Stihl lawn mower how to change a fishing line for a trimmer for a blade. Frequent errors

trimmer for grass gasoline stihl how to refuel a fishing line for a trimmer. We change the fishing line for a trimmer in a trimmer (lawn mower)

Step-by-step instructions of the Autocut 25-2 StiHl mowing head, Open the braid head by pressing the side of the recesses in it. Click inward first one side so that the constipation comes out of the hook, and then press the other. After that, remove the lid of the mowing head.

It is worth suffering a little.And the power of Hercules will not help you.Only with time you understand how to quickly disassemble it.

If you have a Chinese head.It will be disassembled a little easier (plastic is thin).

They are also found with the inscriptions “Push and Twist” in the translation “Press and turn”

After you remove the top cover, you need to get the cord holder, while be careful and do not lose the spring

Take two strings (about 2 meters). Insert the end of one string into one of the coil ears and wrap the string in the indicated direction. Make sure that the string is evenly distributed and tightly wound. Season the end of the string in one of the coil holes.

If the Chinese head.Measure the right amount of fishing line (4-5 meters) and fold it in half.

Throw a folded fishing line for a trimmer in the middle on the holder (it has a special slot) and begin to wind the cord so that every mustache lies in its own compartment of the holder.

Insert the coil into the mowing head. Pull the ends of the string from the coil holes and season them into a special groove of the mowing head

And here you perfectly understand that buying a fishing line with a diameter of 3 mm was your mistake. As a rule, the recommended diameter of the stihl 2 coils.4 mm

But if you have a Chinese head. Then this rule does not concern you. Some buyers said that 4 mm managed to put to put. True, the coil is quickly crashed.

Remove the mustache over the eyes and set the top cover of the head, combining the side latches.

In courses for sellers of STIHL technology, we were told that in order to increase efficiency it is necessary to throw a coil with a fishing line for 20 minutes into water. I have not tried it myself, but I think these guys will not deceive.

How to cut a bottle into a tape

Before proceeding with the manufacture of a home.made cord, you will need to prepare the material itself, namely the plastic tape of the required width and length. To dissolve the PET bottle on the tape, use various devices, the manufacturing algorithm of which can be found on the Internet. If you are going to mow large areas overgrown with grass, and you will need a lot of home-made cord, then, of course, it makes sense to make a more complex bottlecore from the corner or U-shaped aluminum profile. The process of manufacturing a bottle.cutter is shown in this video.

But if you are not interested in the mass production of a plastic tape, then from time to time to dissolve the bottle on the strips in a simple way.

Thus, the entire plastic container will blossom into the tape of the same width.

A version of a bottle.cutter, which you will always have at hand, can be made from a conventional sharpener for pencils, preferably made of aluminum. In detail how to make it, shown in this video.

Winding profiles (cones)

Different models of coils of the coils of fishing line on the rogue are applied in different ways. High.quality products use a cylindrical and conical winding method. The laid fishing line for a trimmer to profile forms a flat fishing line for a trimmer. With a cylindrical winding, this fishing line for a trimmer is straight, parallel to the spool, with conical. inclined.

The straight conical shape narrows to the front side of the spool, the opposite. expands. Straight cone reduces the friction of the fishing line. The reverse styling type reduces the likelihood of spontaneous fishing line.

There is a third type of winding. chaotic. Usually used in cheap Chinese fishing rods. And if such a winding can still be tolerated using a regular fishing line for a trimmer, then you should refuse to use in such a coil of the cord. Bad castings, “beard”, overlaps and confusion are provided. This leads to failures during fishing, and can also ruin the mood for every fisherman.

How to wrap a fishing line for a trimmer to a coil correctly? We understand.

So, first we unscrew the nozzle. You need to do this, rotating the drum to the right. Here we have in our hands a drum with the remains of an old fishing line. We open it. Most often, the lid closes on the latches, which can be opened with a screwdriver by pulling it into the holes and slightly pressing it. Or you need to squeeze the lock and turn the lid towards the arrow. In this case, the cover itself must be held, t.to. There is a spring in the drums with automatically feeding the fishing line, which straighten up, can throw away all the internal parts of the drum. Gently taking out the coil, we remove the scraps of the fishing line from it.

Now you need to take 5 meters of a new fishing line and fold in half (to find the middle). In the middle part of the coil there is a recess (in some structures. a hole) for which you need to hook our fishing line for a trimmer. There is also an arrow on the coil showing the direction of winding. An important detail. if the coil has two compartments, then one half of the fishing line should be wrapped in one direction, and the second one in the other. Ending the winding, you need to leave 15-20 cm fishing line with free. There are also two recesses on the upper ring of the coil, through which these free ends need to be drawn. Directly with the winding itself, we coped.

