the bobbins, replace the used fishing line. Let your work be NOT tedious and enjoyable!
See: How to Insert Line into Trimmer
How to wind the line on a reel lawn mowers: method one
Open the trimmer head before starting winding.
First, the amount of fishing line that we will wind on the bobbin is determined. The reel should NOT go over the sides, otherwise the reel will NOT be inserted into the casing.
After determining the length of the line, you can start threading it into the bobbin:
- The fishing line folds in half, leaving one edge 10-15 centimeters longer. The bobbin is divided into two parts by a central collar. It has a groove for the court, which needs to be bent in half. It will take effort to refuel;
- The direction of winding is important. The bobbin should have an arrow or inscription indicating the winding side. If there is a pointer, there should be an arrow on the mower head. The cord is wound in the opposite direction;
- The line should be wound as carefully as possible, the thread should be as tight as possible;
- Upon completion of the laying, the short end of the thread is fixed, it is inserted into the corresponding diameter groove on the side of the spool. The long end is secured on the opposite side;
- In the fixed fishing line, you need to cut the edges with a gap of about 10 centimeters;
- The loaded bobbin is installed in the mowing head. The whine edges are pulled up with the locking grooves;
- The cover is put on and the latches are fixed. It must be fully fixed.
What is the best trimmer line? How to reel lawn mowers?
With the help of a trimmer, mowing of lawns and clearing various areas of excess vegetation are performed. Appliances are suitable for domestic and professional use. Electric trimmers work with a fishing line and a knife. Before buying a braid, all components of the device are evaluated, including the choice of line.
Which trimmer line is better?
To choose a fishing line, you need to Pay attention to the thickness of the cord, the shape of the section, the material of the thread itself.
The cord thickness must match the parameters of the selected tool. Too thick line will entangle the thread on the spool, cause the engine to overheat and cause the bushings to wear out quickly.
According to the thickness of the fishing line, it is conditionally divided into several types:
- Within 1.2. 1.6 millimeters. Suitable for models up to 0.5 kW. Often these are electric braids;
- 2mm to 2.4mm. This size is the most demanded because it can handle young and tough grass. Installed on tools with a power of about 1 kW;
- 3mm to 3.2mm. Suitable for units powered by gasoline, which will be mowed by thick stems of Buryanov;
- Court 4 mm. Copes with overgrown areas.
To determine which line is suitable oblique, you can use one of the following methods:
- The thickness of the court must be indicated in the user’s manual;
- Manufacturers often print important data on the bobbin, including the permissible diameter;
- Move the line into the exit hole. It should go smoothly.
Attention is also paid to the shape of the section, since the thread does NOT cut, but interrupts the grass stem.
Types of cords by sectional shape:
- Round. A versatile option for cutting fresh and dry vegetation;
- Multifaceted on 3-6 sides. Tough and thick stems can be cut. But the consumption of such material is quite large, therefore it is suitable only for specific purposes;
- Curly. Has a star or square shape with a recess. The first is used for cutting fresh vegetation.
Trimmer line is made of different materials:
- Most suitable for lawn mowers is nylon line made of polyamide or propylene. Inexpensive options with polyethylene in the composition. They are NOT load-resistant and cannot withstand frequent temperature changes. Polypropylene fishing line will last longer if you soak it in water for half an hour;
- The strongest are strings with aluminum particles and diameters of about 4 millimeters.
Do not use metal wires or ropes, which may damage the instrument.
Based on the described parameters, you can choose the optimal fishing line for caring for the adjoining territories.
How to thread the line into the trimmer spool: the second method
Some coils can be loaded in a different way. Charges two lengths of thread, not one folded in half.
The line is replaced according to the following scheme:
- As in the first case, the length of the new thread is determined;
- One edge of the court is crocheted;
- At the bottom of the bobbin there are holes for fixing the fishing line, where the bent edge of the thread is inserted;
- The thread is wound behind the arrow on the spool. The winding level should NOT exceed the spool diameter;
- The same is done with the second bobbin cell;
- The edges of the line that stick out of the holes need to be cut. You can simply turn on the scythe, while the knife will cut them off. The line is trimmed manually with scissors if the court diameter is too large.
If the unit is properly filled, then working with an electric scythe with a fishing line and a knife is easy and hassle-free. She quickly copes with well-groomed areas and Overgrown territories.
How to quickly remove the coil from the tool
Before the thread is wound on a bobbin, it must be removed. over, the methods of removal depend on the characteristics of the instrument. On a trimmer with a motor in the very ground, the coil has two side buttons, when pressed, part of the body is separated along with the thread winding devices.