The last stage of the process of replacing the fishing line is the assembly of the drum. First you need to install a spring and washers in your place. Then, holding the coil with one hand, the second you need to go through the ends of the fishing line into the corresponding holes on the sides of the nozzle. After that, install the coil in its place, pulling the fishing line for the trimmer and trying not to shift the spring. When all the internal elements of the nozzle will take their places you can close the drum with a lid. You just need to make some efforts so that the latches stand in their place. Voila! Kosyl nozzle is ready for work!

Self.manufacture of bobbin

Quite often, a trimmer for grass is operated in the distance from places where you can purchase spare parts for a spitt with its breakdown. In this case, instead of a broken mechanism, you can install a simple coil made in design made by yourself. To do this, you need a sheet of plywood (textolite, metal, etc.), eyes, screws or screws. The process includes several stages.

• A disk is cut out of the plywood sheet, which corresponds to the failed spool with a diameter.
• A hole is drilled in the center of the disk, which matches the diameter with a shaft of a trimmer for grass.
• Small eyes are attached to the opposite sides of the disk, which will serve to refuel the fishing line.
• Through the eyes, pass the fishing line for the trimmer and fix it with ordinary screws or screws. The coil is ready for work.

How to wind a fishing line for a trimmer coil for a Patriot grass?

Almost every newcomer when using a trimmer for grass is faced with the problem of fishing line changing. Despite the fact that changing the fishing line for the trimmer is very simple, you need to learn how to do it right. The replacement of the fishing line with proper dexterity will occupy no more than five minutes. it is enough just to constantly exercise in this. This article will consider the replacement of fishing line using the example of Patriot trimmers.

How to remove the coil and replace the fishing line for the trimmer

The owners of the trimmers, mainly beginners, confuse, bordering on panic, when it becomes necessary to change the cutting tool or fishing line for a trimmer in a reel. Very often, when trying to unscrew the mowing head, users simply make it unusable, not suspecting that it is unscrewed in the opposite direction. So that this does not happen, if you need to replace the tool, it is recommended to familiarize yourself with the step.by.step instructions given below.

• Before refueling the fishing line for the trimmer to the coil, drown out the engine of motorcycles or de.energize the ethletric trimmer for the grass to avoid injuries that may occur in case of accidental rotation of the cutting tool.
• Unscrew the nozzle mounted on the gearbox shaft. To do this, the shaft must be fixed by combining holes on the puck and on the axis, and inserting a metal rod or screwdriver into them.
• Unscrew the nozzle. You should know that the thread on the shaft is left. Therefore, to twist the coil of the trimmer for the grass should be right, that is, clockwise.
• Disassemble the mowing head. Most often, the head cover is attached to the fixers. To remove it, you need to drown these latches into the case, pressing the edges of the lid. If your trimmer has a semi.automatic mowing head, which has a button from below, then disassembling the nozzle should be done carefully, since you can lose a spring that sometimes flies away when removing the cover.
• Cut the required amount of fishing line. Usually its length is 5 meters. Use the cord of the diameter that is indicated in the instructions for the tool. It is not recommended to exceed the maximum diameter of the fishing line, since this will lead to increased load on the engine and greater consumption of gasoline.
• Find the middle of the segment of the cord, folding it in half. You will get a loop.
• Special grooves are cut out inside the coil (there may be holes). Insert the loop from the fishing line into this groove.
• Wind a fishing line for a trimmer to a coil, turning it counterclockwise. You need to refuel the cord as evenly as possible, the turns should be laid without ceiling and with good tension. When the winding is finished, leave the free ends of the fishing line about 20 cm long and fix them in the grooves located on the sides of the coil.
• Collect the braid head. Before you finally collect the nozzle, do not forget to insert a spring and washer (if it is available). Install the coil in the case, and prone the ends of the cord through the holes or eye.
• Dress the lid and fix it with latches.
• Screw the nozzle back to the gear shaft, also fixing it with a screwdriver. Tighten the coil of the trimmer for the grass will need to go to the left (against h. Arrows).

Rules for replacing knives on a trimmer for grass

If the disk on the trimmer is used regularly, it needs to be removed from time to time to remove and sharpen or change it to a new. This part can be made of metal or plastic, have a different number of blades, but the replacement process remains the same. over, this procedure is similar to the equipment of different manufacturers, whether Carver or Huter, but minor differences are possible. Changing the knife on the trimmer is quite simple if you observe safety precautions and know the correct procedure for which you can find a description of which you can in the user’s instructions. The whole process of replacing step by step, as well as the way of independent sharpening of knives, will be described in this material.

Material

It is not recommended to put metal knives on electrocos, since the design features make their use dangerous for the user. This is due to the curved shape of the bar, the absence of stops on the handles, as well as a high speed of rotation.

Important! Direct rod provides the safe use of a trimmer for grass at such moments when the disk, rotating, pushes into the obstacle. In this situation, he bounces back. towards a person, so a curved design can cause an injury. On trimmers with a flexible bar in terms of safety, plastic knives should be used

Their purpose is a mowing of soft grasses, dry. Whereas metal disks do a great job with high, thick, hard shoots, shrubs, as well as shoots of trees

On trimmers with a flexible bar in terms of safety, plastic knives should be used. Their purpose is a mowing of soft grasses, dry. Whereas metal disks do a great job with high, thick, hard shoots, shrubs, as well as shoots of trees.

Preparation for the winding of the fishing line

Previously, before the winding process, it is necessary to remove the coil with a fishing line from the body. Depending on the manufacturer, power and type (electric or gasoline), there are three structural types of trimmers:

Such a model provides for the possibility of installing a knife. Removing the coil in such models is carried out by means of two keys drowned in the case. To install a trimmer knife, it is necessary to combine the hole of the bobin and rod, and then insert the device in the form of a steel pin (screwdriver, iron bar). After fixing the coil, the case is easy to unscrew with your hands clockwise.

Method 2. two segments

The only difference from the method is no different from the method. two wound segments of fishing line, instead of one.

There are two special fixing nests on the coil (see drawing above).

They hook it previously formed on the fishing line, and begin to wrap a fishing line for a trimmer.

Winding is carried out in a special order

The winding needs to be carried out in the following order: first the lower fishing line for the trimmer, t.e. that which is closer to the fixing holes at the bottom of the coil, and only then the upper one, t.e. the one that will overlap the lower section.

The tips are made in the holes of the corps of the rogue trimmer for the grass. They are pulled to a click, which means that the fishing line for the trimmer has left the latch.

The tips are torn into the holes of the corps of the rogue trimmer for the grass

What can be used instead of fishing line

Many users of trimmers are wondering: how to replace the cord, by default used in this kind of devices? Unsafe experiments begin to carry out, installing metal or copper wire, metal cables or strings in a mowing head, as well as a regular fishing fishing line for a trimmer.

If you install a metal cable instead of fishing line, then a trimmer for grass turns into a dangerous device not only for the user, but also for others. This fact is explained by the fact that during the operation of the unit, the steel cable will be gradually shut up, its ends are gradually released, and small pieces of wire will fly in different directions at high speed.

And if you accidentally hook your or someone’s leg, working as an unit with a steel cable (wire), then a strong and deep section of the fabrics, and in some cases, amputation of the fingers are provided with you. The manufacturer is not in vain for these purposes, nylon uses, since it is quite light and durable, and when separating he does not fly away and cannot cause injury.

It is possible to use a fishing fishing line for a trimmer in a trimmer instead of a standard one, of course, but this will add unnecessary trouble, because it quickly wears out, breaks, mows slowly and does not fit for cutting hard grass. In addition, during the work, a lot of time is lost to replace the broken tool more than once.

In practice, the installation of a regular fishing line is justified if the user is going to mow grass near the fence, especially if he is from a rabid grid. In this case, in order to protect the standard and sometimes expensive cord from wear, it changes to a fishing fishing line for a trimmer, which is not a pity. Usually, in order to change the cord to a fishing line for a trimmer, it must be selected the greatest thickness-2-3 mm.

Installation of a metal cable: pros and cons of

The most common undertaking on the topic “How to replace a fishing line for a trimmer trimmer for grass?”, This is the use of a steel cable. In fact, in terms of efficiency, a metal cable is much better than a standard option. It is almost not susceptible to wear, and the grass is certainly no worse. Nevertheless, you need to understand that manufacturers do not just use a polymer fishing line for a trimmer, and not an iron cable.

Unfortunately, the reverse side of wear resistance consists in the increased wear of the transmission of the lawn mower. Due to the fact that the fishing line for a trimmer breaks, it does not overload the mechanical part of the device, but simply wear out as you use.