On tools with a bent barbell, the lamb on the fixture is moved counterclockwise; having disconnected it, they remove both the bobbins and the spring inside it. On a trimmer with a straight bar, fix it with a screwdriver, rotate it clockwise and remove it. Then the device is disassembled either with the help of latches or by moving its parts in different directions. Take out the spring from the coil.
What types of woods are there
The most common type of line, which fits almost all types of reels # 8212; round cord. This is an ordinary fishing line, suitable for cutting succulent grass, but it will be much more difficult to mow dead wood with it, and even more so it will not cope with shrubs.
As a rule, the diameter, which can mow young grass, and does not exceed 1.6 mm. The thicker the thread, the more coarse grass it can overcome.
Important! When choosing a trimmer line, you must follow the instructions for your tool, since a thin thread will increase the wear of the torque mechanism, and a thick thread will overload the engine.
There are fishing lines with sharp edges in the form of an asterisk or a square, this option is more adapted to mowing dry grass precisely due to the existing sharp edges, but its disadvantage is greater wear and tear and it is inferior in strength to round cord.
There are fishing lines with improved aerodynamics with characteristic dents, scales and notches, such a product makes less noise, but it is used only for lawn mowers, since the exit of such a thread from the reel is difficult, it is used most often with discs in which the segments are inserted. The disadvantage of such a product is its fragility.
Most often in gasoline trimmers with an engine with an output of more than 1.5 hp. Use cords with a metal cable inside. This thread is ideal for cutting dry grass and small bushes. The presence of a core has a positive effect on the wear resistance of this material. The disadvantage of such a cord is its price, which is significantly higher than the above listed opponents.
»How to put it on
How to change the line to the trimmer and which one is better to choose
Since we discussed the choice of trimmer in the previous article. Then today we will tell you how to properly fill the trimmer with fishing line, and which one is better to choose Based on the working conditions.
After you bought a trimmer and began to actively use it, sooner or later the question of replacing the fishing line will arise, since this is the most wearing out element in the tool, intensive use of the trimmer will lead to frequent replacement of consumables.
How to fill the line in the trimmer so that working with it does not get tired
Many summer residents use a trimmer to combat weeds. a scythe with an electric or gasoline engine. It is convenient when working in hard-to-reach places for a lawn mower: in fences, flower beds, houses, in a garden on narrow aisles, and can cut small branches. The main element of this miracle technique is an ordinary fishing line, wound on a reel. The device is simple, but the cutting part wears out quickly and requires replacement. And the question of how to fill the line in the trimmer worries many owners of summer cottages.
How to thread the line into the trimmer spool
In order to wind the line, it will take about 10-15 minutes. What is a trimmer coil? Plastic body with a cassette inside, which has a special hook for easy winding of the fishing line. Almost all trimmer reels have a similar fastening principle, this is a central screw-button, when pressed, it becomes possible to stretch the line of the required length. The photo below shows a few examples of different trimmer spools.
The bobbins of the trimmers, the motor of which is located in the ground itself, have a different attachment to the axis of rotation, they have two buttons on the coil on the sides, which must be wrung out, otherwise the whine replacement is not different from other cassettes.
The principle of correct winding of the fishing line is similar in all of the above cases, therefore, for example, consider the standard version with two tendrils.
To remove the spool with the fishing line, it is necessary to Unscrew, located in the center, the screw, but Note that the thread is left there, so it will have to be turned clockwise, this was done on purpose so that during operation It does not open under the influence of centrifugal force.
Next, using a screwdriver, disassemble the head and remove the spool, onto which the fishing line is directly wound. Having measured the required length and folded in half, you need to tuck the fishing line into the spool.We bring out, in total, its ends opposite each other (for this there are special slots for fixing).
After that, it is necessary to assemble the head in the reverse order, threading the ends of the cord into two corresponding holes.
If you have doubts or it is not entirely clear how to load the line on the trimmer, we recommend that you look at how to properly wind the line into the lawn mower. In this, step by step, the instructor will open the trimmer head, measure the required amount of line, usually from two to four meters, and demonstrate assembly and installation on the trimmer.
Section profile
The second main parameter of a mowing line is its profile. The section profile influences many technical characteristics of the line, such as: noise, brittleness, economy, cut quality and operation.
Let’s take a closer look at the most common line profiles, as well as their advantages and disadvantages.
Twisted square (pigtail)
This mowing line profile is a kind of symbiosis of square and round profiles. Here he inherited the square profile, cutting edges and noiselessness, but the round profile. resistance to fracture. This is a kind of “golden mean” among the profiles of the mowing line. The disadvantages include the fact that this profile sometimes gets entangled in the mowing head, so when it should be screwed onto the mowing woman as diligently as possible.
| Advantages | limitations |
| NOT brittle | expensive |
| silent | gets tangled in the mowing head |
Square profile
This profile is a good choice, since of all the profiles it has the sharpest edge, thanks to which it copes without any problems with such plants as burdock, horseradish, etc.
| Advantages | limitations |
| NOT noisy | brittle |
| sharpest edge | expensive |
Star profile
This profile has five medium-sharp cutting edges. The advantage of this profile is its low noise level, low grass spread and good cutting ability.