If desired, you can use a steel cable, but it is important that in the process it does not concern the protective casing in any way. The tips of the cable must be brewed so that they do not be blown up

How to replace

First you need to carry out preparatory work: process a fixing washer. Using the ruler, it is necessary to measure the straight line for the trimmer along the diameter of the washer, and then squeeze it in the grip of the received marks up.

It is recommended to indicate a point in advance in advance, where then it will be necessary to drill in order to prevent the drill slip. Make small holes on both sides, and then, using a thicker drill, increase these holes for the better passage of the chain.

The chain from the chainsaw should be installed so that it does not interfere with the leading axis of the tool. You need to insert it into the holes made, laying on the inside of the puck. The length of the chain should be equal to the distance to the puck, so that during the working trimmer for the grass, do not destroy the casing. From the inner wall of the washer, it is good to weld a chain to it.

The preparation is completed on this. Next, you need to connect the made material to the trimmer, tightening the nut.

Working with a trimmer, it is important to remember your own safety precautions

In addition to the above cases, it is also worth paying attention to the wreckage of felled bushes. Young shoots can fly in different directions with high speed and strength, so before work it is worthwhile to wear tight protective clothes, a mask, a headdress, gloves, gloves

Also, there should not be animals or children near.

How to replace a fishing line for a trimmer on a STIHL motorcycle

About a year ago, the author of these lines bought the STIHL Motokos (Stihl, as they say in the common people) FS 38.

The fishing line that was in the herbs was purchased for about a year and was enough, the last remnants were torn out when a dry tree branch was not seen in the grass. This is not the point.

The fishing line for the trimmer for replacement was also bought, along with a motorcycle (trimmer). But when the question arose of how to replace it, it caused difficulties. Searches on the Internet on request how to replace a fishing line for a trimmer STIHL did not lead to an instant result. precisely, the author of these lines came across a question about replacing the fishing line, asked by the user a specialist and answer: it is impossible to explain this, contact the dealer, he will show.

Well, he went to the dealer, the dealer showed, and he (the author of this entry), having arrived home, pulled out a fishing line for a trimmer and inserted it in front of the camera again. To yourself, if you need to remember, and show others. Those who are worried about the beauty of the house or garden.

So, see how to replace a fishing line for a trimmer on a STIHL motorcycle.

Update

After publishing the video, a method was found even easier, and a new video was shot. At the end of the video, bonus advice How to quickly adjust the length of the fishing line.

How to replace a fishing line for a trimmer Stihl trimmer

Winding a fishing line for a trimmer to a coil with one osik is very easy. In such structures, depending on the brand of a trimmer for grass, from two to five meters of the cord is placed. The edge of the fishing line in the spool must be tucked into a special hole or groove, after which the string is wound in the direction opposite to the rotation of the coil during operation.

Advice! To understand which way to wrap the thread, you should look at the corps of the spool. usually marks are made on it indicating the direction of movement of the coil during operation.

After the fishing line for the trimmer is windpowed, you need to leave a small piece (15-30 cm), walk into the output of the spool and collect the head again.

Coil with one working osik

The easiest option and a simple sequence of actions:

• The dimensions of the bobbin and the length of the original factory winding determine the length of the fishing line recommended for winding. 2 5 m.
• One end of the fishing line is inserted into the fixing technological hole located inside the spool.
• The fishing line for the trimmer is wound on the drum in reverse rotation of the spray in the trimmer product direction. as a rule, on the inside of the bobin, the arrow indicates which direction the winding is carried out.
• A small section of the fishing line is left free to output it. it is fixed in a specialized border on the inside of the bobbin, designed to keep the winding when assembling a spool in working condition.
• The left end of the fishing line is passed through the hole of the outer part of the bobbin.
• Half of the bobbin are collected and put on the bar of the trimmer device.

What is needed to replace the cord

With regular use of a trimmer for grass for begging grass, the discs are blunting, but they can be sharpened and continued to operate. The fishing line for a trimmer in the coil has the ability to end, so there is a need for refueling a new one, for which you need to determine the type of head and prepare the cord of the required thickness and length.

So, the mowing head is a cylindrical body in which a bastard is placed with a fishing line. Such a part is present both on electrimmers and on gasoline braids of any brands, whether it be Bosch, Makita, Stihl or other brand. There are three types of heads depending on the method of refueling and feeding the fishing line.

• The principle of operation of the heads of the automatic group is that they independently serve a fishing line for a trimmer, when a mowing reduces the speed of the motor. Such designs are convenient when working in large areas, but they have a shortage. a large cord consumption.
• The heads of the semi.automatic group are easy to operate. automatic fishing is performed at maximum engine speeds. To remove the cord lock, you need to carefully tap on the ground with the tool, after which the unlocked thread extends from the coil. The cut to the required length is made with a knife fixed on the protective casing.
• Trammers for grass with manual supply of the cord must first be turned off, and then independently pull out the fishing line for the trimmer.

On a note! The most convenient and optimal in price are semi.automatic coils with the cord.

Coils for electric and gasoline braids can be with one or two tastes of fishing line. The former are used to trim low herbal shoots, the latter. for beveling tall grass and small shrubs.

Solving possible problems with fishing line

Most of the problems associated with the fishing line are similar to different trimmers and are solved in a similar way.

Automatic winding of the fishing line on the reel

There is a variety of coils in which the automatic mechanism performs winding on its own. it is enough to correctly season the fishing line for a trimmer from the user. The fishing line for the trimmer is passed through the hole on the inside of the case, its antennae without winding are spread through the hole on the outer body, the bobbin is assembled, and when rotating the winding button for the trimmer, it is wound independently inside. It is impossible to make the winding incorrectly in such a spool: the mechanism itself will determine the correct direction, since it can only spin in one direction.

The coil does not spin

The reasons why the coil does not spin are similar to the lack of fishing line. This is the wrong or uneven winding of the string, its sticking, as well as the short ends of the cord, emerging from the holes.

Preparation for the replacement of fishing line

Before replacing the fishing line, you need to pull out, and then disassemble the head. It usually includes a casing, a spring (on some models), a bobbin with a fishing line, a lid. It is necessary to turn off the electric trimmer for the grass (or drown out gasoline) from the network, and then proceed to remove the coil. It can be recorded in two different ways: in the first case, it is necessary to completely disassemble the head, and in the second. just remove the gearbox from the shaft, to which it is attached.

• Find the latches on both sides, press and remove the lid to open the internal device of the head;
• A bobbin is located under the lid, it must be carefully pulled out of the case (sometimes a spring is hidden under it, it should also be carefully removed to the side so as not to lose);
• After removing the spool, it becomes noticeable in the center of the case with a fixing bolt (or screw), which must be unscrewed in a direction opposite to the clockwise movement;
• After removing the fasteners, it is necessary to hold the body with a swaying movement to remove the coil from the gear shaft.

The second method involves the following actions. Coil head is worn on the gear shaft. To disconnect it, you need to lock this shaft. Typically, in braids, for example, the brand “Champion” or “Stihl”, for this a hole is made into which a nail, rod or screwdriver is inserted. After fixing the shaft in a fixed position, you need to, holding the body, start rotating the head clockwise, since the thread on the shaft is usually applied to the left.

Now that the head is removed and dismantled, it is necessary to determine what thickness the cord should be. You can find out the suitable diameter for your trimmer for the grass by looking at the user’s guide or on the squash itself, it usually indicates such information. Another way is to insert the thread into the hole from which it is served. If the Sruna is without difficulty, it can be used to work.

Winding process

If your coil is designed to work with only one osmus, then everything is simple here. It is necessary to rewind 2-4 m of fishing line (depending on the size of the coil), find the hole for the trimmer on the inside of the coil, insert one end of the fishing line there and start to wind the fishing line for the trimmer in the direction in the reverse direction of rotation of the coil at the trimmer. The inside of the coil is usually indicated with an arrow in which the side is to wind a fishing line for a trimmer. Having wiped a fishing line for a trimmer, we leave its small piece unnecessary to put it out. We fix this piece in a special groove located on the inner part of the coil and designed so that at the time of collecting the coil of the fishing line for a trimmer does not unwind. If there is no such groove, then you will have to hold a fishing line for a trimmer with a finger, so as not to let it unwind during the further collection of the coil. Next, we take the outer part of the coil and spread the outer piece of fishing line into the available hole, collect and put the coil back to the trimmer for the grass.