But there are also disadvantages. This profile is the most brittle of all profiles, as well as the most expensive.
| Advantages | limitations |
| NOT noisy | maximum brittle |
| good cut | expensive |
Diameter
The diameter of the line for lawn mowers and trimmers starts at 1 mm. And with a step of 0.1 mm ends at 4.00 mm. (Although there are also individual copies of 4,2-4,4, they require converted coils and forced engines)
Line with a diameter of 1.00 to 1.8 mm. Typically used in electric trimmers with a bottom motor.
On trimmers with an overhead engine (they are more powerful), you can already use a line with a diameter of 1.6-2.4 mm.
On lawn mowers with 1E34F and 1E36F engines, you can safely use line from 1.8 to 2.7 mm.
Fishing line with a diameter of 3-3.4 mm. Can be used on powerful lawn mowers with 1E40F engine.
For heavy and professional mowing of large areas, you can use a mowing line of 3.6-4.00 mm, but it must be borne in mind that to work with such a line you will need special reinforced spools and powerful Brush cutters with 1E44F engines.
Therefore, when choosing a line, be sure to consider the power of your engine and the manufacturer’s recommendations. In addition to the motor, also pay attention to the reel, as each reel is designed for a specific range of line, as a rule, the maximum line diameter is indicated on the body of the reel, bobbin or in the markings. If you lose sight of this moment, then took a thicker line. You just don’t put it in the reel.
How to choose line for trimmer and lawn mowers
There is a wide variety of lawn mowers and trimmers on the market today, and the question naturally arises: “What kind of lawn mowing line to choose?” Therefore, in today’s review, we will try to clarify this topic.
The mowing line has two main parameters: diameter and section profile.
Round profile.
| Advantages | limitations |
| cheap | the noisiest |
| fracture resistant | DOES NOT cut, but tears the grass |
| DOES NOT break the coil | scatters grass heavily |
Reinforced line
It is also necessary to highlight reinforced fishing line in a separate group. This mowing line has two layers, one outer layer and one inner layer. The inner layer consists of reinforced plastic, which significantly reduces line fragility. Such a line does NOT break, but simply wears out physically, so a reinforced line has a longer service life than a regular line. As for its profile, it is exactly the same as in a conventional mowing line: round, star, square, pigtail, etc.
There are also exotic profiles: Swirling Star
Saw profile
Heptagon (heptagon)
Double ellipse
Beads
But since profile data is practically not found in our market, it makes no sense to dwell on them in more detail.
Change the line to the trimmer!
Taking into account the models of the tool, the thickness of the line is 1.2-4 mm.
There are such varieties of it:
- Round. the most durable;
- Curly. for soft grass;
- Twisted or notched. for thin grass;
- Professional, suitable NOT for all instrument models.
When changing the cutting thread, you need to choose the one that suits your trimmer type. Preference should be given to Specialized fishing line, it is of higher quality, it will last longer and will NOT break the tool.
Line thickness calculated by the manufacturer Based on engine power.
Before tucking the line into the trimmer spool, it is better to soak it in water for half an hour, then it will become more elastic and stronger.
Coil types:
Non-automatic reel with one tendril
Semi-automatic single section coil with 2 tendrils
Semi-automatic two-piece reel with 2 tendrils
Line replacement
All modern trimming heads have three types of line feed:
- Manual;
- Automatic;
- Semi-automatic.
Before replacing the thread, you must remove the bobbins. Removal methods depend on the characteristics of the instrument.
On a trimmer with a motor in the very ground, the coil has two side buttons, when pressed, part of the body is separated along with the thread winding devices. On tools with a bent barbell, the lamb on the fixture is moved counterclockwise; disconnecting it, remove both the bobbins and the spring inside it.
On a trimmer with a straight bar, fix it with a screwdriver, rotate it clockwise and remove it. Then the device is disassembled either with the help of latches or by moving its parts in different directions. Take out the spring from the coil.
In the case of a device with one tendril, up to four meters of fishing line is unwound, one end is inserted into the hole inside it, fixing the fishing line, and moved in the direction indicated by the arrow. The end of the thread is fixed in a groove inside the bobbin so that it does not unwind when it is assembled. If the groove has comments, then this free end is fixed with a finger. Then the coil is assembled.
In the case of a trimmer coil with two tendrils.
In this case, check how many grooves it has. one or two.