If the coil is designed to work with two antennae, then we do the following. On the inside of the coil, we look at how many grooves are available for winding fishing. There may be one or two of them. If the groove is one, then both antennae are wound on this one groove. If there are two grooves, then each antennae is wound in a groove. The coil with one groove should have a through hole in which a fishing line for a trimmer is threaded. We open 2-4 m of fishing line, we extend it through this hole so that on each side of the fishing line it sticks the same. And we will simultaneously wrap both the antennae of the fishing line in one direction, the reverse direction of rotation of the coil in the trimmer and coinciding with the direction indicated by the arrow available on the inner part of the coil. We leave a little fishing fishing line, we fix the resulting ends in special grooves, and if they are not, we hold with your fingers. We spread both ends into the available holes on the outer body of the coil. Collect the coil and fasten it to the trimmer.

In the presence of two grooves, a piece of fishing line 2-4 m long is folded in half, we insert the loop in the groove between two grooves at the bending site, and we wind both the ends of the fishing line each in its groove at the same time. Further actions are similar to the previous option.

There are also coils, in which a fishing line for a trimmer is threaded through a through hole on the inside. After that, the ends of the fishing line, without wrapping, spread completely through the holes on the outer body of the coil, collect the coil and begin to rotate the button that is usually pressed in order to release the fishing line for the trimmer while it is worn out. Rotate the button. inside the trimmer fishing line is wound itself. At the same time, it will not work to twist it in the “wrong” direction, since it can spin only in one direction. If you get used to it, then you can wrap a fishing line for a trimmer to such a reel without even taking it out. you just need to combine the through hole of the internal drum with holes on the outer body of the coil, and then pass the fishing line for the trimmer in them.

That’s all on this issue. Successful winding!

In a model with one groove

The fishing line for the trimmer must be stretched into the hole, and its mustache should be folded together and aligned.

Then winding in the direction opposite to rotation of the bobbin on a mower is carried out. Often there is an arrow inside the coil, indicating how to put a fishing line for a trimmer correctly.

The ends of the string are fixed in special passes or simply temporarily adhere to with their hands and drawn into a hole located on the outside of the bobbin.

After that, the spool is closed and attached to the bar, after which the mitch is ready to work.

Replacing fishing line in the trimmer Stihl FSE 52

Trimmer for Daewoo Power Products Dabc 420

Gas trimmer for grass-editor, 26mm, square, Sturm!

Electric trimmer for Forward FGT-230/1500

Carver GBC-043MS trimmer for grass 1250 W / 1.7 liters.With.

STIHL trimmer coil (FS 38, 45. FSE 60, 71, 81).

Trimmer for grass gasoline front FBC-261/1100

Trimmer for grass gasoline front FBC-522/2600

Trimmer for grass gasoline front FBC-521/3000 Main

Electric trimmer for Forward FGT-230/1200

Trimmer for grass gasoline front FBC-522/3000 Main

Garden Trimmer for Smallcut Plus 350/23 (09806-20.000.00)

Replacing fishing line in trimmer: 2 simple ways

Trimmer for grass is the necessary and useful tool for a summer cottage and a private house. Many own and actively use it, but not everyone knows how to replace a fishing line for a trimmer in a trimmer, especially at first.

In this instruction, we will analyze the entire replacement process step by step. Looking ahead, there are two ways to refill a fishing rod with a fishing rod. There is no fundamental difference. the difference is that in the first case, one fishing line for a trimmer will be refueling, folded in half, and in the second there will be two segments of these forests.

Preparation for replacement

For clarity, a mowing head was removed from the motorcycles (Spool). To replace the fishing line you do not need to remove it, everything is done in place. It doesn’t take much time.

We disassemble the rogue of the trimmer for the grass-it holds on the clan locks. Remove the lid, pressing on the latches. If you do not have enough effort with your hands, then use the screwdriver.

Spool consists of the following:

The principle of action is as follows. By clicking on the button, the coil presses on the spring and leaves the fixing grooves in the lid of the spray. Holding the coil in this state, you can twist, thereby adjusting the length of the fishing line. When the button is released, the housing spring returns the coil to the original fixed state.

Below on the coil there are several holes for a different diameter of the forest. For different manufacturers of trimmers, they may differ. In some cases (as here) they are signed, in others there is no.

These holes are needed to fix the fishing line when replacing it. After winding on the labina of fishing line, the ends of the latter are inserted into them. This is necessary so that the forest does not unwind at the time the coil is installed in the trimmer body for grass. In other words, it facilitates the replacement of fishing line.

There are models without specifying the diameter of the consumable. Then, in order to find out what maximum forest diameter can be used, it is tried on by the openings of the fishing line out of the trimmer’s corps of the grass (see. Figure below).

The coil has two sections for the fishing line separated by a partition. They may not be. They are needed only to distinguish and facilitate the winding of the consumer.