In the first case, both tendrils are directed into a common groove, if there are two of them, then each of them. into its own. 2-4 meters of line is passed through the hole so that the free edges of the line are the same length, and the reel is twisted in the direction of the arrow-pointer. The ends of the thread are inserted into the grooves or held with your finger, the device is assembled and attached to the trimmers.
In a spool with two grooves, the same piece of thread is folded in the form of a loop, sent to the groove between them and the ends are wound simultaneously. Then repeat the previous assembly.
Automatic and semi-automatic line feeding methods are more user-friendly.
With semi-automatic winding of the bobbin, the line is passed through the hole inside, its ends are fixed in the holes on the body, assemble it and press the button. The main thing is to observe the direction in which you wind the line. Then the line can be easily wound in the right direction.
It is important to remember that the cutting surface must be protected from solid objects so that it does not wear out.
Types of trimmer line
There are 3 main types of trimmer line: round, grooved and curly.
- Round trimmer line is the most popular. It is subdivided into commercial and premium subtypes, the difference between which lies in the quality of material, packaging and price.
- There are several types of trimmer line with a notch. The most popular is with spiral grooves to reduce operating noise. Usually used for battery and wire electric scythe.
- Curly trimmer line is the most varied line of line. Curly line can be triangular, square, rhomboid, pentagonal, hexagonal, octagonal, star-shaped, X-shaped.
Trimmers and chainsaws
Trimmer line (English. Trimmer line) is a nylon cord with a thickness of 0.4 to 4 mm of various cross-sectional shapes, designed for cutting grass by interrupting plants with a trimmer line, which is tensioned by centrifugal force from high turns of the trimmer head.
How to replace trimmer line
The line in the trimmer head may run out at the most inopportune moment, when a lot is not yet finished. This is a quick guide to replacing the trimmer line (replacing the line or trimmer string (.
6 types of trimmer line for various purposes, which are divided by diameter and sectional shape
Round Premium is a high performance all-purpose trimmer line. Made in 5 diameters, durable and wear-resistant.
Silent trimmer line. with spiral grooves that significantly reduce line whistle through the air. It is usually used in the trimmer heads of electric and battery lawn mowers, which work much quieter on gasoline models.
Round commercial. for heavy work. Trimmer line that is springy. Resistant to tear and wear.
Square trimmer line. Designed for dense and hard weeds (for professionals).
Pentahedral (armor-piercing trimmer line). Designed for heavy weeds between concrete, brick, stone, posts, netting, etc.
X-shaped trimmer line. Designed for soft grass that needs a lot of detail. Resistant to tearing at high temperatures.
Basic requirements for trimmer line:
- Wear resistance and mechanical tensile and abrasion resistance.
- Elasticity needed to wrap the line around the trimmer head drum and NOT break into solid obstacles.
- Resistant to temperature extremes, ultraviolet radiation and drying out during storage.
According to the type of trimmer line, it is divided into solid and braided.
The trimming line is made of nylon. Rather, its camping materials are polyamide and polypropylene. The disadvantage of polypropylene is that such a trimmer line dries out and becomes brittle during long-term storage in coils (before insertion, it is better to soak such a line in water for 0.5-2 hours). Manufacturers can add polyethylene to cheap fishing lines, which significantly reduces the wear resistance of the trimmer line. Manufacturers add aluminum to more expensive lines to increase the strength and durability of the trimmer line.
How to replace the line in the trimmer head. How to change the line in the Black Decker trimmer head
Disconnect the trimmer. Before changing the line in the Black Decker trimmer head, first switch off the trimmer and remove the battery.
Press down on the latches on the sides of the trim head and remove the cover. The cover should be easy to remove.
Remove any remaining line from the spool and clean the cover and trimmer head housing of soil and grass.
Insert the line into the spool. The end of the line from the bay must be inserted into one of the holes, it is better to start from the outside, where the arrows are drawn. Then bend the end of the line with a 90 degree hook with a bent length of about 2 cm.Insert this hook into the hole in the drum (spool) of the trimmer head.
Wind the line evenly in the direction indicated by the arrows. It is not necessary to wind very tightly or very much and DO NOT cross the turns with each other, since during the operation the line heats up and can sinter and stops moving out of the trimmer head. Cut the line from the bay. Thread the end into the hole to fix it. Wind the other half of the drum in the same way.
Insert the wound drum into the trimmer head housing.
Thread the ends of the line through the holes in the trimmer head body.
Press the coil lightly to make it sit in place. Make sure the line inside the trimmer head is NOT tangled and extends.
Close the lid without distortions and so that you hear two distinct clicks, thus assembling the trimmer head. At the first high revolutions, the line will come out of the trimmer head, pulled into a string and cut to the desired length on the cut-off knife, located on the plastic protection of the trimmer.